Haier HBS82-880 User Manual

HBS82-880

HBS82-880

Automatic Drum Washing Machine

Operation Manual

Table of Contents

Before using

Names of Parts--------------inside front cover
Matters Needing Attention--------------------1-3
Installation----------------------------------------4-5
Control Panel---------------------------------------6
Operational Functions------------------------6-7

During using

Program Selection--------------------------------8
Preparation-----------------------------------------9
Washing Methods---------------------------10-11

0020503555

Maintenance

Maintenance -------------------------------------12
Trouble Shooting--------------------------------13
Technical Specification---- --------------------14
Wiring Circuit-------------------------------------15

Names of Parts

Detergent distributor

Door

Porthole

Power supply cable

Earth terminal

Back plate screw (3)

Drainage hose

Top

Operation button

program knob

Temperature knob

Drainage hose clip

Packing bolt (3)

Back plate

Caution and Warning symbols

For your saf ety, any instructions in this manual with this “Warning”
sign shall be strictly followed.

For your safety and to prevent damages to the washing machine,
any instructions in this manual with this “Stop” sign shall be
strictly followed.

This diagram may vary slightly with the layout of the washing machine you have just purchased due
to technical improvements.

Matters Needing Attention

Safety

1. A separate earthed socket is required for the
power supply. After installation of the washing
machine,the power plug should be accessible
during the normal wash.

2. Hold the plug and not the electric cable when
unplugging the washing machine.

3. Fuses in the power circuit should be rated
for 15A. Refer to a washing machine techni­cian or a Haier designated service point for
power cable replacement.

5. Do not use flammable detergent or dry clean­ing agent; do not use flammable spray in close
vicinity to the washing machine; do not remove
or insert the plug in the presence of flammable
gas.

7. Do not allow children play with the packing materials after unpacking.

4. For your safety, dry hands before touching
the washing machine and wear appropriate
footwear .

6. The door of the washing machine will be­come hot during the water heating process.
Avoid contact with the door during the heating
process. For safety, keep children away from
the washing machine.

1

1

Matters Needing Attention

8. The washing machine must not be used in
the open or in area of high moisture as water
droplets may form on electrical components,
Air dry the appliance if the washing machine
components become wet.

10. Keep away from heat sources and direct
sunlight to prevent plastic and rubber com­ponents from aging.

Use

9. The washing machine should be place in
a well ventilated area maintaing a space
between walls or furniture.

11. During installation, ensure that the elec­tric cable is not trapped by the washing ma­chine and avoid damage to the electric
cable.

1. Make sure that the washing machine is
securely connected to the water supply,
take the necessory precautions or con­tact the local service center if the con­nection is poor or there is a water
leakage.

2

2. After turning the power off, turn the pro­gram knob clockwise to set washing
program.

2

Matters Needing Attention

3. Never place heavy objects ,a heating
applianceor a water container on the top
panel of the washing machine.

5. Before washing, do up zippers, buttons ,laces
and repair damaged areas,underwear or small
articals should be placed in the laundry bag
or a pillowslip.
Do not wash clothes containing wire frames.

7. The door is fitted with a self-lock device
and will not open until 2~3 minutes after
the washing machine stops. Do not force
the door open. Do not open the door when
water level reaches the port hole.

4. Do not wash foam rubber or similar
sponge materials.

6. Do not open the detergent box during
the wash cycle.

8. After washing, turn off the tap to prevent
leakage; unplug the washing machine and
wipe clean the lower part of the port hole.

9. Keep the door slightly open when the washing machine is not being used. Never cover
the machine with a plastic sheet.

3

3

Installation

As shown in figure1 remove all the packing materials

(including the foam base).

Remove the packing screws as shown in figure 2.
The packing bolts protect the appliance from shock during
transportation The steps below should be followed before
using the appliance,

1. Remove the rear panel of the washing machine;

2. remove the three packing bolts from the rear panel of the
washing machine,the rubber hose and then the shock ab­sorption channel steel;

3. reinstall the back plate;

4. fill the holes left by the packing bolts with plastic plugs.

(Attention: the packing bolts and rubber hose should be kept
in a safe place for later use)

Fig 1

Fig 2

Adjusting the position of the washing machine .There are
adjustable feet under the bottom of the washing machine. Be­fore use, the washing machine should be adjusted, as shown in
figure 3, so that it is level.

4

Fig 3

4

Installation

Connection of water inlet hose and washing machine

100cm

80cm

1. Place the water inlet hose nut on the connector
of the water inlet valve.

2. slightly shake the water inlet hose nut to see if
it is tightly and properly fixed.

connector of water inlet valve

Water drainage hose

The height of the terminal of the water drainage hose should
be between 80cm-100cm, the water drainage hose must be
securely placed on the clip on the back of the washing machine.

Use the water drainage support supplied as an accessory
for proper installation of the water drainage hose .fix the water
drainage hose support with waterproof sring.Do not use an
excessively long water drainage hose and contract the autho­rized technician if the water drainage hose needs to be
extended.the water drainage hose should not be extended
more than250cm.(longer extension will result in concurrent
water inflow and outflow).The diameter of the extension hose
should be the same as the original hose.
caution:water drainage hose must not be immersed in water.
the original and extension hoses should be tightly connected .

Connection of power supply

water inlet hose nut

100cm

80cm

Check the following items before connection to the power supply.

The socket conforms to the maximun power load(The maximum current load of the

socket and power supply cable should not be less than 15A).

Power supply voltage conforms to the required value.

The power supply socket and the plug of the washing machine compatib le ,if the y are
compatible ,Refer to a washing machine technician or a Haier designated service point
for power cable replacement.The washing machine should be connected to an earth
before use.

Supplementary earth cable should not be necessary if the socket is connected to the

earth.

Supplementary earth cable should be installed on the upper back of the washing

machine andconnected to an earth if the power supply socket has no earth connection.

5

5

Control Panel

4

1

3

2

D

E

C

F

G

A Washing program

Turn the knob clockwise to set the desired wash program .
Caution: Turn off the power and turn the program knob clockwise
for setting desired wash program.

B Washing temperature

Turn the knob clockwise to set the desired temperature.
Temperatures between 30
lected when the knob is set at *.

O

C-90OC can be setted , Cold wash is se-

D

E

C

B

A

F

B

G

A

C Detergent distributor

Program discription are printed on the handle of the detergent
distributor,there are three detergent compartments numbered 1,2,3
Box 1: Pre-washing detergent
Box 2: Standard washing - extra-fast washing
Box 3: Softening agent, adjusting agent, perfume
Besides, there is a separate bleaching powder box 4. In case of
bleaching, put this box into compartment 1; remove this box from
compartment 1 if pre-washing is chosen. If bleaching is required,
place box 4 after the pre-washing is finished.

6

4

2

1

3

6

Operational Functions

D No spin button

When this button is pressed, the spin cycle will be spared but water
drain is still available. This function is useful for hard ironing fabrics,
such as chemical fiber and wool fabrics.

E Economic wash button

Pressing this button will reduce the consumption of water during
bleaching under intense wash. It is recommended that this
program be used when doing a small laundry load.
Do not forget to reduce the amount of detergent used.

F Power button

ON

OFF

Press the button ,washing machine will working;release the button,
the washing machine will stop.

ON

OFF

G Power light

The light will illuminates when the power supply is connected.

7

7

Program Selection

15

20

20

45

22.5

5

12.5

5

10

5

25

10

7.5

7.5

NOTE: “o”means softener liquid detergent canbe added when necessary. “ ”means detergent can
be added when necessary. “

”means no detergent can be added.

8

25

10

7.5

7.5

x

8

Preparation

1. Power supply

Plug in the power supply

220V~/50Hz.

4. Detergent selection

Only special low foam detergent
should be used in automatic drum
washing machine, form blended or
wool fabrics special detergent
should be used. dry cleaning solvent
should not be used such as
trichhloroethylene or alike (caution :
load the required amount of deter­gent only).

2. W ater supply

Turn on the tap ensure that the water is clear.
Caution: Before staring the washing machine turn on the
water faucrt to ensure that the water faucet and the water
inlet hose are connected correctly and do not leak.

3. Laundry treament

sort out clothes according to type and extent of dirt.
There are three types of clothes: cotton, synthetical and
woolen (silk) fabrics.

separate white clothes from colored. If whites and
coloreds are combined for one load, make sure the
coloreds are colorfast.

-Remove all objects from pockets that may cause dam­age to the machine, such as keys and coins.

-Clothing with frayed edges or yarns should be put in a
wash bag or special bag before washing.

-Repaire damaged clothing,lose buttons or damaged zips
and hooks before washing.

-Bed sheets and table ware should be loosely loaded
and not folded.

This washing machine is for household use and de­signed for mechanically washable clothes. When
washing, separate unwashable clothes with reference to
clothes labels.

9

9

Washing Methods

1. Laundry loading

Evenly load the laundry in the washing
machine and then tightly close the door
of the washing machine
Note: 1) When first using the washing ma­chine, let it run unloaded for one program
to prevent the laundry from being tainted
by oil or dirty water from the washing ma­chine. 2) Do not overload the washing ma­chine.

(cotton 950g)

Blended
fabric clothes
(800g)

(cotton

300g)

Single bed sheets

(cotton 800g)

Reference loading

Overalls

shirt

blankets (3000g)

2. Use of detergent

Pull out the detergent drawer, put required detergent, softening
agent and bleaching agent into the corresponding boxes. Push
back the drawer gently.
Caution: 1) Do not add liquid detergent into box 1 and 2

2) For pre-washing program, detergent should
be added to both box 1 and 2; for other
programs, do not add detergent to box 1

3) Do not overuse softening agent as this may
damage artificial fabrics.

Woolen

Jeans (800g)

Pajamas (200g)

Shirts (300g)

Underwear

(blended fabrics 70g)

Socks

(blended fabrics 50g)

Jackets

(cotton 800g)

3. Washing program setting

Set the wash program correctly in accordance with the laundry load.the methods for set­ting wash programs are indicated on the handle of the distributor on the washing machine.
turn the program knob clockwise to the desired program.
Caution: Turn off the power before setting the wash program.

10

10

Washing Methods

4. Washing temperature Setting

Set the washing temperature as required, otherwise, set at position * when heating is not
needed.

5. Selecting the function button

Select function buttons as required (refer to the directions printed on the operation
panel) ,otherwise keep all the button released.

6. W ashing

Press the power button and the washing machine will automatically commence
the programmed washing process.

7. End

11

Wait 2-3 minutes after the washing process is finished, press the power button again to cut off

the power supply. Open the door to take out the laundry. Turn off the tap and unplug the
washing machine.

Additional information
Energy and water saving during wash process

1. Collect clothes for one full wash load.

2. Do not overload the washing machine.

3. Pre-wash heavily soiled clothes.

4. Reduce the amount of detergent or choose fast or minimal washing programs for lightly
soiled clothes dirty.

5. Choose a proper washing temperature. Only exceed 60

6. Do not use more detergent than required.

7. Softening agent makes clothes feel softer and easier to iron.

O

C for heavily soiled clothes.

11

Maintenance

1. Turn of the water and electricity supply
after every wash. Open the door to pre­vent the formation of moisture and odors.
If the washing machine is left idle for a
long period, drain any remaining water in
the machine and replace the drainage
hose.

3. Clean the detergent compartment
regularly. For the detergent compartment
similar to figure (a), raise the compartment
slightly to remove and replace after cleaning.

Fig (a)

2. Unplug the machine during cleaning and
maintenance. Use a soft cloth dampened with
soapy liquid to clean the machine case and rub­ber components. Do not use corrosive or abra­sive chemicals or solvents.

4. Cleaning the Filter (once a month)

Press the lower edge of the filter compartment
cover to open; (Fig1-2)
Remove the filter by turning counterclockwise;
(Fig3)
Flash clean with running water;
Filter replacement is the reverse of removal. Cau­tion: Attention shall be paid to ensure that the fil­ter is replaced correctly to avoid possible leakage.

fig.1

fig.2

fig.3

5. To prevent block­ages to the water sup­ply or the ingress of
contaminants, clean
the water inlet and in­let water filter
regularly.

7. If the washing machine is left idle
for a long period turn off the water
and electricity supply and open the
door slightly to prevent the formation
of moisture and odors.

12

6. If the machine is to be moved a distance location,
replace the vibration mounting locks which were re­moved during installation as shown below.

Remove the
back cover.

Replace the rubber
plugs.

Tighten the bolts with the
spanner provided.

Insert the bolts.

Replace the back
cover.

12

Trouble shooting

The following circumstances do not constitute problems. Do not contact the main­tenance service until the problem has been confirmed.

Problem

The washing machine fails to operate

Washing machine does not fill
with water

The water supply and
drainage do not stop

Drainage failure

Strong vibration during spin

Possible Cause

Poor connection to power supply
Power failure
Door is not properly closed
Machine has not been switched on

Water is not turned on
Water pressure is less than 0.05MPa
The inlet hose is kinked
Water supply failure
The program knob is not properly set
The door is not properly closed

Check that the height of the water hose is below

80cm

Drainage hose is blocked
Drainage hose end is below 100cm above the

floor level

Some packing fixing bolts removed

Washing machine on a uneven surface

13

Operation stops before completion
of the wash cycle

Excessive foam in the drum

Water or electricity failure

The detergent is not a low foam type

Excessive detergent has been used

13

Technical Specification

Model

Item

Power supply

Maximum working current (A)

Water pressure (MPa)

Washing power (W)

Spinning power (W)

Washing program

Heating power (W)

Size (HXDXW) (mm)

HBS82-880

220V~/50Hz

10

0.05

330

650

15

1950

850x550x595

P 1

HBS82-880

Weight (kg)

14

72

14

Wiring Circuit

I1: Power Switch EVC,EVP,EVL: Water valve
I2: Economic wash Switch P1,P2: Pressure Switch
I3: No spin Switch THR: Adjustable Thermastat
MR: Door Lock D: Drain Pump
TM: Timer motor MC,ML: Motor
H:Heating Element C: Capacitance

I3: No spin Switch

I2: Economic wash
Switch

1515