Haier HSM12HEKC03, HSM09HEKC03, AS07GS1ERA, AS09GS1ERA, AS12GS1ERA Operation Manual

Please read this operation manual before using the air conditioner.

●

Keep this operation manual for future reference.

SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL

10

2

3

9

11

PARTS AND FUNCTIONS
OPERATION

MAINTENANCE

TROUBLE SHOOTING

CAUTIONS

INDOOR UNIT INSTALLAION

5

Contents

0010535380

AS07GS1ERA
AS09GS1ERA
AS12GS1ERA

2

Outdoor Unit



Loading of the battery

1
2

3

4









Parts and Functions

Indoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Remote controller

Remove the battery cover;

Load the batteries as illustrated.

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

is in line with th

e" + "/"-";

Load the battery,then put on the cover again.

Clock set

Press CLOCK button, "AM" or "PM" flashes.

Press or to set correct time. Each press

change quickly.

After time setting is confirmed,press SET,

"AM "and "PM" stop flashing,while clock starts working.

or decrease 1min. If the

button is kept pressed,time will

will increase

The distance between the signal transmission head and the rece­iver hole should be within 7m without any obstacle as well.

When electronic-sta rted type fluorescent lamp or change- over

wireless telephone is installed in the

ver is apt to be disturbed in receiving

the signals,

so the distance to the indoor unit should be shorter.

type fluorescent lamp or
room, the recei

Note:

Full display or unclear display during operation indicates the

ries have been used up.

Please change batteries.

If the remote controller can't run normally during operation, please

reload several minutes later.

batte

remove the batteries and

Please be subject to the actual produce purchased the
above picture is just from your reference

Please be subject to the actual produce purchased the
above picture is just from your reference

Air Purifying Filter

(inside)

Inlet

1

Inlet grille

2

Outlet

3

(adjust left and

Vertical blade

right air flow)

4

Display board

Horizontal flap

(adjust up and down air flow.

Don't adjust it manually)

Emergency

Switch

6

7

8

5

1

2

3

4

5

6

7

8

1. Mode display

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

LO MED HIAUTO

1

2

3

5

6

7
8
9

10

4

ON/OFF

FAN

MODE

SWING

TIMER

CL

OCK

SET

SLEEP

LOCK

RE

SET

11

12

14

15

16

17

13

18

19

20

21

22

POWER/SOFT

LIGHT

23

P

OWER

SOFT

BLANK

9. CLOCK display

10.TEMP display

11. POWER ON/OFF button

12. MODE button

13. FAN button

14. HOUR button

15. SWING button

16. SLEEP button

17. LOCK button
Used to lock buttons and LCD
display.

18. TEMP.SETTIN button

19. SET / LIGHT button

20. TIMER button

21. CLOCK button
Used to set correct time.

22. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this
button to reset the remote
controller normal.

23. HOUR / POWER/SOFT button
Used to set clock and timer setting.
Every time the button is pressed,
display changes as follows:

Operation mode

AUTO

FAN

COOL DRY

Remote controller

HEAT

LOCK

RESET

TIMER

CLOCK

SET

SLEEP

POWER/SOFT

LIGHT

4

Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.

3

Operation

Air Flow Direction Adjustment

AUTO COOL DRY

FANHEAT

2.Select operation mode

Press FAN button. For each press, fan speed

follows:

Press MODE button. For each press, operation mode
changes as follows:

Remote controller:

Remote controller:

Press

button

Every time the button is pressed, temp.setting
increase 1

o

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

o

C,if kept depressed, it will

decrease rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.

1. Unit start

Press ON/OFF on the remote controller, unit starts.



Base Operation

Remote controller

Vertical flap

Pos.1 blank

Pos.2

Pos.3

Pos.4

(Auto swing)

1.Status display of air flow

When restart after remote turning off, the remote

memorize the previous

Move the vertical blade by a knob on air

to adjust left and right direction referring to Fig.

2.Left and right air flow adjustment

(manual)

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur

adjusted to left or

It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY

otherwise, condensate water might occur.

conditioner

Emergency operation and test operation

at air outlet if all vertical louvers are

right.

mode ,

controller will automatically

Note:

set swing position.

changes as

'

Operation

Mode

AUTO

Remote

Controller

Note

COOL

DRY

HEAT

FAN

In DRY mode , when room temperature becomes
lower than temp.setting+2

o

C, unit will run

intermittently at LOW speed regardless of FAN

Under the mode of auto operation, air conditioner
will automatically select Cool or Heat operation

according to room temperature

to AUTO the air conditioner

automatically adjusts

temperature.

When FAN is set

the fan speed according to room

In FAN operation mode , the unit will not operate in
COOL or

HEAT mode

but only in

FAN mode ,

AUTO is not available in

FAN mode.

And temp.

setting is disabled. In FAN mode, sleep operation

setting.

is not available.

AUTO LO MED HI

ON/OFF

FAN

MODE

LOCK

RESET













SWING

TIMER

CLOCK

SET

SLEEP

POWER/SOFT

LIGHT

test operation

switch

Pi

Pi

Emergency Operation:

Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:

Room
temperature

Designated
temperature

Timer
mode

Fan

speed

Operation

mode

Above 23oC

Below 23

o

C 23oC

26

o

C

No

AUTO

AUTO

COOL

HEAT

No

Pi

emergency

operation switch

It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.

temperature is below 16

o

C, do not use it in the

Test operation:

Use this switch in the test operation when the room

normal operation.

your finger from the switch: the cooling

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice,

release

Test ope ration switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor

unit will run in high speed.

In HEAT mode, warm air will blow out after a short
period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.

Operation

Sleep Operation

Use of SLEEP function

Operation Mode

1. In COOL,DRY mode

SLEEP operation starts SLEEP operation stops

SLEEP
operation starts

SLEEP
operation stops

Approx.6hrs

1 hr

1 hr

1 hr

3 hrs

3 hrs

Rises 1OC

Rises 1

O

C

Rises 1OC

Temp.setting

Temp.setting

Unit stop

Unit stop

In COOL, DRY mode

In HEAT mode

Decreases 2OC

Decreases 2

O

C

1 hr

2.

3.

In HEAT mode

In AUTO mode

4. In FAN mode

It has no SLEEP function.

POWER/SOFT Operation

Before going to bed,you can simply press the SLEEP
button and unit will operate in SLEEP mode and bring
you a sound sleep.

After the unit starts,set the operation status,
then press SLEEP button before which the
clock must be adjusted and time being set.

1 hours after SLEEP mode starts,temp.will become
1 higher than temp.setting.After another 1 hours,
temp.rises by 1 futher.The unit will run for further
6 hours then stops Temp. is higher than temp.
setting so that room temperature won’t be too low
for your sleep.

1 hours after SLEEP mode starts,temp will
become 2 lower than temp.setting.After
another 1 hours,temp decrease by 2
futher.After more another 3hours,temp.rises
by 1 futher.The unit will run for further 3
hours then stops.Temp.is lower than temp.
setting so that room temperature won’t be
too high for your sleep.

The unit operaters in corresponding sleep mode
adapted to the automatically selected operation
mode.

O

C

O

C

O

C

O

C

O

C

4

Power Failure Resume Function

When TIMER function is set , the quiet sleeping
function can't be set up. After the sleeping function
is set up, if user resets TIMER function, the sleeping
function will be cancelled; the machine will be in the
state of timing-on, if the two modes are set up at the
same time, either of their operation time is ended
first, the unit will stop automatically, and the other
mode will be cancelled.

When quiet sleeping function is set to 8 hours

,

the quiet sleeping time can not be adjusted.

5.

1. If the unit is started for the first time, the compressor
will not start running unless 3 minutes have elapsed.
When the power resumes after power failure, the unit will
run automatically, and 3 minutes later the compressor
starts running.

2. Note to the power failure resume:
press the sleep button ten times in five seconds and enter
this function after hearing four sounds. And press the sleep
button ten times within five seconds and leave this function
after hearing two sounds.

(1)

POWER Operation

(2)

SOFT Operation

When you need rapid heating or cooling, you can use this function.
In COOL mode, fan speed automatically takes high speed of
AUTO fan mode. In HEAT mode, fan speed automatically takes
medium speed of AUTO fan mode.

You can use this function when silence is needed for rest or reading.
In SOFT operation mode, fan speed

automatically takes low speed

of AUTO fan mode.

Note˖
During POWER operation, in rapid HEAT or COOL modethe room

will show uniform temperature distribution. Long period
SOFT operation will cause effect of not too cool or not too warm.

To cancel POWER or SOFT operation
Press POWER/SOFT button again, POWER or SOFT

disappears.