R
HL19R1/HL19K1/HLC19R1/HLC19K1/HL22R1/HL22K1/HLC22R1
HLC22K1/HL22F1
LCD TV & LCD TV/DVD Combo
USER MANUAL
Please read this manual carefully
before using this TV set and keep it
for future reference.
WARNING AND CAUTION
CAUTION
RISK ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of
uninsulated dangerous voltage within the product s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
!!
accompanying the appliance.
!!
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
POLARIZED PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock, do not perform any
servicing other than that contained in the operating instructions unless
you are qualified to do so.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. (This item is only for TV with DVD models.)
IMPORTANT SAFETY INSTRUCTIONS
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
10) Only use attachments/accessories specified by the manufacturer.
11) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
12) Unplug this apparatus during lightning storms or when unused for long
periods of time.
13) Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
14)The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the apparatus.
15)The mains plug or appliance inlet is used as the disconnect device, remain it
readily operable during the apparatus normal use.
Safety Instructions(for TV with DVD)
PRECAUTIONS
FCC WARNING-This equipment may
generate or use radio frequency
energy.Changes or modifications to this
equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction
manual.The user could lose the authority
to operate this equipment if an
unauthorized change or modification is
made.
LASER SAFETY
This unit employs a laser.Only a qualified
service person should remove the cover
or attempt to service this device,due to
possible eye injury.
CAUTION:USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION:VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN AND
INTERLOCK DEFEATED.DO NOT
STARE INTO BEAM.
LOCATION:INSIDE,NEAR THE DECK
MECHANISM.
CONTENT
Safety Notice Items...................................................................................
Front Panel Controls..................................................................................
Connection Options...................................................................................
Remote Control ........................................................................................
Remote Control Key Functions....................................................................
Connection Instructions.............................................................................
External equipment Connections..............................................................
Antenna Connection.............................................................................
VGA Setup.............................................................................................
Component Setup................................................................................
VCR Setup...........................................................................................
HDMI Input.........................................................................................
Cable TV Setup....................................................................................
External Component Source Setup.......................................................
Basic Operating Instructions.......................................................................
Switch On/Off the TV set..........................................................................
Choose the input source..........................................................................
Audio Control..........................................................................................
Mute......................................................................................................
INFO.....................................................................................................
Select the TV Channel You Want.............................................................
Picture Mode...........................................................................................
Audio Mode............................................................................................
Sleep.....................................................................................................
GUIDE...................................................................................................
ARC button.............................................................................................
.Button...................................................................................................
CH.LIST button.......................................................................................
FAVORATE button......................................................................................
Menu Operations.......................................................................................
Video Menu Options...............................................................................
Video Menu Options Continued...............................................................
Audio Menu Options................................................................................
Audio Menu Options Continued................................................................
Channel Menu Options.............................................................................
Channel Menu Options Continued..............................................................
Function Menu Options.............................................................................
Function Menu Options Continued..............................................................
Lock Menu Options ..................................................................................
Lock Menu Options Continued..................................................................
PC Menu Options....................................................................................
PC Menu Options Continued....................................................................
Stream media broadcast system
............................................................
DVD Features..........................................................................................
Special Function Playback.......................................................................
DVD System Setup...................................................................................
Playable Discs.........................................................................................
Disc Protection and DVD Characteristics...................................................
Troubleshooting Guide...............................................................................
Specifications...........................................................................................
Warranty ..................................................................................................
Note: DVD is available only on certain models. Please refer to your original set
for specific details.
1
2
3
4
5
7
7
7
8
8
9
9
10
10
11
11
11
11
11
11
12
12
12
12
12
12
13
13
13
14
14
15
16
17
18
19
20
21
23
24
28
29
30
32
34
35
39
40
41
42
43
Safety Notice Items
Incorrect usage may cause fire or electric shock.
required when you are installing, using and cleaning this machine. To
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
l Please read and understand all the instructions before operation;
l
Please keep this manual for later use;
l
Please comply strictly with the warning instructions on the machine and
in this book;
l Please comply with the instructions provided;
l Please do not use additional devices that are not recommended by
manufacturer:
l
Before operation, please make sure that the operating voltage of your unit is
correct;
l Do not place the unit on unstable, dusty and humid places;
l Never put the unit in direct sunlight or near heat sources;
l Allow enough space for proper ventilation;
l Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
l
Do not remove the back cover. If service is needed, please contact an
Authorized service technician.
To prevent this, please do as
ensure
Front Panel Controls
INPUT MENU VOL- VOL+ CH- CH+ POWER
R1 series series F series K1 1
Control Panel Function
1. POWER Press to turn on and off the TV.
2. INPUT Selects the input signals.
3. MENU Menu display. Press to access the on-screen menu display.
4. VOL- Volume down / Left button to adjust the item in the OSD.
VOL+ Volume up / Right button to adjust the item in the OSD
/Press to enter.
5. CH- TV channel down / to select the item in the menu.
CH+ TV channel up / to select the item in the menu.
6. Power indicator
7. Remote Sensor Receivers IR signals from the remote control.
Do not put anything near the sensor ,which may
block the remote control signal.
Connection Options
DVD
R1 series seriesK1
STOP
PLAY/PAUSE
PREV
OPEN/CLOSE
NEXT
OPEN/CLOSE
PLAY/PAUSE
STOP
PREV
NEXT
DVD insert
Label towards back
ATN IN R-AUDIO-L R-AUDIO IN-L
Pr Pb Y
S-VIDEO IN
COMPONENT IN
VIDEO
The above figure is for reference
only, connections may differ
depending upon the models and
terminals of some models may be
on the back bottom of the set
VGA INUSB HDMI
PC AUDIO IN
1.ANT IN(Antenna Input) Connect cable or antenna signals to the TV, either
directly or through your cable box.
2.Headphone jack : Headphone audio output terminal.
3.Audio in Connect audio output from an external device to these jacks.
4.S-VIDEO Connect S-Video out from an S-Video device to the jacks.
5.Audio in Connect audio output from an external device to these jacks.
6.Video in Connect video output from an external device to this jack.
7.USB input Connect a USB flash drive to view JPEG images or listen to MP3
songs.
8.VGA Connect to the VGA 15PIN analog output connector of a PC
graphics card to use set as a PC display.
9.PC audio in Connect the audio output from the pc to the PC audio input port.
10. HDMI: Connect a HDMI device to receive digital audio and uncompressed
digital video.
11. Component Input Connect a component video device to these jacks.
Remote Control
Installing Batteries
Remove the battery cover.
Insert two size AAA batteries matching
the +/-polarities of the battery to the +/marks inside the battery compartment.
Precautions
Make sure that there is no
obstacle between the remote
controller and television set.
Keep the remote control
away from heat sources or
humid areas to ensure
effective performance of
the remote.
As strong light may interfere with the
signals, change your position to
operate the remote control if
the television cannot be turned
on or off as expected.
Make sure that two AA 1.5V or AAA
depending up the model alkaline
batteries are loaded. The batteries
must be of the same type, must be
inserted properly, and must not be
rechargeable.
Remote Control Key Functions
When using the remote control, aim it
towards the remote sensor on the TV
1
USB
2
GUIDE
3
4
PICTURE AUDIO ARC FAVORITE
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
INPUT
MUTE
VOL CH
MENU
SLEEP DISPLAY
OPEN/CLOSE
PLAY/PAUSE
REV
D.MENU
D.CALL
SEARCH
ANGLE
(For TV with DVD)
CCD MTS/SAP CH.LIST
ENTER
DVD
RECALL
EXIT
STOP REPEAT
PREV NEXT
D.AUDIO
SETUP
SUBTITLE
PROGRAM
1.Press to turn on and off the TV
2.Press to switch input source to USB in
3.Display the guide when you are watching analog or
digital channels
21
4.Select a closed caption
22
5.Press repeatedly to cycle through the available picture
23
modes
24
25
6.Press to cycle through different sound settings
7.Show the input source
8.Switches the video sound on or off
9.Press to adjust the volume
26
10.Press to open the on-screen menu
11.Thumbstick(Up/Down/Left/Right)
Allows you to navigate the on-screen menus
and adjust the system settings to your preference.
27
12.Press to display the sleep timer option
28
13.DVD PLAY/PAUSE
14.DVD Open/close
15.DVD FAST FORWARD
29
16.DVD FAST REVERSE
17.DVD CALL
30
18.DVD MENU
19.DVD SEARCH
20.DVD ANGLE
31
21.Press to switch input source to DVD in
22.Open the channel list in TV
23.Select MONO, STEREO, SAP in NTSC system
24.Open the favourite channel list in TV
32
25.Press to change the aspect ratio
33
26.Press to change a channel
34
27.Press to select digital channels. For example, to enter
35
“54-3”, press “54”, “ ” and “3”
36
37
28.Press to jump back and forth between two channels
38
29.Press to scan through channels. To scan quickly
39
between the last two channels, press and hold down
40
either +/- .
30.Exit On Screen Display
31.Accesses the highlighted item in the on-screen menu
32.Press to display the TV status information on the top
of the TV screen
33.DVD STOP
34.DVD REPEAT
35.DVD Previous Chapter
36.DVD Next Chapter
37.DVD AUDIO Mode
38.DVD SETUP
39.DVD PROGRAM
40.DVD SUBTITLE
LEFT
UP
RIGHT
DOWN
Remote Control Key Functions
When using the remote control, aim it
towards the remote sensor on the TV
PICTURE
1
ARC
2
3
4
MENU
5
6
EXIT
7
USB
8
9
REV
10
DISPLAY GUIDE
11
12
13
(For TV without DVD)
CCD
MTS/SAP
1 2 3
4 5 6
7 8 9
INPUT
0
CH+
VOL-
ENTER
CH-
PLAY/PAUSE
STOP
PREV
FAVORITE
VOL+
AUDIO
SLEEP
MUTE
RECALL
REPEAT
NEXT
CH.LIST
14
15
16
17
1.Press repeatedly to cycle through the available
picture modes
2.Press to change the aspect ratio
3.Select a closed caption
4.Show the input source
5.Press to open the on-screen menu
6.Volume/Channel Selection
18
7.Exit On Screen Display
8.Press to switch input source to USB in
9.DVD PLAY/PAUSE
19
10.DVD fast reverse
11.DVD fast forward
20
12.Press to display the TV status information on the top
of the TV screen
21
13.Shows program schedule in TV
14.Press to turn on and off the TV
15.Press to cycle through different sound settings
22
23
24
25
26
27
28
16.Press to display the sleep timer option
17.Select MONO, STEREO, SAP in NTSC system
18.Press to change a channel
19.Press to select digital channels. For example, to
enter “54-3”, press “54”, “ ” and “3”.
20.Switches the video sound on or off
21.Accesses the highlighted item in the on-screen menu
22.Press to jump back and forth between two channels
23.DVD REPEAT
24.DVD STOP
25.DVD Next Chapter
26.DVD Previous Chapter
27.Open the channel list in TV
28.Open the favorite channel list in TV
Note: the instruction on this manual takes
remote of TV with DVD for example.
Connection Instructions
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
RF coaxial wire (75 ohm)
Bronze Wire
VHF antenna
UHF antenna
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
NOTE: Cables shown are not included with the TV
Turn clockwise to tighten.
Be careful not to bend the bronze
wire when connecting the antenna.
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
If the antenna needs to be split for two
Tvs, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
Bronze Wire
Connection Instructions
VGA Setup
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the user guide supplied with
your computer and ensure that it has
a VGA connector;
2.Make sure that the power of the LCD
-TV and the PC are off;
3.Connect a D type 15-pin PC interface
cable ( not supplied ) to the PC video
interface connector on the PC. Then
connect the other end to the PC video
interface connector on the back of the
LCD-TV.Tighten the screws on the PC
connectors once they are firmly
connected;
4.Turn on the power of the LCD-TV first ,
and then turn on the power of the PC;
5.Press INPUT button to set the video input mode of the LCD-TV to PC;
Once the input for PC is selected and if you see no image press function
F8 on you pc.
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be changed, change the PC graphic
card or consult the manufacturer of the PC graphic card.
Resolution
Mode
VGA
SVGA
XGA
Note: All above listed are subject to VESA criteria.
Component Setup
Resolution
640x480
800x600
1024x768
Line frequency(KHz)
31.5
37.9
48.4
How to connect
Connect the DVD video outputs (Y, PB, PR)
to the Component(Y, Pb, Pr) IN jacks on
the TV and connect the DVD audio outputs
to the AUDIO IN jacks on the TV, as shown
in the figure.
NOTE: If your DVD player does not have
component video output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use INPUT button on the remote
control to select the proper input.
VGA IN
PC AUDIO IN
Frame frequency(Hz)
60
60
60
Pr Pb Y
COMPONENT IN
R-AUDIO-L
S-VIDEO IN
Connection Instructions
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
Composite or S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are off;
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from
the VCR's output jacks to the TV input jacks,
as shown in the figure.
When connecting the TV to VCR, match
the jack colors (Video = yellow, Audio
Left = white,and Audio Right = red).
If you connect an S-VIDEO output from
VCR to the S-VIDEO input, the picture
1
quality is improved; compared to conne cting a regular VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner s
manual.)
.
3
.Turn on the LCD-TV first ; and then turn on the
power of the AV device;
4.Press t button to set
INPUT
the video input mode of the
LCD-TV to S-Video mode or
Video mode.
Pr Pb Y
COMPONENT IN
2
VCR
ATN IN R-AUDIO-L R-AUDIO IN-L
S-VIDEO IN
VIDEO
HDMI Input
How to connect
Connect the cables from the external equipment's
output jacks to the TV input jacks, as shown in the figure.
How to use
1. Select the input source by using button
on the remote control or on the TV.
2. Operate the corresponding external equipment.
Refer to external equipment operating guide.
INPUT
HDMI
HDMI
Connection Instructions
Cable TV Setup
- After subscribing to a cable TV service from a local provider you can watch cable
TV programming. The TV cannot display TV programming unless a TV tuner
device or cable TV converter box is connected to the TV.
- For further information regarding cable TV service, contact your local cable TV
service provider(s).
Connection Option 1
1. Select 3 or 4 with channel switch on cable
box.
2. Tune the TV channel to the same selected
output channel on cable box.
3. Select channels at the cable box or with
the cable box remote control.
Connection Option 2
1. Connect the audio and video cables from
the Cable Box's output jacks to the TV
input jacks, as shown in the figure.When
connecting the TV to a Cable Box, match
the jack colors
(Video = yellow, Audio Left = white, and
Audio Right = red).
2. Select the input source by using the
INPUT button on the remote control.
3. Select your desired channel with the
remote control for cable box.
ATN IN R-AUDIO-L R-AUDIO IN-L
Pr Pb Y
COMPONENT IN
S-VIDEO IN
VIDEO
External Component Source Setup
How to connect
Connect the audio and video cables from
the external equipment's output jacks to the
TV input jacks, as shown in the figure.
When connecting the TV to external equipment, match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red).
How to use
1. Select the input source by using the INPUT
button on the remote control.
2. Operate the corresponding external equi pment. Refer to external equipment ope rating guide.
R-AUDIO IN-L VIDEO
Basic Operating Instructions
Switch On/Off the TV set
When the POWER button is pressed and the LCD-TV is turned on, the
indicator light on the front of the LCD-TV changes from red to green. When the
LCD-TV is turned off using the power button, the LCD-TV will go into standby
mode and the indicator light turns red(or turns dark).
NOTE: The color of the indicator light may differ based upon the model purchased.
Choose the input source
Change the picture source so you can watch your TV, VCR, DVD, Cable ,
or any other devices that are connected to your TV.
1. Press INPUT button to enter the Select Source menu and then use
INPUT button to select the desired items TV, Video, S-Video, Component
DVD, PC, HDMI .
2. Press button to confirm . ENTER
Audio Control
1.Press VOL+ button to increase the volume. A number will appear
on screen indicating the volume level.
2.Press VOL- button to decrease the volume. A number will appear
On screen indicating the volume level.
Mute
1.Press MUTE button to mute the sound temporarily. A mute icon
Appears on the screen.
2.Press MUTE button or VOL+ again to restore the sound.
The mute icon disappears.
INFO
Press INFO button to display current program information.
Basic Operating Instructions
Select the TV Channel You Want
You can use the number buttons and button on the remote control to directly
select TV channels and press to confirm.
And you can press the buttons(CH+/CH-) on the remote control or on the panel to
make a selection.
Picture Mode
Press PICTURE button on the remote control for menu display . For desired mode
as follows:
Mild Standard Vivid Custom
Audio Mode
Press AUDIO button on the remote control for menu display . For desired mode
as follows:
Off Concert Living Room Hall Bathroom Cave Arena Church
Sleep
ENTER
Press SLEEP button to set the time : Off
-60 Min-90 Min-120 Min-180 Min-240Min
This function allows you to turn off the television after a pre-selected
number of
minutes
-5 Min-10 Min-15 Min-30 Min- 45 Min
GUIDE(only available in digital signal)
Press GUIDE button in digital channels to display Guide menu.(This menu is
just for you to see the information and can not be changed)
Press CH+/CH- to select information for you to look over.
ARC button
Press to select the aspect ratio among Normal, Wide, Zoom and Cinema.
(Display mode may differ from different inputs)
Basic Operating Instructions
button
Press to select additional channels (digital and analog) being broadcast by the
same station. For example, to select digital channel “11.1”, press “11”, then
press “ ” and “1”.
CH.LIST button
Press to display the channel list. Press VOL+/VOL- to turn to the next or previous
page, press CH+/CH- to select the item and Enter button to select the channel you
desired.
FAVORATE button
Adding favorite channels
Press FAVORATE under one channel. The favorite channel list opens.
Press CH+ or CH– to select a blank box, then press Enter to confirm .
The channel will be added to the favorites channel list.
Press Enter again, the channel will be removed from the favorites channel list.
Tuning to a favorite channel
Press FAVORATE. The favorite channel list opens.
Press CH+ or CH– to select the channel and press Enter to confirm .
Your LCD TV automatically tunes to the channel you selected.
Menu Operations
* In this manual, the OSD (On Screen Display) may be differ from your TV
These are examples to illustrate the TV's operation.
Press Input to select the input source. The menu for each source may be
different .
1. Press MENU button to display the main menu, and to select the main
menu function.
2. Press /ENTER button to enter the sub menu and to go up and down to
select the desired option .
3. Press /ENTER button to confirm and to make changes to the
/
parameters.
4. Press EXIT button to return to the main menu.
5. Press MENU button to exit the menu screen.
Video Menu Options
Picture quality can be adjusted for any input separately .
The picture quality on the screen can be adjusted as follows:
/
/
1. Press MENU button and until the following menu appears on the
/
screen.
2. Press /ENTER button to enter the menu function and to scroll up
/
and down to select the desired function.
3.Press /ENTER button to confirm and increase and decrease
/
the level to adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Video
Audio
Channel
Function
Lock
Video
Note:
1.The options may be different because of the inputs.
2.Symbols on top of the menu in this manual may differ from the actual set display.
3.The picture options can be changed only in Custom mode only, the other modes
are fixed.
Mode Custom
Brightness
Contrast
Color
Tint
Sharpness
Color Temperature
Advanced Video
CH+/-
ENTER
VOL+/-
Select
EXIT
50
50
50
0
50
BackAdjust
Menu Operations
Video Menu Options continued
Function:
Mode: Select the type of picture which best corresponds to your viewing
requirements by selecting Picture Mode in Video menu. You may select the
picture mode directly by pressing the PICTURE button on the remote control.
Brightness :Press button and /ENTER to confirm, then press to
/
/
adjust the brightness of the picture.
Contrast : Press button and /ENTER to confirm, then press to
/
/
adjust the contrast of the picture.
Color : Press button and /ENTER to confirm, then press to adjust
/
/
color saturation.
Tint : Adjust the tone of the picture .
Sharpness : Adjust the amount of the detail enhancement , the image
sharpness rises as the number increases (By increasing the level, it will show
cleaner and clearer images and by decreasing the level, it will make the picture
smoother).
Color Temperature: This will increase or decrease Warm (red) and Cool (blue)
colors to suit personal preferences.Select Cool to give the white colors a blue tint,
Standard to give the white colors a neutral tint, Warm to give the white colors
a red tint. Custom to allow you change the color manually.
Contrast, Brightness, Sharpness , Color Temperature and Tint can only be adjusted when
Mode in Custom mode.
Advanced Video:To adjust the picture in advanced level:
DNR: Digital Noise Reduction. To adjust to reduce the appearance of digitizing
error caused by the compression:Medium,Strong,Auto,Off and weak.
Black Level Extender: To adjust the ability in the black areas detail of the
picture:On and Off.
White Peak Limiter: To adjust the ability in the white areas detail of the
picture:On and Off.
CTI: Color Transient Intensity.To adjust the picture for color errors:Medium,Strong,
Off and weak.
Flesh Tone:To adjust the flash colors:On and Off.
Adaptive Luma Control: To adjust changes in the luminance of the picture:On and Off
Menu Operations
Audio Menu Options
Sound can be adjusted for any input as follows:
1. Press MENU button and until the following menu appears on the
/
screen.
Audio
Video
Audio
Channel
Function
Lock
Balance
Bass
Treble
Sound Surround On
Mode Off
Equalizer Off
AVL Off
Audio Only
ENTER
CH+/VOL+/-
Select
EXIT
0
50
50
BackAdjust
You can adjust sound options to the levels you prefer.
2. Press /ENTER button to enter the Audio menu and to go up and
/
down to select the desired option .
3.Press /ENTER button to confirm and increase and decrease
/
the level to adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired audio quality has been achieved .
Function :
Balance : Press button and /ENTER to confirm, then press to adjust
/
/
the audio output between left and right speakers.
Bass : Press button and /ENTER to confirm, then press to increase
/
/
or decrease the level of the lower-pitched sounds .
Treble : Press button and /ENTER to confirm, then press to increase
/
/
or decrease the level of the higher-pitched sounds
Surround: To turn the simulated surround sound on and off.
Mode : Press /ENTER to select the type of sound which best corresponds to
your lightning requirements by selecting Mode in Audio menu.
Equalizer: To adjust the equalizer: Off, Rock, Pop, Live, Dance, Techno, Classic
and Soft.
Menu Operations
Audio Menu Options Continued
AVL This will reduces the differences in volume level among broadcasters.
Audio Only: Press /ENTER button to confirm, the following display will appear
on the screen:
If enter Audio Only mode, press POWER to exit!
OK Cancel
Press to select OK , then press OK to confirm. The TV screen will
be black and no picture , but the sound is still normal.
You can press POWER button to reveal the picture on the screen.
SAP Broadcasts Setup:
This TV can receive MTS stereo programs and SAP
(Secondary Audio Program) that accompanies the stereo program;
if the station transmits an additional sound signal as well as the original one.
When having selected SAP button on the remote control, this TV can only
receive the signal when the TV station transmits the proper signals.
Mono sound is automatically received if the broadcast is only in Mono; even
though Stereo or SAP has been selected.
Select Mono if you want to listen to mono sound during stereo/SAP
broadcasting.
Stereo or SAP can be received in a Analog channel.
1. Use the SAP button to select your desired MTS mode in a analog signal.
Each time you press the SAP button, Mono, Stereoor SAP appear.
If other languages are available on the digital signal, select them with the
SAP button.
2. Press EXIT button to save and return to TV viewing.
Menu Operations
Channel Menu Options
Channel
/
Video
Audio
Channel
Function
Lock
Tuner Antenna
Channel Scan
Channel Skip
Channel Label
CH+/-
Select
VOL+/-
EXIT
Back
1. Press MENU button and until the following menu appears on the screen.
Note: Channel menu will appear in main menu only in TV mode.
2. Press /ENTER button to enter the Channel menu and to go up and
/
down to select the desired option .
3.Press /ENTER button to confirm and increase and decrease the level to
/
adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved .
Function:
Tuner: Press / button to select Antenna or Cable .
Channel Scan: Press / button to start to scan, press EXIT to cancel
ENTER
ENTER
Video
Audio
Channel
Status: Scanning...
Analog Channels: 4
Digital Channels: 3
Antenna
Function
Lock
Channel Scan
EXIT
40%
Cancel
All channels now available will be
automatically preset in order .After the search has finished, the first program
number will display on the screen. This search automatically adds only the
active channels in your area to the TV's memory. It deletes any channels on
which there is no broadcast or a poor signal. The channels found are
automatically saved.
Menu Operations
Channel Menu Options Continued
Channel Skip: Press / button to enter the submenu then press
/
to select the channel number (eg.2) and press to confirm, a mark
ENTER
ENTER
will be display in the pane as follows and this channel will be skipped next time
you press but you can press digits button to select the channel. If you want
to resume the channel, press button again.
/
Video
Audio
Channel
Function
Lock
Channel Skip
ENTER
2 Analog
3 Analog
4 Analog
5 Analog
5-1 Digital
6 Analog
7 Analog
8 Analog
9 Analog
10 Analog
ENTER
CH+/-
Select
EXIT
Set
VOL+/-
Back
Channel Label: Allows you to name the channel that is selected.
Press / button to enter the submenu.
ENTER
Video
Audio
Channel
Function
Lock
Channel Index
Channel Label
1
CH+/-
Select
EXIT
Channel Label Set
Then press to select Channel Index and Channel Label and to
/ /
VOL+/-
Back
select the position of the item that you want to change, afterward press INPUT
to input the numbers and symbols and button to confirm.
ENTER
Menu Operations
Function Menu Options
1. Press MENU button and until the following menu appears on the
/
screen.
Video
Audio
Channel
Function
Lock
Function
2. Press / button to enter the Function menu and to go up and
Language English
OSD Timeout Short
OSD Transparency Middle
Screen Mode Full screen
Blue Screen On
DPMS On
Time Setup
Closed Caption
Default
CH+/-
Select
EXIT
VOL+/-
Back
/ ENTER
down to select the desired option .
3.Press / button to confirm and increase and decrease
ENTER
/
the level to adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved .
Function:
Language: Press button to select language of the OSD.
OSD Timeout: Press to select Middle, Short and Long to change the
/
/
time of the OSD display.
OSD Transparency: Press to select among Low, High and Middle
/
to change the transparency of the OSD. To select Low, the OSD is opacity.
Screen Mode: Press to select among Full Screen, Normal, Wide,
/
Zoom and Cinema to change the display mode. ( display mode may differ from
different inputs)
Blue Screen: Press to select On , the screen will be in blue after
/
3 seconds if there is no signal.
DPMS: PC Power Management. To set On, the set will be in standby mode
automatically if no signal in 2 minutes; if signal input , the set will be on again
automatically.
Time Setup: Press / to enter the submenu.
Time Zone: Press to select the appropriate time zone.
ENTER
/
Menu Operations
Function Menu Options Continued
Video
Audio
Time Zone Central
Date/Time
Sleep Timer Off
Channel
Function
Lock
CH+/-
Select
EXIT
Time Setup
VOL+/-
Back
Date/Time ENTER: Press / to enter the submenu.
Video
Audio
Channel
Function
Lock
Date/Time
Auto: Press to select On or Off . When Auto mode on , the time can not be
/
Auto Off
Date
Time 00:00:00
Timer On
On Time 00:00:00
Off Time 00:00:00
CH+/-
Select
VOL+/-
EXIT
Back
adjusted. Select Off , you can operate to set the time manually.
Date: Press to select the position and digits button to set the date.
Time: Press to select the position and digits button to set the time.
/
/
Timer: Press to select On or Off. To select Off, the time can not be adjusted.
On Time/Off Time: Press to select the position and digits button to
/
/
set the time.
Closed Caption: Press / to enter the submenu.
ENTER
Video
Audio
Channel
Function
Lock
Closed Caption
NTSC Caption Off
DTV Caption Off
DTV Caption Style
CH+/-
Select
VOL+/-
EXIT
Back
Menu Operations
Function Menu Options Continued
NTSC Caption: Press to select the Closed Caption options. It helps the
/
hearing impaired with the broadcast program, as well as helping children
learn how to read. A built in decoder displays the audio portion of a program as text
on the screen when this option is selected.
CC1: When CC1is displayed on TV means CC mode is turned on.
CC2 to CC4: For other modes of video related broadcast information.
Text1: For program guide and other information displayed by broadcasters.
(This blocks a large portion of the picture on your screen).
Text2 to Text4 :For other modes of information displayed by broadcasters.
(This blocks a large portion of the picture on your screen).
IMPORTANT: Closed captioning availability entirely depends on broadcasters
supplying the signal. Therefore, closed captioning might not always be
available and language availability will differ by broadcast.
Note: Select CC1 for full translation of the primary language such as English in
your area. Select CC2 for secondary language translation such as French or
any other language that may be broadcast in your area.
DTV Caption: Press to select Service1/Service2/Service3/Service4/
/
Service5/Service6/Off.
DTV Caption Style: Press /ENTER to enter the submenu.
Video
Audio
Channel
Function
Lock
DTV Caption Style
Style
Size
Text Color
Text Opacity
BG Color
BG Opacity
Window Color
Window Opacity
CH+/VOL+/-
Custom
Large
White
Solid
Black
Solid
Black
Solid
Select
EXIT
Back
ABC
Style: Press to select one of Default and Custom. When you select
/
default, the others are disable and can not be adjusted. When you adjust the
following system,A mark of ABC in a pane will be on the right of the OSD to
display the effect.
Size: Press to select
/
the size of caption display according to your own
preference.
Text Color: Press to select the text color or the opacity of the text box of
/
caption display according to your own preference.
Select a color and one of the opacity options.
Text Opacity: Press to specify the opacity for the text color.
BG Color: Press to select a background color.
/
/
Menu Operations
Function Menu Options Continued
BG Opacity: Press to select the opacity for the background color.
Window Color: Press to select according your own preference
Window Opacity: Press to select the edge color according your own
/
/
/
preference.
Default: Press /ENTER to enter the submenu.
Are you sure?
OK Cancel
/
Press to select OK or Cancel then OK to confirm. If OK, the parameter
will return to the factory set.
Lock Menu Options
1. Press MENU button and until the following menu appears on the
screen.
/
Video
Audio
Channel
Function
Lock
Enter Password
EXIT
Lock
Back
2. Press /ENTER to enter and then press digits button to input the digits( The
initial password is 0000. If you forget your password, you can always input 9443
to regain control) . The menu will display as follows:
Video
Audio
Channel
Function
Lock
Lock
Channel Block
Program Block
Password
Clean All
ENTER
Enter
CH+/VOL+/-
Select
EXIT
Back
Menu Operations
Lock Menu Options Continued
Channel Block: Press /ENTER to enter the submenu as follows.
Video
Audio
Channel
Function
Lock
Channel Lock
/
Press to select the channel you want to lock, then press ENTER to confirm.
10-1 Digital
11 Analog
11-1 Digital
12 Analog
13 Analog
14 Analog
14-1 Digital
14-2 Digital
14-3 Digital
15 Analog
ENTER
WCAU-DT
MBC DTV
ATSC-1
ATSC-2
ATSC-3
CH+/-
Set
VOL+/-
Select
EXIT
Back
The channel is locked and a lock mark appears in the pane. If you want to unlock
the channel, repeat the operation above again. Then press EXIT to exit step by
step.
Program Block: Press /ENTER to enter the submenu as follows.
Video
Audio
Channel
Function
Lock
Program Block
Parental Lock
Parental Guide
MPAA Rating
CA Eng Rating
CA Fren Rating
Block Unrated
CH+/VOL+/-
On
On
Select
EXIT
Back
Parental Lock: Press to select On or Off. Used to lock all the system
/
following . To set Off, the system following can not be available.
Parental Guide: Press /ENTER to enter the submenu as follows.
Press / to select the item you want to lock.
/ /
Then press ENTER to confirm to lock and press again to resume it.
Parental Guide Technology:
The "P.L. Technology" allows you to use U.S. and Canadian Movies and TV
PROGRAMS Guide ratings to block certain types of TV programs and movies.
To clearly understand TV program rating codes, read the following information:
Menu Operations
Lock Menu Options Continued
Video
Audio
Channel
Function
Lock
Parental Guide
U.S. TV Program Ratings
TV-Y: For all children - these types of rated programs are designed for a very young
audience, including children from ages 2-6.
TV-Y7: Directed towards older children - this type of rated programs may include
comedic violence of mild physical, or may frighten children under the age of 7.
TV-G: General audience - these types of rated programs contains little or no
violence, no strong language, and little or no sexual dialogue and situations.
A D L S V FV
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Allowed Rating Blocked Rating
CH+/-
Select
EXIT
ENTER
Set
VOL+/-
Back
TV-PG:Parental Guidance Suggested-this type of rated programs may contain
limited violence, some suggestive sexual dialogue and situations, and rare
language.
TV-14: Parents strongly cautioned-these types of rated programs may contain sexual
content, strong language and more intense violence.
TV-MA:Mature audience only these types of rated programs may contain sexual
violence, explicit sexual content and profane language.
(A)All: Blocks all available sub_ratings.
(D)Dialogue: This type of rated programs contain dialogue with sexual content.
(L)Languag: This type of rated programs contain offensive language.
(S)Sex: This type of rated programs contain sex.
(V)Violence: This type of rated programs contain violence.
(FV)Fantasy Violence : This type of rated programs contain Fantasy and cartoon
violence.
Menu Operations
Lock Menu Options Continued
MPAA Rating: Press /ENTERto enter the submenu as follows.
Press to select the item you want to lock. Then press ENTER to confirm
/
to lock and press again to resume it.
Video
Audio
Channel
Function
Lock
MPAA Rating
G
PG
PG-13
R
NC-17
X
Allowed Rating Blocked Rating
CH+/-
Select
EXIT
ENTER
Set
VOL+/-
Back
To understand clearly about movie rating codes, read the following list:
U.S. Movie Rating Chart
G: General Audience-this type of movie rating means all ages admitted to see
the movie.
PG: Parental guidance suggested. Some material may not be suitable for children.
PG-13:Parents Strongly Cautioned - this type of movie rating means some material
may not be appropriate for children under13.
R:Restricted- This type of movie rating means children under 17 of age require
to be with parent or guardian.
NC-17:This type of movie rating means no one 17 and under admitted.
X: This type of movie rating means adults only.
CA Eng Rating: Press /ENTER to enter the submenu as follows.
/
Press to select the item you want to lock. Then press ENTER to confirm to
lock and press again to resume it.
Menu Operations
Lock Menu Options Continued
Video
Audio
Channel
C
C8+
G
PG
14+
18+
Function
Lock
CA Eng Rating
Allowed Rating Blocked Rating
CH+/-
Select
VOL+/-
EXIT
Back
ENTER
Set
To clearly understand Canadian program rating codes, read the following list:
Canadian English Rating Chart
C: This type of programming is intended for children under age 8. There is no
offensive language, nudity or sexual content.
C8+:These types of rated programs are generally considered acceptable for children
8 years and over. There is no profanity, nudity or sexual content.
G: These types of rated programs are generally suitable for all audiences.
PG: Parental Guidance Suggested -in these types of rated programs, some material
may not be suitable for children.
14+: In these types of rated programs, some content may not be suitable for viewers
under the age of 14.Parents are strongly cautioned not to have their children
view 14+ rated programs by pre-teens and early teens.
18+: Adults Only-these types of rated programs are only for adult viewers only.
CA Fren Rating: Press /ENTERto enter the submenu as follows.
/
Press to select the item you want to lock. Then press ENTER to confirm to
lock and press again to resume it.
Video
Audio
Channel
Function
Lock
CA Fren Rating
G
8 ans+
13 ans+
16 ans+
18 ans+
Allowed Rating Blocked Rating
CH+/-
Select
EXIT
ENTER
Set
VOL+/-
Back
Menu Operations
Lock Menu Options Continued
Canadian French Rating Chart
G:These types of rated programs are generally suitable for all audiences.
8 ans+: Children 8 years and above (French)
13 ans+: 13 years old and above(French)
16 ans+: 16 years old and above(French)
18 ans+: Adults Only-these types of rated programs are only for adult viewers only.
Blocked Unrated: Press to select On or Off.
Used to lock all the channel not rated .
Password: Press /ENTER to enter the submenu , press digits button to input
the number of 0-9 twice in the New Password and Confirm Password. Then you
can change the password when you input the same number twice.
Clean All: Press /ENTER to enter the submenu:
/
Press to select OK or Cancel then OK to confirm. If OK, the parameter will
return to the factory set.
Note: if there is any lock mark on the top of the set such as channel lock, parental
lock and so on, you can press OK to resume it .( Press OK to display password
menu and input your password.)
/
Are you sure?
OK Cancel
PC Menu Options
1. Press MENU button and button to select Video menu in PC mode.
2. Press /ENTER button to enter the Video menu and to go up
and down to select the desired option .
/
/
Menu Operations
PC Menu Options Continued
ENTER
3.Press / button to confirm and increase and decrease
the level to adjust the selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved .
/
Video
Audio
Function
Lock
Video
PC: Press button to select and / to confirm, the PC menu as below:
Video
Audio
Function
Lock
PC
Auto Sync: Press button and then press to auto adjust that automatically
/
Mode Custom
Brightness
Contrast
Color Temperature
Advanced Video
PC
CH+/VOL+/-
ENTER /
Auto Sync
H Position
V Position
Phase
Clock
CH+/-
ENTER
VOL+/-
Select
Select
EXITENTER
EXIT
50
50
BackAdjust
50
50
50
50
BackAdjust
adjusts the available options for the best viewing configuration.
H Position: Press button and then press to adjust the horizontal
/
/
position of the picture.
V Postion: Press button and then press to adjust the vertical position
/
/
of the picture.
Phase: Press and then press to adjust the phase of the picture.
Clock: Press button and then press to adjust the clock of the picture.
/
/
/
/
USB Input
1.1.Supporting media and file format:
Digital pictures (.JPG) and digital
music (.MP3) files
Due to differences in the file code and
file mode, It is possible that some
files cannot be read.
2.Before starting operation, verify
USB storage device is of FAT32 and
FAT file system format. At present,
this television does not support NTFS
and the file systems of other format.
3.External card reader supports most
digital cards available in the market.
Readable digital cards are classified
according to the property of card
readers and can be connected to
mobile hard disks (working voltage
5.0V, working current not over 500mA).
4.The television operation may be
halted due to excessive rate of
information code errors. In such case,
restart the system. Please note there are many nonstandard USB
mobile devices in the market. If a
nonstandard device is used then an
identification problem may occur.
To play picture
1.Press USB button on the remote to
enter stream media system.
The system start up takes about 3
second. Then insert the USB drive
in the USB input.
2.Press button to select Picture
. Press ENTER to enter.
3.Press / button to select
/
folder
/ /
desired picture, and then press
ENTER button to enter the play
interface.
1.Play mode: None/Dissolve/Wipe right/Wipe left/
Wipe up/Wipe down/Box in/Box out
2.Play time: Short/Medium/Long;
3.File name 4.Pause/Play
5. Duration/Rotate 6.Effect
7.Infomation
1
4
3
2
7
5
6
4.Press the button on the remote control
to select the adjusted item, press
ENTER button to confirm.
3
2
REV
4
1
PLAY/PAUSE
5
STOP
PREV
REPEAT
6
1.Play or pause;
2.Stop;
3.Repeat;
4.No available;
NEXT
5.No available;
6.Play previous picture;
7.Play next picture.
7
5.Press EXIT button to return to the
previous menu.
Press USB button to exit the USB
mode.
Note you may play the pictures among selected.
USB Input
To play music
folder
REV
4
/
/ /
2
1
PLAY/PAUSE
STOP
PREV
5
6
3
REPEAT
NEXT
7
1.Play or pause;
2.Stop;
3.Repeat
4.Fast reverse;
5.Fast forward;
6.Play previous music;
7.Play next music.
1.Press button to select Music
. Press ENTER to enter.
2.Press / button to select
desired music, and then press ENTER
button to enter the play interface.
3.Press the button on the remote control
to select the adjusted item, press
ENTER button to confirm.
4.Press EXIT button to return to the
previous menu.
Press USB button to exit the USB
mode.
Note You may play the music among selected.
1.Press button to select Music
. Press ENTER to enter.
2.Press / button to select
/
folder
/ /
desired music, and then press ENTER
button to enter the play interface.
3.Press USB button to turn to the main
menu. And then press button to
/
select Picture option.
Press ENTER to enter.
4.Press / button to select
/ /
desired picture, and then press
ENTER button to enter the play
interface.
To play music and picture
To play music and picture, relative
media file format will include JPEG and
MP3 files. After Picture is selected,
MP3 files set for play will open both
music and picture files for sync play
performance. As some files must be
read while music is being played, the
speed of picture operation response
might be affected.
5.Press USB button to exit USB mode.
Note Do not remove USB device from the TV until
you have exited the USB mode otherwise
you may damage the USB device.
DVD Features
Basic Playback
Preparations
Preparations
Press DVD button on the remote control
to enter the DVD status.
Note: Do not insert a disc until the DVD input states
open
Basic playback
Basic playback
1.Place the DVD in the disc slot. The disc will be
loaded automatically after one to two seconds
then the DVD player reads the DVD and displays
the opening menu If there is no disc placed in
DVD mode, OPEN will display on the screen all
the times)
Do not place a disc that is unplayable in this
DVD player.
Some discs do not start automatically. Press
PLAY/PAUSE to start playback.
2. Some discs may start playback with a menu. Use
the cursor buttons on the remote control to select
menu options and press to start. You
may also press the digit buttons to select a menu
option directly. Many DVDs will not allow this during
start-up.
Pause playback
Pause playback
PLAY/PAUSE
1. Press to pause playback (still mode).
The sound will be muted during still mode.
PLAY/PAUSE
2. Press to resume normal playback.
PLAY/PAUSE
Stop playback
Stop playback
1. Press STOP button to go to stop mode, the TV
screen will show the start logo. With some discs,
such as DVD or CDs, the player can resume
playback from the point where it was stopped.
2. Press PLAY/PAUSE to resume playback from the
location where the playback was stopped.
3. Press STOP twice to stop completely.
Previous and Next
Previous and Next
During Playing, pressing the PREV button will
restart the last chapter and skip chapters
backwards with each subsequent press until the
start of the disc is reached.
Each press of NEXT button during playing will
skip the current chapter and play the next one.
Fast forward and Fast reverse
Fast forward and Fast reverse
1. Press FWD to fast forward through the disc.
Each time the FWD button is pressed, the
fast forward motion speed changes.
PLAY/PAUSE
2. Press to resume normal playback.
3. Press REV to fast reverse through the disc.
Each time the REV button is pressed, the
fast reverse motion speed changes.
4. Press to resume normal playback.
PLAY/PAUSE
Single step playback
Single step playback
1. When paused, press continuous
to single step forward to the next frame in the
video.
2. Press to resume normal playback.
PLAY/PAUSE
PLAY/PAUSE
DVD Features(Continued)
Advanced Playback
IMPORTANT NOTE:
ALL DESCRIBED FUNCTIONS A FOR DVD DISCS. IF YOU PLAY OTHER DISC
FORMATS THE OPERATION AND ON SCREEN DISPLAY WILL BE DIFFERENT.
PROGRAM
SUBTITLE
Press " SUBTITLE ", the screen will display "SUBTITLE 01/XX XXXXX", "01" indicates the ordinal
number of this language; "XX" indicates total number
of language; "XXXXXX" indicates the language of
country. (The number of language depends on disc.)
This function can select up to 32 languages displayed on screen.
REPEAT
REPEAT
Press " REPEAT " and Chapter repeat will be
displayed on screen, the second press will display
Title repeat, the third press will display All repeat,
the fourth press will cancel this function.
ANGLE
ANGLE
When enjoying sports, concert or theatre, press this
key to watch same actions in different angles. (Valid
for discs possessing this function. Using a disc
recorded in multi-angle you can view the scene from
different angles,for example,front, side, whole view
and exterior scene).
D.MENU
D.MENU
Press this key to display the root menu, select
items according to your preference. (This
function will work on a DVD with a multi-layer
menu.)
PROGRAM
When playing discs, press "PROGRAM" to enter
program mode. Press the digit buttons to select the
program number that you want. When finished move
the cursor to select "START" . Press PLAY/PAUSE
to confirm. This will start the program playback.
SEARCH
SEARCH
Press "SEARCH" once to display the search
menu. Press the button again to select. Press
the program number buttons to input the item
you require. Press PLAY/PAUSE to confirm.
AUDIO
D.AUDIO
Press this key can change the mode of audio.
such as: Audio 1/2: AC 3 2 CH English
Audio 2/2: AC 3 5.1 CH English
Press this button to cycle between Mono Left, Mono
Right, Mix-Mono and Stereo.
Note: When press this button continuously, you must
allow a 3 second interval between selections.
D.CALL
D.CALL
Pressing this key will cycle through "Title Elapsed",
"Title Remain", "Chapter Elapsed", "Chapter Remain"
and "Display off ".
Special Function Playback
JPEG DISC PLAYBACK
When a disc containing standard JPEG picture files is inserted into the player, a
navigation menu will be displayed automatically. Use the UP and DOWN cursor
buttons to select a file then press PLAY/PAUSE. The slide show will commence.
Press PREV or NEXT to move between pictures. Press pause to stop on the
current picture. Press PLAY/PAUSE to resume normal playing.
A JPEG disc contains JPEG (.jpg) format picture information that can be decoded
by a micro-computer software and displayed through the video output interface or on
the television screen.
This function has many applications. For example one can save files from a scanner
or digital camera in the JPEG format, record these on a CD-R disc and present them
to an audience through this player.
The JPEG format is a convienient method to store images in a small amount of
memory space, and is ideal for archiving information.
SCREEN SAVER FUNCTION
This unit employs a screen saver mode to help protect the tube during static video pictures. This can
be turned off on the GENERAL SETUP PAGE.
DVD System Setup
DVD System Setup
General Setup Process
SETUP
PLAY/ENTER
SETUP
PLAY/ENTER
1.Press the setup button, the
general set up page will be
displayed press twice the
preference page will be displayed
2.Press / to select, the
item, then press to enter the
submenu.
3.Press / to select then
press to confirm.PAUSE
4.Press SETUP repeatedly to
exit the set-up menus.
NOTE: Preference page will be
displayed when there is no DVD in
the unit. To access this page, press
SETUP button twice.
General Setup Page
ASPECT RATIO DESCRIPTION
When using the DVD with the internal TV,
select 4 3/LB.
The following information applies only
when the DVD output is connected to an
external TV.
4:3/PS (PS = Pan and Scan)
You may select if you have a normal aspect
ratio (4:3) TV, although the NORMAL/LB
(letter box) is a more common choice. In PS
mode, widescreen material will fill the screen, but at the expense of chopping
off extreme left and right edges of the original film picture. For this feature to
work, the disc must be specially coded. Such discs are uncommon.
4:3/LB (LB = Letter Box)
You may select this if you have a normal aspect ratio (4:3) TV. Widescreen
material will be shown in pure unaltered form, allowing the entire picture area
of the original film to be viewed without any side cropping. Black bars will
appear above and below the picture.
16:9
You may select this if you have a widescreen (16:9) TV. Back bars may still
appear above and below the picture even if using a widescreen TV. This is
because some film directors prefer to use ultra widescreen aspect ratios e.g.
2.35:1. This will normally be indicated on the DVD packaging.
..General Setup Page..
Tv Display LB
Angle Mark On
Osd Lang ENG
Caption On
Screen Saver Off
..Preference Page..
Parental
Password
Default
..General Setup Page..
Tv Display LB
Angle Mark On
Osd Lang ENG
Caption On
Screen Saver Off
4 3/Ps
4 3/Lb
16 9
1 Kid Saf
2 G
3 Pg
4 Pg 13
5 Pgr
6 R
7 Nc17
8 Adult
4 3/Ps
4 3/Lb
16 9
DVD System Setup(Continued)
DVD System Setup
General Setup Page
ANGLE MARK: Users can select a particular
camera angle when playing a DVD which offers
multiple angles.
This item allows you to set Angle Mark ON or OFF.
On Screen Display (OSD) Language: Users
can select on-screen display language.
CAPTION: This function allows you to display or
hide the caption.
.
..General Setup Page..
Tv Display LB
Angle Mark On
Osd Lang ENG
Caption On
Screen Saver Off
..General Setup Page..
Tv Display LB
Angle Mark On
Osd Lang ENG
Caption On
Screen Saver Off
..General Setup Page..
Tv Display LB
Angle Mark On
Osd Lang ENG
Caption On
Screen Saver Off
On
Off
English
Spanish
On
Off
SCREEN SAVER: If the screen saver is on, then
there will be an animated picture of DVD on the
screen whenever the DVD player is idle for more
than 3 minutes .
..General Setup Page..
Tv Display LB
Angle Mark On
Osd Lang ENG
Caption On
Screen Saver Off
On
Off
DVD System Setup(Continued)
DVD System Setup
Preference Page
The Preference Page is only available when there is no disc
in the player.
SETUP
PLAY/ENTER
SETUP
PLAY/ENTER
PARENTAL: The parental
control function works in
conjunction with the
different censorship classes
assigned to DVDs. These
classes help to control the
types of DVDs that the family
..Preference Page..
Parental
Password
Default
1 Kid Saf
2 G
3 Pg
4 Pg 13
5 Pgr
6 R
7 Nc17
8 Adult
watches, There are up to 8
censorship classes for DVDs.
Note:
1 To change this setting you must enter your password.
(Initial password is 1234)
2 When set to OFF, all discs may be viewed.
PASSWORD CHANGE:
You can change your password
by entering 4 digits. You must
confirm the 4 digits before the
..Preference Page..
Parental
Password Change
Default
new password can be accepted.
NOTE:
If you forget your password
or a password is accidentally
set enter 1369 as the password.
This will enable you to regain
control.
Old Password
New Password
Confirm Pwd
DVD System Setup(Continued)
DVD System Setup
SETUP
PLAY/ENTER
DEFAULT: Resets all settings
(except password and parental
lock status) for this DVD player
back to the manufacturers
original settings. Press ENTER
..Preference Page..
Parental
Password
Default
Reset
to perform the reset.
Note:
Some functions may not be available depending on the
type of disc.
Playable Discs
The following discs can be played:
You cannot play discs other than those listed above.
You cannot play non-standardized discs, even if they may be labelled as above.
The performance of CD-R or CD-RW disc depends on the way the disc was burned. In
a few cases, their performance may not be consistant or may not even operate at all.
This DVD Player is designed and manufactured according to the Region
Management Information that is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to the Region number of this DVD
Player, this DVD player will not play that disc.
This Region number of this DVD Player is .
11
Disc Protection and DVD Characteristics
Compare DVD disc with other discs:
Encode
method
Capacity
Playing Time
Disc diameter
Horizontal
resolution
Picture
proportion
Subtitle
Language
Sound quality
Singleside
singlelayer
4.7G
133
minutes
DVD LD
Digital/MPEG
Double
Single-
-side
side
single
double-
-layer
layer
8.5G
9.4G
242
266
minutes
minutes
12cm 12cm
More than 500 line
Multiple kinds
32 kinds
8 kinds
48KHz, 96KHz/
6, 20, 24bit
Doubleside
doublelayer
17G
484
minutes
Analog
Single-side
60 minutes
double-side
120 minutes
30cm/20cm
No more than
430 line
One kind
16 kinds
at most
4 kinds
at most
44.1KHz/
16bit
SVCD
Digital
650MB 650MB 650MB
45 minutes
12cm 12cm
No more than
350 line
One kind
4 kinds
4 kinds
at most
44.1KHz/
16bit
VCD CD
Digital/
I
MPEG
74 minutes 74 minutes
No more than
250 line
One kind
2 kinds 2 kinds
44.1KHz/
16bit
Digital
44.1KHz/
16bit
Troubleshooting Guide
To assist in location possible faults use help guide below.
Troubleshooting
No picture, no sound
Blank screen
No sound
Poor sound
No picture in some
channel
No color for some channel
program (black and white)
Spots with some or
all pictures
Abnormal functioning
Verify if the television is properly plugged in.
Verify if the television is properly supplied with power.
Verify that electricity is available.
Verify if correct signals are input.
Press INPUT button to change signal input to TV input.
Restart the television of power supply is interrupted.
Press MUTE button and verify if Mute mode is on.
Switch to another channel and verify if the same problem
happens.
Press VOL+ button to see if the problem can be solved.
Verify if sound system is functional. Refer to chapter on
adjusting.
Verify if correct channel is selected.
Adjust the antenna.
Verify if the same problem exists in other channels.
Check picture and sound systems.
Refer to relative instructions in the Manual for color
adjust.
Verify if the antenna is correctly connected.
Verify if the antenna is in good condition.
Make fine adjustment of channel.
Disconnect the television from power supply and, 10
seconds later, reconnect to the power supply.
If the problem still exists, contact an authorized
service depot for technical assistance.
Note:
1.If the fault can not be repaired using the above guide consult with your local authorized
service center.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to
remove the back cover as the TV set has dangerous voltages levels inside that may be
fatal or cause fire.
Specifications
Model
Picture, sound
system
Audio output
External input port
Power requirements
Power consumption
Temperature
Humidity
Accessories
19 without DVD 19 with DVD
NTSC, ATSC, Clear QAM
1.5W+1.5W
AV input PC input S-VIDEO input PC audio input
YPbPr input Antenna input HDMI input
~120V 60Hz
60W
Working:+5 ~+35
Storage:-15 ~+45
Working:20% ~ 80%
Storage: 5% ~ 90%
Remote control
Batteries
User manual
Warranty card
80W
NOTE
Design and specifications are subject to change without notice.
Dimensions quoted in this manual are approximate.
Warranty
Warranty
Warranty
and one year parts .
90 days labor
R
V0.1
0090507193
Loading...