Haier HL32K1b, HL26R1, HL32R1, HL42XR1, HL26K1 Owner's Manual
...
R
TFT-LCD TV
OWNER S MANUAL'
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
MODEL :S
HL26R1
HL32R1
HL42XR1
HL26K1
HL32K1
HL32XK1
HL42XK1
HL32P1
Warning
!
!
The lightning flash with arrowhead symbol, within an
CAUTION
RISK ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
Apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15)The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
16)The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the
apparatus normal use.
Class I apparatus shall be connected to a mains socket outlet with a protective earthing connection.
2 TV LCD-TFT
Safety Instructions
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to
try to correct the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may be not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite cores must be
used when connecting this LCD display to video equipment; and maintain at least 40cm spacing to other
peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
Energy Star compliant( )
By being Energy Star compliant you are assured that your Haier model is helping the environment by using less
energy while saving you money. ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy promoting energy efficiency.
models - HL26R1, HL32R1, HL26K1, HL32K1, HL32XK1,HL32P1
Owner s Manual 3
Safety Instructions
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Haier product. This easy-to-use manual will guide you in getting the best use of your
product. Remember to record the model and serial number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual.You will need it to obtain warranty service.
4 TV LCD-TFT
Contents
Introduction
War ni ng . . . . . . . . .. .. ......... . . . . . . . . . . . . . . . . . . . . .
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...........
Connection Options . . . . . . . . . . . . . . . . . . . . . .........
Remote control . ............ . . . . . . . . .......... . . .........
Installation
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........
Antenna Connection . . . . . . . . . . ..........................
Connecting a VCR. . . . . . . . . . . . . . . . . . . . . ...........
External A/V Source Setup . . . . .. . . . . ..................
Connecting a DVD player . . . . . ...... . . . . . . . . . . . . .
Connecting a DTV(digital TV) ..............................
Connecting digital audio output . . . . . . . . . . . . . . . . .
Connecting a computer. . . . . . . . . . . . . . . . . . . . . . . .
Monitor Out Setup. . . . . . . . . . . . . . . . . . . . .. .. .. .. .. .. .
HDMI and DVI input. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable sample......................................................
Connecting Headphones . . . . . . . . . . . . . . . . . . . .....
Power source................ . . . . . . . . . . . . . . . . . . . . . .
Removing the table stand and installing a
wall mount bracket
Operation
Switching On/Off the TV set . . . . . ... . . . . . . . . . . ....
Choose the Menu Language . . . . ..... ....................
Choose the input source......................................
Channel Menu
Channel Scan............... . . . . . . . . . . . . . . . . . . . . . . .
Channel Skip....... . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel Label....... . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select the desired program. . . . . . . . . . . . . . . . . . . . .
Select the desired sound. . . . . . . . . . . . . . . . . . .. . . .
Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Video Menu
How to select picture mode..................................
How to customize your own picture status .............
Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
...PC
2
3
6
7
8
9
9
10
11
11
12
12
13
14
14
15
16
16
17
18
18
18
19
19
19
20
20
20
21
21
22
Audio Menu
How to select audio mode....................................
How to customize your own audio status ...............
SAP Broadcasts Setup........................................
Function Menu
Menu Language...................................................
OSD Timeout.......................................................
OSD Transparency...............................................
Screen Mode.......................................................
Blue Screen.........................................................
DPMS.................................................................
Time zone setting.................................................
Date /Time setting................................................
Sleep Timer setting..............................................
DTV Caption Style................................................
Lock Menu
Parental Control rating and categories...................
Lock setup...........................................................
Other Functions
Brief Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............
Using the Guide. . . . . . . . . . . . . . . . . . . . . . . ............
Quick program view..............................................
CC (Closed Caption Display) . . . . . . . . . . . . . ... . .. .
USB Input............................................................
Universal Remote Control
Setting up your remote control ..............................
Remote Control Codes ........................................
Maintenance . . .... .. . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Specification . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty ............................................................
.
23
23
.
23
24
24
24
24
25
25
25
25
26
26
27
28
30
30
31
31
32
34
36
42
43
44
45
Owner s Manual 5
Controls
L - AUDIO - R
VIDEO
This is a simplified representation of the TV front panel, side panel control buttons and side inputs.
TV Side panel controls and connections
Introduction
HL26R1/HL32R1/
HL42XR1
HL26K1/HL32K1/
HL32XK1/HL42XK1
VIDEO2 IN
HDMI4 INHDMI3 IN USB
MENU INPUT VOL+ VOL- CH+ CH- POWER MENU INPUT VOL+ VOL- CH+ CH- POWERMENU INPUT VOL+ VOL- CH+ CH- POWER
L - AUDIO - R
VIDEO
HL32P1
1.MENU: Menu display.
2.INPUT: Press to the input source mode.
watch. In the MENU screen, the INPUT button serves as the ENTER button.
3.VOL +/-: Press to adjust the volume. In the MENU screen, these buttons serve as left/right buttons.
4.CH +/- : Press to scan through channels. To scan quickly through channels, press and hold down
either +/- . In the MENU screen, these buttons serve as up/down buttons.
5.POWER: Press to turn on and off the TV.
6.
USB input: Connect a USB flash drive to view JPEG images or listen to MP3 songs.
7.Av2 AUDIO IN: Connect the audio L/R cables from the video signal source to these jacks.
8.AV2 VIDEO IN: Connects the composite video cable from an external signal source to this jack.
9.Headphone jack : Headphone audio output terminal.
10.HDMI IN: Connect a
11. Remote Sensor Receives signals from the remote control.
Do not put anything near the sensor ,
Press to access the on-screen menu display
access Press repeatedly to change the source to the one you want to
HDMI device to receive digital audio and uncompressed digital video signals.
IR
which may block the remote control signal.
6 TV LCD-TFT
Connection Options
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
Back panelconnections
Introduction
ANT IN
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
1. Digital Audio Output:
DVI AUDIO
VGA
AUDIO
VGA AUDIO
AUDIO
AUDIO
S-VIDEO
Connect various types of digital audio equipment.
VGA IN
AV O UT
NOTE: In standby mode, these ports will not work.
2. DVI Audio In:
When using a DVI to HDMI adapter, connect the audio signal to these jacks.
3. Antenna Input: Connect cable or antenna signals to the TV, either directly or through your cable box.
4. HDMI In:
Connect a HDMI device to receive digital audio and uncompressed digital video.
5.VGA Audio In: Connect the audio L/R cables from a computer to this jack.
6.VGA Video In: Connect a video cable from a computer to this jack.
7. VIDEO In: Connects the video signal from a video device.
Component Video
8. In: Connect a component video device to these jacks.
9. AUDIO In: Connect the audio L/R cables from the video signal source to these jacks.
10. S-VIDEO In: Connect the S-Video cable from an external signal source to this jacks.
11. COMPONENT AUDIO In: Connect the audio L/R cables from the component video signal source to these jacks.
12. AUDIO In: Connect the audio L/R cables from the S-Video signal source to these jacks.
13. AUDIO Out: Connect the audio L/R cables to
your audio equipment.
Owner s Manual 7
Universal Remote control
The remote control cannot be operated unless the batteries are properly loaded.
When using the remote control, aim it at the remote sensor on the TV.
Introduction
Function introduction
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TV
STB
CABLE VCR AUD
PICTURE AUDIO PC HDMI
INPUT
MUTE
VOL CH
MENU
ENTER
SLEEP DISPLAY
PLAY/PAUSE
REV
REPEAT
MTS/SAP
FREEZE
GUIDE
CCD ARC
DVD
RECALL
EXIT
STOPUSB REC
PREV NEXT
CH.LIST
FAVORITE
1.POWER
Press to turn on and off the TV.
2.TV DVD SETBOX CABLE VCR
AUD
To select one of the system modes in which the remote control
can be used.
3.PICTURE
Press repeatedly to cycle through the available picture modes.
4. AUDIO
Press to cycle through different sound settings.
5.INPUT
15
16
Show the input source.
6.MUTE
Switches the sound on or off.
video
7.VOLUME UP/DOWN
Press to adjust the volume.
8.MENU
Press to open the on-screen menu.
17
9.THUMBSTICK (Up/Down/Left/Right)
Allows you to navigate the on-screen menus and adjust
the system settings to your preference.
10.SLEEP button
18
19
Press to display the sleep timer option.
11.
USB: Press to switch input source to USB in.
12. MTS/SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog
mode. Change the audio language in DTV mode.
13.GUIDE
20
Press to display the guide when you are watching analog or
digital channels.
14.CCD(closed caption)
21
Select a closed caption.
HDMI:Press to select a device connected to the HDMI input
15.
16.PC:Press to select the computer connected to the VGA input
17.Number buttons
22
Press to change a channel.
18. button
Press to select digital channels. For example, to enter
“54-3”, press “54”, “ ” and “3”.
19.RECALL
23
24
Press to jump back and forth between two channels.
20.CHANNEL UP/DOWN
Press to scan through channels. T
o scan quickly between the
last two channels, press and hold down either +/- .
21.EXIT
Clears all on-screen displays and returns to TV viewing
25
26
27
28
from any menu.
22.
ENTER
Accesses the highlighted item in the on-screen menu
23.DISPLAY
Press to display the TV status information on the top of the TV
screen.
24. Functions
USB
Control the USB System.
/ Rewind / Fast / backward /Forward
Stop Play/Pause REC
REPEAT Repeat
25.FREEZE
Press once to display a frozen image of the current program,
but audio continues. Press again to return to the program.
26.CH.LIST
Open the channel list .
in TV
27.FAV.LIST
Press to open the favorite channel list .
in TV
28.ARC(Aspect Ratio Control)
Press to change the aspect ratio.
8 TV LCD-TFT
ANT IN
ANT IN
Installation
External Equipment Connections
Accessories
DVD
TV
CABLE VCR AUD
STB
PICTURE AUDIO PC HDMI
INPUT
RECALL
MUTE
VOL CH
MENU
EXIT
ENTER
SLEEP DISPLAY
PLAY/PAUSE
STOPUSB REC
PREV NEXT
REV
CH.LIST
REPEAT
MTS/SAP
FREEZE
GUIDE
CCD ARC
FAVORITE
Remote control Owner`s manual Alkaline battery(AAA) 2
Antenna Connection
Over-the-air TV reception quality will depend on your antenna type, antenna location and antenna positioning.
R
TFT-LCD TV
OWNER S MANUAL'
Please READthis manual carefully before
operatingyour TV, and retain it for future
reference.
MODEL:S
HL37T
HL26K
HL52T
HL32K
HL37K
HL42K
HL47K
VHF Antenna
UHF Antenna
ANT IN
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
Bronze Wire
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
To improve the picture quality in a poor signal area,
please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV`s, install a
2-Way Signal Splitter in the connections.
To install the antenna properly please contact a
professional in your area.
Bronze Wire
Be careful not to bend the bronze wire
when connecting the antenna.
Owner s Manual 9
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
External Equipment Connections
NOTE: All cables shown are not included with the TV.
Choose Your Connection
There are several ways to connect your television,
depending on the components you want to connect and
the quality of the signal you want to achieve. The
following are examples of some different ways to connect
your TV with different input sources.
Connecting a VCR
To avoid picture noise (interference), leave an adequate
distance between the VCR and TV.
Installation
Connection Option 1
Set VCR output switch to channel 3 or 4 and then tune
the TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from the VCR's
output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to VCR, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
If you connect a S-VIDEO output from VCR to the
S-VIDEO input, the picture quality is improved;
compared to connecting a regular VCR to the Video input.
2. Insert a video tape into the VCR and press PLAY on
the VCR. (Refer to the VCR owner`s manual.)
3. Select the input source with using the
INPUT button on the remote control, and
then press / button to select the source,
press ENTER button to confirm.
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
AUDIO
S-VIDEO
VGA AUDIO
AUDIO
DVI AUDIO
ANT IN
HDMI IN
AV OUT
10 TV LCD-TFT
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO
AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO
AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
External Equipment Connections
External A/V Source Setup
How to connect
Connect the audio and video cables from the external
equipment's output jacks to the TV input jacks, as shown
in the figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the input source with using the INPUT button on
the remote control.
2. Press / button to select the desired source.
3. Press button to confirm.
ENTER
4. Operate the corresponding external equipment.
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
S-VIDEO
AUDIO
DVI AUDIO
Installation
VGA
AUDIO
Camcorder
ANT IN
HDMI IN
VGA IN
AV OUT
Connecting a DVD player
How to connect
1. Connect the DVD video outputs (COMPONENT) to
the Y Pb Pr jacks on the TV and connect the DVD audio
outputs to the YPbPr Audio IN jacks on the TV, as
shown in the figure.
2. If your DVD only has an S-VIDEO output jack,
connect this to the S-VIDEO input on the TV. as shown
in the figure.
Note
If your DVD player does not have component video
output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use INPUT button on the remote control to select
component mode.
3. Press Play button on external equipment for program
play.
4. Refer to the DVD player's manual for operating
instructions.
Component Input ports
To get better picture quality, connect a DVD player to the
component input ports as shown below.
Component ports
on the TV
Y Pb Pr
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
AUDIO
S-VIDEO
DVI AUDIO
Video Game Set
VGA
AUDIO
ANT IN
HDMI IN
AV OUT
Video output ports
on DVD player
Y Pb Pr
Y B-Y R-Y
Y Cb Cr
Y P P
BR
Owner s Manual 11
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO
AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO
AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
Installation
!
External Equipment Connections
Connecting a DTV(digital TV)
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive
Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
How to connect
Use the TV`s COMPONENT , VGA or HDMI
jack for video connections, depending on
your set-top box connector. Then, make
the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the
owner`s manual for the digital set-top box.)
2. Use INPUT on the remote control to select
COMPONENT , VGA or HDMI source.
Signal
480i
480p
720p
1080i
1080p
COMPONENT
Yes
Yes
Yes
Yes
Yes
HDMI
Yes
Yes
Yes
Yes
Yes
Connecting a digital audio output
Send the TV`s audio to external audio equipment (stereo
system) via the Digital Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Digital
Audio(Optical) Output port.
2. Connect the other end of the optical cable to the digital
audio (optical) input on the audio equipment.
See the external audio equipment instruction manual for
operation.
Note
When connecting with external audio equipments, such
as amplifers or speakers, please turn the TV speakers off.
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
AUDIO
S-VIDEO
Digital Set-top Box
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
AUDIO
S-VIDEO
DVI AUDIO
VGA AUDIO
AUDIO
AUDIO
DVI AUDIO
VGA AUDIO
HDMI IN
AV O UT
HDMI
ANT IN
AUDIO
HDMI IN
VGA IN
AV OUT
Caution: Do not look into the optical output
port. Looking at the laser beam may damage
your vision.
12 TV LCD-TFT
2
1
1
Y
Pb
Pr
L
R
L L
R R
VIDEO
S-VIDEO
VGA
VGA AUDIO
AUDIO AUDIO
L
R
DVI AUDIO
AUDIO
2
L
R
AUDIO
COMPONENT IN
VIDEO IN
1
AV O UT
VGA IN
HDMI IN
ANT IN
OPTICAL OUT
Installation
External Equipment Connections
Connecting a computer
How to connect
1. To get the best picture quality, adjust the VGA graphics card to 1024x768 .
2. Use the TV`s VGA or DVI (Digital Visual Interface)Audio IN port for audio connections, depending on your computer
connector.
If the graphic card on the computer does not output analog and digital RGB simultaneously, connect only one of
either VGA IN or HDMI IN to display the VGA on the TV.
If the graphic card on the computer does output analog and digital RGB simultaneously, set the TV to either VGA or
HDMI ; (the other mode is set to Plug and Play automatically by the TV.)
3. Then, make the corresponding audio connection. If using a sound card, adjust the VGA sound as required.
How to use
1. Turn on the computer and the TV.
2. Use INPUT on the remote control to select VGA or HDMI source.
3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in VGA mode. If noise is present, change the VGA mode to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the VGA
graphic card can not be changed, change the VGA graphic card or consult the manufacturer of the VGA graphic card.
Note
1.Use a DVI cable.
2.Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently
imprinted on the screen.
3. The synchronization input form for Horizontal and Vertical frequencies is separate.
Resolution
Mode
VGA
SVGA
XGA
Resolution
640x480
800x600
1024x768
Frame
frequency
(Hz)
60Hz
60Hz
75Hz
60Hz
75Hz
OPTICAL OUT
COMPONENT IN
VIDEO IN
VIDEO
AUDIO
S-VIDEO
AUDIO
DVI AUDIO
VGA AUDIO
ANT IN
HDMI IN
VGA IN
AV O UT
Owner s Manual 13
Installation
External Equipment Connections
HDMI and DVI input
When the source device(DVD player or Set Top Box) supports HDMI
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).
2. No separated audio connection is necessary.
How To Use
If the source device supports Auto HDMI function, the output resolution of the source device will be automatically
set to 1280x720p.
If the source device does not support Auto HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Select HDMI input source in input source option of Select Main source menu.
When the source device(DVD player or Set Top Box) supports DVI
How To Connect
1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).
2. A separated audio connection is necessary.
3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio
In port located on the left side of HDMI port.
How To Use
If the source device supports Auto DVI function, the output resolution of the source device will be automatically
set to 1280x720p.
If the source device does not support Auto DVI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Press the INPUT button to select HDMI input source in input source option of Select Main source menu.
14 TV LCD-TFT
Cable sample
Installation
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable
(Stereo to RCA type)
(not supplied with the product)
Owner s Manual 15
External Equipment Connections
Connecting Headphones
You can connect a set of headphones to your set if you wish to watch a
TV programme without disturbing the other people in the room.
Installation
HDMI4 INHDMI3 IN
Power source
Plug a set of headphones into the 3.5mm
mini-jack socket on the side panel of the set.
Note
Prolonged use of headphones at a high volume
may damage your hearing.
You will not receive sound from the speakers
when you connect headphones to the system.
Wider Hole
and Blade
Polarized AC Cord Plug
16 TV LCD-TFT
AC Outlet
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for
operation on AC. Insert the AC cord plug into
a standard polarized AC outlet.
Note
Never connect the AC line cord plug to other
than the specified voltage. Use the
attached power cord only.
If the polarized AC cord does not fit into a nonpolarized AC outlet, do not attempt to file or cut
the blade. It is the user`s responsibility to have
an electrician replace the obsolete outlet.
If you cause a static discharge when touching
the unit and the unit fails to function, simply
unplug the unit from the AC outlet and plug it
back in. The unit should return to normal operation.
Removing the table stand and installing a
wall mount bracket
HL42XK1
Installation
Remove 4X M4 screws securing the
stand to the TV, then remove the stand.
HL26R1(4X M4), HL32R1(5X M4),
HL42XR1(4X M4), HL26K1(4X M4),
HL32K1(4X M4), HL32XK1(4X M4),
HL32P1(4X M4)
Use 4X M6 screws to secure the wall
bracket (not supplied) to the back of your TV.
HL26R1(4X M4), HL32R1(4X M4),
HL42XR1(4X M4), HL26K1(4X M4),
HL32K1(4X M4), HL32XK1(4X M4),
HL32P1(4X M4)
Owner s Manual 17
Operation
In the manual, the OSD (on screen display) may be
different from your TV`s, because it is just an example to
help you with the TV operation.
There are several options you might need to set up in order
for your TV to work properly. Read the instructions that
follow.
Initial Setup: Set according to the screen display.
Switching On/Off the TV set
.
1 First, connect power cord correctly.
.
2 Select the viewing source by using INPUT button on
the remote control.
.
3 When finished using the TV, press POWER button on
the remote control. The TV reverts to standby mode.
4 If you intend to be away on vacation, disconnect the
.
power plug from the wall power outlet.
Note
If the TV in power on , the screen show information
according the type of input signal . the information will
disappear. If there is no signal , No Signal will display
on the screen.
Operation
Choose the Menu Language
When you start using your set for the first time, you must
select the language which will be used for displaying menus
and indications.
1. Choose TV Input and then pressMENU button.
2. Press / button to select Function menu.
3. Press ENTER button and then use / button to
/
select Language.
4. Press button to select language.
/
English Spanish or French
Choose the Input source
Change the picture source so you can watch your TV,
VCR, DVD, Cable , or any other devices that are
connected to your TV.
1. Press INPUT button to enter the Select Source menu
and then use / button to select the desired items
(TV, Video1, Video2, S-Video,Component1, Component2,
, HDMI1,HDMI2,HDMI3,HDMI4).
PC
2. Press ENTER button to confirm .
Video
Audio
Channel
Function
Lock
Function
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
Blue Screen On
DPMS On
Time Setup
Closed Caption
Default
Select Source
TV
Video1
Video2
S-Video
Component1
Component2
PC
HDMI1
HDMI2
HDMI3
HDMI4
Select
EXIT
/
Back
18 TV LCD-TFT
Channel menu
This TV set has two methods to set channels, which are
respectively Channel Scan, Channel Skip.
In this section, how to use the remote control to set
channel is explained. You can also use buttons on the TV to
set channel.
Note
The Channel menu will be only operated in normal TV mode.
Channel Scan
1. Press MENU button and then use / button to select
Channel menu.
2. Press ENTER button to select Tuner.
3. Press button to selectCable or Antenna mode.
4. Press / button to select Channel Scan.
5. Press ENTER button to start searching.
6. To cancel searching, press EXIT button.
Note
When Antenna is selected, the TV will detect antenna
signals and will search for antenna TV (NTSC and
ATSC) channels available in your local area.
When Cable is selected, the TV will detect cable
company supplied signals and will search for cable TV
(NTSC,QAM modulated) channels available in your
Area.
/
/
/
Video
Audio
Channel
Function
Lock
Channel
Video
Audio
Channel
Function
Lock
Channel Scan
Operation
Tuner Antenna
Channel Scan
Channel Skip
Channel Label
ENTER
Status: Antenna
Scanning
Analog Channels: 19
Digital Channels: 0
64%
Select
EXIT
EXIT
BackScan
Cancel
/
Channel Skip
A skip channel is skipped when using / button to
browse the channels. A skip channel can be watch
by key-in the channel number or select by list.
Default un-scanned analog channels are skip.
Channel with a check icon is a skipped channel.
1. Press MENU button and then use / button to select
Channel menu.
2. Press / ENTER button and then use / button to
select Channel Skip.
3. Press / button to select a channel, then press ENTER
button to toggle between and .
Channel Label
Allows you to name the channel that is selected.
Press /ENTER button to enter the submenu.
Then press / to select Channel Index and Channel
Label and / to select the position of the item that you
want to change, afterward press INPUT to input the
numbers and symbols and ENTER button to confirm.
Video
Audio
Channel
Function
Lock
Channel Skip
Video
Audio
Channel
Function
Lock
Channel Label Set
1
Analog
2
Analog
3
Analog
4
Analog
5
Analog
5-1
Digital KPIX-DT
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
Channel Index
Channel Label
ENTER
Select
EXIT
1
Select
EXIT
BackSet
Back
/
/
Owner s Manual 19
Select the desired program
Using CH+/- buttons.
1
.
Press CH+ button to select a channel number in
number increasing direction.
Press CH- button to select a channel number in
number decreasing direction.
Note
If skip is ON on one channel, press CH+/- button, the
channel will not appear.
Also can enter channel number directly,eg:2-0.
2.
Select the desired sound
Press VOL-/+ buttons on the remote or the front of the
TV set to adjust the volume level. The range is 0~100.
When the volume buttons are pressed the volume level
is displayed automatically on the TV screen.
Mute
Operation
Volume
1. Press MUTE button on the remote control and
icon will display on the screen. At this time, the sound
of the TV set is turned off.
2. If you want to recover the sound, press MUTE
button again or directly press VOL+ button.
20 TV LCD-TFT
Video menu
The TV menu gives you an overview of the menus you can select.
Note
Depending on the input signal, one or more menu items may not be selectable.
How to select picture mode
The picture mode provides the pre-defined images settings:
Standard, Vivid, Custom and Mild .
1. Press MENU button and then use / button to select
Video menu.
2. Press ENTER button and then use / button to
select Mode.
3. Press / button to select the option Standard, Vivid,
Custom and Mild.
You can also press PICTURE button on the remote control
to select the option .Standard, Vivid, Custom and Mild
/
Video
Video
Audio
Channel
Function
Lock
Mode Custom
Brightness
Contrast
Color
Tint
Sharpness
Color Temperature
Advanced Video
Select
/
Operation
59
59
59
7
58
EXIT
Back
How to customize your own picture
status
.
1 Press MENU button and then use / button to select
Video menu.
. ENTER
2 Press button and then use / button to
select the desired items.
. ENTER
3 Press button and then use / button to
adjust the setting.
Mode
Select the mode of picture( ).
Brightness
This will adjust the light output of the complete picture,
which will mainly affect the darker areas of the picture.
Contrast
This will adjust the intensity of bright parts in the picture
but keep the dark parts unchanged.
Color
This will adjust the saturation level of the colors to suit
your personal preference.
Tint
Allows you to select the color mix (Tint) of the picture.
/
/
Standard/ Vivid/ Custom/ Mild
Note
Only when the item of mode is custom , the
Brightness, Contrast, Color, Tint, Sharpness
and Color Temperature
can be set by user .
In other mode the value of them are preset.
Sharpness
This will adjust the sharpness of fine details in the picture.
Owner s Manual 21
Video menu
Color temperature
This will increase or decrease Warm (red) and Cool (blue)
colors to suit personal preferences.
Select Cool to give the white colors a blue tint, Standard
to give the white colors a neutral tint, Warm to give the
white colors a red tint.
Advanced Video
To adjust the picture in advanced: DNR, Black Level Extender,
White Peak Limiter, CTI, Flech Tone, Adaptive Luma Control.
DNR
To adjust reduce the appearance of digitizing error by the compression:
Off, Weak, Medium, Strong, Auto.
Black Level Extender
To adjust the ability in the black areas detail of the picture: On and Off.
White Peak Limiter
To adjust the ability in the white areas detail of the picture: On and Off.
CTI
To adjust the picture for color errors: Off, Weak, Medium and Strong.
Flesh Tone
To adjust the flesh color: On and Off.
Adaptive Luma Control
To adjust changes in the luminance of the picture: On and Off.
Video
Audio
Channel
Function
Lock
Advanced Video
DNR
Black Level Extender
White Peak Limiter
CTI
Flesh Tone
Adaptive Luma Control
Operation
Medium
On
On
Medium
On
On
Select
EXIT
/
Back
PC Set
When you select the input, this function is used.PC
Adjustment for screen Position, Clock, Phase, Setting
Display adjust menu by pressing INPUT button then use
/ button to select the the source of item.
Auto sync: Automatically adjust display of the picture
(Only available in source).
PC
Position : Adjust the screen position.
Phase : Adjust the phase of Pixel clock.
Clock : Adjust the clock of input signal.
1. Press MENU button and then use / button to select
Video menu.
2. Press / ENTER button and then use / button to
select .
PC
3. Press / ENTERbutton and then use / button to
adjust the setting.
PC
Video
Audio
Function
Lock
Video
Video
Audio
Function
Lock
PC
Mode Custom
Brightness
Contrast
Color Temperature
Advanced Video
PC
/
Auto Sync
H Position
V Position
Phase
Clock
ENTER
/
Select
Select
EXIT
EXIT
59
59
Back
59
59
59
59
BackEnter
22 TFT-LCD TV
Audio menu
How to select audio mode
1. Press MENU button and then use / button to select Audio
menu.
2. Press / ENTER button and then use / button to select
Mode.
3. Press / ENTERbutton to select the option Off, Concert,
Living Room, Hall, Bathroom, Cave, Arena and Church.
You can also press AUDIO button on the remote control to select
the Audio Mode Off, Concert, Living Room, Hall, Bathroom, Cave,
Arena and Church.
How to Customize your own audio status
1. Press MENU button and then use / button to select Audio
menu.
2. Press / ENTER button and then use / button to select
desired items.
3. Press / ENTERbutton and then use / button to adjust
the setting.
Balance
Adjust to emphasize left or right speaker balance.
Bass
Adjust to increase or decrease lower-pitched sounds.
Treble
Adjust to increase or decrease higher-pitched sounds.
SRS TS XT
To turn the simulated surround sound on and off.
Mode
To adjust the audio mode: Off, Concert, Living Room, Hall,
Bathroom, Cave, Arena and Church.
Equalizer
To adjust the equalizer: Off, Rock, Pop, Live, Dance, Techno,
Classic and Soft.
SPDIF Type
To Adjust the SPDIF output: Off, Dolby Digital and PCM.
AVL(Automatic Volume Control)
This will reduces the differences in volume level among broadcasters.
Audio Only Press / ENTER button to confirm, the following
display will appear on the screen.
If enter Audio Only mode, press “POWER” to exit!
OK Cancel
Press to select OK , then press OK to confirm. The TV screen will
be black and no picture , but the sound is still normal.
You can press POWER button to reveal the picture on the screen.
Audio
Video
Audio
Channel
Function
Lock
Operation
Balance
Bass
Treble
SRS TS XT On
Mode Off
Equalizer Off
SPDIF Type PCM
AVL Off
Audio Only
ENTER
/
Select
EXIT
0
59
59
BackAdjust
SAP Broadcasts Setup
This TV can receive MTS stereo programs and SAP (Secondary
Audio Program) that accompanies the stereo program; if the
station transmits an additional sound signal as well as the
original one.
When having selected SAP button on the remote control, this TV
can only receive the signal when the TV station transmits the
proper signals.
Mono sound is automatically received if the broadcast is only in
Mono; even though Stereo or SAP has been selected.
Select Mono if you want to listen to mono sound during stereo/SAP
broadcasting. Stereo or SAP can be received in a Analog channel.
1. Use SAP button to select your desired MTS mode in a analog signal.
Each time you press SAP button, Mono, Stereo or SAP appear.
If other languages are available on the digital signal, select them
with the SAP button.
2. Press EXIT button to save and return to TV viewing.
Owner s Manual 23
Function menu
Menu Language
When you start using your set for the first time, you must
select the language which will be used for displaying menus
and indications.
1. Press MENU button and then use / button to select
Function menu.
2. Press / ENTER button and then use / button to
select Language.
3. Press / button to select language.
English Spanish or French
OSD Timeout
1. Press MENU button and then use / button to
select Function menu.
2. Press / ENTER button and then use / button to
select OSD Timeout.
3. Press / button to select Short, Middle or Long.
(Short is for 5 seconds; Middle is for 10 seconds;
Long is for 15seconds)
Video
Audio
Channel
Function
Lock
Function
Operation
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
Blue Screen On
DPMS On
Time Setup
Closed Caption
Default
Select
/
EXIT
Back
OSD Transparency
1. Press MENU button and then use / button to select
the Function menu.
2. Press / ENTER button and then use / button to
select OSD transparency.
3. Press / button to select Low ,Middle or High.
Screen Mode
Lets you choose the way an analog picture with a 4:3 aspect
ratio is displayed on your TV with a 16:9 ratio picture format.
Note
If a fixed image is displayed on the screen for a long time,
the image may become permanently burned on the screen
and remain visible.
1. Press MENU button and then use / button to select
Function menu.
2. Press / ENTER button and then use / button to
select Screen Mode.
3. Press / button to select Normal, Zoom, Wide or
Cinema.
Normal
Choose normal when you want to view the picture with
4:3 mode .
Zoom
Choose Zoom when you want to view the picture without
any alteration. However, the top and bottom portions
of the picture will be cropped.
Video
Audio
Channel
Function
Lock
Function
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
Blue Screen On
DPMS On
Time Setup
Closed Caption
Default
Select
/
EXIT
Back
24 TV LCD-TFT
Function menu
Wide
Choose wide when you want to adjust the picture
horizontally, in a linear proportion to fill the entire screen.
Cinema
For letterbox pictures, bars may appear on the top and
bottom on some programs.
You can also press button on the remote control to
select
the desired picture format: Normal, Zoom, Wide or
Cinema.
Blue Screen
1. Press MENU button and then use / button to select
Function menu.
2. Press / ENTER button and then use / button to
select Blue Screen.
3. Press / button to select On or Off.
DPMS
PC Power Management. To set On, the set will be in
standby mode automatically if no signal in 2 minutes; if
signal input, the set will be on again automatically.
Note: DPMS is useful only in VGA source.
ARC
Operation
Time zone setting
This function allows you to select your local time zone.
Broadcasted time information will correct the clock display
for your local time.
1. Press MENU button and then use / button to
select Function menu.
2. Press / ENTER button and then use / button to
select Time Setup.
3. Press / ENTER button and then use / button to
select Time Zone.
4. Press / button to select your viewing area time zone:
Eastern, Central, Mountain, Pacific, Alaska or Hawaii .
Date /Time setting
Setting the clock is necessary in order to use the various
timer features of the TV. Also, you can check the time
while watching the TV.
1. Press MENU button and then use / button to
select Function menu.
2. Press / ENTER button and then use / button to
select Time Setup.
3. Press or ENTER button and then use / button to
select Date/Time.
4. Press / ENTER button and then use / button to
select On or Off.
Video
Audio
Channel
Function
Lock
Time Setup
Video
Audio
Channel
Function
Lock
Date/Time
Time Zone Pacific
Date/Time
Sleep Timer Off
Auto On
Date
Time
Timer Off
On Time
Off Time
2008/01/01
11:54 AM
11:54 AM
12:00 AM
Select
EXIT
Select
EXIT
Back
Back
/
/
Owner s Manual 25
Function menu
Sleep Timer setting
The sleep timer automatically shuts off the TV after a
preset time (from 5 to 240 minutes).
1. Press MENU button and then use / button to
select Function menu.
2.Press / ENTER button and then use / button to
select Time Setup
3. Press / ENTER button and then use / button to
select Sleep Timer.
4. Press / button to select the number of minutes.
Select Off,5Min,10Min, 15Min, 30Min, 45Min,60Min,
90Min, 120Min, 180Minor 240Min.
The time begins to count down from the number of
minutes selected.
5. To cancel the set sleep timer: Press button to select
Off.
You can also press SLEEP button to select quickly the
sleep timer.
DTV Caption Style (In DTV mode)
This allows you to modify how digital captions are displayed
on your TV. Select from the following options to change the
visual characteristics of your TV`s digital captioning.
Customize the DTV/CADTV captions that appear on your
screen.
1. Press MENU button and then use / button to select
Function menu.
2. Press / ENTER button and then use / button to
select Closed Caption .
3. Press / ENTER button and then use / button to
select DTV Caption Style.
4. Press / ENTER button and then use / button to
select the Style, Size, etc., press / button to
customize to your preference.
Style
Select this option to select the font style of caption display
according to your own preference.
Press / button to select Default or Custom.
Size
Select this option to select the size of caption display
according to your own preference.
Press / button to selectSmall, Normal or Large.
Text color
Select this option to select the text color or the opacity of
the text box of caption display according to your own
preference.
Select a color and one of the opacity options.
Text Opacity
Specify the opacity for the text color.
BG Color
Select a background color.
BG Opacity
Select the opacity for the background color.
Window Color
Select a window color.
Window Opacity
Select the opacity for the window color.
Video
Audio
Channel
Function
Lock
Time Setup
Video
Audio
Channel
Function
Lock
Function
Video
Audio
Channel
Function
Lock
Closed Caption
Video
Audio
Channel
Function
Lock
DTV Caption Style
Operation
Time Zone Pacific
Date/Time
Sleep Timer Off
Select
/
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Normal
Blue Screen On
DPMS On
Time Setup
Closed Caption
Default
Select
ENTER
NTSC Caption Off
DTV Caption Off
DTV Caption Style
ENTER
Style
Size
Text Color
Text Opacity
BG Color
BG Opacity
Window Color
Window Opacity
/
Select
/
Custom
Normal
Black
Solid
Black
Solid
White
Solid
Select
/
EXIT
EXIT
EXIT
EXIT
Back
BackEnter
BackEnter
Back
26 TV LCD-TFT
Operation
Lock Menu
Parental Control can be used to block specific channels, ratings and other viewing sources.
The parental control function is used to block program viewing based on the ratings sent by the broadcasting station.
The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program
and the categories.
Parental Control rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be
blocked by TV Rating or Individual Categories. Movies that have been shown at the theaters or direct-to-video
movies use the Movie Rating System (MPAA) only.
Ratings for Television programs :
Parental Guide
TV-Y (All children)
TV-Y7 (Children 7 years older)
TV-G (General audience)
TV-PG (Parental guidance suggested)
TV-14 (Parents strongly cautioned)
TV-MA (Mature audience only)
Ratings for Movies previously shown in theaters:
MPAA Rating :
G (General audience)
PG (Parental guidance suggested)
PG-13 (Parents strongly cautioned)
R (Restricted)
NC-17 (No one 17 and under admitted)
X (Adult only)
If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.
CA Eng Rating
C Children
C8+ Children eight years and older
G General Programming, suitable for all audiences
PG Parental Guidance
14+ Viewers 14 years and older
18+ Adult Programming
CA Fren Rating
G General
8 ans+ Not recommended for young children
13 ans+ Programming may not be suitable for children under the age of 13
16 ans+ Programming is not suitable for children under the age of 16
18 ans+ Programming restricted to adults
TV Rating :
A (Age)
D (Dialogue - sexual dialogue)
L (Language - adult language)
S (Sex - sexual situations)
V (Violence)
FV (Fantasy Violence)
(applies to TV-Y, TV-Y7,TV-G,TV-PG,TV-14, TV-MA)
(applies to TV-PG, TV-14)
(applies to TV-PG, TV-14, TV-MA)
(applies to TV-PG, TV-14, TV-MA)
(applies to TV-PG, TV-14, TV-MA)
(applies to TV-Y7)
Owner s Manual 27
Lock Menu
Lock setup
Set up blocking schemes to block specific channels, ratings,
and external viewing sources.
A password is required to gain access to this menu.
1. Press MENU button and then use / button to select
Lock menu. Then, press button.
The TV is set up with the initial password 0-0-0-0 and
security default password is 9-4-4-3.
2. Use / button to select the desired items, and press
or ENTER button to enter the next menu. Once the option
is selected, change the settings to your preference.
Password
Change the password by inputting a new password twice.
Channel Block
1. Press MENU button and then use / button to select
Lock menu.
2. Press ENTER button and then use / button to
select Channel Block.
3. Press / button to select the item, Press OK button
to set.
/
Video
Audio
Channel
Function
Lock
Lock
Video
Audio
Channel
Function
Lock
Channel Block
Enter Password
2
Analog
3
Analog
4
Analog
5
Analog
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
11
Analog
12
Analog
ENTER
Operation
EXIT
Back
EXIT
Select
Set
/
Back
Parental Lock
1. Press / button to select Lock item.
Parental
2. Press / button to select On or Off.
Note
If the Parental Lock is setting as Off, the change of the
Parental Guide , MPAA Rating ,CA Eng Rating and CA
Fren Rating will be no useful.
Parental Guide
Note
The Parental control will automatically block certain
categories that are more restrictive . For example, if
you block TV-Y category, then all the categories in
the young adult group will be blocked (TV-Y, TV-Y7,
TV-G, TV-PG, TV-14 and TV-MA).
The sub-ratings (D, L, S, V, FV) work together similarly.
How to set the D, L, S, V and FV sub-ratings.
First, press / button select one of these Ratings:
TV-Y, TV-Y7, TV-G, TV-PG,TV-14, or TV-MA , and press
/ button.
Video
Audio
Channel
Function
Lock
Lock
Video
Audio
Channel
Function
Lock
Program Block
Channel Block
Program Block
Password
Clean All
ENTER
Enter
Parental Lock On
Parental Guide
MPAA Rating
CA Eng Rating
CA Fren Rating
Digital Rating
Block Unrated On
Enter
ENTER
Select
EXIT
Select
EXIT
Back
Back
/
/
28 TV LCD-TFT
Lock Menu
Lock setup
A symbol will be displayed for each sub-rating.
While is selected, press button to go to a sub
rating. To select a different Rating, press / buttons
and then repeat the process.
Note
The V-chip will automatically block certain categories
that are More restrictive .For example, if you block
sub-rating in TV-PG, then the sub-ratings in
TV-14 and TV-MA will automatically be blocked.
MPAA Rating
Blocks movies according to the movie ratings limits
specified, so children cannot view certain movies. You
can set the ratings limit by blocking out all the movies with
the ratings above a specified level. Keep in mind that the
movie ratings limit only applies to movies shown on TV,
not TV programs, such as soap operas.
1. Press / button to select MPAA Rating item.
2. Press / ENTER button and then use / button to
select the rating.
3. Press ENTER button to set block or unblock.
ENTER
Video
Audio
Channel
Function
Lock
Parental Guide
Video
Audio
Channel
Function
Lock
MPAA Rating
Operation
A D L S V FV
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Allowed Rating Blocked Rating
Select
Set
ENTER
G
PG
PG-13
R
NC-17
X
Allowed Rating Blocked Rating
Set
ENTER
EXIT
/
EXIT
Select
/
Back
Back
CA Eng Rating
Canadian English Language Rating
1. Press / button to select CA Eng Rating item.
2. Press / ENTER button and then use / button to
select the rating.
3. Press ENTER button to confirm.
CA Fren Rating
Canadian French Language Rating
1. Press / button to select CA Fren Rating item.
2. Press / ENTER button and then use / button to
select the rating.
3. Press ENTER button to confirm.
Video
Audio
Channel
Function
Lock
CA Eng Rating
Video
Audio
Channel
Function
Lock
CA Fren Rating
C
C8+
G
PG
14+
18+
Allowed Rating Blocked Rating
ENTER
Set
G
8 ans+
ans
13 +
16 +
ans
18 +
ans
Allowed Rating Blocked Rating
Set
ENTER
EXIT
Select
/
Select
EXIT
/
Back
Back
Owner s Manual 29
Other Functions
Brief Info
Brief Info shows the present screen information.
Press DISPLAYbutton to show the Brief Info on the screen.
Press DISPLAYbutton or EXIT button to exit.
Function:
Show the present screen information.
Press button or EXIT button to exit.
DISPLAY
A: Video resolution
B: Program name
C: Program rating categories
D: program show time
E: Program title
F: Channel Lable
G:Tuner mode
H:Program details
Operation
Using the Guide
The guide allows you to select the channels from a channel
list.
The guide allows provides information about the current
program being shown on each channel(if information is
available from the station).
Note
Program information in the guide is provided by the
broadcasters. As a result, it may sometimes include only
the channel number, without a program title or description.
A: Program title
B: program options
C: program show time
D: Program details
E: Program rating categories
30 TV LCD-TFT
Loading...