Haier HA1000TE, HA600TE, HA800TE User Manual
Automatic Drum
Washing Machine
HA1000TE HA800TE HA600TE
Table of Contents
Before using
Names of Parts---------------------------------inside front cover
Matters Needing Attention-------------------------------------1-3
Installation---------------------------------------------------------4-5
Control Panel--------------------------------------------------------6
Operational Functions-----------------------------------------6-7
During using
Program Selection-------------------------------------------------8
Preparation----------------------------------------------------------9
Washing Methods--------------------------------------------10-11
Other Function----------------------------------------------------12
Maintenance
Maintenance ------------------------------------------------------13
Trouble Shooting-------------------------------------------------14
Wiring Circuit------------------------------------------------------15
Technical Specification---------------------------------- --------16
Names of Parts
Washing Allocating box
Wash Door
Observing Glass Window
Power supply cable
Table Cover
Operation Button
Program Knob
Temperature knob
Earth terminal
Back plate screw (3)
Drainage hose
Drainage hose clip
Packing bolt (3)
Back plate
Caution and Warning symbols
For your safety, any instructions in this manual with this "Warning" sign
shall be strictly followed.
For your safety and to prevent damages to the washing machine, any
instructions in this manual with this "Stop" sign shall be strictly followed.
This diagram may vary slightly with the layout of the washing machine you have just purchased due
to technical improvements.
Matters Needing Attention
ƽ
Safety
1. A separate earthed socket is required
for the power supply. After installation of
the washing machine,the power plug
should be accessible during the normal
wash.
3. Fuses in the power circuit should be rated
for 15A. Refer to a washing machine technician or a Haier designated service point for
power cable replacement.
2. Hold the plug and not the electric cable
when unplugging the washing machine.
4. For your safety, dry hands before touching the washing machine and wear appropriate footwear .
5. Do not use flammable detergent or dry
cleaning agent; do not use flammable
spray in close vicinity to the washing
machine; do not remove or insert the plug
in the presence of flammable gas.
7. Do not allow children play with the packing materials after unpacking.
6. The door of the washing machine will become hot during the water heating process.
Avoid contact with the door during the heating process. For safety, keep children away
from the washing machine.
1
Matters Needing Attention
ƽ
Use
2
Matters Needing Attention
3. Never place heavy objects ,a heating
applianceor a water container on the top panel
of the washing machine.
5. Before washing, do up zippers, buttons ,
laces and repair damaged areas,underwear or small articals should be placed
in the laundry bag or a pillowslip.
Do not wash clothes containing wire
frames.
4. Do not wash foam rubber or similar sponge
materials.
6. Do not open the detergent box during
the wash cycle.
7. The door is fitted with a self-lock device and
will not open until 2~3 minutes after the washing machine stops. Do not force the door
open. Do not open the door when water level
reaches the port hole.
9. Keep the door slightly open when the washing machine is not being used. Never cover the
machine with a plastic sheet.
8. After washing, turn off the tap to prevent
leakage; unplug the washing machine
and wipe clean the lower part of the port
hole.
3
Installation
As shown in figure1 remove all the packing materials
ƽ
(including the foam base).
Upon opening of the package, water drops may be seen on
the plastic bag and the porthole. This in normal phenomenon
resultingfrom water test in the factory.
ƽ
Check attachments and materials.
Fig 1
Name
Qty
Model
HA1000TE
HA800TE
HA600TE
Remove the packing screws as shown in figure 2.
ƽ
The packing bolts protect the appliance from shock during transportation The steps below should be followed before using the
appliance,
1. Remove the rear panel of the washing machine;
2. Remove the three packing bolts from the rear panel of the washing machine,the rubber hose and then the shock absorption channel steel;
3. Reinstall the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: the packing bolts and rubber hose should be kept in a
safe place for later use)
Operational
manual
1
Quality
certificate
Water
hose
1
Drainage
holder
11
Plastic
plugs
3
Adjusting the position of the washing machine .There are ad-
ƽ
justable feet under the bottom of the washing machine. Before use,
the washing machine should be adjusted, as shown in figure 3, so
that it is level.
4
Fig 2
Fig 3
Loading...