Page 1
Domestic Dishwasher
HDW101SS
OFFON
Fast
Half
Load
Eco
HDW101SS
GB
Code: 0120503010
Page 2
Safety Is Very Important
Close-up View (Interior)
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of this appliance.
This appliance complies with the following EEC
directives:
-73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- The appliance is not intended for use by young children or
inform persons without supervision.
- Young children should be supervised to ensure that they do
not play with the appliance.
- Keep detergents out of the reach of children.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; It is also very
dangerous to leave it exposed to the rain and elements.
- Do not lean or sit on the door when it is open as this could
overturn the dishwasher.
- Do not touch the heating element during or after a wash cycle.
- If the appliance malfunctions turn off water supply to the appli ance and disconnect the plug from the wall socket. Refer to
the section entitled, "Troubleshooting." If you cannot solve
the problem, contact a authorised service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made inoper able by cutting the power supply cord and removing the door lock.
- If the supply cord is damaged, it must be replaced by a special
cord or assembly available from the manufacturer or its ser vice agent.
- This appliance is intended for built-in and must be installed ac
cording to the installation instruction and in particular, it is re quired to have the plug accessible after installation.
- Rules to follow when using this appliance:
* Never touch the dishwasher when barefoot or with wet hands;
* We discourage the use of extension cords and multiple sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly, maintenance must
be performed, disconnect the appliance from the power supply.
Warning: Dishwasher detergents can be extremely dangerous
if swallowed. Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open. Check
that the detergent receptacle is empty after completion of the
wash cycle.
To maintain the EFFICIENCY and SAFETY of this appliance,we
recommend:
- call only service centres authorised by the manufacturer.
- always use original Spare Parts
A
B
C
D
Upper Rack
Rack Height Adjustor
Top Sprayer Arm
Lower Rack
Bottom Sprayer Arm
E
Washing Filter
F
Detergent and Rinse Aid Dispenser
G
Third Sprayer
H
Close-up View (Control Panel)
A B C D
Half
Fast
Eco
Load
I H G
ON-OFF Light
A
ON-OFF Button
B
Water heating Indicator Light
C
Low Rinse Aid Indicator Light
D
Knob For Selecting Cycle
E
Technical Characteristics
Width
HDW101SS
OFFON
F
.1.
F
G
H
I
E
Handle For Opening Door
"Eco" Button
"Half Load" Button
"Fast" Button
GB GB
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorber power
12 standard place settings
240V~ 50Hz
.2.
60 cm
60 cm
85 cm
0.03-0.6MPa
2200W
Page 3
Detergent and Rinse Aid
Loading the Dishwasher
Detergent
Detergent specifically intended for use with dishwashers must
be used. The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table." The detergent dispenser is located on the inside panel
the door.
Loading the detergent
To open the "A" cover on the dispenser, press the "B" button.
The detergent for the wash cycle should be poured into the "C"
compartment.
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.
C
A
B
Rinse Aid
This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the
door and should be filled after every 80 wash cycle (or when the
rinse aid indicator light comes on for models with this feature).
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in an anti-clockwise
direction and then pour in the rinse aid, making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dosage adjuster, located beneath the "C" cap,
with a screwdriver. There are 6 different settings; the normal
dosage setting is 3.
Important
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs, the
dosage adjuster should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjuster to a
lower setting.
C
Before placing the dishes in the dishwasher, remove any large
food particles to prevent the filter from becoming clogged. A clogged
filter will result in reducing performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they be allowed to soak before they
are washed. This will eliminate the need for extra wash cycles.
Pull out the rack when loading the dishwasher.
How to Use the Lower Rack
We recommend that you place the most difficult to clean items on
the lower rack: pots, lids, serving dishes and bowls, as shown in
the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The silverware basket can be doubled (see fig. A) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans, and it can also
be placed in the upper rack.
- Silverware should be placed in the silverware basket with the
handles at the bottom. If the rack has side baskets, the spoons
should be loaded individually into the appropriate slots. Long uten sils should be placed in the horizontal position at the front of the
upper rack.
Lower Rack
Load for 12 Standard Settings
Upper Rack
NOTE: To facilitate closing the cover, remove any excess detergent on the edges of the dispenser.
.3.
F
C
GB
How to Use the Upper Rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, as well as plates,
small bowls and shallow pans. It is recommended that dishes
placed in the upper rack are not too dirty .
Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height by using the knobs
located on the sides of the rack itself (see fig. B).
GB
.4.
fig.A
1
2
3
4
fig.B
Page 4
Turning on the Appliance
STOP
Energy Saving Tips
Starting a wash cycle
- Make sure that the plug for the appliance is inserted into the wall
socket.
- Make sure that the water supply is turned on to full pressure.
- Load the dishwasher (see the section entitled, "Loading the
Dishwasher" on page 4).
- Pour in the detergent (see the section entitled, "Detergent
and Rinse Aid" on page 3).
- Turn the knob located on the right of the control panel in
clockwise direction until the number or symbol for the cycle set ting is aligned with the reference mark (see the section entitled,
"Wash Cycle Table" on page 7).
- Press the ON-OFF button, and the ON-OFF light will turn on. At
this point, the wash cycle will begin.
If you forget to load some of the dishes
The wash cycle can be interrupted by pressing the ON-OFF button.
You can then load additional dishes and turn the appliance back
on. The cycle will start where it left off.
At the end of the wash cycle
When the knob stops turning and is aligned with a STOP mark
(see figure), the cycle has finished. Turn off the appliance using
the ON-OFF button, turn off the water supply and open the door
of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid
handling the dishes and utensils while they are still hot and more
susceptible to breakage. They will also dry better.
Cancelling or modifying a wash cycle setting
A cycle that is underway can only be modified if it has been
running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained
the wash water. If this is the case, the detergent dispenser must
be refilled (see the paragraph entitled, "Loading the Detergent"
on page 3).
Press the ON-OFF button, and the ON light will turn off. Rotate
the knob in clockwise direction to the desired cycle setting (see
the section entitled: Starting a wash cycle . Then, turn the
dishwasher back on using the ON-OFF button.
- It is important to try and run the dishwasher when it is fully
loaded to save on energy. In order to prevent odors from form ing and food from caking onto the dishes, you can run the hold
cycle.
- Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.
How to Keep Your Dishwasher in Shape
- Use the right amount of detergent: if you use too much detergent,
the result will not be cleaner dishes, but, rather, a greater nega tive impact on the environment.
Wash Cycle Adjustment Buttons
Eco Button
This button (see "close-up View - Control Panel" on page 1, letter
"G" ) is used for normal dirty dishes, pots and pans. It is a standard daily cycle. This button reduces the washing temperature
from 60
Half load Button
This button (see "close-up View - Control Panel" on page 1, letter "H" ) makes it possible to wash dishes using only the upper
rack if there are not enough dishes for a full load. This will allow
you to save on water and electricity.
to 50 saving energy costs.
It can be used before setting any of the wash cycles, except for
the intensive cycles (if included in the wash cycle table ). Please
keep in mind that the amount of detergent should also be cut in
half.
Fast
This button (see "close-up View - Control Panel" on page 1, letter
"I" ) , when pressed with wash cycle 4 (glassware) make it possible to run the wash cycle at a lower temperature (50 ) and
eliminates the drying phase.
After Every Wash
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odors are not
trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove the
plug from the socket.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products. Use only a cloth and
warm soapy water.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and a little white vinegar, or a cleaning product made specifically for dishwasher.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical position.
If absolutely necessary, it can be positioned on its back.
Seals
One of the factors that cause odors to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
sponge will prevent this from occurring.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket, turn off the water supply and leave the door of the
appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance.
.5.
GB
.6.
GB
Page 5
Wash Cycle Table
Cleaning and Special Maintenance
Cycle
Intensive
Wash
Intensive
Wash
Normal Wash
Normal Wash
(IEC-EN50242)
Eco
Button
Fast
Button
Cycle Selection
Information
Very dirty dishes, pots and
pans (not to be used with
delicate items).
Very dirty dishes, pots and
pans. (not to be used with
delicate items)
Normally dirty dishes, pots
and pans. Standard daily
cycle.
Normally dirty dishes, pots
and pans. Standard daily
cycle.
Description of
Cycle
Pre-wash with hot water.
Rinse with cold water.
Extended wash at 60
Rinse with hot water
Drying.
Pre-wash with hot water.
Rinse with cold water
Extended wash at 50
Rinse with hot water
Drying.
Rinse with cold water.
Extended wash at 60
Rinse with hot water
Drying.
Rinse with cold water.
Extended wash at 50
Rinse with hot water
Drying.
Detergent
30g
30g
25g
25g
Rinse
Aid
Filter Assembly
For best performance and results, the filter assembly must be
cleaned.
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle. For this reason, it
is a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the "A" semi-circular filter
and cup under running water. To remove the filter assembly, pull
on the cup handle in an upward direction. The entire filter assembly (made up of the "A" semicircular filter and the "B" fine filter)
should be cleaned at least once a month. To clean the filter and
the fine filter, use a cleaning brush. Then, reassemble the filter
parts as shown in the figures below and inset the entire assembly in the dishwasher, positioning in its seat and pressing
downward.
The dishwasher must never be used without the filters. Improper
replacement of the filters may reduce performance of the appliance and damage dishes and utensils.
Troubleshooting
Cleaning the Spray Arms
It may happen that food particles become encrusted on the
sprayer arms and block the hole (see "Close up view [interior]"
on page 1, letters C-F ). Check the sprayer arms periodically and
clean them when needed.
A
B
Rinse
Rinse
Glassware
Glassware
Soak
For dishes that need to be
rinsed and dried only.
For dishes that need to be
rinsed and dried only.
Economic, fast cycle to be
used for items which are sensitive to higher. Run immediately after dishes are used.
Economic, fast cycle to be
used for items which are sensitive to higher. Run immediately after dishes are used.
Pre-wash of dishes, pots and
pans while waiting for the
load to be completed after
the subsequent meal.
Rinse with hot water
Drying.
Rinse with hot water
Drying.
Wash at 50 .
Hot Rinse
Drying.
Wash at 50
Rinse with cold water.
Short cold wash to prevent
food residue from drying on
the dishes
15g
15g
It may occur that the dishwasher does not function properly or at
all. Before calling for assistance, Iet us see what can be done
first: Have you forgotten to press one of the buttons or to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the houses on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the rinse aid dosage is correct.
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service
agent and provide them with the following information:
- the nature of the problem;
- the model type number (Mod...) and the serial number (S/N...),
which are indicated on the plate located on the side of the inner
part of the door.
Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts.
.7.
GB GB
.8.
Page 6
Installation
0
Installation
Positioning the Appliance
Position the appliance in the desired location. The back should
rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to
ensure correct installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them
in or out) to adjust the dishwasher, making it level. The appliance
should not be inclined more than 2 . If the appliance is level, it
will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see fig.
1).
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear and free of impurities. If this precaution is not taken, there
is a risk that the water inlet can get blocked and damage the
appliance.
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system, heating system), as
long as it does not exceed a temperature of 60 .
In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
Anti-Flooding Protection
The dishwasher is equipped with a system that stops the supply of
water in the event of a problem with the water supply hose, or
leaks within the unit, in order to prevent damage to your home. If
for any reason the box containing the electrical components happens to get damaged, remove the plug from the socket immediately.
In order to guarantee that the anti-flooding feature operates
properly, the "A" box with water supply hose must be attached to
the water supply tap as shown in Fig.1. No other type of connection is acceptable. The water supply hose must not, under any
circumstances, be cut, as it contains electrical parts which are live.
If the length of the hose is not adequate to make a proper
connection, the hose must be replaced with one that is long enough.
This hose is available upon request from specialised retailers and
authorised service agent.
Installation
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with
the appliance (see fig.2). The free end of the hose must be at a
height between 40 and 100 cm and must not be immersed in
water.
Half
Fast
Eco
OFFON
Load
HDW101SS
MAX 100 MIN 4
fig.2
fig.1
Attention:
The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water to
spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate
(located on the stainless steel inner door of the appliance) and
that the electrical system is sized for the maximum voltage on
the rating plate, insert the plug into an electrical socket which
is earthed properly (the earthing of the appliance is a safety
requirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug, replace the plug, rather than
using adaptors or the like as they could cause overheating and
burns.
.9.
GB
GB
.10.
Loading...