Haier ESAM055-C User Manual

0010552362

ESAM055-C

7-8

7-8

9-13

10
10

11-13

1
1
2
4
4
5
5
6

7

14-15

15-16

17

5

2. MODE Set Switch

2-way

airflow

control paneleasy access filters

6

TEMPERA TURE

65

FAN ONLY

SPEED

POWER

7

8
9

10

MAX
COOL

LOWHI

OFFON

Fig. # 1

4

3
2

1

MIN

COOL

7

POWER Turns air conditioner off.
SPEED "LOW" Low speed fan operation with cooling or not.
SPEED "HI" High speed fan operation with cooling or not.

This automatically controls the temperature of indoor air. Turn the knob
so that arrow points to the cooler marks for more moderate cooling.

Normal Fan

1. T urn the SPEED mode switch to the "HI" or the "LOW" setting.

2. Set the thermostat control to the temperature mark "FAN ONL Y".

Normal cooling

1. T urn the SPEED mode switch to the "HI" or the "LOW" setting.

2. Set the thermostat control to the desire temperature (the mid-point
is a good starting position).
If the room temperature is not satisfactory after a reasonable time, adjust
the control to a warmer setting, as appropriate.

Maximum cooling

1. Turn the SPEED mode switch to the "HI" setting

2. Set the thermostat control to the MAX COOL temperature mark.

Quieter operation

1. Turn the SPEED mode switch to the "LOW" setting.

2. Set the thermostat control as needed.

CAUTION:

1

2

Also when you shut off the air conditioner wait for 3 minutes
before turning it on again.

3

8

9

short screws 13/32"

wood screws 31/32"

top rail

window seal gasket

10

ASSEMBLE
CURTAINS/TOP RAIL

Install top rail with 3 short
screws13/32".

Insert the side curtains into the
top and bottom rails of the air
conditioner. F asten the curtains
to the unit with 8 short screws
13/32".

ESAM055-C

3

5

25

3

12

5
2

13

5
1

33

5
1

22

2
7

12

16

9

18

16

3

13

8

11

2

1. This unit is designed for installation in standard double hung windows
with actual opening widths of 22
must open sufficiently to allow a clear vertical opening of 14
bottom of the sash to the window stool.

2. If storm window presents interference, fasten a 2
included) (OUTER SILL) to the inner window sill across the full width of
the sill. The wood strip should be thick enough to raise the height of
the window sill so that the unit can be installed without interference by
the storm window frame (STORM WINDOW FRAME) or wood strip
(OUTDOORS) to help condensation to drain properly to the outside.

3. Install a second wood strip (approximately 6
same thickness as first strip) in the center of the outer sill flush against
the back off the inner sill. This will raise basepan angle .

4. If the distance between STORM WINDOW FRAME and WOOD STRIP
MOUNTED ON TOP OF INNER SILL is more than 1
strip are not necessary.

to 36 . The upper and lower sash

from the

wide wood strip(not

long by 3/2 wide and

, two of wood

INNER

SILL

I
N
D
O
O
R
S

WOOD STRIP
MOUNTED ON
TOP OF INNER SILL

INNER

SILL

I
N
D
O
O
R
S

1 MAX.

WOOD STRIP
FOR BASEPAN
ANGLE

OUTER

SILL

3/4 CLEARANCE

OUTER

SILL

O
U
T
D
O
O
R
S

STORM
WINDOW FRAME

O
U
T
D
O
O
R
S

LOCATING UNIT IN
WINDOW

Open the window and mark center line on the
center of the inner sill.

INNER SILL

INDOOR SIDE

CENTER LINE

ATTACH BASEPAN
ANGLE

Install the basepan angle behind the inner window sill, with
the short side of basepan angle as shown. Use the 2 short
screws13/32" provided.
The basepan angle helps to hold unit securely in place.
Be sure to place basepan angle edge flush against back
of inner sill.

INNER SILL

OUTER SILL

SHORT SIDE

OUTSIDE

BASEPAN ANGLE

SHORT SCREW13/32"

CENTER LINE

INSIDE

8

8

12

INSTALL THE AIR CONDITIONER
IN THE WINDOW

Carefully lift the air conditioner and slide it into the open
window. Make sure the bottom guide of the air conditioner
drops into the notches of the basepan angle.
While steadying the air conditioner ,carefully bring the
window sash down behind the upper guide of the air
conditioner.

WINDOW FRAME

UPPER GUIDE

ABOUT 1/4

INSTALL THE SEAL GASKET
AND SASH LOCK

Extend the side curtains to fill the
window opening using 4 wood screws
31/32" to secure them.
Cut the seal gasket to the window
width. Stuff the sash seal between the
glass and the window to prevent air
and insects from getting into the room.
Fasten the basepan angle, using a
short screw13/32".

BASEPAN ANGLE

SHORT SCREW13/32"

WOOD SCREW31/32"

BOTTOM GUIDE

BASEPAN ANGLE

WINDOW SEAL GASKET

13

TEMPERATURE

6

5

7

4

8

3

9

2

10

1

MAX

MIN

COOL

COOL

FAN ONLY

LOW

PEED

OFF

POWER

Always unplug your air conditioner before cleaning.

The air filter behind the front grille should be checked and
cleaned at least once every 2 weeks or more often if necessary.

To remove:

1. Open the inlet grille downward by pulling out the top of the inlet grille.

2. Remove the air filter from the front grille assembly by pulling the air filter
up slightly.

3. Clean the filter with warm, soapy water below 40oC(104oF).

4. Rinse and gently shake the water from the filter and let it dry before replacing
it.

DO NOT use your air conditioner without the air filter in place.

To clean the front panels or the cabinet DO NOT use harsh
chemicals, abrasives, ammonia, chlorine, bleach, concentrated
detergents, solvents or metal scouring pads.

Always use a soft cloth dampened with water or mild soap
and water solution to wipe the front of the cabinet.

14

15

(see page 7)

(see page 13)

16