Haier HBF1055TVE, HBF855TVE User Manual

Page 1
Automatic Drum
Washing Machine
HBF1055TVE HBF855TVE

Table of Contents
Before using
Names of Parts---------------------------------inside front cover Matters Needing Attention-------------------------------------1-3 Installation---------------------------------------------------------4-5 Control Panel--------------------------------------------------------6 Operational Functions-----------------------------------------6-7
During using
Program Selection-------------------------------------------------8 Preparation----------------------------------------------------------9 Washing Methods--------------------------------------------10-11
Other Function----------------------------------------------------12
Maintenance
Maintenance ------------------------------------------------------13 Trouble Shooting-------------------------------------------------14
Wiring Circuit------------------------------------------------------15
Technical Specification---------------------------------- --------16
Page 2
Names of Parts
Washing Allocating box
Wash Door
Observing Glass Window
Power supply cable
Table Cover
Program Knob
Spin speed selector knob
Operation Button
Earth terminal
Back plate screw (3)
Drainage hose
Drainage hose clip
Packing bolt (3)
Back plate
Caution and Warning symbols
For your safety, any instructions in this manual with this "Warning" sign
shall be strictly followed.
For your safety and to prevent damages to the washing machine, any
instructions in this manual with this "Stop" sign shall be strictly followed.
This diagram may vary slightly with the layout of the washing machine you have just purchased due
to technical improvements.
Page 3
Matters Needing Attention
ƽ
Safety
1. A separate earthed socket is required for the power supply. After installation of the washing machine,the power plug should be accessible during the normal wash.
3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni­cian or a Haier designated service point for power cable replacement.
2. Hold the plug and not the electric cable when unplugging the washing machine.
4. For your safety, dry hands before touch­ing the washing machine and wear appropri­ate footwear .
5. Do not use flammable detergent or dry cleaning agent; do not use flammable spray in close vicinity to the washing machine; do not remove or insert the plug in the presence of flammable gas.
7. Do not allow children play with the packing materials after unpacking.
6. The door of the washing machine will be­come hot during the water heating process. Avoid contact with the door during the heat­ing process. For safety, keep children away from the washing machine.
1
Page 4
Matters Needing Attention
ƽ
Use
2
Page 5
Matters Needing Attention
3. Never place heavy objects ,a heating applianceor a water container on the top panel of the washing machine.
5. Before washing, do up zippers, buttons , laces and repair damaged areas,under­wear or small articals should be placed in the laundry bag or a pillowslip.
Do not wash clothes containing wire frames.
4. Do not wash foam rubber or similar sponge materials.
6. Do not open the detergent box during thewashcycle.
7. The door is fitted with a self-lock device and will not open until 2~3 minutes after the wash­ing machine stops. Do not force the door open. Do not open the door when water level reaches the port hole.
9. Keep the door slightly open when the washing machine is not being used. Never cover the
machine with a plastic sheet.
8. After washing, turn off the tap to prevent leakage; unplug the washing machine and wipe clean the lower part of the port hole.
3
Page 6
Installation
As shown in figure1 remove all the packing materials
ƽ
(including the foam base). Upon opening of the package, water drops may be seen on
the plastic bag and the porthole. This in normal phenomenon resultingfrom water test in the factory.
Remove the packing screws as shown in figure 2.
ƽ
The packing bolts protect the appliance from shock during trans­portation The steps below should be followed before using the appliance,
1. Remove the rear panel of the washing machine;
2. Remove the three packing bolts from the rear panel of the wash­ing machine,the rubber hose and then the shock absorption chan­nel steel;
3. Reinstall the back plate;
4. Fill the holes left by the packing bolts with plastic plugs. (Attention: the packing bolts and rubber hose should be kept in a safe place for later use)
Fig 1
Adjusting the position of the washing machine .There are ad-
ƽ
justable feet under the bottom of the washing machine. Before use, the washing machine should be adjusted, as shown in figure 3, so that it is level.
Fig 2
Fig 3
4
Page 7
Installation
Connection of water inlet hose and washing machine
H
.
HOT
hot
Waterdrainagehose
The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine.
Use the water drainage support supplied as an accessory for proper installation of the water drain­age hose .fix the water drainage hose support with waterproof sring.Do not use an excessively long wa­ter drainage hose and contract the authorized tech­nician if the water drainage hose needs to be extended.the water drainage hose should not be ex­tended more than250cm.(longer extension will result in concurrent water inflow and outflow).The diam­eter of the extension hose should be the same as the original hose. caution:water drainage hose must not be immersed in water.the original and extension hoses should be tightly connected .
H
.
100cm
80cm
Connection of power supply
Check the following items before connection to the power supply.
The socket conforms to the maximun power load(The maximum current load of the socket and
power supply cable should not be less than 15A).
Power supply voltage conforms to the required value.
The power supply socket and the plug of the washing machine compatible,if they are compat­ible ,Refer to a washing machine technician or a Haier designated service point for power cable replacement.The washing machine should be connected to an earth before use.
Supplementary earth cable should not be necessary if the socket is connected to the earth.
Supplementary earth cable should be installed on the upper back of the washing machine
andconnected to an earth if the power supply socket has no earth connection.
5
Page 8
SOAK
PAUSE/START
EXTRA RINSE
MAX
LOW
SPIN
MAX
LOW
SPIN
MODIFIERS
SPIN
NO
NORMAL
LOW
MAX
CYCLE CELECTOR
Turn the knob at "0", then turn off the power and
turn the program knob for setting desired wash program.
The program knob will not rotate with the programmed washing
process.
Spin speed selection knob
By turning this knob,the required spinning speed can be selected.
The maximum speed will vary when a different program is selected.
SPIN
NO
NORMAL
LOW
MAX
Page 9
Operational Functions
Extra Rinse Button
Pause/Start Button
Soak Button
Press this button,the washing machine will not drain before the final spin-drying cycle.a soaking cycle will be started,and the inner drum will rotate once every 4 minutes(at both directions).If you want to spin the laundry, press this button again ,the program will continue until it ends.
If press this button,an addtional rinse operation will be activated before the softening cycle is reached.
When the electric cable of the washing maching is plugged and a program is selected, after the washing spinning speed function is set,lightly press this button,the operation will start. During a wash cycle,press this button lightly,the operation will pause.Press it again to resume operation.
7
Page 10
Program Selection
Program Setting Laundry
Prewash
Silk
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
Very heavy soil
Heavy
Heavy soil
Normal
Soiled cotton
Non-fade and medium
Light
soiled cotton Fading and medium
Delicate
soiled cotton Non-fade heavily
Normal
soiled chemical fiber Non-fade and medium
Light
soiled chemical fiber Fading and medium
Delicate
soiled chemical fiber Non-fade heavily soiled
Normal
woolen fabrics Fading and medium
Delicate
soiled woolen fabrics Non-fade heavily soiled
Normal
silk fabrics Fading and medium
Delicate
soiled silk fabrics
Quick
Medium-soiled lanudry
Rinse
Spin
Turn the program knob at "0" position and turn off the power. The wash
End
program ends and the washing machine stops operation.
Water
Temperature
Hot
Hot
Warm
Warm
Cold
Warm
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
*
NOTE: " " means softener liquid detergent canbe added when necessary.
" " means detergent can be added when necessary. " " means no detergent can be added.
8
Page 11
Preparation
2. Water supply
1. Power supply
Plug in the power supply 120V~/60Hz.
Turn on the tap ensure that the water is clear.
Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak.
4. Detergent selection
Only special low foam detergent should be used in automatic drum washing machine, form blended or wool fabrics special detergent should be used. dry cleaning solvent should not be used such as trichhloroethylene or alike (caution :load the re­quired amount of detergent only).
3. Laundry treament
sort out clothes according to type and extent of dirt.
ƽ
There are three types of clothes: cotton, synthetical and
woolen (silk) fabrics.
separate white clothes from colored. If whites and
ƽ
coloreds are combined for one load, make sure the
coloreds are colorfast.
-Remove all objects from pockets that may cause dam-
age to the machine, such as keys and coins.
-Clothing with frayed edges or yarns should be put in a
wash bag or special bag before washing.
-Repaire damaged clothing,lose buttons or damaged zips
and hooks before washing.
-Bed sheets and table ware should be loosely loaded and
not folded.
This washing machine is for household use and de-
ƽ
signed for mechanically washable clothes. When washing,
separate unwashable clothes with reference to clothes
labels.
9
Page 12
Washing Methods
1. Laundry loading
Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing machine, let it run un­loaded for one program to pre­vent the laundry from being tainted by oil or dirty water from the washing machine. 2) Do not overload the washing machine.
2. Use of detergent
Overalls
ƽ
(cotton 950g)
ƽ
Blended fabric clothes (800g)
shirt
ƽ
(cotton
300g)
ƽ
Single bed
sheets
(cotton 800g)
Reference loading
ƽ
Woolen blankets
(3000g)
ƽ
Jeans (800g)
ƽ
Pajamas (200g)
ƽ
Shirts
(300g)
ƽ
Underwear
(blended fabrics 70g)
ƽ
Socks
(blended fabrics 50g)
ƽ
Jackets
(cotton 800g)
Pull out the detergent drawer, put required detergent, soften­ing agent and bleaching agent into the corresponding boxes. Push back the drawer gently. Caution: 1) Do not add liquid detergent into box 1 and 2
2) For pre-washing program, detergent should be added to both box 1 and 2; for other programs, do not add detergent to box 1
3) Do not overuse softening agent as this may
damage artificial fabrics.
3. Washing program setting
Set the wash program correctly in accordance with the laundry load. The methods for setting wash programs are indicated on the handle of the distributor on the washing machine. Turn the program knob to the desired program. Caution: If you want to choose another program, first t
urn the program knob at "0", then
turn off the power and turn the program knob for setting desired program.
10
Page 13
Washing Methods
4. Selecting the function button
Select function buttons as required (refer to the directions printed on the control panel) , otherwise keep all the button released.
5. Washing
Press the PAUSE/START button and the washing machine will automatically commence the pro
Caution: The program knob will not rotate with the programmed washing process.
grammed washing process.
6. End
Wait 2-3 minutes after the washing process is finished , press the power button again to cut off the power supply.Open the door to take out the laundry.Turn off the tap and unplug the washing machine.
Caution: When the washing program finishes, the door lock light will glitter before the door can be opened.
Additional information
Energy and water saving during wash process
1. Collect clothes for one full wash load.
2. Do not overload the washing machine.
3. Prewash heavily soiled clothes.
4. Reduce the amount of detergent or choose fast or minimal washing programs for lightly soiled clothes dirty.
5. Choose a proper spin speed.
6. Do not use more detergent than required.
7. Softening agent makes clothes feel softer and easier to iron.
11
Page 14
Other Functions
1. Power-off memory funtion:
This machine has a power-off menmory funtion. In case of abrupt power failure
or the power must be cut off during a program cycle, the present settings will be saved, and operation will resume when the power is switched on again.
2. Trouble messages: judge the malfunctions from door lock light
Error 1: The door lock light does not illuminate.
Cause: Door is not properly shut. Correction: Shut the door properly.
Error 2: The door lock light glitters 2 times and stops 4 seconds repeatedly.
Cause: Drainage error, water not emptied within 4 minutes. Correction: Clean the filter and check the drain hose for blockage. If error still
exists, please contact the maintenance personnel.
Error 3: The door lock light glitters 5 times and stops 4 seconds repeatedly.
Cause: Water level not met in 8 minutes. Correction: Make sure that tap is turned on, and water pressure is normal.
If problem still exists, please contact the maintenance personnel.
Error 4: The door lock light glitters 6 times and stops 4 seconds repeatedly.
Cause: Timing control silicon damage. Correction: Contact the maintenance personnel.
Error 5: The door lock light glitters 7 times and stops 4 seconds repeatedly.
Cause: Motor overheat protection or damage. Correction: Contact the maintenance personnel.
Error 6: The door lock light glitters 8 times and stops 4 seconds repeatedly.
Cause: Water exceeds protective level. Correction: Contact the maintenance personnel.
12
Page 15
Maintenance
1. Turn of the water and electricity supply af­ter every wash. Open the door to prevent the formation of moisture and odors. If the wash­ing machine is left idle for a long period, drain any remaining water in the machine and re­place the drainage hose.
3.
2. Unplug the machine during cleaning and maintenance. Use a soft cloth dampened with soapy liquid to clean the machine case and rubber components. Do not use corro­sive or abrasive chemicals or solvents.
4. To prevent blockages to the water supply or the ingress of contaminants, clean the water inlet and inlet water filter regularly.
6. If the washing machine is left idle for a long period turn off the water and electricity supply and open the door slightly to prevent the formation of moisture and odors.
13
5. If the machine is to be moved a distance location, replace the vibration mounting locks which were re­moved during installation as shown below.
Remove the back cover.
Tighten the bolts with a spanner.
Replace the rubber plugs.
Insert the bolts.
Replace the back cover.
Page 16
Trouble shooting
The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed.
Problem
The washing machine fails to operate
Washing machine does not fill with water
The water supply and drainage do not stop
Possible Cause
ƽ
Poor connection to power supply
ƽ
Power failure
ƽ
Door is not properly closed
ƽ
Machine has not been switched on
ƽ
Water is not turned on
ƽ
Water pressure is less than 0.05MPa
ƽ
The inlet hose is kinked
ƽ
Water supply failure
ƽ
The program knob is not properly set
ƽ
The door is not properly closed
ƽ
Check that the height of the water hose is below 80cm
Drainage failure
Strong vibration during spin
Operation stops before comple­tion of the wash cycle
Excessive foam in the drum
ƽ
Drainage hose is blocked
ƽ
Drainage hose end is over 100cm above the
floor level
ƽ
Some packing fixing bolts removed
ƽ
Washing machine on a uneven surface
ƽ
Water or electricity failure
ƽ
The detergent is not a low foam type Excessive detergent has been used
ƽ
14
Page 17
Technical Specification
Model
Item
HBF1055TVE
Power supply
Maximum working current (A)
Water pressure (MPa)
Washing power (W)
Spinning power (W)
Spinning speed (r/min)
Washing program
Size (HXDXW) (mm)
120V~/60Hz
13
0.05 P 1
400
1200
1000
15
850x550x595
15
Weight (kg)
76
Page 18
Wiring Circuit
Motor
MR
EVF
EVP
MRN
MRL
MRC
M1
CN2-1
CN2-3
CN2-5
CN2-7
M3
M2
CON7 CON5
CN2-9
EVC
M4
M5
CON8
M6
CON6
M7
CN3-3
M8
CN3-1
PCB
C
CON4
12
13
14
11
P
CN2-11 CON3 CN3-5 CN3-7
PS
CON2
CON1
FA
N
G
L
PCB-Printed Circuit Board
EVP,EVF-Cold water Valve EVC-Hot Water Valve
FA-Interference Suppresser
MR-Door Lock SW-Power Switch PS-Drain Pump
P-Pressure Switch
16
Loading...