Domestic Dishwasher
WQP12-AFM2
GB
`çÇÉW=MNOMRMQMPO^
Safety Is a Good Habit to Get Into
NOTICE
Carefully read the instructions contained in this manual,as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
- 73/23/EEC of 19/02/73(Low Voltage)and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing,check to make sure that the appli ance is not damaged.If in doubt,contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when bare foot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sockets;
* During installation,the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed,disconnect the appliance from the power supply.
- Keep detergents out of the reach of children,who must also be
kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors,not even if the
area in which it is installed is covered by a roof;it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open ,as this could
overturn the dishwasher.
- If the appliance malfunctions,turn off water supply to the appli
ance and disconnect the plug from the wall socket.Then,con
sult the section entitled, "Troubleshooting."If you cannot
solve the problem,contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing the
door lock.
- The appliance must be positioned so that the plug is accessible.
- The carpet must obstruct the opening when the appliance in stalling on the ground with carpet.
- If the supply cord is damaged , it must be replaced by a
special cord or assembly available from the manufacturer or
its service agent.
Close-up View (control panel)
A B C
F
A
ON-OFF Light
B
ON-OFF Button
Low Salt Indicator Light
C
E
D
Knob For Selecting Cycle
D
Handle For Opening Door
E
"Eco" Button
F
.1.
GB
Close-up View (Interior)
A
Upper Rack
B
Rack Height Adjustor
C
Top Spray Arm
D
Lower Rack
Technical characteristics
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorber power
Bottom Spray Arm
E
Washing Filter
F
Detergent and Rinse Aid Dispenser
G
Salt Container Cap
H
12 standard place settings
220-240V~ 50Hz
60 cm
60 cm
85 cm
0.03-0.6 MPa
2100W
GB
.2.
Salt
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher,deposits will form on the dishes
utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel(supplied) into the hole and intro duce about 2 kg of salt.It is normal for a small amount of water
to come out of the container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is equipped with a system to adjust the level of
salt consumption in function of the hardness of the water being
used in order to optimize and customize the level of salt consumption while keeping it to a minimum.
To adjust salt consumption level , follow these instructions:
- Unscrew the cap on the salt container;
- On the container there is an arrow (see figure to the side).If
necessary,turn the arrow in the anti-clockwise direction from
the "-" setting to the "+" setting based on the hard ness of the
water being used.
- It is highly recommended that the table be consulted when
making adjustments .
The salt container should be filled after about every 30 wash cycles.
To prevent the formation of rust,load the salt just before beginning a wash cycle.
Water Hardness
Clarke
degrees
014
NQPS
PSTN
[TN
.3.
ºdH
MNT
NUQQ
QRUV
[UV
mmol/l
MNIT
NIUQIQ
QIRUIV
[UIV
Selector
position
L
=?J?
jba
?H?
Salt
consumption
(Grams/cycle)
M
OM
QM
SM
Autonomy
(cycles/2kg)
L
SM
QM
OR
GB
Detergent and Rinse Aid
Detergent
Detergent specifically intended for use with dishwashers must
be used.The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table ".The detergent dispenser is located on the inside panel
the door.
Loading the detergent
To open the "A" cover on the dispenser,press the "B" button.The
detergent for the wash cycle should be poured into the "C"
compartment.
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.
C
A
Rinse Aid
This product makes dishes sparkle and helps them to dry without spotting.The dispenser is located on the inside panel of the
door and should be filled after every 80 wash cycles.
Loading the Rinse Aid
Regardless of the type detergent dispenser installed on your
appliance,you must proceed as indicator below when loading
the rinse aid.
To open the dispenser,turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid,making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dose adjustor,located beneath the "C" cap, with
a screwdriver.There are 6 different settings; the normal dosage
setting is 3.
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs , the
dosage adjustor should be turned to a higher setting.
If the dishes have white streaks,turn the dosage adjustor to a
lower setting.
B
Notice:To facilitate closing the cover, remove any excess
detergent on the edges of the dispenser.
C
F
C
GB
.4.
Loading the Dishwasher
Before placing the dishes in the dishwasher, remove the large food
particle to prevent the filter from becoming clogged,which results
in reduced performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they be allowed to soak before they
are washed.This will eliminate the need for extra wash cycle.
Pull out the rack to facilitate loading the dishwasher.
How to Use the Lower Rack
We recommend that you place the items which are the most difficult to clean items on the lower rack:pots ,lids,serving dishes and
bowls,as shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots,serving bowls,etc.must always be placed top down.
- Deep pots should be slanted to allow the water to flow out.
- The silverware basket can be doubled(see fig.A) so that only
one section may be used when the silver ware load is light. This
also makes space for additional pots and pans on the bottom
rack.
- Silverware should be placed in the silverware basket with the
handles at the bottom;if the rack has side baskets,the spoons
should be located individually into the appropriate slots.Espe cially
long utensils should be placed in the horizontal position at the
front of the upper rack.
Lower Rack Upper Rack
Load for 12 Standard Settings
How to Use the Upper Rack
The upper rack is designed to hold more delicate and lighter
dishware,such as glasses,coffee and tea cups and saucers,as well
as plates,small bowls and shallow pans(as long as they are not
too dirty).
Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height.(see fig.B)
fig.A
1
2
3
4
fig.B
.5.
GB
Starting the Appliance
Starting a wash cycle
- Make sure that the plug for the appliance is inserted into the wall
socket.
- Make sure that the water supply is turned on to full pressure.
- Load the dishwasher (see the section entitled,"Loading the
Dishwasher").
- Pour in the detergent (see the section entitled,"Salt,Dergent and
Rinse Aid").
- Turn the knob located on the right of the control panel in the
clockwise direction until the number or symbol for the cycle sec
tion entitled,"Wash Cycle Table").
- Press the ON-OFF button,and the ON-OFF light will turn on.At
this point,the wash cycle will begin.
Important:
In general, it is not advisable to open the door while the machine
is working. Care must be taken if the door is opened during the
hot phase or immediately after a programm has finished as steam
may escape.
Cancelling or modifying a wash cycle setting
Press the ON-OFF button and the ON Light will turn off. Rotate
the knob in the clockwise direction to the desired cycle setting
(see the section entiled,"Starting a wash cycle...").Then,turn the
dishwasher back on using the ON-OFF button.
At the end of the wash cycle
When the knob stops turning and is aligned with a STOP mark
(see figure),the cycle has finished.Turn off the appliance using
the ON-OFF button,turn off the water supply and open the door
of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid
handling the dishes and utensils while they are still hot and more
susceptible to breakage.They will also dry better.
Wash Cycle adjustment Buttons
============
======Button
============
This button(see "close-up View - Control Panel",letter"F")is used
for normally dirty dishes,pots and pans.It is standard daily cycle.
GB
.6.
Wash Cycle Table
Cycle Button
Heavy Duty
Heavy Duty
Normal
Wash
Cycle Selection
Information
Very dirty dishes,pots and pans
(not to be used with delicate
items).
Very dirty dishes,pots and pans
(not to be used with delicate
items).
Normally dirty dishes,pots and
pans .Standard daily cycle.
Description of
Cycle
Pre-wash with hot water.
Extended wash at 65
Rinse with cold water.
Rinse with hot water.
Drying.
Pre-wash with hot water.
Extended wash at 55
Rinse with cold water.
Rinse with hot water.
Drying.
Extended wash at 65
Rinse with cold water.
Rinse with hot water.
Drying.
.
.
.
Detergent Rinse
Aid
30 g
30 g
30 g
Normal Wash
IEC-EN 5MOQO
Rinse
Rapid Wash
Soak
Normally dirty dishes,pots and
pans .Standard daily cycle.
For dishes that need to be
rinsed and dried only.
Economic,fast cycle to be used
to on not very dirty dishes right
after they are used. No drying
cycle.
Pre-wash of dishes, pots and
pans while waiting for the load to
be complete after the subsequent
meal.
.
.
Extended wash at 55
Rinse with cold water.
Rinse with hot water.
Drying.
Rinse with cold water.
Rinse with hot water.
Drying.
Short wash at 55
Cold rinse.
Short cold wash to prevent food residue from drying on the dishes .
30 g
15 g
ERF
.7.
GB
Energy Saving Tips
- It is important to try and run the dishwasher when it is fully
loaded to save on enery.In order to prevent odours from form
ing and food from caking onto the dishes,you can run the soak
cycle.
- Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.
How to Keep Your Dishwasher in Shape
- Use the right amount of detergent: if you use too much detergent,
the result will not be cleaner dishes,but,rather,a greater nega
tive impact on the enviroment.
- There is no untility in rinsing dishes ,cookware and untensils
before placing them in the dishwasher.
After Every Wash
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odours are not
trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove the
plug from the socket.Do not run risks.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products.Rather, use only a
cloth and warm soap water.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and a little white vinegar,or a cleaning products made specifically for dishwasher.
When You Go on Holiday
When you go on holiday,it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket ,turn off the water supply and leave the door of the
appliance slightly ajar.This will help the seals last longer and prevent odours from forming within the appliance.
Moving the Appliance
If the appliance must be moved,try to keep it in the vertical position.
If absolutely necessary,it can be positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is
food that remains trapped in the seals.Periodic cleaning with a
sponge will prevent this from occuring.
GB
.8.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must be
cleaned.
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle.For this reason ,it is
a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the"A"semi-circular filter
and cup under running water.To remove the filter assembly,pull
on the cup handle in the upward direction. The entire filter assembly (made up of the "A" semicircular filter and the"B" fine
filter)should be cleaned at least once a month.To clean the filter
and the fine filter,use a cleaning brush .Then,reassemble the filter parts as shown in the figures below and reinsert the entire
assembly in the dishwasher,positioning in its seat and pressing
downward.
The dishwasher must never be used without the filters.Improper
replacement of the filters may reduce level of the appliance and
damage dishes and utensils.
Cleaning the Spray Arms
It may happen that food particle become encrusted on the sprayer
arms and block the hole. Check the sprayer arms periodically
and clean them when needed. (see "Close up view [interior]",
letters C-E ).
A
B
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter(see figure 1/A) located on
the outlet of the water supply tap.
After turning off the water tap, unscew the end of the water supply hose,remove the filter and clean it carefully under running
water.Then,return the filter to its place and tighten the water supply hose back into position.
Troubleshooting
It may occur that the dishwasher does not function or does not
function properly.Before calling for assistance,Iet us see what
can be done first:have you forgot to press one of the buttons or
to perfom an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is
connected properly;
- the water supply to the house on and has
sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
- the water is turned on and the hose is
connected properly;
- the water supply to the house on and has
sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
If,despite all these checks,the dishwasher still does not function
and/or the problem persists,contact the nearest authorised service centre and provide them with the following information:
- the nature of the problem;
- the model type number (Mod...)and the serial number (S/N...),
which are indicated on the plate located on the side of the inner
part of the door.
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
.9.
GB
Installation
Positioning the Appliance
Position the appliance in the desired location.The back should
rest against the wall behind it,and the sides,along the adjacent
cabinets or wall.The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned,adjust the feet (screwing them
in or out) to adjust the dishwasher,making it level.In any case,
the appliance should not be inclined more than 2.If the appliance is level,it will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see fig.1/
A).Some models have an "Acquablock" water supply pipe (see
fig.1/B) with filter in the threaded inlet.
If the water pipes are new or have not been used for an extended
period of time,let the water run to make sure that the water is
clear and free of impurities.If this precaution is not taken,there is
a risk that the water inlet can get blocked and damage the
appliance.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm,or let it run into the sink,making sure to avoid bending or
crimping it.Use the speical plastic support that comes with the
appliance (see fig .2).The free end of the hose must be at a
height between 40 and 100 cm and must not be immersed in
water.
fig.2
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system,heating system),as long
as it does not exceed a temperature of 60.
In this case,the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
Fig.1/ B
Fig.1/A
Attention:
The special plastic hose support must be solidly fastened to
the wall to prevent the drain hose from moving and allowing
water to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate
(located on the stainless steel inner door of the appliance) and
that the electrical system is sized for the maximum voltage on
the rating plate,insert the plug into an electrical socket which is
earthed properly (the earthing of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug,replace the plug ,rather than using adpators or the like as they could cause overheating and
burns.
GB
.10.
Installation
Diagram
Loading...