Haier HSU-09LEK03/ (DB), HSU-12LEK03/ (DB), HSU-108CH09, HSU-138CH09 Operation Manual
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
0010519692
Contents
1
2-4
5
7
6.7
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-09LEK03/ (DB)
HSU-12LEK03/ (DB)
HSU-108CH09
HSU-138CH09
1
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
Parts and Functions
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
adjust up and down air flow Don't adjust it manually
adjust left and right air flow
Vertical blade
Remote controller
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:
Cooling only unit do not have displays and functions related with heating
(inside)
Power indicator
Timer mode indicator
Operation mode indicator
(Lights up when unit starts.)
(Lights up whenTimer operation is selected.)
(lights up when the compressor is on.)
Remote signal receiver
(A beeping sound is generated when a signal
from remote controller isreceived.)
Ambient temp display
When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
is displayed and this room temperature is only for reference.
Anion generator
Outdoor Unit
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
resetting key(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the
ries have been used up.
Please change batte
ries.
If the remote controller can't run normally during operation,
reload several minutes later.
batte
rem
ove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are a
ny display
after taking-out, just need to press reset key
Hint:
Loading of the battery
please
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly.
After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the
button is kept pressed,time will
will increase
TIMER
CLOCK
SET
SLEEP
POWER/SOFT
LIGHT
FAN
DRY
COOL
AU
TO
1. Mode display
2. SWING display
3. FAN SPEED display
4. SLEE
P display
5. LOCK display
6. SIGNAL SENDING
7. TIMER OFF display
8. TIMER ON display
9. CLOCK display
10
. TEMP display
11. POWER ON/OFF
Used for unit start and stop.
12. MODE
Used to select AUTO run, COOL,
DRY
HEAT and FAN operation.
13
.FAN
Used to select fan speed LO,
14. HOUR
Used to set clock and timer setting.
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and LCD display.
18. TEMP.SETTING
Used to select your desired temp.
LO MED HIAUTO
HEAT
1
2
3
5
6
7
8
9
10
4
ON/OFF
FAN
MODE
SWING
TIMER
CLOCK
SET
SLEEP
LOCK
RESET
11
12
14
15
16
17
13
18
19
20
21
22
POWER/SOFT
LIGHT
23
19. SET /
Used to confirm timer and clock
settings.Control the lightening and
extinguishing of the indoor LED
20
. TIMER
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF
21. CLOCK
Used to set correct time
22. RESET
Used to reset the controller back
23.
HOUR /
Used to set clock and timer setting.
Every time the button is pressed,
POWER/SOFT
POWER
SOFT
BLANK
LIGHT
HEALTH
24
24. HEALTH
Used to operate the healthy
23
MED, HI, AUTO
display board.
to normal condition.
function and LCD display.
display changes as follows:
2
Operation
Unit start / stop
AUTO LO MED HI
Note:
In DRY mode, when room temperature becomes lower than temp.
o
setting+2 C, unit will run intermittently at LOW speed regardless
In HEAT mode,warm air will blow out after a short periodof the time
When FAN is set to AUTO, the air conditioner automatically adjusts
next time,just press ON/OFF button and unit will run in previous status.
Remote controller can memorize each operation status. When starting it
Cooling only unit do not have displays and functions related with heating
Press ON/OFF button, unit starts or stops.
ON/OFF
FAN
HEALTH
FAN
MODE
SWING
According to the automatic choice
system in temperature in indoors
cold or make the hot movement
ON/OFF
HEALTH
FAN
MODE
automatically adjusts
1.
2.In FAN operation mode
Auto Operation
Cool Operation
FAN
MODE
SWING
Heat Operation
FAN
MODE
SWING
Dry Operation
FAN
MODE
SWING
Fan Operation
When FAN is set to AUTO,
the air conditioner
the fan speed according
to roomtemperature.
the unit will not operate
in COOL mode but only
in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled.
of FAN setting.
due to cold-draft prevention function.
the fan speed according to room temperature.
Note:
FAN
MODE
SWING
(1)
Air Flow Direction Adjustm
Select temp.setting
FAN
MODE
SWING
Operation
Mode
AUTO
Remote
Controller
Note
COOL
DRY
HEAT
FAN
In DRY mode, when room temperature becomes
lower than tem
p.setting+2
o
C,unit will run intermittently
at LOW speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
automatically adjusts the fan speed
temperature.
When
FAN is set to AUTO, the
according to room
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
Loading...