Haier HDMI LE24K300, HDMI LE19K300, HDMI LE22K300 User Manual

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

LED BACKLIGHT LCD TELEVISION

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

TABLE OF CONTENTS

Important Safety Instructions 1
Product Introduction 3

General information 3
Features 4
listing 8

Installation
Panel Control Keys 16
Remote control 17
Basic Operation Instruction 19

Power On 19
Standby 19
Signal Source Selection 19
Menu Operation Instruction 20
PICTURE 20
SOUND 22
OSD 23
ADVANCE 24
TV 25

Simple troubleshooting 29

& Connection 9

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Important Safety Instructions

Thank you to choose the LED backlight LCD TV made by our company, a valuable product with excellent quality and
multiple functions. This machine will bring you more audiovisual enjoyment. Its design can insure user's safety. All
machine are strictly tested before leaving factory. But incorrect use can lead to electric shock or fire. In order to insure
safety and extend its life, please read below regulations carefully before using it and comply with the following safety
instructions.

1) Read the manual and marking label before using the machine, and keep the user manual for later use.

2) There is high voltage inside the machine, follow all the warnings and instructions strictly on the manual.

3) Don't use the attachments which are not recommended by the machine manufacturer as they may cause hazards.

4) The power cord must be placed correctly so as to avoid be trample or crush.

5) Please do not make the power socket overloaded or the power cord extended. Otherwise it will cause fire or electrical
shock.

6) If you are going to pull out the power cord from this product, please dry your hands, pull the cord by grasping the plug.
Never pull the cord itself.

7) If you will not use the machine for a long time, please pull out the power cord. Do not keep the sleeping mode for too
long time.

8) Please put this machine in the place of well ventilation instead of extremely hot, cool or moist, and direct sunshine.

9) The slots on the case is designed to release heat so as to assure that all inside components will not reach an extra
high temperature and can work normally for a long time. Please do not cover the holes while place it. Don't place the
machine near or over heat source or place in built-in installation.

10) The power cord must be taken off before you clean the machine. Don't use the liquid cleanser or aerosol cleanser. It
is recommended to use a wet soft cloth to clean the machine. Don't use the alcohol, impregnant or ammoniac liquid
to wipe the screen.

11) Please don't place it on an unstable position so as to avoid falling off.

12) Don't place the LCD TV near water source, like a bathtub, pool, washing machine, or moist cellar and similar
environment.

13) The LCD panel is fragile and expensive. The surface of the panel is easy to be scratched. Please don't use the hard

1

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

thing to knock, press, score the panel. Otherwise it will be harmful for the panel. The exchange cost is very high.

14) There is high voltage inside the machine but no parts which can be repaired by users themselves. In order to assure
the people's safety, please don't open the case to repair it by yourself. If it is needed to repair, please contact
qualified engineer to repair.

15) All cables can be connected or pull out only after power supply is turned off.

16) During a thunder rain weather, do not touch the power cord and antenna cable.

17) When the following troubles occur, please pull out the plug and call the professional engineers to repair.
A. The cable or plug is damaged.
B. The product was fallen down or the case is damaged.
C. Obvious abnormal situation occurs. In spite of correct operation according to the user manual but it still can't work
normally.
D. Some abnormal substances or liquid fall into it.
E. Unusual sound or smell sends out.

18) When the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain
readily operable.

19) The machine should not suffer from waterdrop or watersplash, do not place the vessel with water (or other liquids) on
it, for like this it is possibly to cause fire or electric shock.

20) The attaching plug should be inserted into the power point completely, otherwise it may cause spark to bring fire.

21) Please do not put candle, ash-tray, incense, inflammables or explosive nearby this machine.

22) Please do not stretch into any sharp object, metal or liquid, or touch the signal attachment or the inner of radiation
hole, in order to avoid short circuit and product damage, or possibly causing electric shock. Especially pay attention
when there are children on the spot.

23) Please don't use the machine immediately when moving the machine from low temperature place to high temperature
one, or install and use at the place of facing air conditioning, otherwise it may cause the condensation in the machine,
to cause fault.

24) Must be careful when moving this machine, avoiding being struck, especially pay attention to protect the screen part.
In addition, if using handcart, must note the injury as the product is overturned from the handcart because of hard
braking, overexerting and uneven ground.

2

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Product Introduction

General information

High-quality LED backlight LCD screen, energy saving, environmental protection, ultra-thin, brilliant features
Having inter high quality speakers, which will give you purely audiovisual enjoyment and save your table
place.
Having many ideal connectors, you may directly connect your DVD, vidicon etc. its disport components of
input connector let you enjoy beautiful image effect. The product can be used as a computer monitor with
VGA and HDMI connectors. Also it can be used as a TV machine when you insert the antenna.
Much faster response time will completely eliminate shadow of picture. seeing film and playing game may
be more fluent.
Enough colours can reach 16.7 millions kinds .
Wider viewing angle, higher brightness, higher contrast, lower consumption.
Intelligent image mode and sound mode can offer you intelligent audiovisual effect.
Built-in the latest digital comb filter, which makes image more clear. The internal 3D De-Interlace technique
can totally eliminate the screen dithering caused by interlace signals.
Own perfect timing functions, you can set time to turn off. It will be turned off in state of no signals, too.
Automatically operated convenient with telecontrol device.
Auto-setup function help you set the image to best performance in several seconds in PC mode.
Auto color balance adjustment technology takes your machine to the best color setting for all different kinds
of display adapters in PC mode.
Automatic denoise technique can greatly eliminate background noise caused by menu interference and the
noise caused by weak signals so as to make the picture on the screen clear.
Support USB interface, you can look through picture of JPG format and play music files of Mp3 format.

3

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Features

interface specification:

Interface

VGA

HDMI

CVBS Input/Output

S-VIDEO Input

YCbCr/Ypbpr

Audio Input/Output

TV(RF)

Earphone

Working Environment:

Atmosphere pressure: 86kPa 104kPa Temperature: 5 40 Humidity: 10% 85%

Storage Environment:

Atmosphere pressure: 86kPa 104kPa Temperature: -20 55 Humidity: 5% 95%

DB-15, 75 0.5~0.7Vp-p H/V:TTL Level (Support mode refer to VGA Input Mode )

Video signal: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i

Audio: LPCM

48KHz, 44.1KHz, 32KHz, 24Bit, 20Bit, 16Bit

75 1Vp-p (PAL/NTSC/SECAM)

Y: 75 1Vp-p; C: 75 0.286Vp-p

Y: 75 1Vp-p; Cb/Cr: 75 0.7Vp-p

Signal mode: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i

20K , 0.5Vp-p

75 Imbalance

16~300 100mW+100mW

Specification

4

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

The Technical Specifications for Final Product The Technical Specifications for Final Product

Model Name

Max. Resolution

Best resolution

Pixel pitch

Active area

Power supply

Volume

TV receive system

Unpacking Dimension(LHW)

Packing Dimension(LHW)

Net weight

Gross weight

Color

Surface treatments

Remote control range

Storage channels

5

LE19K300

366 768

1

360 768

1 @60Hz

0.3mm 0.3mm

409.80mm 230.40mm

100V-240VAC 60/50Hz

3W+3W

PAL+NTSC/PAL+SECAM

469 362 36

528 415 100

mm

mm

4.0Kg

5.0Kg

16.7M

Anti-glare

8m 30

199

LE22K300

1920 1080

1920 1080@60Hz

0.24825mm 0.24825mm

476.64mm 268.11mm

100V-240VAC 60/50Hz

3W+3W

PAL+NTSC

/PAL+SECAM

535 394 36 mm

595 445 100 mm

5.0Kg

6.0Kg

16.7M

Anti-glare

8m 30

199

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Model Name

Max. Resolution

Best resolution

Pixel pitch

Active area

Power supply

Volume

TV receive system

Unpacking Dimension(LHW)

Packing Dimension(LHW)

Net weight

Gross weight

Color

Surface treatments

Remote control range

Storage channels

LE24K300

1920 1080

1920 1080@60Hz

0.2655mm 0.2655mm

509.76mm 286.74mm

100V-240VAC 60/50Hz

3W+3W

PAL+NTSC/PAL+SECAM

568 418 36 mm

630 465 100 mm

4Kg

5Kg

16.7M

Anti-glare

8m 30

199

6

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

VGA input mode

LE19K300

S/N

1
2
3
4
5

Note: Recommended mode: @60Hz1360 768

LE22K300/LE24K300

S/N

1
2
3
4
5
6
7
8
9

10

Note: Recommended mode: @60Hz1920 1080

7

Mode Resolution

VGA

SVGA

XGA

WXGA

Mode Resolution

1024 768
1360 768

VGA

SVGA

1024 768

XGA

1280 720
1280 960

SXGA

WXGA

WUXGA

1280 1024

1360 768
1600 900

1920 1080

720 400
640 480
800 600

720 400
640 480
800 600

Refresh(Hz)

70
60
60
60
60

Refresh(Hz)

70
60
60
60
60
60
60
60
60
60

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Power supply: Comply with EPA standard,compatible with VESA DPMS standard.

Mode

On

Standby

Note: This specification is subject to change without notices. If there are differences between manual and real
operation, please do according to real operation.

Listing

Please make sure that all of the following items are complete
LCD TV (Include base)
User manual
Remote control
If any of above listed items is missing, please contact your dealer or our service department.

Power LED indicator

Off

On

LE19K300/LE22K300

Power consumption

35W

1W

LE24K300

40W

1W

8

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Installation & Connection

Power Connection

nsert the power plug into the socket of the electrical source (

Notes:

1. When connecting the power cord, be sure to turn off the machine and other equipment's power.

2. If a long time at leisure, please disconnect it from power supply.

AC 100V-240V, 60/50Hz).

To power socket AC 100V-240V, 60/50Hz

9

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Antenna Connection

It is better to use outdoor antenna or CATV cable if you want to watch the colorful and hi-definition pictures.

Attention:

Please turn off TV power before the outdoor antenna is connected to the TV signal input port. Outdoor antenna can't be
located near the high-voltage wires. Please pull out the plug of outdoor antenna to avoid thunder shock in thunder
weather.

10

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Computer Connection

Please connect one end of VGA cord with the output port
of the computer (available for both desktop or laptop
computer), and another end of VGA cord with the input
port of the VGA on its rear cover.

HDMI digital port Connection

Connect external HDMI high signal source to HDMI digital
input port of this machine through HDMI digital connector
cable; push "SOURCE" button to select "HDMI" signal
source.

Audio/Video machine
with HDMI interfaces

11

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

AV1 Video Signal Connection

Through composite cable, connect AV equipment VIDEO output termination to this machine VIDEO input, and AV
equipment AUDIO output termination to this machine AUDIO input, respectively; Press "SOURCE" key to select "AV1"
signal source.

S-VIDEO Input Connection

Through S-VIDEO/AUDIO cables to connect external AUDIO/VIDEO equipment to the machine's AUDIO/VIDEO input port,
and press "SOURCE" key to select "SVIDEO" si l source

gna

USB interface

Earphone Socket

CVBS, DVD Player or other
machine with CVBS/S-Video.

Earphone Socket: The TV speakers will be shut off when earphone is inserted into this socket.

AV2 Video Signal Connection
The connection method is the same as AV1; Press "SOURCE" key to select "AV2" signal source.

12

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

AV-OUT Connection

If you need watch image of DV and connect your TV game machine, you can connect audio or video output end of
DV and game machine to the monitor.

CVBS, DVD Player or other
machine with CVBS/S-Video.

AV machine

13

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

YPbPr/YCbCr Input Connection

If the signal source is DVD, Digital wired receiver or equipments with the YPbPr/YCbCr output, recommends you to
connect YPbPr or YCbCr output with the TV YPbPr/YCbCr input. In order to obtains the better picture quality, at the same
time, please connect its audio output with TV audio input as shown in the following chart. If you choose the YPbPr/YCbCr
signal, please set signal source selection under YPbPr pattern.

CVBS, DVD Player or other
machine with YPbPr/YCbCr.

G Green (Y)

B Blue (Pb/Cb)

W White(AUDIO-L )

R Red (AUDIO-R, Pr/Cr)

G B R

W

R

14

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Base installation

Base equipment act as the picture. Equip the base with the machine according to arrow point, and lock the bolt tightly.

Wall Mounting Stand

Wall Mounting Board

Wall Mounting subassembly installation

Installation for VESA Wall Mounting

1. Take off the base.

2. Fasten the wall mounting board. ( The height can be confirmed by the user).

3. Fasten the wall mounting stand at the position of VESA on the rear cover with bolts.

4. Spin M4 bolts into the left-right nuts on the wall mounting stand. 3-4 mm of depth from bolts washer to stand is
recommended.

5. Hang the machine onto the slot of the wall mounting board. Then lock the two bolts on the sides.

Note: Installation method is different because of Hanging arm hardware's structure.
Must install the wall pendant on firm wall surface, please do not install this machine on ceiling or vehicles.

15

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Panel Control Keys

4

5

6

7

1

2 3

8

3

1. Remote Receiving Sensor.

2. Power Indicator.

3. Power switch.

4. SOURCE: Press this key to enter the menu of signal source and choose signal source.

5. CH+/CH-: Press these two keys to choose channel, and adjust the options you need under OSD operation.

6. VOL+/VOL-: Press these two keys to add or reduce volume, and adjust the analog value under OSD operation.

7. MENU: Press this key to enter main menu.

8. Power on/Standby .

Note: There are some apparent differences between modes, please according to practicality.

16

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Remote control

Power

Numerical key

Smart sound

Volume

Time

Color

17

Info

POWER

F1

SMART S

OK

MENU

VOL CH

SOURCE

INFO

P/N

COLOR

MUTE

SMART P

16:9

AUDIO

Mute

Program list

Freeze picture

Smart image

OK

Cursor Key

Menu

Channel

Source

Zoom
Return

Color system

Key

POWER
MUTE
Numerical key
F1
Program list
SMART S

SMART P

Cursor key

VOL+/VOL­MENU
SOURCE
CH+/CH­INFO
Time

Return
16:9
Color
P/N
AUDIO
OK

Function

Turn on or standby
Eliminate sound
Number input button
Freeze picture
Look through or edit Program list
Intelligent sound mode selection

STANDARD NEWS MUSIC PERSONAL

Intelligent image mode selection

STANDARD DYNAMIC SOFT PERSONAL

Up or Down cursor button: function select
Left or right cursor button; analog add or reduce
Sound volume add or reduce button
Press this button to display menu
Press this button to display signal source selection menu
Select channel Number
System information display switch
Timer setting button, press this key can set time of turning down.

Off 15 30 45 60 120

Press this button to return to last watching channel
"FULL", "MOVIE", "CAPTION", "4:3", "PANORAMA"
Color temperature mode selection button:
Color system mode selection button:

Normal Warm Cool

PAL NTSC(SECAM) Auto

Optional
Confirm operation

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Remote control battery installation method:

Take off the cover of battery box, fix two AAA batteries with 1.5 volt, and conform with the polarity of remote control
battery box.

Note: Appearance of the remote control may be different from this picture, please according to practicality.

Precautions for use of remote control:

1. When using remote control you should point it to the remote-control inductive window. The goods between remote
control and inductive window may hinder normal operation.

2. Do not cause the remote control to receive fierce vibration. In addition, do not set or place the remote control under
direct sunlight, for the thermal energy will cause the distortion of remote control.

3. When remote-control inductive window of main machine is under direct sunlight or intense illumination, the remote
control may malfunction, by now, please change the angle of illumination or this machine, or approach the inductive
window to operate the remote control.

4. When the battery voltage is insufficiency it influences the remote control distance, you should replace with new battery;
when not to use the remote control for long or the battery is exhausted, please take out the battery, in order to avoid
bringing the battery leakage to corrode the remote control and thus cause it out of commission.

5. Do not use different batteries. The mix use of new and old batteries is not allowed, you should use battery pair.

6. Do not throw battery into fire, charge or disassembly, especially do not charge, assemble and disassemble, heat or
burn to the used battery. Please observe the related environmental protection stipulation on wasted battery.

18

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Basic Operation Instruction

Power On

Plug power cord into the electrical socket, press '' '' button on right side lower part of the back cover , then press '' ''
key on the back cover, or press ''Power'' key on the remote control to turn on the TV.

Standby

Press ''Power''key on the remote control. TV will be in standby.

Special Attention:

1. TV set will automatically turn to standby if there is no signal input for 5 minutes when TV turns on.

2. TV set will automatically turn to standby when the preset time of turning off reaches.

3. If you do not use it for a long time ,please turn off the power supply for the machine . Do not let the machine work in
standby state for a long time.

Signal Source Selection

Press ''SOURCE'' key either on the remote control or on the front panel. ''MENU OF SIGNAL
SOURCE'' will be displayed on the screen. Then press ''Up/Down'' key on remote control or
"CH+/CH-" key on the front panel to choose the signal source such as

YPbPr, HDMI1, HDMI2, PC, USB

the front panel and TV will switch the current signal source to the signal source you choose.

. Press ''OK'' key on the remote control or ''MENU" key on

TV, AV1, AV2, SVIDEO,

TV

AV1
AV2
SVIDEO
YPbPr
HDMI1
HDMI2
PC
USB

19

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Menu Operation Instruction

Press ''MENU'' key on the remote control or on the front panel,
then the TV will display the main menu.

1. Press ''Left/Right'' key on the remote control or ''VOL+/VOL-''
key on the front panel to select the adjustment sort menu, which
includes 5 sorts:

PICTURE, SOUND, OSD, ADVANCE, TV.

2. Press ''Down''key on the remote control or ''CH-'' on the front
panel to enter the adjustment sort menu.

3. Press ''Up/Down'' key on the remote control or ''CH+/CH-'' on
the front panel to select what is needed to adjust in sort menu.

4. Press ''Left/Right'' key on the remote control or ''VOL+/ VOL-''
on the front panel to adjust the value or setting.

5. Press ''Menu'' key to exit the main menu when the TV displays

CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
PICTURE MOD E
SCALE
COLOR TON E
3D NR

SEL ADJ

PICTURE

STANDARD
FULL
NORMAL

MIDDLE

MENU

EXIT

the Main Menu; Press ''Menu'' key to return to previous menu when the TV displays the submenu; Press ''Source''key to
display the signal source menu or exit signal source menu.

6. During the operation, the selections which can not be adjusted at current mode will be hidden automatically and the
color of the selections will be changed into gray.

7. Menu Operation Instruction in this manual is explained according to TV mode. The operations in other modes are
similar to the one in TV mode. Users can take it as reference.

PICTURE

Select to enter the PICTURE submenu. Press "Up/Down" key on the remote control or "CH+/CH-" key on the front
panel to choose what you need. Press the "Left/Right" key on the remote control or the "VOL+/VOL-" key on the front
panel to adjust analog value or state (see below table).

50
50
50
50
50

20

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Special Attention

1. The Hue function is available only for NTSC system.

2. The value adjusted by user, such as Contrast, Brightness,
Saturation, Hue, and Sharpness will be saved automatically
by the machine as personal mode.

Remote Control Shortcut Keys
SMART P: Press SMART P key on the remote control. You can
switch the function among the "STANDARD", "DYNAMIC",
"SOFT", "PERSONAL" four modes.
16:9: Press 16:9 key on the remote control, you can switch the
mode among the "FULL", "MOVIE", "CAPTION", "4:3",
"PANORAMA" five modes.

Option

CONTRAST

BRIGHTNESS

HUE

SATURATION

SHARPNESS

PICTURE MODE
SCALE

COLOR TONE

3D NR

Adjust the contrast of whole
picture

Adjust brightness and blackness
of whole picture

Adjust the hue of whole picture

Adjust the saturation of whole
picture

Adjust the sharpness of whole
picture

Select picture mode
Select picture scale
Select color temperature mode
of the picture

Select model of 3D NR

Function

21

PICTURE

EXIT

50
50
50
50
50

CONTRAST
BRIGHTNESS
HUE
SATURATION
SHARPNESS
PICTURE MODE
SCALE
COLOR TONE
3D NR

SEL ADJ

STANDARD
FULL
NORMAL
MIDDLE

MENU

Description

Increasing analog value increases Contrast;
Decreasing analog value decreases Contrast(0-100).

Increasing analog value increases brightness;
Decreasing analog value decreases brightness(0-100).

Increasing analog value increases green;
Decreasing analog value increases purple(0-100).

Increasing analog value increases color;
Decreasing analog value decreases color (0-100).

Increasing analog value increases definition;
Decreasing analog value decreases definition (0-100).

"STANDARD", "DYNAMIC", "SOFT", "PERSONAL" four modes.

"FULL", "MOVIE", "CAPTION", "4:3", "PANORAMA",
There are three Color Temperature modes,

"NORMAL , , " "WARM" "COOL ".

"MIDDLE", "STRONG", "WEAK", "OFF".

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

SOUND

Select to enter the SOUND submenu. Press "Up/Down" key on the remote control or the key "CH+/CH-" on the front
panel to choose what you need. Press the "Left / Right" key on the remote control or the "VOL+/VOL-" key on the front
panel to adjust analog value or state (see below table).

Special Attention

1. Normally, 50 value of adjustment is recommended;

2. The treble or bass analog value which is adjusted by the
users will be saved as the personal mode by the machine

Remote Control Shortcut Keys
SMART S: Press SMART S key on the remote control. You can
switch the function among the

PERSONAL

" " four modes.

, "STANDARD","NEWS", "MUSIC",

MUTE: Open or close sound.
VOL+/VOL-: Add or reduce volume.

Option

BASS

TREBLE

Adjust bass value

Adjust treble value

BALANCE Adjust balance of left or right sound

SOUND MODE

Adjust audio effect mode

Function Description

Increasing analog value increases bass;
Decreasing analog value decreases bass (0-100).
Increasing analog value increases treble;
Decreasing analog value decreases treble (0-100).
Increasing analog value decreasing left volume;
Decreasing analog value decreases right volume(0-100).

"STANDARD", "NEWS", "MUSIC", "PERSONAL" four modes.

BASS
TREBLE
BALANCE
SOUND MOD E

SEL ADJ

SOUND

STANDARD

MENU

EXIT

50
50
50

22

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

OSD

Select to enter the OSD submenu. Press "Up/Down" key on
the remote control or "CH+/CH-" key on the front panel to choose
what you need. Press the "Left/Right" key on the remote control
or the "VOL+/VOL-" key on the front panel to adjust analog value
or state (see below table).

OSD - H POSITION
OSD - V POSITION
OSD - DURATION
OSD - HALFTONE
OSD - LANGUAGE

OSD

ENGLISH

50
50
15

100

SEL ADJ

Option Function Description

OSD-H POSITION

OSD-V POSITION

OSD-DURATION

OSD-HALFTONE

OSD LANGUAGE

Adjust H-position of OSD menu

Adjust V-position of OSD menu

Adjust duration of OSD menu

Adjust halftone of OSD menu

Choose OSD menu display
language

Increasing analog value, OSD menu move toward right;
Decreasing analog value, OSD menu move toward left (0-100).

Increasing analog value, OSD menu move toward down;
Decreasing analog value, OSD menu move toward up(0-100).

Increasing analog value, extend duration time of OSD menu(5-60).

Increasing analog value increases halftone;
Decreasing analog value decreases halftone(0-100).

There are many languages to select.

23

MENU

EXIT

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

ADVANCE

Select to enter the ADVANCE submenu. Press "Up/Down" key
on the remote control or "CH+/CH-" key on the front panel to
choose what you need. Press the "Left/Right" key on the remote
control or the"VOL+/VOL-" key on the front panel to adjust analog
value or state (see below table).

SLEEP - TIMER
DCC
BLUE SCR EEN
RESETTING

ADV ANCE

OFF
OFF
ON

SEL ADJ

Option Function Description

SLEEP - TIMER

DCC

BLUE SCREEN

RESETTING

Set sleep time of the machine

Open or close DCC

Open or close BLUE SCREEN

Resume to setting of factory

Off, 15M, 30M, 45M, 60M, 120M unit: minute.

"",

"ON/OFF" two states.

"ON/OFF" two states.

Reset all values to setting of factory.

MENU

EXIT

24

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

TV

Select to enter the submenu. Press "Up/Down" key on the
remote control or "CH+/CH-" key on the front panel to choose
what you need. Press the "Left/Right" key on the remote control
or the "VOL+/VOL-" key on the front panel to adjust analog value
or state (see below table).

TV

COLOR SYS TEM
SOUND SYS TEM
MTS
SKIP
AUTO SCA N
MANUAL SEA RCH
FINE TUN ING
CHANNEL EDI T

TV

AUTO
M
MONO
OFF

Option Function Description

COLOR SYSTEM

SOUND SYSTEM

Select color system

Select sound system

MTS Select MTS modes

SKIP

AUTO SCAN

MANUAL SEARCH

FINE TUNING

CHANNEL EDIT

Select skip or not

Select auto search

Select manul search

Select fine tuning

Select channel edit

""PAL, NTSC, AUTO three modes.

"I, D/K, M, AUTO, B/G" five modes.

"STEREO, MONO, DUAL , DUAL " four modes.

"ON/OFF" two states.

Please refer to "AUTO SCAN"

Please refer to ""MANUAL SEARCH

Please refer to ""FINE TUNING

Please refer to ""CHANNEL EDIT

25

SEL ADJ

MENU

EXIT

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

AUTO SCAN

Select to enter the submenu of . Then press ''Up/Down'' key
on the remote control or ''CH+/CH-'' on the front panel to select

AUTO SCAN

'' ''. The machine perform search after pressing ''Right''

TV

53.00

MHZ

CH

2

key on the remote control or ''VOL+''on the front panel. (In the process of searching the channel automatically, press the
key of ''MENU'' on the remote control to stop searching). Meanwhile, it will show Current Channel, Frequency. All of the
TV programs will be saved automatically.

MANUAL SEARCH

Select to enter the submenu of . Then press ''Up/Down'' key
on the remote control or ''CH+/ CH-''on the front panel to select

MANUAL SEARCH

'' ''. Then press the key of ''Right'' on the remote

TV

CHANNEL

SEARCH

2

45.25

control or ''VOL+'' on the front panel to enter submenu of MANUAL SEARCH. Press ''Left/Right'' key on the remote control
or ''VOL+/VOL-'' on the front panel to select channel No.. Press ''Up/Down''key on the remote control to select ''SEARCH '',
press ''Left/Right'' key on the remote control again, the machine begin searching toward low frequency or high frequency.
(In the process of searching the channel automatically, press the key of ''MENU'' on the remote control to stop searching).

FINE TUNING

Select to enter the submenu of . Then press ''Up /Down''
key on the remote control or ''CH+/ CH-'' key on the front panel to

TV

FINE TUNING

55.25

select ''FINE TUNING''. Press ''Right'' key on the remote control to enter submenu of ''FINE TUNING''. Press ''Left/Right''
key on the remote control to adjust from low frequency or high frequency.

MHZ

MHZ

CHANNEL EDIT

Select to enter the submenu of . Then press ''Up/Down'' key on the remote control or ''CH+/CH-'' on the front panel

TV

26

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

to select '' ''. Press ''Right'' key on the remote
control to enter submenu of '' '' (Press program
list key on the remote control to enter submenu of ''

EDIT

NAME: Press ''Cursor'' key on the remote control to select
channel. Press ''1'' key on the remote control to name. Press
''UP/Down'' key on the remote Control to select l or number.
Press ''Left/Right '' key on the remote control to and
then press ''UP/Down'' key on the remote control to select l

CHANNEL EDIT

'').

CHANNEL EDIT

CHANNEL

etter

move digit

etter

001

002

003
004
005
006
007
008
009
010

1 NAME 2 DELETE 3 SWAP MENU EXIT

011
012
013
014
015
016
017
018
019
020

021
022
023
024
025
026
027
028
029
030

or number. Press ''1'' key on the remote control to confirm.

DELETE: Press ''Cursor'' key on the remote control to select channel which you wish delete. Press ''2'' key on the remote
control, and then press ''1'' to confirm.

: Press key on the remote control to select channel which you wish change name's position, press ''3'' key

SWAP ''Cursor''

on the remote control, then press ''UP/Down'' key on the remote control to select channel, press ''1'' to confirm.

Select Channels with "CH+/CH-" Key

Press Program key on the remote control or "CH+/ CH-" key on the front panel to select the channels.

Select channels with the Return key you can go to the last channel when pressing the Return key. For example, if the last
channel is 10 and the current channel is 20, you will go to channel 10 when pressing the Return key. You can switch the
two favourite channels as you like.

27

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Select Channels with Numeric Keys

1. Operations to select channels with 1 digit (0-9):
Press the number keys (0-9)on the remote control to select TV channel directly .

2. Operations to select channels with 2 digits (10-99):
Press the number keys with 2 digits (10-99) on the remote control to select TV channels.

3. Operations to select channels with 3 digits (100-199):
Press the number keys with 3 digits (100-199) on the remote control to select TV channels.

Note: With the mode of AV1, AV2, SVIDEO, YPbPr, HDMI1, HDMI2, PC, all functions and
adjustments are similar with TV. User can check it at convenience. HDMI connector can
realize DVI connector function with external HDMI/DVI commutator.

USB signal source operation

Please insert USB memory card into USB interface of TV, press "SOURCE" key on the remote control or front panel to
select USB signal source (if you don't insert the USB memory card into USB interface of TV, operation is invalid), press
"OK" key to enter.

Note: The USB interface only support mobile U disk, can't connect mobile hard disk , also can't connect to the computer

USB interface. Some mobile U disk may not be compatible, please replace the mobile U disk.

28

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Simple troubleshooting

Symptom

Snowflake speckle and
sound noise.

TV image is better, but
has noise.

No image. No sound.

TV image have stripe.

TV image have shadow.

No color.

TV no sound.

29

Factor

1.Antenna cable connector is
loose, cable is damaged.

2.Channel setting is incorrect.

3.Antenna cable type is not
matching.

4.Direction or position of antenna
cable is incorrect.

5.Signal is weak.

TV system setting is incorrect. Enter to menu, reset sound system again ."TV"

Power plug is loose, power
cord don't connect well.

Signal is exposed to disturb,
such as car, neon light, electric
blower etc.

1.TV signal is reflected by valley
or building.

2.Toward direction of antenna
cable is incorrect.

1.Color saturation is too low.

2.Color system is incorrect .

1.Volume setting is too low.

2.Sound is muted.

3.Sound system is incorrect.

1.Check the antenna cable connector plug whether
or not loose, cable whether or not perfect.

2.Refer to channel setting method, resetting again.

3.Check antenna cable type(VHF/UHF)

4.Adjust direction or position of antenna cable .

5.Attempt to use signal amplifier.

1.Check power cord whether or not connect well.

2.Check if the machine is on standby.

3.Check if the power switch button is on

Don't use electric blower around machine, adjust
antenna cable direction to reduce disturb.

1.Use high directional antenna cable. Use FINE
TUNING of .

2.Adjust toward direction of antenna cable.

"PICTURE"

1.Enter to add up color saturation.

"TV"

2.Enter to change color system.

1.Adjust volume to proper value.

2.Press MUTE button on remote control to

eliminate mute.

3.Enter to change sound system.

""

"TV"

Solution

"TV"

HAIER 19L11A / 22L11A / 23L11 ( )(6M16

Symptom

Computer no display, and
prompt no signal input, red
indicator LED twinkling.

Remote control distance is
short, lose control.

Computer display faintly.

Computer display image
excursion, not full screen,
over screen.

Noise Signals at turning off.

Can not operate this
machine.

CAUTION: Don't let your machine display the same picture for a long time, please set up a screen protection
procedure. If a high contrast picture remains for along time, this picture will bring a 'leave shadow' in screen.
Usually the 'leave shadow' will disappear gradually when you turn off the machine power. However, this trouble
can't be repaired , Which isn't in range of warranty.

Signal cable is loose or fall off.

1.Receive window of remote
continue was covered by
objects.

2.The battery energy of remote
control is to low.

1.Adjustment is incorrect.

2.Display mode is incorrect.

1.Adjustment is incorrect.

2.Display mode is incorrect.

Electrical release at turning off.

Exterior influence, for example
lightning, static electricity and so
on, which are possibly to disturb
the normal operation of this
machine.

Factor

Solution

Check signal cable whether or not loose, fall off,
reconnect well again.

1.Remove objects, avoiding cover the receive
window of remote control.

2.Change battery.

1.Use auto-adjustment function.

2.Use commend mode.

1.Use auto-adjustment function.

"GEOMETRIC"

2.Enter to adjust horizontal or

vertical position.

3.Use recommended mode.

It is normal.

Press " " button to turn off electrical source,
then press " " button to turn on the TV again
after 1-2 minutes.

30

HAIER 19L11A / 22L11A / 23L11 ( )(6M16