Haier HA1000 User Manual

HA1000\HM1000
Automatic Drum Washing Machine
Table of Contents
Before using
Names of Parts--------------inside front cover Matters Needing Attention--------------------1-3 Installation----------------------------------------4-5 Control Panel---------------------------------------6 Operational Functions------------------------6-7
During using
Program Selection--------------------------------8 Preparation-----------------------------------------9 Washing Methods---------------------------10-11
Maintenance
Maintenance -------------------------------------12 Trouble Shooting--------------------------------13 Technical Specification-------------------------14
Names of Parts
Detergent distributor
Operation button
Door
Porthole
Power supply cable
Earth terminal
Back plate screw (3)
Drainage hose
Top
program knob
Temperature knob
Drainage hose clip
Packing bolt (3)
Back plate
Caution and Warning symbols
For your safety, any instructions in this manual with this “Warning”
sign shall be strictly followed.
For your safety and to prevent damages to the washing machine,
any instructions in this manual with this “Stop” sign shall be
strictly followed.
This diagram may vary slightly with the layout of the washing machine you have just purchased due
to technical improvements.
Matters Needing Attention
Safety
1. A separate earthed socket is required for the power supply. After installation of the washing machine,the power plug should be accessible during the normal wash.
2. Hold the plug and not the electric cable when unplugging the washing machine.
3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni­cian or a Haier designated service point for power cable replacement.
5. Do not use flammable detergent or dry clean­ing agent; do not use flammable spray in close vicinity to the washing machine; do not remove or insert the plug in the presence of flammable gas.
7. Do not allow children play with the packing materials after unpacking.
4. For your safety, dry hands before touching the washing machine and wear appropriate footwear .
6. The door of the washing machine will be­come hot during the water heating process. Avoid contact with the door during the heating process. For safety, keep children away from the washing machine.
1
Matters Needing Attention
8. The washing machine must not be used in the open or in area of high moisture as water droplets may form on electrical components, Air dry the appliance if the washing machine components become wet.
10. Keep away from heat sources and direct sunlight to prevent plastic and rubber com­ponents from aging.
Use
9. The washing machine should be place in a well ventilated area maintaing a space between walls or furniture.
11. During installation, ensure that the elec­tric cable is not trapped by the washing ma­chine and avoid damage to the electric cable.
1. Make sure that the washing machine is se­curely connected to the water supply,take the necessory precautions or con-tact the local service center if the con-nection is poor or there is a water leakage.
2
2. After turning the power of f, turn the program knob clockwise to set washing program.
Matters Needing Attention
3. Never place heavy objects ,a heating applianceor a water container on the top panel of the washing machine.
5. Before washing, do up zippers, buttons ,laces and repair damaged areas,underwear or small articals should be placed in the laundry bag or a pillowslip. Do not wash clothes containing wire frames.
7. The door is fitted with a self-lock device and will not open until 2~3 minutes after the washing machine stops. Do not force the door open. Do not open the door when water level reaches the port hole.
4. Do not wash foam rubber or similar sponge materials.
6. Do not open the detergent box during the wash cycle.
8. After washing, turn off the tap to prevent leakage; unplug the washing machine and wipe clean the lower part of the port hole.
9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet.
3
Installation
As shown in figure1 remove all the packing materials (including the foam base).
Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during transportation The steps below should be followed before using the appliance,
1. Remove the rear panel of the washing machine;
2. Remove the three packing bolts from the rear panel of the washing machine,the rubber hose and then the shock ab­sorption channel steel;
3. Reinstall the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: the packing bolts and rubber hose should be kept in a safe place for later use)
Fig 1
Fig 2
Adjusting the position of the washing machine .There are adjustable feet under the bottom of the washing machine. Be­fore use, the washing machine should be adjusted, as shown in figure 3, so that it is level.
4
Fig 3
Installation
Connection of water inlet hose and washing machine
1. Place the water inlet hose nut on the connector of the water inlet valve.And rotate it clockwise to screw onto the connector
2. slightly shake the water inlet hose nut to see if it is tightly and properly fixed.
connector of water inlet valve
Water drainage hose
The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine.
Use the water drainage support supplied as an accessory for proper installation of the water drainage hose .fix the water drainage hose support with waterproof sring.Do not use an excessively long water drainage hose and contact the autho­rized technician if the water drainage hose needs to be extended.the water drainage hose should not be extended more than250cm.(longer extension will result in concurrent water inflow and outflow).The diameter of the extension hose should be the same as the original hose. caution:water drainage hose must not be immersed in water. the original and extension hoses should be tightly connected .
Connection of power supply
water inlet hose nut
100cm
80cm
Check the following items before connection to the power supply.
The socket conforms to the maximun power load(The maximum current load of the socket and power supply cable should not be less than 15A).
Power supply voltage conforms to the required value. The power supply socket and the plug of the washing machine are compatible,if they are not
compatible ,Refer to a washing machine technician or a Haier designated service point for power cable replacement.The washing machine should be connected to an earth before use.
Supplementary earth cable should not be necessary if the socket is connected to the
earth.
Supplementary earth cable should be installed on the upper back of the washing
machine andconnected to an earth if the power supply socket has no earth connection.
5
Control Panel
HA\HM1000
80
A Washing program
Turn the knob clockwise to set the desired wash program . Caution: Turn off the power and turn the program knob clockwise for setting desired wash program.
B Washing temperature
Turn the knob clockwise to set the desired temperature. Temperatures between 30OC-90OC can be setted , Cold wash is se­lected when the knob is set at *.
C Detergent Dispenser.
The detergent dispenser is divided into 3 compartments marked 2,A,C 2 Wash detergentExcept liquid detergent A Softeners, conditioners, perfumes C Bleach
6
80
Operational Functions
D Cold Wash BUtton.
Press it you need a cold wash. Release it you need a heating wash. For cotton, water. can be heated to 90 •. For synthetic, to 60and for wool, to 40•.
E No spin button
When this button is pressed, the spin cycle will be spared but water drain is still available. This function is useful for hard ironing fabrics, such as chemical fiber and wool fabrics.
F Power button
Press the button ,washing machine will start working;release the button, the washing machine will stop.
ON
OFF
G Power light
The light will illuminate when the power supply is connected.
H Door Lock Light
Remember that only when the washer doesn’t work, we can open the door. After the washing program finish,after 3 minutes, when the self-lock meter turn off, we can open the door.
7
Program Selection
8
Preparation
1. Power supply
Plug in the power supply
220V~/50Hz.
4. Detergent selection
Only special low foam detergent should be used in automatic drum washing machine, form blended or wool fabrics special detergent should be used. dry cleaning solvent should not be used such as trichhloroethylene or alike (caution : load the required amount of deter­gent only).
2. Water supply
Turn on the tap are ensure that the water is clear. Caution: Before staring the washing machine turn on the water faucet to ensure that the water faucet and the water inlet hose are connected correctly and do not leak.
3. Laundry Treatment
sort out clothes according to type and extent of dirt. There are three types of clothes: cotton, synthetical and woolen (silk) fabrics.
separate white clothes from colored. If whites and coloreds are combined for one load, make sure the coloreds are colorfast.
-Remove all objects from pockets that may cause dam­age to the machine, such as keys and coins.
-Clothing with frayed edges or yarns should be put in a wash bag or special bag before washing.
-Repaire damaged clothing,lose buttons or damaged zips and hooks before washing.
-Bed sheets and table ware should be loosely loaded and not folded.
This washing machine is for household use and de­signed for mechanically washable clothes. When washing, separate unwashable clothes with reference to clothes labels.
9
Washing Methods
1. Laundry loading
Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing ma­chine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing ma­chine. 2) Do not overload the washing ma­chine.
Overalls
(cotton 950g)
Blended fabric clothes (800g)
shirt (cotton
300g)
Single bed sheets (cotton 800g)
Reference loading
blankets (3000g)
2. Use of detergent
Pull out the detergent drawer, put required detergent, softening agent and bleaching agent into the corresponding boxes. Push back the drawer gently. Caution: 1) Do not add liquid detergent into box 2
2) For pre-washing program, detergent should be added to both box 2; for other programs, do not add detergent to box 1
3) Do not overuse softening agent as this may
damage artificial fabrics.
Woolen
Jeans (800g)
Pajamas (200g)
Shirts (300g)
Underwear
(blended fabrics 70g)
Socks
(blended fabrics 50g)
Jackets
(cotton 800g)
3. Washing program setting
Set the wash program correctly in accordance with the laundry load.the methods for set­ting wash programs are indicated on the handle of the distributor on the washing machine. turn the program knob clockwise to the desired program. Caution: Turn off the power before setting the wash program.
10
10
Washing Methods
4. Washing temperature Setting
Set the washing temperature as required, otherwise, set at position * when heating is not needed.
5. Selecting the function button
Select function buttons as required (refer to the directions printed on the operation panel) ,otherwise keep all the button released.
6. Washing
Press the power button and the washing machine will automatically commence the programmed washing process.
7. End
Wait 2-3 minutes after the washing process is finished, press the power button again to cut off the power supply. Open the door to take out the laundry. Turn off the tap and unplug the washing machine.
Additional information Energy and water saving during wash process
1. Collect clothes for one full wash load.
2. Do not overload the washing machine.
3. Pre-wash heavily soiled clothes.
4. Reduce the amount of detergent or choose fast or minimal washing programs for lightly soiled clothes dirty.
5. Choose a proper washing temperature. Only exceed 60
6. Do not use more detergent than required.
7. Softening agent makes clothes feel softer and easier to iron.
O
C for heavily soiled clothes.
11
Maintenance
1. Turn of the water and electricity supply after every wash. Open the door to pre­vent the formation of moisture and odors. If the washing machine is left idle for a long period, drain any remaining water in the machine and replace the drainage hose.
3. Clean the detergent compartment regularly. For the detergent compartment similar to figure (a), raise the compartment slightly to remove and replace after cleaning.
Fig (a)
2. Unplug the machine during cleaning and maintenance. Use a soft cloth dampened with soapy liquid to clean the machine case and rub­ber components. Do not use corrosive or abra­sive chemicals or solvents.
4. Cleaning the Filter (once a month)
Press the lower edge of the filter compartment cover to open; (Fig1-2) Remove the filter by turning counterclockwise; (Fig3) Flash clean with running water; Filter replacement is the reverse of removal. Cau­tion: Attention shall be paid to ensure that the fil­ter is replaced correctly to avoid possible leakage.
fig.1
fig.2
fig.3
5. To prevent block­ages to the water sup­ply or the ingress of contaminants, clean the water inlet and in­let water filter regularly.
7. If the washing machine is left idle for a long period turn off the water and electricity supply and open the door slightly to prevent the formation of moisture and odors.
12
6. If the machine is to be moved a distance location, replace the vibration mounting locks which were re­moved during installation as shown below.
Remove the back cover.
Replace the rubber plugs.
Tighten the bolts with the spanner provided.
Insert the bolts.
Replace the back cover.
Trouble shooting
The following circumstances do not constitute problems. Do not contact the main­tenance service until the problem has been confirmed.
Problem
The washing machine fails to operate
Washing machine does not fill with water
The water supply and drainage do not stop
Drainage failure
Strong vibration during spin
Possible Cause
Poor connection to power supply
Power failure
Door is not properly closed
Machine has not been switched on
Water is not turned on
Water pressure is less than 0.05MPa
The inlet hose is kinked
Water supply failure
The program knob is not properly set
The door is not properly closed
Check that the height of the water hose is below
80cm
Drainage hose is blocked
Drainage hose end is below 100cm above the
floor level
Some packing fixing bolts removed
Washing machine on a uneven surface
Operation stops before completion of the wash cycle
Excessive foam in the drum
Water or electricity failure
The detergent is not a low foam type
Excessive detergent has been used
13
Technical Specification
Item
Power supply
Maximum working current
Water pressure
Washing power
Spinning power
Washing program
Heating power
Size (HXDXW)
Model
(A)
(MPa)
(W)
(W)
(W)
(mm)
HA\HM1000
220V~/50Hz
10
0.05¡Ü P¡Ü 1 IPX4
330
650
12
1950
850x520x595
Weight
14
(kg)
68
14
Loading...