Haier HSU-18LEK03/(DB), HSU-24HEK03 Installation Manual

Installation Manual of Room Air Conditioner

No.0010518787

Read this manual before installation

1.Driver

2.Ha

cksaw

3.Hole core d

rill

4.Spanner(17,19 and 26mm)

5.

Torque wrench(17mm,22mm,26mm)

6.Pipe cutter

7.Fla

ring tool

8.Kni

fe

9.Nipper 12.Reamer

10.Gas leakage detector or
soap-and-

water solution

11.Measuring tape

Explain sufficiently the operating means to the user
according to this manual.

A

B

C

D

E

F

G

Optional parts for piping

Mark

Parts name

Non-adhesi

ve tape

Adhesi

ve tape

Saddle(L.S) with scr

ews

Connecting elect

ric cable

for indoor and outdoor

Drain hose

Heating insulating material

Piping hole c

over

Arrangement of piping directions

Rear left

Rear
right

Left

Below

Right

The marks from to in the figure are the parts numbers.

The distance between the indoor unit and the floor should be
more than 2m.

A

G

Attention must be paid to
the rising up of drain hose

mc5na

h

ter

om

m

c

0

1

n

a

h

t

e

r

o

m

m

c

0

1

n

a

h

t

e

r

o

m

A

C

No. Accessory parts

Remote controller

R-03 d

ry battery

Mounting plate

Drain hose

Steel nail, cement

Screw

Plastic cap

Drain-elbow

Cover

Cushion

1

1

2

3

4

5

6

7

8

9

10

2

1

1

6

4

1

1

4

1

Number
of
articles

Accessory parts

4X50

4X25

Pipe supporting plate

11

Connecting cable

1

m

c

0

1

n

a

h

t

e

r

o

m

m

c

0

6

n

a

h

t

e

r

o

m

m

c

5

1

n

a

h

t

e

r

o

m

m

c

0

1

n

a

h

t

e

r

o

m

D

E

Note:Cooling only units don't have Drain-elbow

Drawing for the installation of indoor and outdoor units

Necessary Tools for Installation

Selection of pipe

To this unit, both liquid and gas pipes shall be insulated

as they become Iow temperature in operation.

Use optional parts for piping set or pipes covered with

equivalent insulation material.

2

Liquid pipe ( )

For 07 09

6.35mm(1/4")

Gas pipe ( ) 9.52mm(3/8")

For 12 18

12.7mm(1/2")

HSU-09HEK03

HSU-09LEK03

HSU-12HEK03

HSU-12LEK03

6.35mm(1/4")

HSU-09LEK13
HSU-12LEK13
HSU-07LEK03
HSU-07HEK03

1.Fitting of the Mounting Plate and Positioning of the wall Hole

2.Making a Hole on the Wall and Fitting the Piping Hole Cover

When the mounting plate is first fixed

1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.

2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.

3. Find the wall hole location A using a measuring tape

Make a hole of 60 mm in diameter,
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation

Indoor unit

(Section of wall hole)

Piping hole pipe

Outdoor side

Thickness
of wall

Indoor side

Wall hole

60mm

G

A=145mm

B= 60mm

30mm

HSU-09LEK03/(DB)
HSU-12LEK03/(DB)

HSU-24LEK13

HSU-18LEK13

60mm

30mm

HSU-18LEK13

HSU-09HEK03

HSU-09LEK03

HSU-12HEK03

HSU-12LEK03

HSU-09LEK13
HSU-12LEK13
HSU-07LEK03
HSU-07HEK03

HSU-09LEK03/(DB)
HSU-12LEK03/(DB)

HSU-108CH09
HSU-138CH09

HSU-108CH09
HSU-138CH09

30mm

HSU-12LEK13-M

HSU-12LEK13-M

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

140

500

140

256

113.5

583

113.5

19 5.
3

Floor fixing dimensions

of the outdoor unit

(Unit:mm)

140 140415

280

15.88mm(5/8")

9.52mm(3/8")

For 24

HSU-24LEK13

A=145mm

B= 60mm

A=145mm

B=

HSU-18HEK03

HSU-18HEK03

HSU-24HEK03

HSU-24HEK03

HSU-18LEK03/(DB)

HSU-18LEK03/(DB)