Haier HSU-12HEA03/R2, HSU-07HEA03/R2, HSU-09HEA03/R2, HSU-18HEA03/R2, HSU-22HEA03/R2 Operation Manual

...

Download

0010526880

Pleasereadthisoperationmanualbeforeusingtheairconditioner.

●

Keep this operation manual for future reference.

SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL

....................................................

1 2

................................................................

......................................................................

..........................................................

PARTS AND FUNCTIONS OPERATION MAINTENANCE

TROUBLE SHOOTING

CAUTIONS

Contents

....................................................

....................................................................

................................................................

......................................................................

..........................................................

Índice

PRECAUCIONES

COMPONENTES Y FUNCIONES

FUNCIONAMIENTO

MANTENIMIENTO

RESOLUCIÓN DE PROBLEMAS

....................................................

....................................................................

................................................................

......................................................................

..........................................................

Contenuti

AVVERTENZE PARTI E FUNZIONI FUNZIONAMENTO

MANUTENZIONE RISOLUZIONE DEI PROBLEMI

....................................................

....................................................................

................................................................

......................................................................

..........................................................

Table des matières

AVERTISSEMENTS PIÈCES ET FONCTIONS OPÉRATION MAINTENANCE

DÉPANNAGE

HSU-07HEA03/R2 HSU-09HEA03/R2 HSU-12HEA03/R2 HSU-18HEA03/R2

HSU-22HEA03/R2 HSU-24HEA03/R2

H2SM-(9+9)HEA03/R2 H2SM-(9+12)HEA03/R2

HSU-09HEA103/R2 HSU-12HEA103/R2

Outdoor Unit



Loading of the battery

 













Parts and Functions

Indoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Remote controller

Remove the battery cover;

Load the batteries as illustrated.

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

is in line with th

e" + "/"-";

Load the battery,then put on the cover again.

Inlet grille

Inlet

Air Purifying Filter

Outlet

Horizontal flap

Display board

(adjust up and down air flow Don't adjust it manually)

(adjust left and

ow)

Vertical blade

Emergency

Switch

Anion generator

(inside)

11.TIMER ON display

12.FAN SPEED display

LOW HI

MED AUTO

13. LOCK display

14. SWING display

Use to select CODE A or B which will be displayed on LCD.Please select A without special explanation.

1.CODE

7. MODE button

CLOCK button

SWING

When the remote controller

RESET

button

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change- over

wireless telephone is installed in the

ver is apt to be disturbed in receiving

the signals,

so the distance to the indoor unit should be shorter

type fluorescent lamp or room, the recei

Note:

Full display or unclear display during operation indicates the

ries have been used up.

Please change batteries.

If the remote controller can't run normally during operation, please

reload several minutes later.

batte

remove the batteries and

Remove the batteries in case unit won't be in usage for a long period.

If there are any display

after taking-out, just need to press reset key.

Hint:

appears abnormal,use a

sharp pointed article to

press this button to reset the

remote controller normal.

SLEEP display

10. ON/OFF button

6. HEALTH button

button

4.TIMER

button

Please be subject to the actual produce purchased the above picture is just from your reference

right air fl

Please be subject to the actual produce purchased the above picture is just from your reference

POWER/SOFT

3.LIGHT button

Control the lightening and extinguishing of the indoor

LED display board.

8. HOUR button

HEALTH display

17. Operation mode display

Operation mode

AUTO

FAN

COOL DRY

Remote controller

HEAT

19. POWER/SOFT display

20. Left/right air flow display

21. TEMP display

22. TIMER OFF display

23. CLOCK display

24. TEMP button

25. FAN button

26. HEALTH AIRFLOW button

27. SLEEP button

28. SET button

29. POWER/SOFT button

If pressed, the other buttons will be disabled Press it once again,

lock will be cancelled.

30. LOCK button

18.Singal sending display

TEMP

display

COOL display



HEAT display



ALTH display

Dry display









 



TIMER OFF display

TIMER ON display SLEEP display

AUTO display



Remote signal receiver

Display board



Singal receiver hole

 COOL display



HEAT display



TEMP display

Dry display









 















(If the unit which you purchased

has healthy function,follow it.

TIMER OFF display

TIMER ON display SLEEP display

If not,please ignore.)

Display board



HEALTH display



The following displays are not available:



The following functions and related displays are only

available for model HSU-22HEA03/R2ǃHSU-24HEA03/R2 :



Operation

Air Flow Direction Adjustment

AUTO COOL DRY FAN HEAT

2.Select operation mode

Press FAN button. For each press, fan speed changes as follows:

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

Press

button

Every time the button is pressed, temp.setting increase 1

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will decrease

rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

LOW

MED

AUTO

1. Unit start

Press ON/OFF on the remote controller, unit starts.



Clock set

Operation

Mode

AUTO

Display Board

Remote

Controller

Note

COOL

DRY

HEAT

FAN

nothing

In DRY mode, when room temperature becomes lower than temp.setting+2

C,unit will run intermittently

at LOW speed regardless of FAN setting.

Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature. air conditioner

automatically adjusts the fan speed

temperature.

When FAN is set to AUTO, the

according to room

In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled. In FAN mode,SLEEP operation is not available.

Vertical flap

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

(Auto swing)

1.Status display of air flow

When restart after remote turning off, the remote

memorize the previous

Move the vertical blade by a knob on air

to adjust left and right direction referring to Fig.

2.Left and right air flow adjustment

(manual)

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur

adjusted to left or

It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY

otherwise, condensate water might occur.

conditioner

temperature is below 16

C, do not use it in the

Test operation:

Use this switch in the test operation when the room

normal operation.

your finger from the switch: the cooling

Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice,

release

Test operation switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

Emergency operation and test operation

Pi Pi

at air outlet if all vertical louvers are

right.

mode ,

controller will automatically

Note:

set swing position.

Remote controller

Base Operation

Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press

change quickly.

After time setting is confirmed,press SET,

"AM "and "PM" stop flashing,while clock starts working.

or decrease 1min. If the

button is kept pressed,time will

will increase

POWER/SOFT

Emergency Operation:

Use this operation only when the remote controller is defective or lost.

When the emergency operation switch is pressed,the" Pi "sound is heard once

, which

the start of this operation.

In this operation, the system automatically selects

the

operation modes

,cooling or fan or heat,

according to the room temperature.

It is not possible to operate in dry mode.

Room

temperature

Operation mode

Designated temperature

Timer

mode

Air flow

ABOVE 23

BELOW 23

COOLING

HEAT

AUTOMATIC

(cooling only uint)

Room temperature

Operation

mode

Designated temperature

Timer mode

Air flow

BELOW 23

FAN

AUTOMATIC

means

POWER/SOFT

Operation

Sleep Operation

If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change.

5.Set the wind speed change when sleeping

Use of SLEEP function

Operation Mode

1. In COOL,DRY mode

SLEEP operation starts SLEEP operation stops

SLEEP operation starts

SLEEP operation stops

Approx.6hrs

1 hr

3 hrs

Rises 1OC

Rises 1

Rises 1OC

Temp.setting

Unit stop

In COOL, DRY mode

In HEAT mode

Decreases 2OC

Decreases 2

1 hr

In HEAT mode

In AUTO mode

4. In FAN mode

It has no SLEEP function.

Note

When TIMER function is set, the sleeping function can't be set up .After the sleeping function is set up

if user resets TIMER function, the sleeping function will be cancelled;the machine will be in the state of timing-on.

POWER/SOFT Operation

(1)

POWER Operation

(2)

SOFT Operation

To cancel POWER or SOFT operation The POWER / SOFT symbols on the remote controll will be disappeared after 15 minutes, the unit continues to run according to the original state. Press POWER/SOFT button again, POWER or SOFT disappears.

Note˖

HEALTHY Operation

Healthy Negative ions

Before going to bed,you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep.

After the unit starts,set the operation status, then press SLEEP button before which the clock must be adjusted and time being set.

1 hours after SLEEP mode starts,temp.will become 1 higher than temp.setting.After another 1 hours, temp.rises by 1 futher.The unit will run for further 6 hours then stops Temp. is higher than temp. setting so that room temperature won’t be too low for your sleep.

1 hours after SLEEP mode starts,temp will become 2 lower than temp.setting.After another 1 hours,temp decrease by 2 futher.After more another 3hours,temp.rises by 1 futher.The unit will run for further 3 hours then stops.Temp.is lower than temp. setting so that room temperature won’t be too high for your sleep.

The unit operaters in corresponding sleep mode adapted to the automatically selected operation mode.

The anion generator in the airconditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.

During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. During SOFT operation will cause effect of not too cool or not too warm.

When you need rapid heating or cooling, you can use this function. In COOL mode, fan speed automatically takes high speed of AUTO fan mode. In HEAT mode, fan speed antomatically takes high speed of AUTO fan mode.

You can use this function when silence is needed for rest or reading. In SOFT operation mode, fan speed antomatically takes low speed of AUTO fan mode.

Operation

Set clock correctly before starting TIMER operation.

1.After unit starts, select your desired operation mode.

2.Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:

BLANK

TIMER ON TIMER OFF TIMER ON-OFF

Then select your desired TIMER mode (TIMER ON or TIMER OFF or TIMER ON-OFF). " "or " "will flash.

3.Press / button to set time. It can be adjusted within 24 hours.

4.After setting correct time, press SET button to confirm " "or" " on the remote controller stops flashing.

5.Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function,when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved.

Timer On/Off On-Off Operation

All the products are in conformity with the following European provision:

- Low Voltage Directive 73/23/EEC

- Low Voltage Directive 2006/95/EC

-Electomagnetic CompatibilitY 89/336/EEC

-Electomagnetic CompatibilitY 2004/108/EC

ROHS

The products are fulfilled with the requirements in the directive 2002/95/EEC of the European parliament and of

council on the Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment (EU RoHS Directive)

WEEE

DISPOSAL REQUIREMENTS:

Your air conditioning product is marked with this symbol.This means that electrical and electronic

products shall not be mixed with unsorted household waste. Do not try to dismantle the system yourself : the dismantling of the air

EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS

1+2=

R410A

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Do not vent into the atmosphere.

Refrigerant type:R410A GWP* value:1975 GWP=global warming potential Please fill in with indelible ink,

• 1 the factory refrigerant charge of the product

• 2 the additional refrigerant amount charged in the field and

• 1+2 the total refrigerant charge on the refrigerant charge label supplied with the product. The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the stop value cover). A contains fluorinated greenhouse gases covered by the Kyoto Protocol B factory refrigerant charge of the product: see unit name plate C additional refrigerant amount charged in the field D total refrigerant charge E outdoor unit F refrigerant cylinder and manifold for charging

IMPORTANT INFORMATION REGARDING THE REFRIGERANT USED

In accordance with the directive 2002/96/CE of the European parliament, herewith we inform the consumer about the dis-

posal requirements of the electrical and electronic products.

conditioning system,treatment of the refrigerant, of oil and of other part must be done by a qualified installer in accordance

with relevant local and national legislation. Air conditioners must be treated at a specialized treatment facility for reuse, recycling and recovery. By ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and humen health. Please contact the installer or local authority for more information. Battery must be removed from the remote controller and disposed of separately in accordance with relevant local and nationl legislation.

Contains fluorinated greenhouse gases covered by the Kyoto Protocol

Healthy airflow Operation

1.Press ON/OFF to starting

Setting the comfort work conditions.

2.The setting of healthy airflow function

1).Press the button of healthy airflow

, appears on the

display. Horizontal airflow sending.

Avoid the airflow

blows direct to the body.

2).Press the button of healthy airflow again, appears on the displa

. Downward airflow sending.

Avoid the airflow

Note:

1.After setting the healthy airflow function, the position

grill is fixed.

4.In cooling and dry, using the air conditioner for a long

time under the high air humidity, condensate water may occur at the grille .

3.The cancel of the healthy airflow function Press the button of healthy airflow again,

the unit

goes on

working under the condition before the setting of healthy

airflow function.

Notice: Do not direct the flap by hand. Otherwise, the grille will run incorrectly. If the grille is not run correctly, stop

for a minute and then start, adjusting by remote controller.

blows direct to the body.

2.In heating, it is better to select the

3.In cooling, it is better to select the

mode. mode.

Maintenance

Setting of proper room temperature

Close doors and windows during operation

If the unit is not to be used for a long time, turn off the power supply main switch.

Use the timer effectively

Use the louvers effectively

Do not block the air inlet or outlet

Proper

temperature

During cooling operation prevent the penetration of

direct sunlight with

curtain or blind

OFF

Remote Controller Indoor Body

1.Open the lnlet Grille

2.Detach the standard air filter

3.Attach Air Purifying Filter

4.Attach the standard air filter

(Necessar

y installation)

5.Close the Inlet Grille

Close the Grille surely

Slide the knob slightly up

ward to

release the filter, then withdraw it.

Put air purifying filter appliances into the

right and left filter frames.

Detach old Air Purifying Filter

NOTE:

The photocatalyst air purifying filter will be solarized in fixed time. In normal family,

it will be solarized every 6 months.

Prop up the inlet grille by using a

small device named grille-support

ATTENTION:

Please keep the bacteria-killing medium air purifying filter in

avoid long time directly sunshine

when you stop using it,or its ability of sterilization will

reduced.

The bacteria-killing medium air purifying filter will be used for a long time,no need for replacement. But in the period of using them ,you should remove the dust frequently by

which located in the right side of

the indoor unit.

using vacuum cleaner or flaping them lightly,otherwise ,

its performance will be affected.

the cool and dry conditions

For Smart Use of The Air Conditioner

Replacement of Air Purifying Filter

The white side of the photocatalyst air purifying filter face outside,and the black side face the unit The green

side of the bacteria-killing medium air purifying filter face outside,and the white side face the unit.

Do not usewater,wipe the controller with a dry cloth.Do not use glass

cleaner or chemical cloth.

wipe the air conditioner by using a soft and dry cloth.For serious stains,

use a neutral detergent diluted with water.Wring the water out of the cloth before wiping,then wipe off the detergent completely.

Air Filter cleaning

Open the inlet grille by pulling it upward.

Remove the filter.

Clean the filter.

Attach the filter.

Close the inlet grille.

Push up the filter's center tab slightly until it is

from the stopper, and remove the filter do

wnw

ard.

Use a vacuum cleaner to remove dust, or wash the filter with water.After washing, dry the filter completely in the shade.

Attach the filter correctly so that the "FRONT" indication

facing to the front.Make sure that the filter is

fixed behind the stopper.If the right

attached correctly, that

Do not use the following for cleaning

Gasoline,benzine, thinner or cleanser

damage the coating of the unit.

Hot water over 40

C(104OF) may

discoloring or deformation.

Once every two weeks

cause

released

completely

and left filters are not

may cause defects.

the power supply cord and so on.

Do not install in the place where there is any

possibility of inflammable gas leakage around the unit.

3.Do not get the unit exposed

to vapor or oil steam.

Cautions

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.

Connect the earth cable.

earthing

WARNING

When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.

OFF

Use an exclusive power source with a circuit breaker

ENFORCEMENT

Connect power supply cord to the outlet completely

Use the proper voltage

Do not use power supply cord in a bundle.

Take care not to damage

the power supply cord.

1.Do not use power supply cord extended or connected in halfway

STRICT

ENFORCEMENT

STRICT

ENFORCEMENT

PROHIBITION

Do not start or stop the

operation by disconnecting

Do not channel the air flow directly at people, especially at infants or the aged.

Do not try to repair or reconstruct by yourself.

Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.

CAUTION

Take fresh air occasionally especially when gas appliance is running at the same time.

PROHIBITION

STRICT

ENFORCEMENT

Do not operate the switch with wet hand.

PROHIBITION

Do not install the unit near a fireplace or other heating apparatus.

Check good condition of the installation stand

Do not pour water onto the unit for cleaning

PROHIBITION

Do not place animals or plants in the direct path of the air flow

Do not place any objects on or climb on the unit.

Do not place flower vase or water containers on the top of the unit.

Do not insert objects into the air inlet or outlet.

PROHIBITION

STRICT ENFORCEMENT

Check proper installation of the drainage securely

WARNING

Trouble shooting

Normal Performance inspection

Noise is heard

Phenomenon

Cause or check points

The system

immediately.

Smells are generated.

Mist or steam are

Multiple

check

Poor cooling

When unit is stopped, it won't restart

elapsed to protect the system. When the electric plug is pulled out

and reinserted, the protection circuit

During unit operation or at stop, a swishing or gurgling noise may

(This noise is generated by refrigerant flowing in the system.)

During unit operation, a cracking noise may be heard.This noise is

temperature changes.

Should there be a big noise from

filter may be too dirty.

This is because the system circulates smells from the interior

During COOL or DRY operation,

This is due to the sudden cooling

Is power plug inserted? Is there a power failure? Is fuse blownout?

Is the air filter dirty?

Are there any obstacles before

Is temperature set correctly?

Are there some doors or

Is there any direct sunlight through the window during the

Are there too much heat sources or too many people in the room

In dry mode,

fan speed can’t be changed.

In DRY mode, when room temperature

setting+2

C,unit will run

regardless of FAN setting.

during cooling operation?

cooling operation?(Use curtain)

windows left open?

inlet and outlet?

Normally it should be cleaned every 15 days.

intermittently at LOW speed

becomes lower than temp.

indoor unit may blow out mist.

of indoor air.

air such as the smell of furniture, paint, cigarettes.

air flow in unit operation, air

generated by the casing expanding

or shrinking because of

be heard.At first 2-3 minutes after

unit start, this noise is more noticeable.

will work for 3 minutes to protect the

air conditioner.

immediately until 3 minutes have

Cautions

3. If the fuse of indoor unit on PC board is it with the type of

T. 3.15A/ 250V

outdoor

broken,change it with the type of

T.25A/250V

Do not obstruct or cover the ventilation

conditoner.Do not put fingers

inlet/outlet and

swing louver.

Do not allow children to play with the air

conditioner

case should children be

allowed to sit on the outdoor unit.

The refrigerating circuit is leak-proo f.

1.Applicable ambient temperature range:

Specifications

The machine is adaptive in following

situation

11 .The power plug and connecting cable

acquired the local

2. If the power supply cord is damaged, it

must be replaced

manufacturer

qualified

person.

4. The wiring method should be in line with

the local wiring

5. After installation, the power plug should

be easily reached.

6. The waste battery should be disposed

properly.

7. The appliance is not intended for use persons

without supervision.

8.Young children should be supervised

with

the appliance.

9. Please employ the proper power plug,

cord.

12.In order to protect the units,please turn 30 seconds

later, cutting off the power.

10. A breaker should be incorporated into

should be

should be not less than

3mm.

Cooling

Indoor

Maximum:D.B/W.B

D.B

Maximum:D.B

D.B

Mini

mum:D.B/W.B

Maximum:D.B/W.B Minimum:D.B/W.B

Outdoor

Indoor

Outdoor

Heating

32oC/23oC

C/18oC

C/-8oC

C/26oC

C/15oC

Outdoor

Maximum:D.B/W.B Mini

mum:D.B

C/18oC

-15

(INVERTER)

0oC

13.Please don't insert any sensor on 3-way

stop valve pipe

Mini

mum:

Mini

mum:

grille of the air

or any other things into the

.In no

or its service agent or a similar

broken,please

. If the fuse of

standard.

by young children or

to ensure that th

which fit into the

fixed wiring. The

all-pole switch and the distance

must have

off the A/C first,

fitting.

Before asking for service, check the following first.

blown out.

does not restart

by the

change

unit is

infirm

do not play

ower supply

breaker

between

its two contacts

attestation.

and at least

H2SM-(9+12)HEA03/R2

0.237

HSU-18HEA03/R2

HSU-24HEA03/R2

0.117

H2SM-(9+9)HEA03/R2

0.180

0.157

Remark: EMC testing of this model (HSU-24HEA03/R2) for the use of a magnetic ring power cord, so we recommend users touse the power cord with a magnetic ring.

HSU-12HEA103/R2

0.308

HSU-22HEA03/R2

0.271

Unidad interior

Recuerde que la ilustración anterior podría no reﬂejar ﬁelmente el producto adquirido y debe utilizarse únicamente como referencia.

Unidad exterior

TOMA DE SALIDA TUBOS DE CONEXIÓN Y CABLEADO

ELÉCTRICO

TOMA DE ENTRADA MANGUERA DE DRENAJE

Recuerde que la ilustración anterior podría no reflejar fielmente el producto adquirido y debe utilizarse únicamente como referencia.

Control remoto

POWER/SOFT

1. CÓDIGO Permite seleccionar el CÓDIGO Ao B. Una vez seleccionado, el código se mostrará en la pantalla LCD. Si no ha recibido instrucciones especíﬁcas, seleccione el código A.

2. Botón RESTABLECER Si el control remoto presenta alguna anomalía, introduzca un objeto puntiagudo a través del oriﬁcio para pulsar este botón y restablecer el control remoto.

3. Botón LUZ Controla la activación y desactivación de la iluminación del panel de indicadores LED de la unidad interior.

5. Botón RELOJ

6. Botón SALUDABLE

7. Botón MODO

8. Botón HORA

9. Botón OSCILACIÓN

10. Botón ENCENDIDO / APAGADO

11. Indicador de TEMPORIZADOR DE ENCENDIDO

12. Indicador de VELOCIDAD DE VENTILADOR

13. Indicador de BLOQUEO

14. Indicador de OSCILACIÓN

15. Indicador de la función SUEÑO

16. Indicador de la función SALUDABLE

17. Indicador de modo de funcionamiento

Modo de

funcionamiento

AUTOMÁTICO REFRIGERACIÓN SECO

CALEFACCIÓN

VENTILADOR

Control remoto

18. Indicador de envío de señal

19. Indicador de modo INTENSO / SUAVE

20. Indicador de dirección de ﬂujo de aire hacia la izquierda / derecha

21. Indicador de TEMPERATURA

22. Indicador de TEMPORIZADOR DE APAGADO

23. Indicador de RELOJ

24. Botón TEMPERATURA

25. Botón VENTILADOR

26. Botón FLUJO DE AIRE SALUDABLE

27. Botón SUEÑO

28. Botón ESTABLECER

29. Botón de modo INTENSO / SUAVE

30. Botón BLOQUEAR Al pulsarlo se deshabilitan los demás botones. Pulse de nuevo este botón para cancelar el bloqueo.

4. Botón TEMPORIZADOR Las siguientes funciones y los indicadores relacionados no están disponibles en este tipo de unidades:

Las siguientes funciones y los indicadores relacionados sólo están

Instalación de las baterías

1. Extraiga la cubierta de las baterías;

2. Instale las baterías como muestra la

ilustración. 2 baterías R-03, botón de restablecimiento (cilindro);

3. Asegúrese de que la polaridad

de las baterías coincide con los símbolos “+” / “-” al instalarlas;

Instale las baterías y vuelva a colocar de nuevo la cubierta.

Nota:

● La distancia entre el cabezal de transmisión de señal y el oriﬁcio del receptor debe ser inferiora7msinobstáculos.

● Si se instalan en la habitación lámparas ﬂuorescentes de activación electrónica o de tipo alterno, o bien teléfonos inalámbricos, el receptor podría resultar perturbado al recibir las señales, por lo que la distancia hasta la unidad interior deberá ser menor.

● Si se activan todos los indicadores de la pantalla o no es posible visualizarlos correctamente durante el uso, es señal de que las baterías se han agotado. Por favor, cambie las baterías.

● Si el control remoto no funciona normalmente durante su uso, extraiga las baterías y vuelva a instalarlas pasados unos minutos.

Componentes y funciones

BAJA

MEDIA

ALTA

AUTOMÁTICO

Rejilla de la toma de entrada

Toma de entrada

Toma de salida

Generador de aniones (interior)

Alerón horizontal (permite ajustar la dirección del ﬂujo de aire hacia arriba y hacia abajo; no lo ajuste manualmente)

Filtro puriﬁcador de aire

Interruptor de emergencia

Panel de indicadores

Oriﬁcio del receptor de señal

Pala vertical (permite ajustar la dirección del ﬂujo de aire hacia la izquierda y hacia la derecha)

Indicador de REFRIGERACIÓN

Indicador de la función SALUDABLE

Indicador del modo seco Indicador de TEMPORIZADOR

DE APAGADO Indicador de TEMPORIZADOR DE ENCENDIDO Indicador de la función SUEÑO

Sugerencia: Extraiga las baterías si no tiene intención de utilizar la unidad durante un periodo largo de tiempo. Si observa alguna pantalla extraña después de extraer las baterías, sólo necesitará pulsar el botón RESTABLECER.

Panel de indicadores

Indicador de CALEFACCIÓN

Indicador de TEMPERATURA

(Si la unidad que ha adquirido dispone de función saludable, préstele atención. De lo contrario, ignórelo).

Receptor de señal remota

Indicador de la función SALUDABLE

Indicador de TEMPORIZADOR DE APAGADO Indicador de TEMPORIZADOR DE ENCENDIDO Indicador de la función SUEÑO

Indicador de TEMPERATURA

Indicador del modo AUTOMÁTICO

Indicador de REFRIGERACIÓN

Indicador del modo seco

Indicador de CALEFACCIÓN

disponibles en el modelo HSU-22HEA03/R2ǃHSU-24HEA03/R2:

+ 20 hidden pages

Haier HSU-12HEA03/R2, HSU-07HEA03/R2, HSU-09HEA03/R2, HSU-18HEA03/R2, HSU-22HEA03/R2 Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual