Haier HSU-12HEA03/R2-I, HSU-18HEA03/R2-I, HSU-09HEA03/R2 - annexe 1, HSU-12HEA03/R2 - annexe 2, HSU-18HEA03/R2 Installation Manual

INSTALLATION MANUAL

ROOM AIR CONDITIONER
WALL MOUNTED TYPE

NO.0010523234

Read this manual before installation

Explain sufficiently the operating means to the user

according to this manual.

HSU-12HEA03/R2-I
HSU-18HEA03/R2-I

HSU-09HEA03/R2-I

No.00105

1.Driver

2.Hacksaw

3.Hole core drill

4.Spanner(17,19 and 26mm)

5.Torque wrench(17mm,22mm,26mm)

6.Pipe cutter

7.Flaring tool

8.Knife

9.Nipper 12.Reamer

10.Gas leakage detector or
soap-and-

water solution

11.Measuring tape

A

B

C

D

E

F

G

Optional parts for piping

Ma

rk

Parts name

Non-adhesi

ve tape

Adhesive tape

Saddle(L.S) with screws

Connecting elect

ric cable

for indoor and outdoor

Drain hose

Heating insulating mate

rial

Piping hole c

over

Arrangement of piping directions

Rear left

Rear
right

Left

Bel

ow

Right

The marks from to in the figure are the parts numbers.

The distance bet

ween the indoor unit and the floor should be

more than 2m.

A

G

Attention must be paid to
the rising up of drain hose

m
c5n

a
h
t
e
ro

m

mc0

1

nah

t

e

r

o

m

m

c

0

1n

aht

e

r

o

m

A

C

No. Accessory parts

Remote controller

R-03 d

ry battery

Mounting plate

Drain hose

Steel nail, cement

Scr

ew

Plastic cap

Cover

Cushion

1

1

2

3

4

5

6

7

8

9

2

1

1

6

4

1

4

1

Number
of
articles

Accessory parts

4X50

4X25

Pipe supporting plate

m

c

0

1

na

h

t

e

r

om

m

c0

6

n

ah

t

er

om

m

c

5

1

n

a

h

ter

o

m

m

c

01

n

a

ht

er

o

m

D

E

Drawing for the installation of indoor and outdoor units

Necessary Tools for Installation

10

Drain-elbow

1

Liquid pipe ( )

For 09K .12K

6.35mm(1/4")

Gas pipe ( ) 9.52mm(3/8")

For 18K

6.35mm(1/4")

12.7mm(1/2")

Fixing of outdoor unit

Indoor Unit

Selection of Installation Place

Power Source

Selection of pipe

Outdoor Unit

Fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizontally.

When fitting the unit to wall surface, roof or rooftop, fix a supporter surely with nails
or wires in consideration of earthquake and strong wind.

If vibration may affect the house, fix the unit by attaching a vibration-proof mat.

Place, robust not causing vibration, where the body can be supported
sufficiently.
Place, not affected by heat or steam generated in the vicinity, where
inlet and outlet of the unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the
outdoor unit.
Place, where cold air can be spread in a room entirely.
Place, nearby a power receptacle, with enough space around. (Refer
to drawings).
Place where the distance of more than lm from televisions, radios,
wireless apparatuses and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the
indoor unit can receive signals when the fluorescent lamps in the room
are lightened.

Place, which is less affected by rain or direct sunlight and is
sufficiently ventilated.
Place, possible to bear the unit, where vibration and noise are
not increased.
Place, where discharged wind and noise do not cause a
nuisance to the neighbors.
Place, where a distance marked is available as illustrated
in the above figure.

Before inserting power plug into receptacle, check the voltage without fail. The power source is the same as the corresponding name plate.

Install an exclusive branch circuit of the power.

A receptacle shall be set up in a distance where the power cable can be reached. Do not extend the cable by cutting it.

To this unit, both liquid and gas pipes shall be insulated

as they become Iow temperature in operation.

Use optional parts for piping set or pipes covered with

equivalent insulation material.

2

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

HSU-12HEA03/R2-I

HSU-18HEA03/R2-I

HSU-09HEA03/R2-I

Floor fixing dimensions
of the outdoor unit
(Unit:mm)

580

115

115

319.5

Indoor unit

1.Fitting of the Mounting Plate and Positioning of the wall Hole

2.Making a Hole on the Wall and Fitting the Piping Hole Cover

When the mounting plate is first fixed

When the mounting plate is fixed side bar and lintel

1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be
fixed against the wall, then temporarily fasten the plate with one steel nail.

2. Make sure once more the proper level of the plate, by hanging a thread with a weight from
the central top of the plate, then fasten securely the plate with the attachment steel nail.

3. Find the wall hole location A using a measuring tape

Refer to the previous article, " When the mounting plate is first fixed ", for the
position of wall hole.

Fix to side bar and lintel a mounting bar, Which is separately sold, and then fasten

the plate to the fixed mounting bar.

Make a hole of 60 mm in diameter,
slightly descending to outside the wall.
Install piping hole cover and seal it
off with putty after installation

(Section of wall hole)

Piping hole pipe

Outdoor side

Thickness
of wall

Indoor side

Wall hole

60mm

3.Installation of the Indoor Unit

Drawing of pipe

[ Rear piping ]

Draw pipes and the drain hose, then fasten them with the adhesive tape

[ Left Left-rear piping ]

In case of left side piping, cut away, with a nipper, the lid for left piping.
In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear
piping which is marked on heat insulation materials.

3

G

A=145mm

B= 60mm

30mm