Haier HCI604TB1 User Manual

INDUCTION HOB

Model: HCI604TB1

INSTALLATION AND USER INSTRUCTIONS

Please read the instruction manual carefully before operating your new hob.

Safety Warnings

Your safety is important to us. Please read this information before using your cooktop.

Electrical Shock Hazard

• Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it.

• Connection to a good earth wiring system is essential and mandatory.

• Alterations to the domestic wiring system must only be made by a qualified electrician.

• Failure to follow this advice may result in electrical shock or death.

Cut Hazard

• Take care - appliance edges are sharp.

• Failure to use caution could result in injury or cuts.

Important safety instructions

• No combustible material or products should be placed on this appliance at any time.

• Please make this information available to the person responsible for installing the appliance as it could reduce your

installation costs.

• In order to avoid a hazard, this appliance must be installed according to these instructions for installation.

• This appliance is to be properly installed and earthed only by a suitably qualified person.

• Failure to install the appliance correctly could invalidate any warranty or liability claims.

Operation and maintenance Electrical Shock Hazard

• Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack,switch the appliance off immediately at the mains power supply (wall switch) and contact a qualified technician.

• Switch the cooktop off at the wall before cleaning or maintenance.

• Failure to follow this advice may result in electrical shock or death.

Health Hazard

• However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their doctor

or implant manufacturer before using this appliance to make sure that their implants will not be affected by the electromagnetic field.

• Failure to follow this advice may result in death.

Hot Surface Hazard

• During use, accessible parts of this appliance will become hot enough to cause burns.

• Do not let your body, clothing or any item other than suitable cookware contact the Induction glass until the surface is cool.

• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot

• Keep children away.

• Handles of saucepans may be hot to touch. Check saucepan handles do not overhang other cooking zones that are on. Keep

handles out of reach of children.

• Failure to follow this advice could result in burns and scalds.

Cut Hazard

• The razor-sharp blade of a cooktop scraper is exposed when the safety cover is retracted.Use with extreme care and always

store safely and out of reach of children.

• Failure to use caution could result in injury or cuts.

Important safety instructions

• Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers that may ignite.

• Never use your appliance as a work or storage surface. Never leave any objects or utensils on the appliance.

• Do not place or leave any magnetisable objects (e.g. credit cards, memory cards)or electronic devices (e.g. computers, MP3 players) near the appliance, as they may be affected by its electromagnetic field.

• The kitchen should not be immersed in water or under running water or any kind of liquids.

• Never use your appliance for warming or heating the room.

• After use, always turn off the cooking zones and the cooktop as described in this manual (i.e. by using the touch controls). Do

not rely on the pan detection feature to turn off the cooking zones when you remove the pans.

• Do not allow children to play with the appliance or sit, stand, or climb on it.

• Do not store items of interest to children in cabinets above the appliance. Children climbing on the cooktop could be seriously injured.

• Do not leave children alone or unattended in the area where the appliance is in use.

• Children or persons with a disability which limits their ability to use the appliance should have a responsible and competent person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to

themselves or their surroundings.

• Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be done by a qualified technician.

• Do not use a steam cleaner to clean your cooktop.

• Do not place or drop heavy objects on your cooktop.

• Do not stand on your cooktop.

• Do not use pans with jagged edges or drag pans across the Induction glass surface as this can scratch the glass.

• Do not use scourers or any other harsh abrasive cleaning agents to clean your cooktop, as these can scratch the Induction

glass.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order

to avoid a hazard.

•This appliance is intended to be used in household and similar applications such as: -staff kitchen areas in shops, offices and other working environments; -farm houses; -by clients in hotels, motels and other residential type environments ; -bed and

breakfast type environments.

•WARNING: The appliance and its accessible parts become hot during use.

Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.

•This appliance can be used by children aged from 8 years and above and persons with reduced physical,sensory or mental

capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

•Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

•WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.NEVER try to extinguish a fire with water, but switch off the appliance

and then cover flame e.g. with a lid or a fire blanket.

•WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock, for hob surfaces of glass-ceramic or similar material which protect live parts

•A steam cleaner is not to be used.

•The appliance is not intended to be operated by means of an external timer or separate remote-control system.

CAUTION:The cooking process has to be supervised.A short term cooking process has to be supervised continuously. WARNING:In order to prevent tipping of the appliance,this stabilizing means must be installed.Refer to the instructions for

installation.

WARNING:Use only hob guards designed by the manufactuer of the cooking appliance or indicated by the manufacture of the appliance in the instruction for use as suitable or hob guards incorporated in the appliance.The use of inappropriate guards can

cause accidents.

This appliance incorporates an earth connection for functional purposes only

Congratulations on the purchase of your new Induction Hob. We recommend that you spend some time to read this Instruction / Installation Manual in order to fully understand how to install correctly and operate it.

For installation, please read the installation section. Read all the safety instructions carefully before use and keep this Instruction / Installation Manual for future reference.

Danger of fire: Do not store items on the cooking surfaces.

CAUTION: The cooking process has to be supervised. short term cooking process has to be supervised continuously.

PRODUCT OVERVIEW

Top View

Max. 1500W

zone

Max. 2000W

zone

TECHNICAL DATA

Model Power supply

HCI604TB1

Before using your New Induction Hob

• Read this guide, taking special note of the ‘Safety Warnings’ section.

• Remove any protective film that may still be on your Induction hob.

Using the Touch Controls

• The controls respond to touch, so you don’t need to apply any pressure.

• Use the ball of your finger, not its tip.

• You will hear a beep each time a touch is registered.

• Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them. Even a thin film of water may make the controls difficult to operate.

Choosing the right Cookware

• Only use cookware with a base suitable for induction cooking. Look for the induction symbol on the packaging or on the

bottom of the pan.

• You can check whether your cookware is suitable by carrying out a magnet test. Move a magnet towards the base of the pan. If it is attracted, the pan is suitable for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

2. If “ ” does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base. Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Use pans whose diameter is as large as the graphic of the zone selected.Using a pot a slightly wider energy will be used at its maximum

efficiency.If you use smaller pot efficiency could be less than expected.Pot less than 140 mm could be undetected by the hob. Always centre your pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

Good Bad Bad Bad Bad Bad Bad

(recessed base) (convex base) (undersize) (oversize) (moisture on hotplate) (no utensil)

To start cooking

1. Power On When the mains power supply is switched on, the buzzer beeps once and all the indicators light up for 1 second, then go out. This indicates that the ceramic hob has entered standby mode. When the hob is in the standby mode all the indicator lights do not shine, all the controls are disable except the “ON/OFF” and “keylock” control.

2. Touch the ON/OFF control. After power on, the buzzer beeps once, all displays show “ – “ or “ – – “, indicating that the induction hob has

entered the state of power on status.

Surface

AC 220-240V 50/60Hz

Max. 2000W

zone

Max. 1500W

zone

Control panel

Heating area

(210mm)

Power

Heating area

(180mm)

1. Heating zone selection controls

2. Power / Timer regulating key

3. keylock control

4. ON/OFF control

5. Timer control

Heating area

(140mm)

1500W

Size (mm)

590x520x622000W 2000W

Bad Good

WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in a fire.

When the hob is on, touch“ON/OFF” , all heating areas will be off. Another touch means the hob enters power

on status.

3. Place a suitable pan on the cooking zone that you wish to use.

• Make sure the bottom of the pan and the surface of the cooking zone are clean and dry.

4. Touching the heating zone selection control ,and a indicator next to the key will flash

• Select a heat setting by touching the “-“ or “+” control.

• If you don’t choose a heat setting within 1 minute, the Induction hob will automatically switch off. You will need

to start again at step 2.

• You can modify the heat setting at any time during cooking.

5、If the display flashes “ ” alternately with the heat setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centred on the cooking zone. No heating takes place unless there is a suitable pan on the cooking zone. The display will automatically turn off after 1 minutes if no suitable pan is placed on it.

Cooling fan

When the hob starts heating, the cooling fan will start work together. When heating area stops work,

cooling fan will keep working for additional 2 minutes then stop.

When you have finished cooking

1. Touching the heating zone selection control that you wish to switch off

2. Turn the cooking zone off by scrolling down to ”0” . Make sure the display shows”0”,then show”H”.

3. Turn the whole cooktop off by touching the ON/OFF control.

4. Beware of hot surfaces： “H” will show which cooking zone is hot to touch. It will disappear when the surface has

is still very high, do not let your fingers touch induction glass directly in case of scalds. Note: After use, switch off the hob element by its control and do not rely on the pan detector.

Locking the Controls

• You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are disabled. To lock the controls Touch the keylock control . The timer indicator will show “ Lo ” To unlock the controls

1. Make sure the Induction hob is turned on.

2. Touch and hold the keylock contro for 3s

3. You can now start using your Induction hob.

When the hob is in the lock mode,all the controls are disable except theON/OFF , you can always turn the induction hob off with the ON/OFF control in an emergency,but you shall unlock the hob first in the next operation

Over-Temperature Protection

A temperature sensor equipped can monitor the temperature inside the Induction hob. When an excessive temperature is monitored, “E3” or “E5” is shown on display, the hob will be off, internal cooling fan keep running until internal temperature is cool, then the hob will re-start heating.

Detection of Small Articles

When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other small item (e.g. knife, fork, key) has been left on the hob, the hob automatically go on to standby in 1 minute. The fan will keep cooking down the induction

hob for a further 2 minute.

Auto Shutdown Protection

Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to

turn off your cooking. The default working times for various power levels are shown in the below table:

When the pot is removed, the induction hob can stop heating immediately and the hob automatically

switch off after 1minutes.

People with a heart pace maker should consult with their doctor before using this unit.

Using the Timer

• You can set it to turn one cooking zone off after the set time is up.

• You can set the timer up to 99 minutes.

cooled down to a safe temperature. It can also be used as an energy saving function if you want

to heat further pans, use the hotplate that is still hot. Note:When “H” is shown on display, although he hob is off, but the temperature of induction glass

Power level

Default working timer (hour)

1828384454647

2.082.092.0

Setting the timer to turn one cooking zone off

Cooking zones set for this feature will:

1. Touching the heating zone selection control that you want to set the timer for.

2. Touch timer control , The minder indicator will start flashing and “30” will show in the timer display，And red point near the heating zone will be lighted

3. Set the time by touching the “-“ or “+” control of the timer Hint: Touch the “-“ or “+” control of the timer once will decrease or increase by 1 minute. Touch and hold the ”-“ or “+” control of the timer will decrease or increase by 10 minutes.

4. Touching the “-“ , when the “00” shows in the minute display, the timer is cancelled, .

5. When the time is set, it will begin to count down immediately. The display will show the remaining time

and the timer indicator flash for 5 seconds.

6. When cooking timer expires, the corresponding cooking zone will be switch off automatically.

7. Timer for multiple heating areas delay off, the shortest delay off time will be shown on display. If want to check remained delay off time of other heating area, you should press button for different heating area. NOTE: After setting delay off time, the time shown on display means heating area with red point twinkling.

Other cooking zone will keep operating if they are turned on previously.

Cooking Guidelines

Take care when frying as the oil and fat heat up very quickly. At extremely high termperatures oil and fat will ignite spontaneously and this presents a serious fire risk.

Heat Settings

The settings below are guidelines only. The exact setting will depend on several factors, including your cookware and the amount you are cooking. Experiment with the induction hob to find the settings that best suit you.

Heat setting Suitability

1-2

● Delicate warming for small amounts of food

● Melting chocolate, butter, and foods that burn quickly

● Gentle simmering ● Slow warming

3-4 5-6 7-8

● Reheating ● Rapid simmering ● Cooking rice

● Pancakes

● Cooking pasta

● Stir-frying ● Searing ● Bringing soup to the boil ● Boiling water

Care and cleaning

1. Everyday soiling on glass (fingerprints, marks, stains left by food of non-sugary spillovers on the glass).

1)Switch the power to the cooktop off;

2)Apply a cooktop cleaner while the glass is still warm (but not hot!)

3)Rinse and wipe dry with a clean cloth or paper towel.

4)Switch the power to the cooktop back on.

NOTE:

● When the power to the cooktop is switched off, there will be no hot surface indication but the cooking zone may still be hot! Take extreme care.

● Heavy-duty scourers, some nylon scourers and harsh/abrasive cleaning agents may scratch to check if your

cleaner or scourer is suitable.

2. Boilovers, melts, and hot sugary spills on the glass

● Never leave cleaning residue on the cooktop: the glass may become stained.

Remove these immediately with a fish slice, palette knife or razor blade scraper suitable for induction glass cooktops, but beware of hot cooking zone surfaces:

1). Switch the power to the cooktop off at the wall.

2). Hold the blade or utensil at a 30°angle and scrape the soiling or spill to a cool area of the cooktop.

3). Clean the soiling or spill up with a dish cloth or paper towel.

4). Follow steps 2 to 4 for everyday soiling on glass above.

NOTE:

● Remove stains left by melts and sugary food or spillovers as soon as possible. If left to cool on the glass, they

may be difficult to remove or even permanently damage the glass surface.

● Cut hazard: then the safety cover is retracted, Use with extreme care and always store safely and out of rech

of children.

3. Spillovers on the touch controls

1). Switch the power to the cooktop off.

2). Soak up the spill

3). Wipe the touch control area with a clean damp sponge or cloth.

4). Wipe the arta completely dry with a paper towel.

5). Switch the power to the cooktop back on.

The cooktop may beep and turn Itself off, and the touch controls may not function while there is liquid on them.

NOTE:

Hints and Tips

1. The induction hob cannot be turned on.

2. The touch controls are unresponsive.

3. The touch controls are difficult to operate.

4. The glass is being scratched.

5. Some pans make crackling or clicking noises.

6. The induction hob makes a low humming noise when used on a high heat setting.

7. Fan noise coming from the induction hob.

8. Pans do not become hot and appears “ ” in the display.

9. The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is displayed (typically alternating with one or two digits in the cooking timer display).

Failure Display and Inspection

If an abnormality comes up, the induction hob will enter the protective state automatically and display corresponding protective codes:

Make sure you wipe the touch control area dry before turning the cooktop back on.

May be there is no power: Make sure the induction hob is connected to the power supply and that it is switched on. Check whether there is a power outage in your home or area. If you’ve checked everything and the problem persists, call a qualified technician.

The controls are locked: Unlock the controls. See section using your induction cooktop for instructions.

There may be a slight film of water over the controls or you may be using the tip of your finger when touching the controls:

Make sure the touch control area is dry and use the ball of your finger when touching the controls.

Tough-edged cookware. Unsuitable, abrasive scourer or cleaning products being used: Use cookware with flat and

smooth bases. See choosing the right cookware. See “Care and cleaning”.

This may be caused by the construction of your cookware (layers of different metals vibrating differently): This is normal, but the noise should quieten down or disappear completely.

This is caused by the technology of induction cooking: This is normal, but the noise should quieten down or disappear

completely when you decrease the heat setting.

A cooling fan built into your induction hob has come on to prevent the electronics from overheating. It may continue to run

even after you’re turned the induction hob off: This is normal and needs no action. Do not switch the power to the

induction hob off at the wall while the fan is running.

The induction hob cannot detect the pan because it is not suitable for induction cooking. The induction hob cannot detect the pan because it is too small for the cooking zone or not properly centred on it: Use cookware suitable for induction cooking. See section ‘Choosing the right cookware’.

Centre the pan and make sure that its base matches the size of the cooking zone.

Technical fault: Please not down the error letters and numbers, switch the power to the induction hob off at the wall, and contact a qualified technician.

Problem

The appliance

does not work

During heating,

the unit stop work.

F3 F4

F9 FA

Possible causes What to do

Please check the main power is normal; if the leakage protection switch is off; if there is a blown fuse,

Break in power supply

Delay off timer activates.

No pan or pan unsuitable

Input power too low

Input power too high

Thermistor of coil short circuit. Thermistor of coil open circuit.

Too high temperature of IGBT thermistor.

Too high temperature

of coil thermistor.

IGBT thermistor short circuit IGBT thermistor open circuit

replace it with a new one; if the main power is normal, check if the plug is connect with socket appropriately; If the hob is wire connection type, disconnect the power, check if the wire is loose; disconnect the power, check if main plug is off; Exclude above reasons, should be appliance fault, send

it to service center for repairing.

Please check if set delay off function. If set delay off function, the unit will stop once delay off time out.

No pan, please put proper pan. PCB synchronization or drive circuit fault, please send the

appliance to service center for repairing.

Low voltage, voltage of the main power is less 180V. Please check if voltage of the main power is normal. Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault, please send the

unit to service center for repairing.

High voltage, voltage of the main power exceeds 250V. Please check if voltage of the main power is normal. Once voltage of the main power returns normal, re-start the unit. Voltage of PCB fault, please

send the unit to service center for repairing.

Sensor of coil thermistor connection error. Or detection part of PCB coil thermistor failure,

send to service center for reparing.

Too high temperature of IGBT thermistor, air outlet is blocked. Open air outlet, re-start the unit. If still unsolved, it is possible that cooling fan connection error, cooling fan damaged, or drive circuit of fan failure, send to service center for repairing. IGBT temperature sensor open circuit /short circuit. Temperature detection part of PCB IGBT failure, send to service center for repairing.

Too high temperature on induction glass surface, please check if there is no water in pan. After treatment, connect with power again. If still unsolved, it is possible that sensor of cooktop failure, send to

service center for repairing.

Senor of IGBT thermistor connection error. Or detection part of IGBT PCB sensor failure,

send to service center for repairing.

The above are the judgment and inspection of common failures.

Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.

Installation

This hob installation with 2 ways:

1. Desktop installation Do not place any item arond and botton of the hob. Do not block the air inlet and outlet

2. Built-in Installation

Selection of installation equipment

Cut out the work surface according to the sizes shown in the drawing.

For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.

Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface material to avoid

larger deformation caused by the heat radiation from the hotplate. As shown below:

L(mm) W(mm) H(mm) D(mm) A(mm) B(mm) X(mm)

590 520 62 58 560 490 50 mini

Under any circumstances, make sure the Induction cooker hob is well ventilated and the air inlet and outlet are not blocked. Ensure the Induction cooker hob is in good work state. As shown below

Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 760mm.

A(mm) B(mm) C(mm) D E

760 50 mini 20 mini Air intake Air exit ≥5mm

Note: There must be have a 560x5mm holes on front

>2cm

of cooker top position E, to dissipate heat air.

>35mm

<50mm

Before you install the hob, make sure that

• the work surface is square and level, and no structural members interfere with space requirements

• the work surface is made of a heat-resistant material

• if the hob is installed above an oven, the oven has a built-in cooling fan

• the installation will comply with all clearance requirements and applicable standards and regulations

• a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring,

mounted and positioned to comply with the local wiring rules and regulations.

The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements)

• the isolating switch will be easily accessible to the customer with the hob installed

• you consult local building authorities and by-laws if in doubt regarding installation

• you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces surrounding the hob.

When you have installed the hob, make sure that

• the power supply cable is not accessible through cupboard doors or drawers

• there is adequate flow of fresh air from outside the cabinetry to the base of the hob

• if the hob is installed above a drawer or cupboard space, a thermal protection barrier is installed below the base of the hob

• the isolating switch is easily accessible by the customer

Before locating the fixing brackets

The unit should be placed on a stable, smooth surface (use the packaging). Do not

apply force onto the controls protruding from the hob.

Brackets

Adjusting the bracket position Fix the hob on the work surface by screw 4 brackets on the bottom of hob(see

picture) after installation.

Adjust the bracket position to suit for different table top thickness.

Cautions

1. The induction hotplate must be installed by qualified personnel or technicians. We have professionals at your service.

Please never conduct the operation by yourself.

2. The hob will not be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer, as the

humidity may damage the hob electronics

3. The induction hotplate shall be installed such that better heat radiation can be ensured to enhance its reliability.

4. The wall and induced heating zone above the table surface shall withstand heat.

5. To avoid any damage, the sandwich layer and adhesive must be resistant to heat.

Connecting the hob to the mains power supply

This hob must be connected to the mains power supply only by a suitably qualified person.

Before connecting the hob to the mains power supply, check that:

1. the domestic wiring system is suitable for the power drawn by the hob.

2. the voltage corresponds to the value given in the rating plate

3. the power supply cable sections can withstand the load specified on the rating plate.

To connect the hob to the mains power supply, do not use adapters, reducers, or branching devices, as they can cause

overheating and fire.

The power supply cable must not touch any hot parts and must be positioned so that its temperature will not exceed 75˚C

at any point. Check with an electrician whether the domestic wiring system is suitable without alterations. Any alterations must only be

made by a qualified electrician. The power supply should be connected in compliance with the relevant standard,or a single-pole circuit breaker.the method

of connection is shown below.

WARMING:

Close the cable clamp after making the electrical connection. Close the terminal board cover by twisting it down.

CONNECTION DIAGRAM

Caution! Voltage of heating elements 220-240V

Caution! In the event of any connection the safety

Wire must be connected to the E terminal.

For 220-240V earthed one-phase connection, bridges

connect L terminals and terminals, safety wire to

④

⑤

②

①

②

①

④

⑤

Recommended

type of

connection lead

TERMINAL BOARD

• If the cable is damaged or to be replaced, the operation must be carried out the by after-sale agent with dedicated tools to

avoid any accidents.

• If the appliance is being connected directly to the mains an omnipolar circuit-breaker must be installed with a minimum

opening of 3mm between contacts.

• The installer must ensure that the correct electrical connection has been made and that it is compliant with safety

regulations.

• The cable must not be bent or compressed.

• The cable must be checked regularly and replaced by authorised technicians only.

This appliance is labeled in compliance with European directive 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE). By ensuring that this appliance is disposed of correctly, you will help prevent any possibledamage to the environment and to human health, which might otherwise be caused if were disposed of in the wrong way.

The symbol on the product indicates that it may not be treated as normal household waste.

DISPOSAL: Do not

dispose this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

It should be taken to a collection point for the recycling of electrical and electronic goods.

This appliance requires specialist waste disposal. For further information regarding the treatment, recover and recycling of this product please contact your local council, your household waste disposal service, or the shop where

you purchased it.

For more detailed information about treatment, recovery and recycling of this product, please contact your local cityoffice, your household waste disposal service or the shop where you purchased the product.