Haier HL32ATB, HL26ATB User Manual

Download

OWNER S MANUAL'

Please READ this manual carefully before operating your TV, and retain it for future reference.

TFT-LCD TV

MODEL :

HL26ATB HL32ATB

CAUTION

RISK ELECTRIC SHOCK DO NOT OPEN

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. Read the following safety instruction before starting the operation.

The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties:

THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT WITH ANY INSIDE PART OF THIS PRODUCT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However ,there is no guarantee that interference with not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures: *Reorient or relocate the receiving antenna. *Increase the separation between the equipment and receiver. *Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. *Consult the dealer or an experienced radio/TV technician for help. This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may be not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: To assure continued compliance and possible undesirable interference, the provided ferrite cores must be used when connecting this plasma display to video equipment; and maintain at least 40cm spacing to other peripheral device.

CANADIAN NOTICE: This Class B digital apparatus compiles with Canadian ICES-003.

2 TV LCD-TFT

IMPORTANT SAFETY INSTRUCTIONS

Read all of the instructions before using this appliance. When using this

appliance, always exercise basic safety precautions, including the following:

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer`s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of

time.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) WARNING-To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,

shall be placed on the apparatus.

PORTABLE CART WARNING

(symbol provided by RETAC)

S3126A

Owner s Manual 3

SAVE THESE INSTRUCTIONS

Thank you for using our Haier product. This easy-to-use manual will guide you in getting the best use of your product. Remember to record the model and serial number. They are on label in back of the unit.

Model number

serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

Contents

War nin g . . . . . . . ...... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .

Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Introduction

Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. ... ... ...... .

Connection Options . . . . . . . . . . . . . . . . . . . . . .............

Universal Remote Controller . ............ . . . . . . . . ......

Installation

Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. ... ...... .

Antenna Connection . . . . . . . . . . ..............................

VCR Connection. . . . . . . . . . . . . . . . . . . . . ............... ..

External A/V Source Setup . . . . .. . . . . ......................

DVD Connection . . . . . ...... . . . . . . . . . . . . . ................

DTV Connection.....................................................

HDMI Connection . . .... . . . . . . . . . . . . . . . . . ..............

Cable Sample.........................................................

PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................

Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .

Power Source................ . . . . . . . . . . . . . . . . . . . . . . . ..

Operation

Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...

Choose the Menu Language . . . . ..... .......................

Choose the Input Source.........................................

Channel Menu

Scan Channel. . . . .... . . . . . . . . ............................. ..

Add C han nel . . . . ... ... ...... .. . . . . . . . . . . . . . . . . . . . . .. .

Favorites................................................................

Cha nne l Lis t.. ... ...... ... . . . . . . . . . . . . . . . . . . . . . . . . . ...

Video Menu

Picture Settings

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . ... . . . . . ..

Screen adjustment .................................................

Color Temperature .................................................

Back Light..............................................................

......................................................

Audio Menu

Bass,Treble and Balance Setup

MTS ......................................................................

Digital Audio Language

TV Speaker ............................................................

Mute .....................................................................

Settings Menu

Timer setting..........................................................

Sleep Timer setting.................................................

Date & Time setting...................................................

Today`s Date and Current time setting

Time zone setting...................................................

Daylight Saving setting...........................................

Closed Captions.....................................................

CC Activation.........................................................

Caption Service

Digital Caption Service...........................................

Digital Caption Option............................................

Caption Preference ...............................................

Parental Control ....................................................

Others Functions

Quick Program View...............................................

Setting Up Your Remote Control ..............................

Remote Control Codes ...........................................

Maintenance . . ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty ..............................................................

............................................

......................................................

...............................

.....................

4 TV LCD-TFT

Controls

-This is a simplified representation of front panel.

-Here shown may be somewhat different from your TV.

Front panel controls

Introduction

HL26ATB

1.INPUT: A

2.CH( ) Program minus and plus, menu options

3.VOL( ) Volume increase and decrease, menu reset and entry

4.MENU Menu display

POWER : Is used to activate the display or return to standby mode.

HL32ATB

INPUT

VOL

ll input source display and OK confirm.

4 5

Owner s Manual 5

Connection Options

Back panel controls

Introduction

Antenna Input Connect cable or antenna signals to the TV, either directly or through your cable box.

TV RS-232

RS-232 INPUT

(CONTROL/SERVICE PORT)

Connect to the RS232 port on a PC.

PC VIDEO Input

Connect the monitor output connector from a PC to the jack

HDMI INPUT

connect a signal to HDMI/DVI.

PC/DVI AUDIO Input

connect the audio

from an external

HDMI L/R

device.

VGA/DVI

For service

USB

For Service

Connects the video

from a video device.

CVBS S-VIDEO

S-Video Input

Connect S-Video out from an S-VIDEO device to the S-VIDEO input.

AV Input

and audio signal

CVBS -L/R S-Video -L/R

AUDIO output

connect to

external

amplifier device.

YPbPr -L/R

Pb Pr

DVD/DTV Input

(Component )

Connect a component video device to these jacks.

L/R Audio Out

Earphone jack:

Earphone audio output terminal.

EARPHONE

6 TV LCD-TFT

Universal Remote Controller

- The remote controller cannot be operated unless the batteries are properly loaded.

- When using the remote control, aim it at the remote control sensor on the TV.

Introduction

Function introduction

Turns your TV or any other programmed

equipment on or off, depending on mode.

Open the channel list.

Select the desired source.

Open the favorite channel list.

Select the subchannel

CC(closed caption)

Select a closed caption:

CC ON, CC OFF.

More information display.

Brings up the main menu to the screen.

Clears all on-screen displays and

returns toTV viewing from any menu.

Switches the sound on or off

(Aspect Ratio Control)

Changes the aspect ratio.

POWER

CH.LIST

Source Select

FAVORITE

GUIDE

EXIT

MUTE

ARC

TV DVD VCR SETBOX CABLE AUDIO

Press the SELECT button repeatedly to select one of the system modes in which the remote control can be used.

When the desired device is selected, the corresponding LED lights on 5seconds.

HDMI source select

Open the HDMI source.

CH.LIST

TV CVBS

HDMI

SEL ECT

VGA

S-VIDEO

YPbPr

VGA source select

Open the VGA source.

VCR/DVD Functions

Control some video cassette recorders or DVD players.

/ Rewind / Fast / backward /Forward

Stop Play/Pause REC

TIME Open the current time display.

AUTO ADJUST

Automatic adjust the H-position,V-position,phase

FAV.

TIME

AUTO

NPUT

UIDE

INFO

INPUT

show the input source mode.

VOL +

VOL-

CH+

CH-

INFO

When you watch the TV, press the key, the information displays on top of the screen.

THUMBSTICK (Up/Down/Left/Right/OK)

Allows you to navigate the on-screen menus and adjust the system settings to your preference.

SLEEP button

Displays the Sleep Timer option.

LIGHT

Press the light button, white LED will be ON, release this key, white LED will be OFF.

SAP

Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode.

Increases/decreases the sound level.

Numeric buttons

VOLUME UP/DOWN

press to change the channel.

- button

Press to select additional channels

being broadcast by the same station.

“54-3”, press “54”, then press “-” and “3”.

For example, to select channel

(digital and analog)

CHANNEL UP/DOWN

Selects available channels

Q.VIEW

Switch the current channel to the last channel you have viewed.

Owner s Manual 7

External Equipment Connections

Accessories

SELECT

CH.LIST

FAV.LIST

AUDIO LIST

PIP SWAP

AUDIO SWAP

POSITION

S.MODE

P.MODE

FREEZE

IN F

N E

I T

L S

A R

VOL+

CH+

VOL-

CH-

Q.VIEW

Installation

Remote controller

Owner`s manual

Alkaline battery(AAA) 2

Power cable

Antenna Connection

Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an outdoor antenna .In different places, the suitable antenna type and position are different.

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Wall Antenna Socket

Bronze Wire

RF Coaxial Wire (75 ohm)

VHF Antenna UHF Antenna

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Outdoor Antenna

Turn clockwise to tighten.

Bronze Wire

Be careful not to bend the bronze wire when connecting the antenna.

8 TV LCD-TFT

To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV`s, install a 2-

Way Signal Splitter in the connections.

If the antenna is not installed properly, contact your dealer

for assistance.

External Equipment Connections

NOTE: All cables shown are not included with the TV.

Choose Your Connection

There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some ways to connect your TV. Choose the connection which is best for you.

VCR connection

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

Connection Option 1

Set VCR output switch to channel 3 or 4 and then tune the TV to the same channel number.

Installation

Connection Option 2

1. Connect the audio and video cables from the

VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner`s manual.)

3. Select the input source with using the

INPUT button on the remote control to select the source.

CVBS S-VIDEO

CVBS -L/R S-Video -L/R

YPbPr -L/R

Pb Pr

L/R Audio Out

EARPHONE

Owner s Manual 9

External Equipment Connections

External A/V Source Setup

How to connect

Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Select the input source with using the INPUT button on the remote control.

2. Operate the corresponding external equipment.

CVBS S-VIDEO

CVBS-L/R S-Video -L/R

YPbPr -L/R

Pb Pr

Installation

EARPHONE

L/R Audio Out

Camcorder

Video Game Set

DVD connection

How to connect

1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb, Pr jacks on the TV and connect the DVD audio outputs to the YPbPr Audio IN jacks on the TV, as shown in the figure.

2. If your DVD only has an S-VIDEO output jack, connect this to the S-VIDEO input on the TV. as shown in the figure.

NOTE: If your DVD player does not have component video

output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT button on the remote control to select YPbPr mode.

3. Press Play button on external equipment for program play.

4. Refer to the DVD player's manual for operating instructions.

Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

Y Pb Pr

CVBS S-VIDEO

CVBS-L/R S-Video -L/R

YPbPr -L/R

Pb Pr

L/R Audio Out

EARPHONE

Video output ports on DVD player

10 TV LCD-TFT

Y Pb Pr Y B-Y R-Y

Y Cb Cr Y P P

Installation

External Equipment Connections

DTV connection

- This TV can receive Digital Over-the-Air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV`s (Y, PB, PR) , VGA or HDMI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner`s manual for the digital set-top box.)

2. Use INPUT on the remote control to select YPbPr, VGA, or HDMI source.

RS-232

HDMI L/R

CVBS S-VIDEO

CVBS-L/R S-Video -L/R

YPbPr -L/R

Pb Pr

Signal

480i

480p

720p

1080i

YPbPr

Yes

HDMI/DVI

Yes

Digital Set-top Box

HDMI connection

How To Connect

1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI input source in input source option of Select Main source menu.

How To Connect

1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).

2. A separated audio connection is necessary.

3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio In port located on the left side of HDMI port.

How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Press the INPUT or HDMI button to select HDMI input source .

Owner s Manual 11

Cable sample

Installation

HDMI Cable (not supplied with the product)

HDMI to DVI Cable (not supplied with the product)

Analog Audio Cable (Stereo to RCA type) (not supplied with the product)

12 TV LCD-TFT

Installation

External Equipment Connections

PC connection

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024x768 .

2. Use the TV`s PC or DVI (Digital Visual Interface) port for video connections, depending on your PC connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherVGA IN or DVI IN to

display the PC on the TV.

If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either VGA or DVI; (the other mode is

set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Use INPUT or VGA or HDMI on the remote control to select VGA or HDMI source.

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode.

If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES: 1 Use a DVI cable. 2 Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the

screen. 3 The synchronization input form for Horizontal and Vertical frequencies is separate.

Resolution

Mode

VGA

SVGA

XGA

Resolution

Frame frequency (Hz)

640*480 60Hz

800*600 60Hz/75Hz

1024*768

60Hz

75Hz

RS-232

HDMI L/R

CVBS S-VIDEO

CVBS-L/R S-Video -L/R

YPbPr -L/R

Pb Pr

Owner s Manual 13

External Equipment Connections

Connecting Headphones

You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room.

Plug a set of headphones into the 3.5mm mini-jack socket on the rear panel of the set.

L/R

EARPHONE

Audio Out

Note

Prolonged use of headphones at a high volume

may damage your hearing.

You will not receive sound from the speakers

when you connect headphones to the system.

Installation

Power Source

Wider Hole and Blade

Polarized AC Cord Plug

AC Outlet

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet.

NOTES:

Never connect the AC line cord plug to other than the specified voltage. Use the attached power cord only.

If the polarized AC cord does not fit into a nonpolarized AC outlet, do not attempt to file or cut the blade. It is the user`s responsibility to have an electrician replace the obsolete outlet.

If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.

14 TFT-LCD TV

Operation

-In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an example to help you with the TV operation.

-There are several options you might need to set up in order for your TV to work properly. Read the instructions that follow.

Switching On/Off the TV set

1. First, connect power cord correctly.

2. Select the viewing source by using INPUT button on the remote control.

3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

4. If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

Note:

If the TV in power on , the screen show information according the type of input signal . the information will disappear. If there is no signal, the No signal will display on the left bottom of the screen.

Choose the Menu Language

When you start using your set for the first time, you must select the language which will be used for displaying menus

and indications.

1 Press the MENU button and then use / button to select the

Settings menu.

2 Press the button and then use / button to select Menu

Language.

3 Press the button and then use / button to enter the list of

available language. English Spanish or French

4 Select your language with the / button and press the OK

button to confirm you selection.

5 When you are satisfied with your choice, press the EXIT button

to return to normal viewing or press / MENU button to return to the

previous menu.

Choose the Input Source

- Change the picture source so you can watch your TV, cable TV, VCR, DVD, or any other devices that are connected to your TV.

1. Press MENU button and then use / button to select the Video menu. 2 Press the button and then use / button to select Select Source option. 3 Press the button and then use / button to select the available Source.

TV, CVBS,S-Video, YPbPr, HDMI, VGA,VGA-YPbPr

4. Press the OK button to confirm. 5 When you are satisfied with your choice, press the EXIT button

to return to normal viewing or press / MENU button to return to the previous menu.

You can also press the INPUT button repeatedly to select the desired source.

Owner s Manual 15

Channel menu

This TV set has two methods to set channels, which are respectively Scan Channel, Add Channel. In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV

set to set channel.

Note

Make sure you are in an open environment where there is a good signal while scanning so that it is able to find all channels more easily.

Scan Channel

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the All Channel List.

Note : the Channel menu will be only operated in normal TV mode.

1 Press the MENU button and then use / button to select the

Channels menu.

2 Press the button and then use / button to select Scan Channel.

3 Press the button and then use / button to Select Cable or

Antenna mode.

4 Press the OK button to start searching channel.

While it is scanning for channels, at any point, you can interrupt the scanning

process by pressing the Stop Scan button. Those channels have been scanned

would be stored in the available channel table.

5 After you finish scanning for available channels, you may select DONE to

return the display window ..

Operation

When Antenna is selected, the TV will detect antenna signals and will search for antenna TV (NTSC and ATSC) channels available in your local area. When Cable is selected, the TV will detect cable company supplied signals and will search for cable TV (NTSC, ATSC, QAM modulated) channels available in your area.

Add Channel

If excessive channel signals of unwanted programs are received in local area, manual search function is recommended.

1 Press the MENU button and then use / button to select the Channels menu.

2 Press the button and then use / button to select Add Channel.

3 Press the button and then use digital buttons to input channel number

you want to add channel.

4 Press the OK button to confirm.

5 When you are satisfied with your choice, press MENU button to return

to the previous menu.

6 Press EXIT button to return to TV viewing or press button to

return to the previous menu.

Note Make sure your TV is placed in an open environment where is a good signal while

scanning so that it is able to find all channels more easily. If user does not proceed scan channel in advance, it will take Antenna as the default source.

/ MENU

16 TFT-LCD TV

Operation

Channel menu

Favorites

You can create your own Favorite List. when a channel is highlighted and then you can add or delete the channel

to/from the Favorite List.

You can skip some channel;

1 Press the MENU button and then use / button to select the

Channels menu.

2 Press the button and then use / button to select Favorites.

3 Press the button to call up favorites list menu.

4 Use / / / button to select option, and then use the OK button to confirm.

5 When you are satisfied with your choice, press / MENU button to return to the

previous menu or Press EXIT button to return to TV viewing.

Channel list

1 Press the MENU button and then use / button to select the

Channels menu.

2 Press the button and then use / button to select Channel list.

3 Press the button to call up Channel list menu.

4 Use / / / button to select option, and then use the OK

button to confirm.

5 When you are satisfied with your choice, press / MENU button to

return to the previous menu or Press EXIT button to return to

TV viewing.

Owner s Manual 17

Video menu

The TV menu gives you an overview of the menus you can select.

Note: Depending on the input signal, one or more menu items may not be selectable.

1 Press the MENU button and then use / button to select the Video menu.

2 Press the button and then use / button to select the desired items.

3 Press the button and then use / button to adjust the setting.

4 Press the OK button to confirm.

5 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Select Source Select the video input source. Picture Settings Adjust the picture setting. Aspect Ratio Select the display aspect ratio.

Color temperature

This will increase or decrease Warm (red) and Cool (blue) colors to suit personal preferences.

Back Light Adjust the backlight value. Screen Adjustment Adjust the picture position.

Picture Settings

Operation

1 Press the button and then use / button to select the Picture Settings. 2 Press the button and then use / button to select the desired item. 3 Press the OK button to confirm. 4 Press the button and then use / button to adjust the setting.

5 Press the OK button to confirm.

6 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Preset

This provides the pre-defined images settings, There are standard, vivid, movie, Pro and custom modes provided for usage. Standard: normal mode.

Vivid: mode of watching the movement of picture. Mild: the effect of the picture is soft. Custom: picture effect which you favorite.

Pro: Professional mode, it`s can be used in VGA source.

Contrast

This will adjust the intensity of bright parts in the picture but keep the dark parts unchanged.

Brightness

This will adjust the light output of the complete picture, which will mainly affect the darker areas of the picture.

Hue

Allows you to select the color mix (Hue) of the picture.

Saturation

This will adjust the saturation level of the colors to suit your personal preference.

Sharpness

This will adjust the sharpness of fine details in the picture.

Noise Reduction

Automatically filters out and reduces the image noise and improves picture quality when receiving weak video signals.

Note:

Only when the item of mode is custom , the Contrast Brightness Hue Saturation Sharpness can be set by user . In other mode the value of them are preset by program .

18 TV LCD-TFT

Operation

Video menu

Aspect Ratio Control

- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format.

- Note: If a fixed image is displayed on the screen for a long time, it image may become imprinted on the screen and remain visible.

1 Press the MENU button and then use / button to select the Video menu.

2 Press the button and then use / button to select the Aspect Ratio.

3 Press the button and then use / button to select the desired item. 4 Press the OK button to confirm.

5 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

1:1 Mode

Select to display the picture at the center with the same resolution as the input source.

Normal

Select to display the picture to fit the screen without distorting the aspect ratio.

Full

Select to display the picture to fill the screen.

Panoramic

Select to display the picture on the screen by linear scaling the center 50 % area and increase the scaling factor at 25% left and right sides.

Zoom

Select to display the enlarged picture.

You can also press the ARC button to select Aspect Ratio.

Notes

In VGA mode, only 1:1 Mode, Full, Normal can be selected.

Owner s Manual 19

Video menu

Screen adjustment

1 Press the MENU button and then use / button to select the Video menu.

2 Press the button and then use / button to select the Screen Adjustment.

3 Press the button and then use / button to select option.

4 Press / button to adjust the setting and press OK button.

5 When you are satisfied with your choice, press or MENU button to

return to the previous menu or press the EXIT button to return to TV viewing.

Operation

Horizontal: Vertical: Phase: Auto Sync:

Adjust the position of the picture left and right. Adjust the position of the picture up and down. Adjust the distortion effects of horizontal wavy lines or ripples.

Adjust the display position and phase of the picture automatically.

Color Temperature

This will increase or decrease Warm (red) and Cool(blue) colors to suit personal preferences. Select Cool to give the white colors a blue tint, Native to give the white colors a neutral tint, Warm to give the white colors a red tint.

Cool: Select to give the white colors a bluish tint. Native: Select to give the white colors a native tint. Warm: Select to give the white colors a reddish tint.

1 Press the MENU button and then use / button to select the Video menu.

2 Press the button and then use / button to select the Color Temperature.

3 Press the button and then use / button to select option.

4 press OK button.

5 When you are satisfied with your choice, press or MENU button to

return to the previous menu or press the EXIT button to return to TV viewing.

Back Light

1 Press the MENU button and then use / button to select the Video menu.

2 Press the button and then use / button to select the Back Light.

3 Press the button and then use / button to select option.

4 press OK button.

5 When you are satisfied with your choice, press or MENU button to

return to the previous menu or press the EXIT button to return to TV viewing.

Bright Room: Select the bright backlight setting. Dark Room: Select the dark backlight setting. Medium Room: Select the native backlight setting.

20 TFT-LCD TV

Audio menu

Bass, Treble and Balance Setup

1 Press the MENU button and then use / button to select the Audio menu.

2 Press the button and then use / button to select Bass, Treble & Balance.

3 Press the button and then use / button to select desired item.

4 Press the button and then use / button to adjust the setting.

5 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Bass

This will adjust the bass output level.

Treble

This will adjust the treble output level.

Balance

This will adjust the output of the right and left speakers to obtain the best stereo reproduction for your listening position.

Operation

MTS

- This TV can receive MTS stereo programs and SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one.

- When having selected SAP button on the remote control, this TV can only receive the signal when the TV station transmits the proper signals.

- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

- Select Mono if you want to listen to mono sound during stereo/SAP broadcasting.

- Stereo or SAP can be received in a Analog channel.

1 Press the MENU button and then use / button to select the Audio menu.

2 Press the button and then use / button to select MTS.

3 Press the button and then use / button to select desired item.

4 Press OK button to confirm.

5 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

You can also use the SAP button to select your desired MTS mode in a analog signal. Each time you press the SAP button, Mono, Stereo, or SAP appear. If other languages are available on the digital signal, select them with the SAP button.

Owner s Manual 21

Audio menu

Digital Audio Language

(Only selectable with digital broadcast signals)

1 Press the MENU button and then use / button to select the Audio menu.

2 Press the button and then use / button to select Digital Audio Language.

3 Press the button and then use / button to select desired language.

4 Press OK button to confirm.

5 When you are satisfied with your choice, press or MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Operation

TV Speaker

1 Press the MENU button and then use / button to select the Audio menu.

2 Press the button and then use / button to select TV Speaker.

3 Press OK button to set as ON or OFF.

4 When you are satisfied with your choice, press or MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Mute

When you need to pay attention to surrounded sounds, or there is a telephone calling you or there are some guests visiting you, the sound elimination (mute) function is very convenient.

1 Press the MUTE button on the remote control and " "

type face will display on the screen. At this time, the sound of the TV set is turned off.

2 If you want to recover the sound, press the MUTE

button again or directly press VOL+/- button.

22 TV LCD-TFT

Settings Menu

Timer setting

The timer setting will only work if the TV set is turned on or in standby. Switch on/off automatically at the time you presetting.

1 Press the MENU button and then use / button to select the Settings menu.

2 Press the button and then use / button to select the Timers.

3 Press the button and then use / button to select Timer.

4 Press the button to enter the Timer Setting menu.

5 Press / button to select the desired day. 6 Press the OK button to confirm, if to cancel the select, Press the OK button.

7 Press / button to select the Start Time or Stop Time, and press OK button

to enter the setting submenu.

8 Press / button to button move cursor.

9 Press / button or the digits button to setting the desired time.

10 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Note

1. Please aware of the Stop Time must follow with Start Time. The two settings

must be setting cooperatively. 2 .Please kindly be aware of the Timer Setting will take effective only after you finish setting and shut off the TV. Then the system will start to final countdown. Otherwise, the function will be ineffective.

Operation

Sleep Timer Setting

The sleep timer automatically shuts off the TV after a preset time (from 30 to 120 minutes).

1 Press the MENU button and then use / button to select the Time menu.

2 Press the button and then use / button to select the SleepTimer.

3 Press the button and then use / button to select the number of minutes.

Select OFF, 30Min, 60Min, 90Min, 120Min.

When the number of minutes you want is displayed on the screen, press the OK

button. The time begins to count down from the number of minutes selected.

4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

5 To cancel the set sleep timer:

Press the / button to select OFF.

You can use the SLEEP button also to select quickly the sleep timer.

Owner s Manual 23

Settings Menu

Date & Time setting

1 Press the MENU button and then use / button to select the Settings menu.

2 Press the button and then use / button to select Date & Time.

3 Press the button to enter the date & time setting menu.

4 Press the / / button to select the desired option.

5 Press the OK button to confirm or enter the submenu. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Today`s Date and Current time setting

1 Press the / button to select the Today`s Date & Current Time.

2 Press the OK button to confirm.

3 Press the button to select desired item and then use / button or

the digits buttons to adjust the setting.

2 Press the OK button to confirm.

4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Operation

Time zone setting

This function allows you to select your local time zone. Broadcasted time information will correct the clock display for your local time.

1 Press the / button to select the Time Zone.

2 Press the OK button to confirm.

3 Press the button and then use / button to adjust the setting.

4 When you are satisfied with your choice, press /MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Press the button and then use / button to select your viewing area time zone: Newfoundland, Atlantic, Eastern, Central, Mountain, Pacific, Alaska, Hawaii

or Samoa.

Daylight Saving setting

Daylight saving time is automatically set by specially broadcasted signals. This menu item allows you to disable the automatic setting of daylight saving time. This is useful if you live in an area or state where daylight saving is not applied, but you receive channels from other areas where daylight saving signals are broadcasted.

1 Press / button to select Adjust for Daylight Saving item. 2 Press the button to select On for automatic clock correction for daylight saving time, based on specially broadcasted signals. Select Off to disable automatic clock correction based on the specially broadcasted signals.

24 TFT-LCD TV

Settings Menu

Closed Captions

Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs.

Using Closed Captions

Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance. Its possible to caption a live program by using a process called real-time captioning, which creates captions instantly. Real-time captioning is normally done by professional reporters using a machine shorthand system and computer for translation into English. Captioning is an effective system for the hearing-impaired, and it can also aid in teaching language skills.

CC Activation

1. Press the MENU button and then use / button to select the Settings menu.

2. Press the button and then use / button to select Closed Caption.

2. Press the / button to select the CC Activation.

3. Press the OK button to select On or Off mode.

Operation

4. When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Caption Service

This allows you to configure the way you choose to view the digital captioning.

1. Press the MENU button and then use / button to select the Settings menu.

2. Press the button and then use / button to select Closed Caption.

2. Press the button and then use / button to select Caption Service.

3. Press the button and then use / button to select caption: CC1, CC2,

CC3, CC4, Text1, Text2, Text3, or Text4.

4. When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

Digital Caption Service (In DTV mode)

This allows you to configure the way you choose to view the digital captioning. Select one of the digital service channels made available by the captionprovider. There are 6 standard services. Caption Service 1 is designated as the Primary Caption Service. This service contains the verbatim, or near-verbatim captions for the primary language being spoken in the accompanying program audio. Caption Service 2 is designated as the Secondary Language Service. This service contains captions in a secondary language which are translations of the captions in the primary Caption Service. The other service subchannels are not pre-assigned. It is up to the discretion of the individual caption provider to utilize the remaining service channels.

1. Press the MENU button and then use / button to select the Settings menu.

2. Press the button and then use / button to select Closed Caption.

2. Press the button and then use / button to select Digital Caption Service.

3. Press the button and then use / button to select caption: CS1, CS2, CS3, CS4,

CS5, CS6.

4. When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Owner s Manual 25

Digital Caption Option (In DTV mode)

This allows you to modify how digital captions are displayed on your TV. Select from the following options to change the visual characteristics of your TV`s digital captioning.

- Customize the DTV/CADTV captions that appear on your screen.

1. Press the MENU button and then use / button to select the Settings menu.

2. Press the button and then use / button to select Closed Caption.

3. Press the button and then use / button to select Digital Caption Option.

4. Press the button to enter the submenu.

5. Use / / / button to customize the Style, Font, etc., to your preference.

6. Press the OK button to confirm.

7. When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Text Style: Select the caption text style.

Color(Text): Set the caption text color.

Opacity(Text): Select the caption text opacity.

Size(Text): Select the caption text size.

Align(Text): Select the caption text-align position.

Edge Color: Set the caption edge color.

Style: Select the caption edge style.

Background: Set the caption background color.

Opacity(Background): Select the caption background opacity.

Frame Color: Set the caption frame color.

Opacity(Frame): Select the caption frame opacity.

Operation

Caption Preference (In DTV mode)

1. Press the MENU button and then use / button to select the Settings menu.

2. Press the button and then use / button to select Closed Caption.

3. Press the / button to select the Caption Preference.

4. Press the button and then use / button to the desired option.

5. Press the OK button to confirm.

6. When you are satisfied with your choice, press MENU button to return to the previous menu or press the EXIT button to return to TV viewing.

Always Caption Service: Always to turn on analog caption service.

Always Digital Caption Service: Always to turn on digital caption service.

Automatic: Automatically turn on the analog or digital caption service depends on the source signal.

26 TFT-LCD TV

Operation

Parental Control

Parental Control can be used to block specific channels, ratings and other viewing sources.

The Parental Control Function is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1. Set ratings and categories to be blocked.

2. Specify a password

3. Enable the lock

Parental Control rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.

Ratings for Movies previously shown in theaters:

Movie Ratings :

G (General audience) PG (Parental guidance suggested) PG-13 (Parents strongly cautioned) R (Restricted) NC-17 (No one 17 and under admitted) X (Adult only) If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

TV-Y (All children)

TV-Y7 (Children 7 years older) TV-G (General audience) TV-PG (Parental guidance suggested) TV-14 (Parents strongly cautioned) TV-MA (Mature audience only)

TV Rating Children: ALL (Age) (applies to TV-Y, TV-Y7) FV (Fantasy Violence) (applies to TV-Y7)

TV Rating General: ALL (Age) (applies to TV-G, TV-PG, TV-14, TV-MA) D (Dialogue - sexual dialogue) (applies to TV-PG, TV-14) L (Language - adult language) (applies to TV-PG, TV-14, TV-MA) S (Sex - sexual situations) (applies to TV-PG, TV-14, TV-MA) V (Violence) (applies to TV-PG, TV-14, TV-MA)

Owner s Manual 27

Parental Control

- Set up blocking schemes to block specific channels, ratings, and external viewing sources.

- A password is required to gain access to this menu.

1. Press the MENU button and then use / button to select the Settings menu.

2. Press the button and then use / button to select the Parental Control.

Then, press the button, and input the password, then press OK .

The TV is set up with the initial password 0-0-0-0-0-0 .

3. Use the / button to choose from the right Lock Menu options.

Once the option is selected, change the settings to your preference.

Password: Change the password by inputting a new password twice.

Rating:

1. P ress / button to select Rating item.

2. Press the OK button to select On or Off.

Note:

if the Rating is setting as Off, the change of the USA-TV Rating, USA-Movie Rating, CA Eng Rating and CA Fren Rating will be no useful.

Operation

USA-TV Rating

The Parental control will automatically block certain categories that are

more restrictive . For example, if you block TV-Y category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the young adult group will be blocked (TV-Y, TV-Y7, TV-G, TV-PG, TV-14, and TV-MA). The sub-ratings (D, L, S, V) work together similarly.

1 Press / button to select USA-TV Rating item. 2 Press the button and then use / button to .

select one of these Ratings

3 Press the OK button to set block or unblock. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

USA-Movie Rating Movie Rating (MPAA): Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.

1 Press / button to select USA-Movie Rating item. 2 Press the button and then use / button to select the rating. 3 Press the ok button to set block or unblock. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

28 TFT-LCD TV

Parental Control

Canada English Rating

To select the block programs by the Canada-English rating.

1 Press / button to select CA Eng Rating item.

2 Press the button and then use / button to select the rating. 3 Press the ok button to confirm. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Exempt C Children C8+ Children eight years and older G General Programming, suitable for all audiences PG Parental Guidance 14+ Viewers 14 years and older 18+ Adult Programming

Canada French Rating

To select the block programs by the Canada-French rating.

Operation

1 Press / button to select CA Fren Rating item. 2 Press the button and then use / button to select the rating. 3 Press the ok button to confirm. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

E Exempt G General 8 ans+ 8+ General - Not recommended for young children 13 ans+ Programming may not be suitable for children under the age of 13 16 ans+ Programming is not suitable for children under the age of 16 18 ans+ Programming restricted to adults

Block Unrated Setting

To select to block unrated channels.

1 Press / button to select Block Unrated Setting item.

2 Press the button. 3 Press the ok button to select On or Off. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Channel Locks

To select channels to block.

1 Press / button to select Channel Locks item.

2 Press the button and then use / button to select Lock or Unlock the channel. 3 Press the ok button to confirm. 4 When you are satisfied with your choice, press MENU button to return to

the previous menu or press the EXIT button to return to TV viewing.

Owner s Manual 29

Quick Program View

This function enables quick swap to the last watched program.

1 Suppose the channel number you used just now is 8 and the channel number you are

using is 18 (as shown in the figure).

If you want to return to the last watched program channel 8, you can simply press the

Q.View button.

If you want to return to channel 18, press the button again. Use this function, you can

easily change between the channel you are using and the channel you used last time.

Operation

30 TV LCD-TFT

Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in six different modes: TV, VCR, CABLE, DVD, SETBOX or AUDIO Pressing the corresponding button on the remote control

allows you to switch between these modes, and control whichever piece of equipment you choose.

Note

The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.

Controller Operation

To control a device using the Controller

1. Program the Controller to work with your device.

2. Changing device mode by pressing the SELECT key. Default device is TV. When press SELECT key, current device led will be on. Keep pressing SELECT key to choose a device, the loop is: TV DVD VCR STB Cable Audio - TV. When device is set, related device LED will be on for 5 seconds and then be off.

3. Aim the remote at the device.

4. Press the POWER button to turn the device on.

5. Use the other Controller buttons to operate the device. Device LED will blink if user presses any key (if the key has data in current mode.). If the key has no data, then LED will not blink.

6. Default init status: TV/Haier 001 code.

7. Bulb key to control the flash light.

Programming the Controller

The Controller is factory-programmed to support up to 600 code sets. There are two ways to program the Controller: Selecting a brand code for the device you wish to operate, and then entering that code manually into the Controller. Using the Power Scan feature to find device codes automatically. The two programming methods are described in the following sections.

Operation

Manually Programming the Controller

1. Using SELECT key to choose the device you want to program.

2. While Press and holding OK key, press SELECT key, and device LED will be ON. Keep the status for about 5 seconds, release both keys and then LED will blink twice per second, indicating that the Controller is ready for programming.

3. Led will blink once when you enter a digit key, indicating the digit key is programmed. If 3 digits are programmed successfully, device LED will be ON for about 3 seconds and then blink twice per second. Then User now can: a) Try to operate the device by using POWER or PLAY keys. If operation can be done, press OK to save current 3-digits code and exiting manually programming mode. b) Return to beginning of step 3. Reprogram the controller.

5. If user's input is incorrect, LED will blink 12 times in 3 seconds. And then keep twice per second blink, user now can return to step 3 and re-program the device.

6. Within 10 seconds, user should enter the 3-digit brand code corresponding to your device. If time out or any key other than POWER PLAY and digits is pressed, LED will be off and manually programming process is exit.

7. Fast Programming Haier default TV code set. Press and holding the EXIT key and then press SELECT key for 5 seconds, default Haier code set (001) will be programmed to the controller.

Manually scan mode

With manually scan programming, the Controller tests all the codes available in the code set data base and assign the correct one for the selected device. To manually-scan program the Controller:

1. Manually turn OFF the device for manually scan mode. (TV, VCR, DVD, STB, cable box or audio equipment).

2. Press SELECT key to choose the device you wish to program. While Press and holding OK key, press the SELECT key and device LED will be ON. Keep the status for about 5 seconds, release both keys and then LED will blink twice per second, indicating that the Controller is ready for programming.

3. Press and release the CH+/CH- key. The LED blinks 10 times per seconds, indicating that the Remote is in manually scan mode.

4. Press CH+/CH- key repeatedly until the device switches ON (CH+ key conducts a upward search while the CH- key conducts a downward search in the code set database).

5. When the device turns ON, press and release the OK key to program the Controller with the new code, saving the code and exit. To exit without programming, press any key other except CH+/CH- and OK. LED will be off after manually scan mode is exit.

6. If the device responds, no further programming is required. If the device does not respond, repeat step 1 through 5.And searching will start from current code set. If no key was pressed in 30 seconds, manually scan mode will be automatically exit.

7. After searching the entire data base, this mode will be automatically exited and led will blink for 3 times.

Owner s Manual 31

Setting Up Your Remote Control

Automatic Scan Programming the Controller

To automatic scan program the Controller:

1. Manually turn OFF the device you wish to power scan. (TV, VCR, DVD, STB, cable box or audio equipment).

3. Press and release the Mute key to enter automatic scan mode. And the remote will automatically sending power codes to the device.

4. When the device turns ON, press OK key to program the Controller with the new code, saving it and exit. To exit without programming, press any key other except OK key.

5. If the device responds, no further programming is required. If the device does not respond, repeat steps 1 through 4. And search will start from current code set.

6. After searching the entire data base, this mode will be automatically exited and led will blink for 3 times.

Punch-Through Features

The Controller provides two punch-through features that allow users to control TV volume and DVD or VCR operation while the Controller is in another device mode control certain features of another device.

Operation

Volume Punch-Through:

The TV Volume/Mute punch-through feature allows you to control the volume and mute function of your TV while the Controller is in another device mode. The feature is applicable for all devices and brands that do not use the volume control buttons for other purposes.

Transport Key Punch-Through:

The DVD or VCR transport key punch through feature lets you control the PLAY, STOP, PAUSE, REWIND, FF and RECORD functions of your DVD or VCR while the Controller operates in other modes. The feature is applicable for all devices and brands that do not use the transport keys for other purposes.

Protection mode:

1. While press and holding OK, press AUTO key for 5 seconds to enter protection mode. In this mode, all the above programming methods will be invalid.

2.To exit protection: While press and holding OK, press AUTO key. Current device related LED remains ON and then release OK and AUTO. Input three digit password “8 8 8”, LED turns off and protection mode is ended. If error password is input or no password input in 10 seconds, LED blinks three times and then turns off. Protection mode will remain.

Display mode:

1.To enter display mode, while press and holding OK key, press the SELECT key and device LED will be ON, keep the status for about 5 seconds. Release both keys and then LED will blink 2 times per second, indicating controller is for programming.

2.Sequence press 9, 8, 0 to enter display mode. And LED is off now.

3.Press digit 1 key to get the first digit of current code set. For example, if the first digit of code set is 1, so then led will blink once and remains OFF. Digit 0 in code set will not be displayed. Blink twice per second.

4.Press digit 2 key to get the second digit of current code set. For example, if the second digit of code set is 3, so then led will blink three times and remains OFF. Blink twice per second.

5.Press digit 3 key to get the third digit of current code set. Blink twice per second.

6.Only digit 1, 2, 3 are valid in this mode. And the sequence is not fixed. You can repeat, if you don't remember clearly.

7.Controller will not send out data in this mode if user presses any keys other than digit 1, 2, 3. And this can be regarded as no key pressed.

8.If no key was pressed in 10 seconds or any key other than digit 1, 2, 3 is pressed display mode is ended.

ready

32 TV LCD-TFT

Remote Control Codes

NO. Brand Code

Haier

A Mark

Action

Admiral

Advent

Aiko

Aiwa

Akai

Amtron

Anam

Anam National

AOC

Apex

Audiovox

Bell & Howell

Benq

Broksonic

Carver

CCE

Centurion

Citek

Citizen

Classic

Colortyme

Contec Cony

Contec/Cony

Craig

Crosley

Crown

CTX

Curtis

Curtis Mathes

Daewoo

Daytron

Denon

Dimensia

Dumont

Electrohome

Emerson

Envision

Fisher

Fujitsu

Funai

Goldstar

Gradiente

Granada

Grundig

Hallmark

Harman Kardon

Hisense

Hitachi

Infinity

Janeil

JBL

JC Penney

ensen

JVC

Kawasho

Kenwood

Kloss Novabeam

KTV

Lloyds

Loewe

Logik

Luxman

LXI

Magnasonic

Magnavox

Majestic

Marantz

Megatron

001 002 003 004 005 006 007 008 009 010 011 085 134 108 071 093 099 118 127 130 131 147 079 047 104 105 123 082 106 072 082 110 073 074 075 104 112 117 134 140 000 157 015 016 082 108 140 144 071 084 118 131 051 037 038 104 106 118 138 146 153 118 077 143 073 075 079 082 089 092 138 104 123 073 075 105 116 118 125 127 139 106 108 078 082 082 106 108 114 119 125 138 118 153 082 087 119 134 056 104 070 073 075 084 089 092 102 105 112 117 118 125 127 134 135 148 153 155 073 074 075 079 092 104 110 112 117 134 135 140 144 073 075 092 114 117 134 140 145 070 155 073 091 072 073 075 080 104 105 117 134 073 075 078 081 082 083 084 092 096 103 104 105 106 108 114 117 119 125 129 130 131 134 139 144 146 073 075 105 112 052 084 115 123 124 133 083 082 083 106 108 165 066 067 070 072 073 075 168 086 104 106 110 113 116 117 125 126 127 128 134 144 149 154 155 073 074 075 078 080 092 104 105 109 112 117 134 135 137 105 122 123 134 126 134 073 075 104 104 151 041 042 058 059 068 073 075 078 101 117 126 127 131 134 140 145 087 153 094 087 153 070 073 074 075 168 086 089 092 104 112 113 125 126 127 134 149 155 073 075 105 129 163 166 012 031 036 078 086 103 122 125 126 073 075 112 123 073 075 080 104 105 112 116 139 082 094 110 082 092 106 108 112 117 134 074 137 139 087 071 142 073 075 070 075 084 087 104 118 127 149 153 155 104 105 131 140 017 073 075 080 087 104 105 112 114 117 118 119 126 131 153 071 073 075 087 105 112 116 117 118 153 075

NO. Brand Code

Memorex

MGA

Mitsubishi

Montgomery Ward

Motorola

MTC

Multitech

Multivision

NAD

NEC

Nikko

Noblex

Onwa

Optimus

Optonica

Orion

Panasonic

Philco

Philips

Pioneer

Portland

Price Club

Prima

Prism

Proscan

Proton

Quasar

100

Radio Shack

101

Radio Shack/Realistic

102

RCA

103

Realistic

104

Runco

105

Sampo

106

Samsung

107

Sansui

108

Sanyo

109

Scott

110

Sears

111

Sharp

112

Signature

113

Signature 2000

114

Sony

115

Soundesign

116

Starlite

117

Supre-Macy

118

Sylvania

119

Symphonic

120

Tandy

121

Tatung

122 123

Technics

124

Techwood

125

Teknika

126

Telecaption

127

Telefunken

128

Toshiba

129

Totevision

130

Ultra

131

Uniden

132

Universal

133

Video Concepts

134

Vidikron

135

Wards

136

Wallmart

137

White Westinghouse

138

Yamaha

139

Zenith

140

RePlay

071 074 075 084 104 073 074 075 080 105 049 073 074 075 080 104 105 112 117 134 071 072 093 073 074 075 089 104 112 118 125 140 082 088 075 101 072 073 074 075 105 112 116 117 139 075 079 140 137 082 106 101 093 096 130 146 159 167 023 032 033 034 072 086 087 108 110 113 126 127 128 140 072 073 074 075 078 080 087 104 105 112 114 117 118 119 131 140 145 153 160 161 029 030 072 073 078 080 087 118 153 045 073 075 101 110 111 116 117 073 074 075 079 092 104 112 117 134 135 089 135 142 152 086 070 127 149 154 155 073 075 078 104 105 117 119 127 134 138 053 063 064 072 086 110 114 126 128 084 106 108 110 118 120 124 127 132 134 155 070 073 075 078 082 084 092 164 060 065 070 072 073 074 075 080 102 106 110 111 113 116 117 125 127 128 134 148 149 154 155 084 155 091 039 073 075 092 110 112 117 043 048 054 057 062 073 074 075 078 080 089 092 097 104 112 117 118 125 131 134 139 022 096 120 073 084 115 124 073 075 078 082 083 106 108 117 130 134 070 073 075 080 083 084 095 104 106 115 118 124 127 133 134 149 153 155 013 028 035 073 075 078 092 093 120 131 132 134 139 141 071 115 132 158 018 026 098 100 121 123 134 073 075 082 083 104 106 117 119 129 082 094 044 046 069 073 075 080 087 104 105 112 114 117 118 119 140 153 081 082 095 108 093 118 072 110 138 086 126 128 073 075 086 105 118 071 073 074 075 078 079 082 083 089 092 106 108 112 116 117 119 134 137 140 143 153 090 139 162 019 021 024 025 027 084 089 090 115 125 133 150 092 127 140 121 168 106 118 153 070 071 073 074 075 080 081 083 168 087 104 112 113 117 118 119 120 125 127 131 153 155 055 051 107 104 112 134 135 140 144 073 074 075 080 112 119 139 140 050 055 061 071 073 091 109 121 140 156

Operation

Owner s Manual 33

Remote Control Codes

Operation

DVD

NO. Brand Code

Aiwa

Apex

Audiovox

Blaupunkt

BOSE

Broksonic

Clarion

Classic

Daewoo

Denon

Emerson

Fisher

Funai

Go Video

GPX

Harman Kardon

Hitachi

Irradio

JVC

Kenwood

Koss

Magnavox

Marantz

Memorex

Mintek

Mitsubishi

NAD

Nakamichi

Norcent

Onkyo

Oritron

Panasonic

Philips

Pioneer

Proscan

Qwestar

RCA

Sampo

Samsung

Sansui

Sanyo

Sharp

Sherwood

Sony

Sylvania

Techwood

Toshiba

Yamaha

Zenith

073 044 000 001 003 004 016 028 029 030 074 078 062 071 045 046 047 079 080 075 095 096 048 049 050 076 049 064 005 051 102 068 070 052 066 065 067 092 007 010 011 012 013 097 100 093 020 035 085 087 053 088 089 090 091 048 081 054 055 056 082 086 057 008 036 037 002 009 021 022 023 043 027 032 005 099 057 005 024 038 058 006 017 033 041 060 059 063 014 031 061 015 018 034 039 049 072 077 083 019 026 040 042 084 098 069 094

VCR

NO. B ran d Cod e 1 2 3 4 5 6 7 8 9 10 11 12

Admiral

Aiko

Aiwa

Akai

Audiovox

Bell & Howell

Broksonic

Calix

Canon

Capehart

Carver

CCE

Citizen

Colortyme

Craig

Curtis Mathes

Daewoo

Daytron

Denon

Dimensia

Electrohome

Emerson

Fisher

Fuji

Funai

Garrard

Go Video

Goldstar

Gradiente

Harman Kardon

Harwood

Hitachi

JBL

JC Penney

Jensen

JVC

Kenwood

KLH

Kodak

Lloyds

Logik

LXI

Magnasonic

Magnavox

Marantz

Matsushita

Memorex

MGA

MGN

Minolta

Mitsubishi

Montgomery Ward

Motorola

MTC

Multitech

NEC

Nikko

Noblex

Olympus

Optimus

Optonica

Orion

Panasonic

Pentax

Philco

Philips

Pioneer

Portland

Proscan

Precision

Proton

Quasar

Radio Shack

Radio Shack/Realistic

Radix

RCA

073 074 101 056 055 044 045 068 069 080 093 051 048 023 049 106 051 053 054 067 083 060 110 056 059 050 051 052 056 095 046 096 050 051 059 085 090 105 043 046 050 053 054 077 079 112 014 052 055 056 067 083 102 067 083 102 088 043 112 051 090 044 049 051 052 053 055 061 069 087 090 106 048 089 105 045 053 055 095 055 040 043 050 053 054 070 079 081 087 112 021 024 026 028 034 079 081 085 086 046 051 079 090 092 055 090 046 110 059 025 036 037 057 058 065 068 070 088 098 046 047 048 049 050 051 053 054 057 058 059 060 065 079 085 088 090 057 058 068 000 019 046 047 048 068 071 087 088 046 047 048 068 071 077 059 051 053 051 077 095 105 059 085 051 085 090 102 008 053 054 060 064 085 110 046 047 048 053 060 077 092 110 053 033 048 050 051 053 055 064 073 074 088 090 091 097105 061 069 079 057 058 065 088 003 005 006 057 058 061 069 071 090 073 074 053 073 074 050 085 050 055 059 046 047 048 068 071 077 092 051 050 053 051 073 074 090 094 062 087 090 106 002 004 009 020 053 054 066 085 090 105 057 058 065 070 077 088 053 054 060 088 106 017 018 053 042 060 062 110 047 057 071 075 078 104 067 083 043 112 102 085 053 054 090 051 062 074 090 048 050 051 053 054 055 062 073 051 012 016 043 044 050 053 057 058 065 070 078 079 088 107 108 112

34 TFT-LCD TV

Remote Control Codes

NO. Brand Code

Realistic

Ricoh

Runco

Samsung

Sansui

Sanyo

Scott

Sears

Sharp

Shintom

Signature

Signature 2000

Singer

Sony

STS

Sylvania

Symphonic

Tandy

Tashiko

Tatung

Teac

Technics

Teknika

100

Toshiba

101

Totevision

102

Tivo

103

Unitec

104

Unitech

105

Vector Research

106

Video Concepts

107

Wards

108

White Westinghouse

109

XR-1000

110

Yamaha

111

Zenith

112

Action

113

048 050 051 052 053 054 055 062 073 074 079 090 094 097 105 072 076 064 029 031 035 039 050 052 079 095 047 068 071 085 022 048 050 089 097 105 049 052 061 090 048 051 053 057 058 065 077 088 089 090 097 105 015 062 073 074 091 094 101 045 058 059 085 073 074 097 101 053 059 072 076 085 007 041 045 063 080 082 084 098 099 053 065 030 032 053 054 055 060 061 110 055 077 095 105 048 051 068 055 068 107 053 066 051 053 055 090 010 011 052 057 061 069 100 102 105 109 050 051 090 111 095 050 046 047 052 077 046 047 052 069 077 050 051 052 053 055 057 058 059 062 065 073 074 079 090 091 094 105 108 110 095 053 055 059 046 047 048 068 077 027 038 045 064 072 076 090 093 102

SETBOX

NO. Brand Code

Alphastar

Chaparral

DIRECTV

DISH NETWORK

Drake

Echostar

Express Vu

Fujitsu

General Instruments

Hitachi

Hughes

Janeil

JVC

Mitsubishi

Panasonic

Philips

Proscan

Radio Shack

RCA

Realistic

Samsung

Sony

Star Choice

Star Trak

STS

Toshiba

Uniden

Zenith

CABLE

NO. Brand Code

ABC

Archer

Cableview

Contec

Eastern

Gemini

General Instruments

Hamlin

Hitachi

Jerrold

Magnavox

Motorola

Movie Time

NEC

NSC

Oak

Panasonic

Philips

Pioneer

Proscan

RCA

Realistic

Samsung

Scientific Atlanta

Signature

Sprucer

Standard Component

Starcom

Stargate

Tocom

United Cable

Universal

View Star

Zenith

028 024 001 039 001 026 030 027 026 030 022 004 032 033 018 019 023 023 036 022 015 002 040 005 011 000 012 032 033 018 019 010 032 033 014 006 028 007 034 035 037 038 031 021 020 008 029 016 017 009 013 022

000 001 002 030 006 007 003 034 035 000 012 013 000 032 036 037 038 040 044 000 000 012 015 016 026 030 032 017 031 039 033 039 034 041 027 029 008 009 010 011 013 017 018 019 020 021 022 000 003 029 032 006 022 002 023 024 025 000 029 042 043 012 030 012 001 015 030 004 006 007 017 034 039 028

Operation

Owner s Manual 35

Remote Control Codes

AUDIO

Operation

Receiver/Tuner

NO. Brand Code

Aiwa

BOSE

Carver

Curtis Mathes

Denon

Fisher

Gradiente

Harman Kardon

Hitachi

JBL

Jensen

JVC

Kenwood

Luxman

Marantz

McIntosh

NAD

Nakamichi

NEC

Nikko

Onkyo

Optimus

Panasonic

Philips

Pioneer

Quasar

Radio Shack

RCA

Sansui

Sanyo

Sharp

Sherwood

Sony

Technics

Toshiba

Yamaha

Zenith

017 036 039 010 051 041 006 026 027 052 042 044 049 062 008 038 046 059 038 061 007 030 005 028 048 056 064 019 058 040 054 040 063 003 021 055 041 047 009 012 016 029 050 014 004 023 041 045 050 047 071 072 057 042 044 060 047 000 024 043 002 020 050 025 048 053 065

Audio Cassette

NO. Brand Code

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Aiwa Curtis Mathes Denon Fisher GE Kenwood NAD Nakamichi Onkyo Optimus Panasonic Philips Pioneer Proscan Quasar Radio Shack RCA Sansui Sanyo Sherwood Sony Technics Yamaha

039 041 052 042 049 070 048 056 040 054 055 041 047 015 050 013 018 041 045 070 050 047 070 057 044 047 043 050 053

Audio System

NO. Brand Code

Aiwa

Carver

Curtis Mathes

Denon

Harman Kardon

Jerrold

Kenwood

Nakamichi

Panasonic

Philips

Pioneer

RCA & Dimensia

Sansui

Sanyo

Scientific Atlanta

Sony

Starcom

Technics

Yamaha

039 051 041 052 046 066 068 048 056 054 015 016 013 014 018 041 031 032 033 034 035 057 044 067 043 066 050 053

Amplifier

NO. Brand Code

1 2 3 4

Kenwood Pioneer RCA Yamaha

048 041 069 001 053

Phono

NO. Brand Code

1 2 3 4

Kenwood Pioneer Sony Yamaha

048 041 043 053

HTIB

NO. Brand Code

BOSE

Philips Toshiba

010 022 025

36 TFT-LCD TV

Operation

Maintenance

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

1. Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little

fabric softener or dish washing detergent. Wring the cloth until it`s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for a long time (such as a vacation), it`s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

Owner s Manual 37

1366X768(Dot)

120V~ , 60Hz

NTSC ATSC Clear QAM

Specifications

External Antenna Impedance

HL26ATB

HL32ATB

Dimensen(WX X ) Unit::inches/mmDH (Including stand)

26.7X9.7X20.7inches 679X246X525 mm

31.9X9.7X24.4 inches 811X246X621mm

75 ohm

27.6/12.5

35.3/16.0

The specifications shown above may be changed without prior notice for quality improvement.

38 TV LCD-TFT

Troubleshooting

For the sake of time and cost, it is strongly recommended that you check out the problem by yourself according to the instructions listed hereunder before contacting the after-sales service for technical assistance.

Verify if the television is properly plugged.

No picture, no sound

Blank screen

No sound

Verify if the television is properly supplied power. Verify if electricity is available.

Verify if correct signals are input. Press INPUT button to change signal input to TV input. Restart the television of power supply is interrupted.

Press Mute button and verify if Mute mode is set. Switch to other channel and verify if the same problem happens. Press VOL+ button to see if the problem can be solved.

Poor sound

No picture in some channel

No color for some channel program (black and white)

Spots with some or all pictures

Horizontal/vertical bars or picture shaking

Television out of control

Note: Do not leave the television with static picture in an extended period as it may result in residual image on your

television screen.

Verify if sound system is correct. Refer to some chapter for adjust.

Verify if correct channel is selected. Adjust the antenna. Make adjustments by Fine Tune and Manual Scan.

Verify if the same problem exists in other channels. Check out of picture and sound systems. Refer to relative instructions in the Manual for color adjust.

Verify if the antenna is correctly connected. Verify if the antenna is in good condition. Make fine adjustment of channel.

Check for local interference such as an electrical appliance or power tool.

Disconnect the television from power supply and, 10 seconds later, connect the television to the power supply. If the problem still exists, contact authorized after-sales service for technical assistance.

Note: Production of the plasma screen requires high and precision technologies. However, there might be some dark or bright (red, blue or green) spots, or

some anomalistic stripes or spots. This is not defect. If the TV set is used in an area 2,400 meters above the sea level where the air pressure is below 750hpa, the picture on the plasma screen may be affected and a muffled sound might be produced. These phenomena might happen in the area 1,500 meters above the sea level. This is resulted from difference between air pressures inside and outside the display. This is not a defect covered by the limited warranty.

Owner s Manual 39

Warranty

This Haier brand product, when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product with a new or re-manufactured equivalent at no change to the purchaser, for parts or labor for the periods set forth below:

This warranty does not apply to the appearance of the product or the exterior of the product, which has been damaged or defaced, altered or modified in design or construction. It does not apply to the additional excluded items set forth below:

The warranty commences on the date the item was purchased and the original purchase receipt must be presented to the authorized service center before warranty repairs are rendered.

Responsibility of Haier to the purchaser with respect to the product, and shall

constitute full satisfaction of all claims, whether based on contract, negligence, strict duality or otherwise. In no event shall Haier be liable, or in any way responsible for any damages or defects in the product which were caused by repairs or attempted repairs performed by anyone other than an authorized service center or dealer; nor shall Haier be liable, or in any way responsible for incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so that above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(s) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Haier.

The warranties described herein shall be the sole and exclusive warranties granted by Haier and shall be the sole and exclusive remedy available to the purchaser. Correction of defects in the manner and for the period of time described herein, shall constitute complete fulfillment of all abilities and

Warranty period for this product:

and labor

Additional items excluded from warranty coverage: non-rechargeable batteries. Where to obtain service: For the location of the nearest Haier authorized service center or to obtain product literature, accessories, supplies or customer assistance, please call 1-877-337-3639. What to do to obtain service: ship or carry in your product to an authorized service dealer or center .Be sure to have proof of purchase. If you ship the product, be sure it is packaged carefully. Haier America New York, NY 10018

one year parts

40 TV LCD-TFT

Haier HL32ATB, HL26ATB User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual