Haier HSU-12HD03, HSU-09H03/R2(DB), HSU-12H03/R2(DB), HSU-18H03/R2(DB), HSU-22H03/R2(DB) Operatiing Manual

...

No, 0010558081

HSU-09H03/R2(DB)

HSU-12H03/R2(DB)

HSU-18H03/R2(DB)

HSU-22H03/R2(DB)

HSU-12HB03/R2(DB)

HSU-12HD03/R2(DB)

Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment.

It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled.Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal.

Disposal of the old air conditioner

All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment.

The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads

All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.

Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.

Disposal of the packaging of your new air conditioner

Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly, operation and maintenance of the air conditioner.

The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction.

Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.

Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.

Installation shall be done by professional people, don't install unit by yourself.

For the purpose of the safety,the air conditioner must be properly grounded in accordance with specifications.

Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditioner.

Safety Instructions and Warnings

Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries.

Cautions

A breaker should be incorporated into fixed

and the distance between its two contacts

wiring.The breaker should be all-pole switch

should be not less than 3mm.

3. If the fuse of indoor unit on PC board is broken,please change it with the type of T. 3.15A/ 250V. If the fuse of outdoor unit is broken,change it with the type of T.25A/250V

Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver.

Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit.

The refrigerating circuit is leak-proof.

1.Applicable ambient temperature range:

Specifications

The machine is adaptive in following situation

10 .The power plug and connecting cable must have acquired the local attestation.

2. If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.

4. The wiring method should be in line with the local wiring standard.

5. After installation, the power plug should be easily reached.

6. The waste battery should be disposed properly.

7. The appliance is not intended for use by young children or infirm persons without supervision.

8. Young children should be supervised to ensure that they do not play with the appliance.

9.Please employ the proper power plug, which fit into the power supply cord.

Cooling

Indoor

Maximum:D.B/W.B

Maximum:D.B/W.B Maximum:D.B

Maximum:D.B Maximum:D.B

Minimum:D.B/W.B

Maximum:D.B/W.B Minimum:D.B/W.B

Outdoor

Indoor

Outdoor

Heating

32oC/23oC

24oC/18oC

-7oC/-8oC

43oC/26oC 18oC

27oC 15oC

18oC/14oC

Outdoor

Maximum:D.B/W.B Minimum:D.B/W.B

24oC/18oC

-15oC

(INVERTER)

Cautions

11. In order to protect the units,please turn off the A/C first,and at least 30 seconds

later,cutting off the power.

STRICT ENFORCEMENT

Safety Instruction

Installation

WARNING

Please read the following Safety Instructions carefully prior to use.

The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.

lnstallation in a inadequate place may cause accidents. Do not install in the following place.

Connect the earth cable.

earthing

Do not install in the place where there is any possibility of inflammable gas leakage around the unit.

Do not get the unit exposed to vapor or oil steam.

Check proper installation of the drainage securely

PROHIBITION PROHIBITION

CAUTION

Cautions

WARNING

When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.

OFF

Use an exclusive power source with a circuit breaker

ENFORCEMENT

Connect power supply cord to the outlet completely

Use the proper voltage

Do not use power supply cord in a bundle.

Take care not to damage

the power supply cord.

Do not use power supply cord

extended or connected in halfway

STRICT

ENFORCEMENT

STRICT

ENFORCEMENT

PROHIBITION

Do not start or stop the operation by disconnecting the power supply cord and so on.

Do not channel the air flow directly at people, especially at infants or the aged.

Do not try to repair or reconstruct by yourself.

Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.

CAUTION

Take fresh air occasionally especially when gas appliance is running at the same time.

PROHIBITION

STRICT

ENFORCEMENT

Do not operate the switch with wet hand.

PROHIBITION

Do not install the unit near a fireplace or other heating apparatus.

Check good condition of the installation stand

Do not pour water onto the unit for cleaning

PROHIBITION

Do not place animals or plants in the direct path of the air flow

Do not place any objects on or climb on the unit.

Do not place flower vase or water containers on the top of the unit.

Do not insert objects into the air inlet or outlet.

PROHIBITION

Cautions

Indoor unit

OUTLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

INLET

HSU-12HB03/R2(DB)

HSU-22H03/R2(DB)

Inlet grille

Air filter

Vertical flap

Power indicator

Timer mode indicator

Operation mode indicator

Remote signal receiver

Emergency switch(manual)

Test running switch(manual)

Use remote controller to adjust up and down air flow. (Don't adjust it manually.)

Lights up when unit starts.

Lights up when Timer operation is selected.

Lights up during compressor running.

A beeping sound is generated when a signal from remote controller is received.

Used when remote controller is lost or defective. Unit will run temporarily.

Used only for test running in cooling when room temp. is below 16oC. Don't use it in normal operation.

Outdoor unit

HSU-12H03/R2(DB)

HSU-09H03/R2(DB)

HSU-18H03/R2(DB)

Par ts and Functions

Actual inlet grille may vary from the one shown in the manual according to the product purchased

Par ts and Functions

16. SIGNAL SENDING display

17. POWER/SOFT display

18. Left/right air flow display

19. TEMP display Remote controller: to display the TEMP. setting.

20. TIMER OFF display

21. CLOCK display

22. FAN button Used to select fan speed: LOW,MED, HI, AUTO

23. ON/OFF button Used for unit start and stop.

24. SLEEP button Used to select sleep mode.

25. SET button Used to confirm timer and clock settings.

26. POWER/SOFT button

27. LOCK Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition display appears. Press it once again, lock will be canceled and lock condition display disappears.

28. LIGHT button Colorful display bar of the controlling indoor machine is on and extinguished.

29. CODE Used to select CODE A or B with a press,A or B will be displayed on LCD. Please select A without special explanation.

1. SWING button Used to select up or down air sending direction.

2. HOUR button Used to set clock and timer setting.

3. MODE button Used to select operation mode. AUTO, COOL,DRY, FAN,HEAT.

4. HEALTH button Used to set healthy operation.

5. CLOCK button Used to set correct time.

6. TIMER button Used to select TIMER ON, TIMER OFF, TIMER ON-OFF.

7. RESET When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal

8. HEALTH display

9. SLEEP display

11. LOCK display

12. FAN SPEED display

13. TIMER ON display

14. TEMP button Used to select your desired temperature.

15. Operation mode display

10. SWING UP/DOWN display

NOTE: (1)The following functions and related displays are not available and (2) Cooling only unit do not have functions and displays related with heating.

Operation mode AUTO HEAT FANCOOL DRY

Remote controller

LOW HI

MED AUTO

Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key.

Clock Set

When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows:

Remote controller's operation

3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working.

2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly.

1. Press CLOCK button,"AM" or "PM" flashes.

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.

The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well.

Don't throw or knock the remoter controller.

When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated right 2 R-03 (7#) batteries

Remove the battery cover:

Slightly press" "area and push down the cover as illustrated.

Load the battery:

Be sure that the loading is in line with the "+" / "-". request as illustrated on the bottom of the case.

Put on the cover again.

Confirmation indicator:

After pressing power ON/OFF, if no display, reload the batteries.

Note:

Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.

Used two new same-typed batteries when loading. If the remote controller can't run normally during operation, please remove the batteries and

reload several minutes later.

Hint:

Par ts and Functions

Press HEALTH button again, the health function stops.

BRIEF INTRODUCTION TO HEALTH OPERATION

The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.

Note

When the fan motor in the indoor unit does not work, the health lamp lights up, but the anion generator does not release anion.

Health Operation

Remote controller

1. Unit start

Then set up the comfortable working state.

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow).

2. Select operation mode

Press HEALTH button. For one press, is displayed. hence healthy process begins.

When indoor fan motor is running, it has healthy process function. (It's available under any mode)

3. Unit stop

Operation

Auto Operation

Remote controller

About Auto Operation Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature.

1. Unit start

Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as follows:

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

Then Select Auto operation

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

3.Fan speed selection

4.Unit stop

Air conditioner is running under displayed fan speed

When FAN is set to AUTO, the air conditioner

automatically adjusts the fan speed according to room

temperature.

Press ON/OFF button, the unit stops.

Operation

Cool Operation

Remote controller

1. Unit start

Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as follows:

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

Then Select COOL operation

Press TEMP. button

Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will increase rapidly

Every time the button is pressed, temp.setting decrease 1 C,if kept depressed, it will decrease rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

5.Unit stop

Air conditioner is running under displayed fan speed When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

Press ON/OFF button, the unit stops.

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

Operation

Dry Operation

Remote controller

1. Unit start

Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as follows:

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

Then Select DRY operation

Press TEMP. button

Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will increase rapidly

ver y time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will decrease

rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

5.Unit stop

Press ON/OFF button, the unit stops.

COOL operation starts when room temp.is higher than temp.setting.

On reaching temp.setting +2oC unit will run in mild DRY mode.

Ultra-low air flow

Temp.setting+2oC Temp.setting

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

Air conditioner is running under displayed fan speed. In D

RY mode, when room temperature becomes

lower than tem

p.setting+2oC,unit will run inter mittently

at L

OW speed regardless of FAN setting.

Operation

Fan Operation

Remote controller

1. Unit start

Link with electronic power. Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as follows:

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

Then Select FAN operation

3.Fan speed selection

4.Unit stop

About FAN operation

In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled. In FAN mode,SLEEP operation is not available.

Press ON/OFF button, the unit stops.

AUTO

LOW

MED

COOL DRY FAN HEAT

Operation

Heat Operation

Remote controller

1. Unit start

Link with electronic power.

Press ON/OFF on the remote controller, unit starts. The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as follows:

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

Then Select HEAT operation

Press TEMP. button

Every time the button is pressed, temp.setting increase 1 C,if kept depressed, it will increase rapidly.

Ever y time the button is pressed, temp.setting decrease 1 C,if kept depressed, it will decrease rapidly.

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function.

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

Operation

(5)Air flow direction adjustment

After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig.

COOL

HEAT

COOL

HEAT

About 10

About 60

About 10

About 45

About 60

better set a temp. difference of 3-5oC between indoor and outdoor temp. in COOL mode.

Hints

As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more

helpful for a better air circulation.

As warm air flows upward in HEAT mode, adjusting air flow downward will be much more

helpful for a better air circulation.

Be careful not to catch a cold when cold air blows downward.

It is harmful to your health in summer to go frequently in and out of places where temp.

difference is above 7oC. Temp. difference of 3-5oC will remove your fatigue.

More than this, unit's load can be reduced and power consumption cut down as well. So, you'd

(6)Unit stop

Press ON/OFF button.

Cautions:

Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit.

It is advisable not to keep vertical flap at

downward position for a long time in COOL

or DRY mode, otherwise, condensate

water might occur.

Cautions:

When humidity is high, condensate water

might occur at air outlet if all horizontal

louvers are adjusted to left or right.

Move the horizontal blade by a knob on air

conditioner to adjust left and right direction

referring to Fig.

Left and right air flow adjustment (manual)

Press SWING button, vertical flap will move within

the range shown in the Fig. Press SWING button

stop it at a fixed position.

Up and down (Use remote controller)

Operation

Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. Operation Mode

1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will become 1OC higher than temp. setting. After another 1 hours, temp. rises by 1OC further. The unit will run for further 6 hours then stops. Temp. is higher than temp. setting so that room temperature won't be too Iow for your sleep.

Remote Controller

SLEEP operation starts SLEEP operation stops

SLEEP operation starts

SLEEP operation stops

Approx.6hrs

1 hr

3 hrs

Rises 1OC

Temp.setting

Unit stop

In COOL, DRY mode

In HEAT mode

Decreases 2OC

1 hr

Sleep Operation

In HEAT mode 1 hours after SLEEP mode starts, temp will become 2 OC lower than temp. setting. After another 1 hours, temp decrease by 2 OC further. After more another 3 hours, temp. rises by 1OC further. The unit will run for further 3 hours then stops. Temp. is lower than temp. setting so that room temperature won't be too high for your sleep.

In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode.

4. In FAN mode It has no SLEEP function.

Note

The sleeping hours lasts 8 hours and couldn't be adjusted. When timing on function is set, the sleeping function can't be set up After the sleeping function is set up, if user resets timing on function, the sleeping function will be cancelled; the machine will be in the state of timing-on. If the sleeping function and timing-on function are set up at the same time, no matter which one is operated earlier, the machine will be off automatically, and the other function will also be cancelled.

Operation

Remote Controller

Timer On/Off Operation

Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time,just press SET button after mode selecting if time setting is the same as previous one.

Set clock correctly before starting TIMER operation.

1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD.

2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:

BLANK

TIMER ON TIMER OFF TIMER ON-OFF

Then select your desired TIMER mode (TIMER ON or

TIMER OFF). " "or " "will flash.

3.Time setting Press HOUR button.

Every time the button is pressed, time setting increases 1 min, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases 1 min, if kept depressed, it will decrease rapidly. It can be adjusted within 24 hours.

4.Confirming your setting

After setting correct time, press SET button to confirm " "or" "on the remote controller stops flashing. Time displayed: Unit starts or stops at x hour x min. (TIMER ON or TIMER OFF).

5.Cancel TIMER mode

Just press TIMER button several times until TIMER mode disappears.

Operation

Remote Controller

Timer On-Off Operation

Just press TIMER button several times until TIMER mode disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved.

Set clock correctly before starting TIMER operation.

1. After unit starts, select your desired operation mode

Operation mode will be displayed on LCD.

2. Timer mode selection

Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:

BLANK

TIMER ON TIMER OFF TIMER ON-OFF

Then select your desired TIMER mode (TIMER ON - OFF). " "will flash.

3.Time setting

Press HOUR button. Every time the button is pressed, time setting increases 1 min, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases 1 min, if kept depressed, it will decrease rapidlly. It can be adjusted within 24 hours.

4.Timer confirming for TIMER ON

After setting correct time, press TIMER button to confirm " " on the remote controller stops flashing. " " starts flashing. Time displayed: Unit starts or stops at x hour x min.

5.Time setting for TIMER OFF

6.Time confirming for TIMER OFF

To cancel TIMER mode

Just press HOUR button ,follow the same procedure in "Time setting for TIMER ON"

After time setting,press SET button to confirm. " " on the remote controller stops blinking. Time displayed:Unit stops at x hour x min.

Operation

POWER/SOFT Operation

POWER

POWER Operation

SOFT Operation

When you need rapid heating or cooling, you can use this funciton.

You can use this function when silence is needed for rest or reading.

Selecting of POWER operation

Press POWER/SOFT button. Every time the button is pressed,display

In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting.

Press POWER/SOFT button twice ,POWER/SOFT disappears.

In SOFT operation mode, fan speed automatically takes"LOW"

changes as follows:

Stop the display at

SOFT

BLANK

POWER

Press POWER/SOFT button. Every time the button is pressed,display changes as follows:

Stop the display at

SOFT

BLANK

In POWER operation status:

Selecting of SOFT operation

To cancel POWER operation

Press P

OWER/SOFT button once ,POWER/SOFT disappears.

To cancel SOFT operation

Hints: Du

ring POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm.

Operation

When the remote controller is manipulated, it gets the system back to the normal operation mode.

Emergency and Test Operation

When machine is running in emergency, the set value of temperature and wind speed couldn't be altered; meanwhile, it can't operate for dehumidifying or under timing mode.

Emergency operation:

Use this operation only when the remote controller is defective or lost.

When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation.

In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature.

Test operation:

Test operation switch is the same as emergency switch.

Use this switch in the test operation when the room temperature is below 16OC, do not use it in the normal operation.

Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi".

Removal of the restriction of emergency or test operation

Press the emergency operation switch once more, or manipulate through the remote controller; the "Pi" sound, the emergency or test operation is terminated.

Pi Pi

Operation

For Smart Use of The Air Conditioner

Setting of proper room temperature

Proper temperature

During cooling operation, prevent the penetration of direct sunlight with curtain or blind.

Close doors and windows during operation

If the unit is not to be used for a long time, turn off the power supply main switch.

OFF

Use the timer effectively

Use the louvers effectively

Do not block the air inlet or outlet

Maintenance

For Smart Use of The Air Conditioner

WARNING

Air Filter cleaning

Open the inlet grille by pulling it upward.

Remove the filter.

Clean the filter.

Attach the filter.

Close the inlet grille.

Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward.

Use a vacuum cleaner to remove dust, or wash the filter with water.After washing, dry the filter completely in the shade.

Once every two weeks

Attach the filter correctly so that the "FRONT" indication is facing to the front.Make sure that the filter is completely fixed behind the stopper.If the right and left filters are not attached correctly, that may cause defects.

Remote Controller

Do not use the following for cleaning

Do not use water, wipe the controller with a dry cloth.Do not use glass cleaner or chemical cloth.

Gasoline,benzine, thinner or cleanser may damage the coating of the unit.

Hot water over 40OC(104OF) may cause discoloring or deformation.

Wipe the air conditioner by using a soft and dry cloth.For serious stains,use a neutral detergent diluted with water.Wring the water out of the cloth before wiping.then wipe off the detergent completely.

Indoor Body

Before maintenance,be sure to turn off the system and the circuit breaker.

Air Filter

Maintenance

Replacement of Air Purifying Filter

1.Open the lnlet Grille

2.Detach the standard air filter

3.Detach the Air Purifying Filter

4.Attach new Air Purifying Filter

5.Attach the standard air filter as its front side faces to the front

Operating without standard air filter may cause troubles with the machine.

6.Close the Inlet Grille

NOTE:

Close the Grille surely

Open the inlet grille by pushing each ends of the inlet grille upward.(use thumbs to push up)

Slide the knob slightly upward to release the filter, then withdraw it.

Attaching each of the Air Purifying Filter to the indoor unit as its white side faces to the front .

Please replace the air Purifying Filter when color of the filter become same levle of sample attached in the indoor unit.

Replace the old filter with new one into the frame.

Please replace the air Purifying Filter in 3-6 months as standard.

Stuffed filter are not usable even washing.Please purchase new one at sales shop.

Maintenance

To Keep Your Air conditioner in Good Condition after Season.

Operate in cooling mode for 2-3 hours.

Put off the power supply cord.

Take out the batteries from the wireless remote controller.

Cleaning the body.

To prevent breeding mold or bad smell, be sure to operate at the designated temperature or 30OC,cooling mode and High speed fan mode for 2-3 hours.

Maintenance

Before Setting in High season

Cleaning the standard air filter.

Connecting the earthing cable.

Do not block the air inlet or outlet.

Plug-in

Caution

After brush away dust at the plug, insert the plug of the power supply cord into the outlet completely.In case of suing exclusive circuit breaker,switch on the circuit breaker.

NO WET HAND

EARTHING

Operation without filter may cause troubles.Be sure to attach both right and left filters prior to the operation. Each of them are of different shapes.

Incomplete earthing may cause an electric shock.

Maintenance

Is the air filter dirty? Normally it should be cleaned every 15 days. Are there any obstacles before inlet and outlet? Is temperature set correctly? Are there some doors or windows left open? Is there any direct sunlight through the window during the cooling operation?(Use curtain) Are there too much heat sources or too many people in the room during cooling operation?

Cause or check points

Phenomenon

The system does not restart immediately.

Noise is heard:

Smells are generated.

Mist or steam are blown out.

Does not work at all.

Multiple check

Normal

Performance

inspection

Poor cooling

fore asking for ser vice, check the following first.

When unit is stopped, it won't restart immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner.

During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable. (This noise is generated by refrigerant flowing in the system.) During unit operation, a cracking noise may be heard. This noise is generated by the casing expanding or shrinking because of temperature changes. Should there be a big noise from air flow in unit operation, air filter may be too dirty.

This is because the system circulates smells from the interior air such as the smell of furniture, cigarettes.

During COOL or DRY operation, indoor unit may blow out mist. This is due to the sudden cooling of indoor air.

Is power plug inserted? Is there a power failure? Is fuse blown out?

Trouble shooting

Antes de eliminar un aire acondicionado que se ha dejado de utilizar, verificar que está inoperativo y seguro. Desenchufar el aire acondicionado con el fin de evitar el riesgo de que quede atrapado algún niño.

Hay que señalar que el sistema de aire acondicionado contiene refrigerantes, que requieren una eliminación especializada en vertederos. Los materiales valiosos contenidos en un aire acondicionado pueden reciclarse. Ponerse en contacto con el centro local de eliminación de residuos para desechar adecuadamente el aire acondicionado viejo y ponerse en contacto con el proveedor o la autoridad local en caso de duda. Verificar que los conductos del aire acondicionado no están dañados antes de que éste sea recogido por el centro de eliminación de residuos correspondiente y contribuir a la concienciación medioambiental insistiendo en un método de eliminación apropiado contra la contaminación.

Eliminación del aire acondicionado viejo

Todos los materiales de embalaje utilizados en el embalaje de su aire acondicionado nuevo pueden eliminarse sin peligro para el medio ambiente.

La caja de cartón puede romperse o cortarse en trozos más pequeños y enviarse a un servicio de reciclaje de papel. La bolsa del envoltorio está formada de polietileno y bloques de espuma de polietileno.

Todos estos materiales valiosos pueden llevarse a un centro de recogida de residuos y volver a utilizarse después de un reciclaje adecuado.

Consultar a las autoridades locales el nombre y la dirección de los centros de recogida de materiales residuales y los servicios de reciclaje de papel más cercanos al domicilio.

Eliminación del embalaje del aire acondicionado nuevo

Antes de poner en marcha el aire acondicionado, leer detenidamente la información que aparece en la Guía del Usuario. La Guía del Usuario contiene observaciones muy importantes en relación con el montaje, la utilización y el mantenimiento del aire acondicionado.

El fabricante no acepta ninguna responsabilidad por los daños que puedan surgir debido al incumplimiento de la siguiente instrucción.

Instrucciones de seguridad y advertencias

Los aires acondicionados dañados no deben ponerse en marcha. En caso de duda, consultar al proveedor.

La utilización del aire acondicionado debe

efectuarse cumpliendo estrictamente las instrucciones correspondientes señaladas en la Guía del Usuario.

La instalación debe ser efectuada por profesionales; no instalar la unidad por propia cuenta y riesgo.

Por razones de seguridad, el aire

acondicionado debe disponer de una toma de tierra adecuada conforme a las especificaciones.

No olvidar desenchufar el aire acondicionado antes de abrir la rejilla de entrada. No desenchufar jamás el aire acondicionado tirando del cable de alimentación. Sujetar siempre con firmeza el enchufe y tirar de él recto en relación con la toma.

Todas las reparaciones eléctricas deben ser efectuadas por electricistas cualificados. Las reparaciones inadecuadas pueden constituir una fuente importante de peligro para el usuario del aire acondicionado.

Precauciones

No dañar ninguna pieza del aire acondicionado que lleve refrigerante ni perforando ni agujereando los tubos del aire acondicionado con elementos afilados o puntiagudos, ni aplastando ni retorciendo ningún tubo, ni descascarillando los recubrimientos de las superficies. Si se produce una fuga de refrigerante y entra en contacto con los ojos, puede provocar graves lesiones oculares.

Refrigeración

Interior

Máximo:D.B/W.B

Máximo:D.B/W.B Mínimo:D.B

Máximo:D.B Mínimo:D.B

Mínimo:D.B/W.B

Máximo:D.B/W.B Mínimo:D.B/W.B

Exterior

Interior

Exterior

Calefacción

32oC/23oC

24oC/18oC

-7oC

43oC/26oC 18oC

27oC 15oC

18oC/14oC

Exterior

(INVERTER)

Máximo:D.B/W.B Mínimo:D.B/W.B

24oC/18oC

-15oC

1.Rango aplicable de temperatura ambiente:

Especificaciones

La máquina puede adaptarse a las siguientes condiciones

No obstaculizar ni tapar la rejilla de ventilación del aire acondicionado. No poner los dedos ni ningún otro elemento en la entrada/salida ni en la lama giratoria.

No dejar que los niños jueguen con el aire acondicionado. En ningún caso se debe permitir a los niños que se sienten sobre la unidad exterior.

El circuito de refrigeración es a prueba de

fugas.

Precauciones

3. Si el fusible de la unidad interior de la placa PC está roto, cambiarlo por uno del tipo T

3.15A /250V. Si el fusible de la unidad exterior está roto, cambiarlo por uno del tipo T.25A/250V.

7. El electrodoméstico no está diseñado para ser utilizado por menores o personas discapacitadas sin supervisión de un adulto

8. Debe controlarse a los menores para que no jueguen con el aparato de aire acondicionado.

9. Utilizar el enchufe de corriente adecuado que se ajuste al cable de alimentación a la red.

10 El enchufe y el cable de red deben cumplir

la legislación local aplicable

4. El método de cableado debe ser conforme

a la norma local sobre cableado.

5. Después de la instalación, se debe poder llegar con facilidad al enchufe de red.

6. La pila agotada debe eliminarse de forma adecuada.

2. Si el cable de alimentación está dañado, debe ser sustituido por el fabricante o su distribuidor autorizado o una persona con cualificación similar.

11. apagar AC antes de cortar la electricidad

para protegerlo,30s después se puede cortar la electricidad.

12. Un triturador se debe incorporar en el cableado fijo. El triturador debe ser del

todo-poste y la distancia entre sus dos

contactos debe ser no menos de 3mm.

+ 65 hidden pages

Haier HSU-12HD03, HSU-09H03/R2(DB), HSU-12H03/R2(DB), HSU-18H03/R2(DB), HSU-22H03/R2(DB) Operatiing Manual

Specifications and Main Features

Frequently Asked Questions

User Manual