Haier HLH26BBTV User Manual

IMPORTANT SAFETY INSTRUCTIONS

Read all of the instructions before using this appliance. When using this

appliance, always exercise basic safety precautions, including the following:

1)Save these Instructions ---the safety and operating instructions should be
retained for future reference.

2)All warning on the appliance and in the operating instructions should be followed.

3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use only dry cloth for cleaning.

4)Attachments ---do not use attachments not recommended by the manufacturer
as they may cause hazards.

5)Water and moisture -- do not place this product near water, for example, near a
bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.

6)Accessories ---do not place this unit on an unstable cart, stand, tripod, bracket,
or table. Use only with a cart, stand, tripod, bracket, or table recommend by the
manufacture, or sold with the unit.

7)Ventilation ---Slots and openings in the cabinets and the back or bottom are
provided for ventilation. These openings must not be blocked. In a built in
installation such a bookcase or rack do not install product unless proper ventilation
is provided.

8)Power Source ---this TV should be operated only from the type of power source
indicated on the rating label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company.

9)Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. To prevent electric shock, ensure
the grounding pin on the AC cord power plug is securely connected.

10)Power cord protection ---Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords or plugs, convenience receptacle, and the point where
they exit from the appliance.

11)Lighting precaution ---for added protection for this product during a lighting
storm or when it is left unattended for long period of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the
product due to lighting and power line surges.

12)Never push objects of any kind into this product through openings as they may
touch dangerous voltage point or short out parts that could result in a fire or electric
shock. Avoid spilling liquid of any kind on the product.

13)Servicing ---do not attempt to service the product by yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to authorized service personnel.

14)Unplug this unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.

Owner s Manual 3

b.If liquid has been spilled, or objects have been fallen into the unit.
c.If the unit has been exposed to rain or water.
d.If the unit does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions, as
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the unit to its normal
operation.
e.If the unit has been dropped or damaged in any way.
f.When the unit exhibits a distinct change in performance; this indicates a need
for service.

15)Heat --- The product should be situated away heat source such as radiators, heat
registers, stoves, or other products (Including amplifiers) that product heat.

16)Overloading ---Do not overload wall outlets and extension cord as this can result
in a risk of fire or electric shock.

SAVE THESE INSTRUCTIONS

INPUT VOL VOL

MENU

MENU TV/AV

Menu exit

Signal source input option

Down/Up. Sel ct desired option on MENU or tune

e

to the desired channel.

VOLUME Buttons

MENU Button

P- P+ V- V+ POWER

Power On/Off Button

Power Standby Indicator
illuminates red in standby mode,illuminates blue when
the display is turned on

Remote Control Sensor

Power On/Off

0

VGA Input/Audio input

Audio/Video Input 2
Connect audio/video
output from an external
device to these jacks

S-Video Input

DVI Input/Audio input
connect your cable/PC
through the input

Earphone port

VGA IN

AC IN

VGA

AUDIO

COMPONENT IN

Pr/Cr Pb/Cb Y L-AUDIO-R

DVD/DTV Input
Connect a component video/audio
device to these jacks

Power Cord Socket
This TV receiver operates on AC power. The
voltage is indicated on the specifications page.
Never attempt to operate the TV on DC power

DVI IN

DVI

AV OUT

L-AUDIO-R

VIDEO AUDIO

AV IN

L-AUDIO-R

S-VIDEO VIDEO

ANTIN

Audio/Video Input 1
Connect audio/video
output from an external
device to these jacks

External audio/
video output

Antenna Input

Connect cable or
antenna signals to
the TV, either direc­tly or through your
cable box.

When using the remote control. Aim it towards the remote sensor on the TV.

Function introduction

Freezes the currently-viewed picture.

FREEZE

SLEEP

Press this key to set sleeptimer.

PC

Select PC source

AUTO

Auto adjust for PC

FAVORITE

no available

MTS/SAP

no available

MENU

Brings up the main menu to the screen or exit.

CHANNEL UP/DOWN

Selects available channels found with

channel Scan.

P.STD

Display the picture appropriate for

the program's character.

S.STD

Display the sound appropriate for

the program's character.

LOCK

CALENDAR

INPUT

Display all the source input mode.

MUTE

Switches the sound on or off

POWER

PC FREEZE

INPUT

POWER

Turns your TV or any other programmed

AUTO

SLEEP

MUTE

DISPLAY

equipment on or off, depending on mode.

Information display

Display of current signal information

Digits

Program direct option(when edit program,
every press can set different sign by turns among
the digits and sign on top of them)

-

Q.VIEW

Q.VIEW

MTS/SAP

VOL-

P.STD

S.STD

LOCK

CALENDAR

CH+

MENU

CH-

GUIDE

EXIT

VOL+

CC

AVC

RATING

ARC

DNR

. Press to enter the Lock Set menu

Switch the current channel to the
last channel you have viewed.

EXIT

Clears all on-screen displays and returns to
TV viewing from any menu.

VOLUME UP/DOWN

Increases/decreases the sound level.

CC(Closed Caption)

RATING
set the parental control.

ARC

Changes the aspect ratio.

AVC

Automatic Volume Control

DNR

Digital noise reduction

GUIDE no available

Shows program schedule.

Installing Batteries

Open the battery compartment cover on the back side and install

the batteries matching correct polarity (+ with +, - with -).

Install two 1.5V AA batteries. Don`t mix old or used batteries with

new ones.Replace cover.

1

2

3

PC

INPUT POWER

VIDEO

DISPLAY

MUTE

DVI

AUTO

MENU

DNR

EXIT

AVC

ENTER

P.STD

VOL+

CALENDAR

LOCK

VOL-

S.STD

SAVING

ARC

CC

/

SURROUND

FREEZE

SLEEP

RATING

* In this manual, the OSD (On Screen Display) may be different from your `s, because it is just
an example to help you with the operation.

TV

TV

TV

Turning on the TV just after installation.

1. Connect power cord correctly.

2. Press the switch button on back of the TV. At this moment, the TV is switched to standby mode.

Press the POWER button on the remote control or on the TV and then the TV will turn on.

Turning on the TV

1. If the TV was turned off with the button on the TV

Press the switch button on the TV to turn the TV on.

switch

2. If the TV was turned off with the remote control and then the ON/OFF switch on the back of the TV.

Press the switch button on the back of TV and then press the POWER button on the remote control to turn
the TV on.

NOTE
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

Choose the Menu Language

When you start using your set for the first time, you must select the Menu Language which will be used for displaying

menus and indications.

1 Press MENU and then use VOL+/- button to select the

FUN. Menu.

2 Press CH+/-button to select Menu Language.

3 Select a particular Menu Language by pressing VOL+/- button

repeatedly.

4 When you are satisfied with your choice, press the EXIT button to

return to normal viewing.

Menu Language English

OSD Timeout 15seconds

Menu Background Translucent

Calendar

Auto Off Off

BlueScreen Off

Close Caption Off

Parental

A

B
C

Choose the Input Source

- Change the picture source so that you can watch your TV, cable TV, VCR, DVD, or any other devices that are
connected to your TV.

1. Press INPUT button on the remote controller, the Scoure menu will appear on the screen.

2. Press CH+/-button for option and then press VOL+/- button to confirm.

Source

TV
AV1
AV2
YPbPr/YCbCr
VGA
DVI

Basic Function

Basic Function

Operation Menu

1.Press MENU button to open the main menu. Press VOL+/- button to select PIC., SOU., ADJ., SYS. , FUN. or TIME menu.

2.Press CH+/- button to select submenu, and press VOL+/- button to increase/decrease the value or select the setup.

3.Press MENU to return to the main menu.

4.The setup time in display will disappear automatically without any operation when the latest preset time expiries. MENU
display time can be set to 5,10,15,20,25,30 and 40 seconds.

5.Press EXIT button to exit any menu if MENU is on display.

Sound Mode

Press S.STD button on the remote controller for menu display, and then use CH+/- button to select
the desired mode, press VOL+/- to confirm.

(This feature can also be changed from the sound menu function screen)

Personal:

Standard:

Music:

Theater:

A spare setting that can be adjusted to personal tastes.

Normal sound with moderate bass and treble setting.

Adjust the sound to best suit music programs

Enables extra bass and treble to enhance the movie experience.

.

Picture Mode

Press P.STD button on the remote controller for menu display, and then use CH+/- button to select
the desired mode, press VOL+/- to confirm.

(This change can also be made from Picture menu adjustment screen)

Standard:

Vivid:

Mild:

Custom:

normal mode.

mode of watching the movement of picture.

the effect of the picture is soft.

picture effect which you favorite.

Sleep Timer

SOU.Mode

Music

Standard

Theater

Personal

PIC.Mode

Vivid

Standard

Mild

Custom

Every press of SLEEP button, the timer will be set in the following sequence:

Sleep 0Min Sleep 5Min Sleep 15Min Sleep 30Min Sleep 60Min Sleep 90Min Sleep 120Min Sleep 0Min

If remaining time of set timer is to be displayed, press the SLEEP button once.

System Menu

This TV set has three methods to set channels, which are respectively Automatic search, manual search fine tune.
In this section, how to use the remote control to set channel is explained. You can also use

buttons on the TV set to set channel.

Channel Type

1 Press MENU button and then use VOL+/- button to select the SYS. Menu.
2 Press CH+/- buttons to select "Channel Type" item.

3 Press VOL+ button to select CATV or Air item.

When Air is selected, the TV will detect antenna signals and will search
for antenna TV (NTSC and ATSC) channels available in your local area.

CATV

When is selected, the TV will detect cable company supplied

signals and will search for cable TV (NTSC,ATSC, QAM modulated)
channels available in your area.
Make sure that registration with your cable TV provider and connection
of equipment are completed.

When Air and are selected, the TV will detect the antenna

signals and cable company supplied signals, and search for the
antenna TV and cable TV channels available in your area.

CATV

CATV Type

1 Press MENU button and then use VOL+/- button to select the SYS. Menu.
2 Press CH+/- buttons to select "CATV Type" item.

3 Press VOL+/- button to select STD, IRC or HRC item.

Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type CATV
CATV Type STD
Auto Scan
Prog. Switch

A

B
C

Note : the tuning menu will be
only operated in normal TV mode.

Automatic Scan

1 Press MENU button and then use VOL+/- button to select the SYS.Menu.

2 Press CH+/- buttons to select "Auto Scan" item.

3 Press VOL+/- button to ensure automatic search function work.

4 Press MENU button to stop automatic search function.

After the search has finished, all channels now playing
program will be automatically preset in order.

Fine Tune

If the picture or sound are poor, try using the fine tune feature.
Do not use this feature unless reception is poor.

1 Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item.

2 Press VOL-/+ buttons repeatedly to carry out fine tune, till the best

picture and sound are obtained, then loosen the button.

Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type CATV
CATV Type STD
Auto Scan
Prog. Switch

A

B
C

System Menu

Color System

Usually this should be set in the auto position. However if the color displayed
on the screen are incorrect, you can manually select the correct color system.
Press MENU and then VOL+/- button, till the picture menu shown on the
right will display on the screen.

Press CH+/- buttons to select "Color Sys.", then press the VOL-/+ buttons
to select the correct color system. In general, you can set it as "AUTO".

Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type CATV
CATV Type STD
Auto Scan
Prog. Switch

A

B
C

Skip

After the programs are presetting, you can skip some programs so that to select your favorite channels only.

1. Press CH+/- button or Direct-digit choosing button to select a channel directly.

2.Press MENU and then use VOL+/- button to select the SYS. Menu.

3.Press CH+/- buttons to select "Skip" item.

4. press VOL-/+ button to set Skip as On.

5. When you are satisfied with your choice, press MENU button to return to
the previous menu or press EXIT button to return to TV viewing.

If you want to recover the skipped channel

1. Use Direct-digit Choosing button to select the number of the channel to
be recovered.

2. Do the above steps again.

3. Press VOL+/- button to set Skip as Off.

Color Sys. AUTO
Sound Sys. M/N
Fine Tune 49.75MHz
Skip Off
Channel Type CATV
CATV Type STD
Auto Scan
Prog. Switch

A

B
C

Prog.Switch

1 ..Press MENU and then use VOL+/- button to select the SYS. Menu

2. Press CH-/+ button to select Prog.Switch.

3. Press VOL+/- to enter the submenu, and press the digital button to set the desired

channel number,
Press CH+/- button to Current Prog or To Prog item, and VOL+/- to select the position then press the digital button to set the
exchange channel number, press CH+ button to Switch, then press VOL+ button to confirm.

4. When you are satisfied with your choice, press MENU button to return to

the previous menu or press EXIT button to return to TV viewing.

Current Prog 000
To Prog 001
Switch

A

B
C

Picture Quality Adjust

Picture Quality Adjust

Picture Quality Adjust

The TV menu gives you an overview of MENU you can select.

Note: Depending on the input signal, one or more menu items may not be selectable.

1 Press MENU and then use VOL+/- button to select the PIC. Menu.

2 Press CH+/-button to select the desired items.

3 Press VOL+/- button to adjust the setting.

4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press EXIT button to return to TV viewing.

Contrast

This will adjust the intensity of bright parts in the picture but keep
the dark parts unchanged.

Brightness

This will adjust the light output of the complete picture, which will
mainly affect the darker areas of the picture.

Mode Custom

Contrast

Brightness

Color

Hue

Sharpness

DNR Auto

50

50

50

0

50

A

B
C

Color

This will adjust the saturation level of the colors to suit your personal preference.

Hue (selectable in NTSC mode only)

Allows you to select the color mix (Hue) of the picture.

Sharpness

This will adjust the sharpness of fine details in the picture.

DNR (Digital Noise Reduction )

Automatically filters out and reduces the image noise and improves picture
quality when receiving weak video signals.
Select Auto/Off/Weak/Medium /Strong according to the image noise.

Note:

When Custom mode is not selected, the Custom mode can be entered automatically if Contrast, Brightness,

Color, Hue and Sharpness parameters are adjusted.

Sound adjustment

Sound adjustment

Sound Adjust

Sound can be adjusted for any input as follows:

1. Press MENU button and then use VOL+/- button to select the SOU.menu.

2. Press CH+/- button for desired option.

3. After your option is selected, press VOL+/- button to adjust.

4. Repeat step 2 and 3 until desired sound has been achieved when displayed
time for menu setup expires without any operation , MENU disappears from
the picture . If MENU or EXIT button is pressed , MENU in display will disappear
in sequence or immediately respectively.

Volume

This will adjust the sound output level.

Volume 50
Balance 0

SOU.Mode Personal

Treble 50
Bass 70
Surround Off
AVC Off
Woofer Off

A

B
C

Balance

This will adjust the output of the right and left speakers to obtain the best
stereo reproduction for your listening position.

SOU. Mode

This select the modes for sound reproduction dependent on the broadcast signals or signals from external inputs received.
Press CH+/- button to Select SOU.Mode,
press VOL+/- button to select the Music Standard Theater or Personal.

Treble

This will adjust the treble output level.

Bass

This will adjust the bass output level.

Surround

The surround sound feature expands the audio listening field wider and deeper to create exceptional sound quality
from the TV`s speakers.
Press CH+/- button to Select Surround,
press VOL+/- button to set Surround as Off or On

AVC (Automatic Volume Control)

Each broadcasting station has its own signal conditions, and so it is not easy for you to adjust the volume every time the
channel is changed. This feature lets you automatically adjust the volume of the desired channel and reduces the volume
differences between channels and programs, providing a more constant overall level.
This will also reduce the dynamics of sound.
Press CH+/- button to Select AVC,
press VOL+/- button to set AVC as Off or On

Woofer

Woofer is a speaker that complements front speaker`s reproduction capability of low-pitched sound.
Press CH+/- button to Select Woofer,
press VOL+/- button to set Woofer as Off or On

Note:

1. Select Balance to balance right and left sound channels of the TV. The intermediate value is 0. When indication value of
Balance increases toward+50, sound of the right and left speaker becomes stronger and weaker, respectively. When indication
value of Balance decreases toward -50, sound of the right and left speaker becomes weaker and stronger.

2.When Personal mode is not selected, the Personal mode can be entered automatically if Treble or Bass parameters are adjusted.

Adjustment Setup

Adjustment Setup

Adjustment Setup

In VGA and DVI input mode , H Position and V Position can be used to

VGA/DVI:

adjust the picture position.

Display Mode Full Screen

When VGA DVI input mode is set

1. Press MENU button on the remote controller and then use the
VOL+/- to select the ADJ.menu.

Press CH+/- to enter .

2.

3. Press the VOL+ button and then use CH+/- button for desired
adjust parameter option.

4. Press VOL+/-for desired adjust parameter option until satisfactory
value is achieved. When VGA signals are received, the automatic
mode is used for parameter adjustment.

Adjust

RGB

Reset

Auto Sync.

Color Temper Standard

Black Stretch On

A

B
C

Note:

Adjust, RGB and Reset are functional only under VGA and DVI mode, and Auto Sync is functional in VGA mode.

Display Mode

This will adjust the picture ratio.
Under the VGA signal, there are Full Screen , one to one and 4:3
mode for Display mode to select.
Under the AV1or Av2 signal, there are Full Screen, Vertical Zoom,
Half Zoom, Panorama and 4:3 Mode for Display Mode to select.
Under the DVI signal, there are Full Screen and 4:3 Mode for Display
Mode to select.

Adjust
this is opted for adjusting H Position and V Position as well as
relative parameters in VGA and DVI modes.(Phase Adjust is not
available in DVI)

RGB

this is opted for adjustment of the numerical value of red, green and
blue in VGA/DVI mode.

H Size

H Position

V Size

V Position

Phase Adjust

A

B
C

Red

Green

Blue

No selectable

0

0

0

0

0

0

0

0

Reset
this is opted for initialization adjustment of parameters (After the operation,
Complete will be on the right of the option)

Auto sync
this is opted for adjustment of picture location frequency and phase
parameters in VGA mode. (Not available in DVI)
( After the operation, Complete will be on the right of the option.)

Color temperature

This will increase or decrease Warm (red) and Cold (blue) colors to suit
personal preferences.
Select Cold to give the white colors a blue tint, Standard to give the white
colors a neutral tint, Warm to give the white colors a red tint.

A

B
C

Function Setup

Function Setup

Function Setup

It is possible to select Menu Language, OSD translucent, position and screen display of MENU as follows:

1. Press MENU button once, and then use VOL+/- button until the following menu appears on the screen:

2. Press the VOL+ button and then use CH+/- button on the remote controller to enter MENU of system setup.

3. Press CH+/- to select desired option on MENU.

4. Press VOL+/- to adjust selected option.

Menu Language Option

Repeat step 3 and 4 to select English, Francais or Espanol as MENU Menu Language.

OSD Timeout Option

Repeat step 3 and 4 to select menu display time for 5,10,15, 20, 25, 30 or 40 seconds.

Av

Menu Language English

OSD Timeout 15seconds

Menu Background Translucent

Calendar

Auto Off Off

BlueScreen Off

Close Caption Off

Parental

A

B
C

Menu Background Option

Repeat step 3 and 4 to select OSD background between Translucent and Opaque.

Calendar Display and Check

Repeat step 3 and press VOL+/- button to enter calendar menu as follows:

Enter Calendar menu, press VOL+/- and CH+/- button to
adjust or check the date.

Auto Off

Repeat step 3 and 4 to select On/Off. If On is selected, and there is no signal to the TV for 2 minutes , Auto Off will

be on the screen and for 3 minutes the TV will be in standby condition . If Off is selected , and there is no signal to the

TV for 3 minutes without any operation , screen protection will be on the screen .

BlueScreen

Repeat step 3 and 4 to select blue Screen between off or on.

Close Caption

Closed captioning is a process which converts the audio portion of a television program
into written words which then appear as subtitles on the television screen. Closed
captions allow viewers to read the dialogue and narration of television programs.

Using Closed Captions

Captions are the subtitles of the dialogue and narration of television programs.
For prerecorded programs, program dialogue can be arranged into captions in
advance. Its possible to caption a live program by using a process called real-time
captioning, which creates captions instantly. Real-time captioning is normally
done by professional reporters using a machine shorthand system and computer
for translation into English.
Captioning is an effective system for the hearing-impaired, and it can also aid
in teaching Menu Language skills.

1. Press MENU button and then use VOL+/- button to select the Fun. menu.

2. Press CH+/- to select Close Caption.

3. Press the VOL+/- button to select available caption items.
(Off/CC1/CC2/CC3/CC4/TX1/TX2/TX3/TX4/XDS.)

TEXT
The term for the words that appear in a large black frame and almost cover
the entire screen; usually messages provided by the broadcaster.

4. Press EXIT button to return to TV viewing.

(Note: Close Caption is only available in AV and S-Video signal)

Parental

Menu Language English

OSD Timeout 15seconds

Menu Background Translucent

Calendar

Auto Off Off

Blue Screen Off

Close Caption Off

Parental

A

B
C

Parental Control can be used to block specific channels, ratings and
other viewing sources.

The Parental Control Function (V-Chip) is used to block program viewing
based on the ratings sent by the broadcasting station.
The default setting is to allow all programs to be viewed.
It is also possible to block all program viewing for a time period.
To use this function, the following must be done :

1. Set ratings and categories to be blocked.

2. Specify a password

3. Enable the lock

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television
programs and television movies can be blocked by TV Rating and/or
Individual Categories. Movies that have been shown at the theaters or
direct-to-video movies use the Movie Rating System (MPAA) only.

1. Press CH+/- to select Parental.

2. Press the VOL+ button to enter Parental submenu.

The TV is set up with the initial password 0-0-0-0

password is 9-4-4-3

. If the password in the Lock Set menu be changed,

The password here will also change.

and security default

Menu Language English

OSD Timeout 15seconds

Menu Background Translucent

Calendar

Auto Off Off

BlueScreen Off

Close Caption Off

Parental

A

B
C

Parental

Parental Control Off
Unrated Program Block Off

Parental Guild

MPAA Rating

Continue

Parental

Ratings for Movies previously shown in theaters:

Movie Ratings :
NR (Permits all programs)

G (General audience)
PG (Parental guidance suggested)
PG-13 (Parents strongly cautioned)
R (Restricted)

Parental Control Off
Unrated Program Block Off

Parental Guild

MPAA Rating

NC-17 (No one 17 and under admitted)
X (Adult only)
If you set PG-13 : G and PG movies will be available , PG-13, R,
NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

TV-Y (All children)

TV-Y7 (Children 7 years older)
TV-G (General audience)
TV-PG (Parental guidance suggested)
TV-14 (Parents strongly cautioned)

Rating ALL V S L D
TV-Y V
TV-Y 7 V V
TV-G V
TV-P G V V V V V
TV-1 4 V V V V V
TV-M A V V V V

TV-MA (Mature audience only)

TV Rating Children:
ALL (Age) (applies to TV-Y, TV-Y7)
FV (Fantasy Violence) (applies to TV-Y7)

TV Rating General:
ALL (Age) (applies to TV-G, TV-PG, TV-14, TV-MA)
D (Dialogue - sexual dialogue) (applies to TV-PG, TV-14)
L (Language - adult language) (applies to TV-PG, TV-14, TV-MA)
S (Sex - sexual situations) (applies to TV-PG, TV-14, TV-MA)
V (Violence) (applies to TV-PG, TV-14, TV-MA)

Parental

Parental Guild

MPAA Rating

G V
PG V
PG-13 V
R V
NC17 V
X V

Note: If some option is locked, the options of the same level will also be locked and the screen displays Lock .

TV Rating Limit and Movie Rating Limit can only be opted when Parental Control is set to Custom.

(Parental is only available in AV and S-Video signal)

Time Setup

Time Setup

If Off-time or On-time is intended in AV1/S-Video/YPbPr/YCbCr/VGA , follow the instructions as below:

Clock Setting

The clock will only work if the TV set is turned on or in standby.
When the set is disconnect from the power supply or is turned off by
the main power on the rear panel, the clock loses power and will need
to be reset when the power is reconnected.

1 Press MENU button and then VOL+/- button to select the TIME menu.
2 Press CH+/- buttons to select "Clock",press VOL +/- buttons to select hour

or minute position, then press the digital buttons to set the value of hour or minute.

Clock --:--

Off Time --:--

On Time --:--

On Prog 000

Remind Time --:--

Remind Prog. 000

Note:

If Clock is set, time you set for Off Time and On Time will be a point
of tiem. Otherwise, if Clock is not set, time you set for Off Time and
On Time will be a period of time. And it will account time from the time
when you set automatically .

Off/On Time

Using on/off time function, the TV set can automatically turn on to a preset program or shut down in a preset

A

B
C

1 Press CH+/- buttons to select "On Time", press VOL+/-buttons to select hour or minute position; then press the digital

buttons to set the value of hours or minutes.

2 Press CH+/- buttons to select "On Prog", then press the digital buttons to select your desired channel.
3 Repeat step 1-2 to set Off Time .

Indication will appear on the screen 1 minute prior to

Note:

The Sleep Time and Off Time can not be set at simultaneously .
If both time are set , the later setup will be in operation.

Remind Time/Remind Prog.

expiration of the set

Off Time

1 Press MENU and then VOL+/- button to call up the TIME menu on the screen.
2 Press CH+/- buttons to select "Remind Time", then press VOL+/- buttons to select hour or minute position;

then press the digital to set the value of hour or minute.

3 Press CH+/- buttons to move the cursor to "Remind Prog.".

Then press the digital buttons to set the desired channel.

Lock Menu Options

Lock Menu Options

- The TV has the function of security default lock. Password needs to be entered when the program lock mode is to be set.

Lock Setup

Press LOCK button on remote control, Password will appear on the screen. If password is correctly entered, the Lock set menu will be

menu willl be entered. If the password is not correctly entered, you will be required to reenter the password and the cursor will stay

At the first place. Press EXIT to erase the window. If time you set in OSD menu expires after the latest press, MENU

will disappear automatically.

Lock Set

PassWord
Tuning Lock Off

Change Password

The password can be changed. Press CH+/- button and select

Password. Press VOL+/- or ENTER button, the screen will display

Old Pw.----, which will stay on the screen if a wrong password

is entered. If correct password is entered, the screen will

display New Pw.----. Then enter the new password, and the screen will display

Confirm----. If the same password is entered correctly twice, the old password will be changed. If the same password

is not correctly entered twice, the screen will display New Pw.----, then you have to reenter the password.

Preset Prog. Off
Prog. Num 1
Source Lock
Child Lock Off
Max Volume 100
UnLock

Note:

The initial password is 0000, and the security default password is 9443. If Unlock is activated, the password

setup cannot be changed.

Tuning Lock

Press CH+/- to select Tuning Lock and VOL+/- to set On/Off. (To set On, some operation such as search will be
not available. When enter the SYS. menu, Tuner Lock will be on the screen, and the time will be the same with
the main menu if no operation. If you want to operate SYS. menu, you need to enter the Lock menu to set Tuning
Lock Off or operate UnLock.

Preset Prog.

Preset Prog. is opted for setting up start signal resource. Press CH+/- button to select Preset Prog. Press VOL+/-

button, sources can be swapped in TV/AV1/SVideo/AV2/YPbPr/VGA/DVI/Off mode. After setup, the set mode will be

entered if the TV is switched off and on again. entered if the

Prog.Num

Prog. Num is opted for setting up preset channel. Press CH+/- button to select Prog Num. Press VOL+/- button, to select
channel number.(The item is not available except TV signal.)

Source Lock

Source Lock is opted to hinder external input modes, such as AV, S -Video and VGA. Press CH+/- button to select

the option, and press VOL+/- button to display Source Lock menu.

Press CH+/- button to select desired option. Press VOL+/- button to set up the
mode of Source Lock. If some Source Lock is set on, the mode will be entered
and the screen will display blue background with the mute mode activated
and Lock. In lock on mode, when screen is blank, icon Lock will be always
displayed on the screen. If lock mode is to be verified, enter Source Lock sub
menu and set relative mode off or select Unlock mode in the Preset Prog.Menu.

Source Lock

AV1 Off

S-Video Off

AV2 Off

YPbPr/YCbCr Off

VGA Off

DVI Off

Child Lock

Press CH+/- button to select Child Lock. Press VOL+/- button to set On or Off mode. If lock on mode is set,

Child Lock is inactivated automatically. In such case, If buttons on TV are pressed, the screen will display Child Lock,

which can be erased by press of EXIT button. 5 seconds later after the latest press, the screen display will disappear

automatically. The Child Lock mode can be resumed by entering Lock Set menu to set Child Lock off or active Unlock.

Max Volume

Press CH+/- button to select Max Volume. Press VOL+/- button for adjustment between 0 100. If a certain value is set,

when volume is being adjusted, the sound value cannot exceed maximum volume value. If current volume is over

Max Volume, when Lock Set menu is set, current volume will become set maximum volume. If current volume is

below maximum volume, customer set volume will stay unchanged.

Unlock

Press CH+/- button to select Unlock mode.

Press VOL+/- button to unlock all set modes, setting all lock options to off, and the maximum volume returns to 100.

- RGB (PC) mode only; This function doesn`t work for RGB-DTV mode.

- Automatically adjusts picture position and minimizes image shaking.

- After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment.

- The Auto sync are not active in DVI mode.

1. Press MENU button and then use VOL+/- button to select the ADJ. Menu.

2. Press CH+/- button to select Auto Sync.

3. Press VOL+/- button to run Auto Sync.

When Auto Sync has finished, a better quality will be shown on screen.
If the position of the image is still not correct, try Auto adjustment again.

Note: It is better to use Reset instead of Auto sync in 480P,720P,1080i.

4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto

Sync, you can try Auto Sync again.

- Caution: If a 4:3 or one to one fixed image is on the screen for a long time, it may remain visible. This is called burn-in.

- Set every aspect ratio for Video, Component 480i sources.

- Use 4:3, or 16:9 for other RGB-PC and DVI-PC sources.

- Horizon is not available for Component (480p,720p,1080i), DTV (480p,720p,1080i) sources.

Press the ARC button repeatedly to select the desired picture format.

4:3 mode
Choose 4:3 mode when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the
left and right sides.

Full screen( correspond with 16:9)
Choose Full screen when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

one to one
Choose one to one when you want to adjust the picture in real proportion, (Only available in PC signal,
especial for 800X600 mode and modes of under it )

Vertical Zoom
Choose Vertical Zoom when you want to adjust the picture the picture vertically, that is without any back bars.

Half Zoom
Choose Half Zoom when you want to enlarge the picture vertically by enlarge top of the picture, that is the letters on the
bottom are still on the screen.

Panorama
Choose Panorama when you want to enlarge the two sides of the picture in a non-linear proportion.

Display Mode Full screen

Adjust

RGB

Default

Auto Sync.

Color Temper Standard

Black Stretch On

A

B
C

Note:

The setting of aspect ratio is respective in different signal source , that means different aspect ratio could be saved
in different source

- This function works in the following modes:
RGB-PC, RGB-DTV (480p,720p,1080i), DVI-DTV (480p,720p,1080i), COMPONENT(480p,720p,1080i).

1. Press MENU button and then use VOL+/- button to select the ADJ. Menu.

2. Press CH+/- button to select one option and then press VOL+/- to adjust.

3. Press MENU or EXIT to exit it.

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your
new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

1. Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and

a little fabric softener or dish washing detergent. Wring the cloth until it`s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.

If you expect to leave your TV dormant for a long time (such as a vacation), it`s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.

Cell Defects

There may be red spots, blue spots, green spots and black spots on the screen.
This is a characteristic of liquid crystal panels and is not a problem.
The liquid crystal panel is built with very high precision technology giving you fine picture details. Occasionally, a few non­active pixels may appear on the screen as fixed points of red, blue, green, or black.
Please note this does not affect the performance of your LCD TV.