Haier HSU-22LE04, HSU-12LE04, HSU-09LE04, HSU-18LE04 User Manual

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

FJT-12L FJT-18L

FJT-24L HSU-07LD03

HSU-09LE04 HSU-12LE04 HSU-18LE04

HSU-22LE04

Please read this operation manual before using the air conditioner.

0010511927

Cautions

The machine is adaptive in following situation

I. Applicable ambient temperature range:

Indoor

Cooling

Outdoor

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05/07RN-F or 245IEC57(YZW).

3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.

4. The distance between the indoor unit and the floor should be more than 2m.

5. The wiring method should be in line with the local wiring standard.

6. After installation, the power plug should be easily reached.

7. The waste battery should be disposed properly.

8. The appliance is not intended to use by young children or infirm persons without supervision.

9.Young children should be supervised ensure that they do not play with the appliance.

10.The appliance must be installed on strong enough supporter.

11.The wiring diagram is attached inside the machine.

Maximum: D.B / W.B Minimum: D.B / W.B

Maximum: D.B/ W.B Minimum: D.B

32oC/23oC 18oC/14oC

43oC/26oC 18oC

Parts and Functions

Indoor Unit

Inlet grille

Air filter

Horizontal flap

Use remote controller to adjust up and down air flow. (Don't adjust it manually.)

Power indicator

Lights up when unit starts.

Timer mode indicator

Lights up when Timer operation is selected.

Test running switch(manual)

Used only for test running in cooling when room temp. is below 16oC. Don't use it in normal operation.

Emergency switch(manual)

Used when remote controller is lost or defective. Unit will run temporarily.

Remote signal receiver

A beeping sound is generated when a signal from remote controller is received.

Operation mode indicator

Lights up during compressor running.

Actual inlet grille may vary from the one shown in the manual according to the product purchased

For 22k unit, the power plug is on the outdoor unit

Outdoor Unit

HSU-09LE04 HSU-07LD03

FJT-12L

OUTLET

INLET

HSU-12LE04 HSU-18LE04

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

FJT-18L FJT-24L

HSU-22LE04

Parts and Functions

Operation

2 3 4

14 15

Clock set

ON/OFF

MODE SET

FAN

SWING

SLEEP

LOCK RESET

A U T O

HEALTH

TEMP

TIMER

CLOCK

ON OFF

Buttons and display of the remote controller.

1. Mode display AUTO

COOL DRY

7 8

FAN

2. SWING display

3. FAN SPEED display

4. HEALTH display

5. SLEEP display

6. LOCK display

7. SIGNAL SENDING display

8. TIMER OFF display

9. TIMER ON display

10. CLOCK display

11. TEMP display

12. POWER ON/OFF

Used for unit start and stop.

13. MODE

Used to select AUTO run, COOL, DRY and FAN operation

14. FAN

Used to select fan speed LO, MED, HI, AUTO

15. HOUR

Used to set clock and timer setting.

16. SWING

Used to set auto fan direction.

17. SLEEP

Used to select sleep mode.

18. LOCK

Used to lock buttons and LCD display.

19. TEMP.

Used to select your desired temp.

20. SET

Used to confirm timer and clock settings.

21. TIMER

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF

22. CLOCK

Used to set correct time

23. RESET

Used to reset the controller back to normal condition.

24. HEALTH

Used to operate the healthy function

When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working.

NOTE: Cooling only unit do not have displays and functions related with heating

LO MED HIAUTO

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.

Parts and Functions

Operation

Buttons and display of the remote controller.

If the unit which you purchased has not healthy function, Remote controller should like the following figure:

13 14

2 3

A U T O

ON OFF

ON/OFF

MODE SET

FAN

SWING

SLEEP

LOCK RESET

TEMP

TIMER

CLOCK

5 6

Clock set

When unit is started for the first time and after replacing batteries in remote controlle clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickl After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working.

1. Mode display AUTO

COOL DRY FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL, DRY and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

Used to reset the controller back to

normal condition.

LO MED HIAUTO

NOTE: Cooling only unit do not have displays and functions related with heating

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.

+ 14 hidden pages