Haier ESA412NE, ESA410NTC, ESA410NT, ESA410NE, ESA408NTC Owner’s Manual

...

User & Care Guide Guide d'utilisation et d'entretien Guía de uso y cuidado

Room Air Conditioner

Climatiseur individuel

HWR05XCM ESA405N ESA406N

Aire acondicionado

de uso doméstico

ESA408N ESA410N ESA412N

Design may vary by model number. La conłguraWion SeuW varier selon le

numéro de modèle.

This user manual is Wo be only use for elecWronic conWrol 5,000 BTU, 5,200 BTU 6,000 BTU, 8,000 BTU 10,000 BTU and 12,000 BTU Models. - Some models may have an addiWional leWWer afWer Whe model number.

Ce guide duWilisaWion doiW ñWre uWilisé sWricWemenW avec les modèles à commande élecWroniTue de 5,000bBTU, 5,200 BTU 6,000 BTU, 8,000 BTU, 10,000 BTU eW 12, 000 BTU. - Sur cerWains modèles, le numéro de modèle SeuW ñWre suivi dune leWWre.

°F/°C

MODE SPEED TIMER

FAN HIGH ON

MED OFF

ENERGY SAVE

LOW

SLEEP

COOL

DEHUM

AUTO COOL

TEMP/TIME

FILTER RESET

CLEAN FILTER

POWER

AUTO RESTART

El dise÷o Suede variar conforme al

número de modelo

EsWe manual del usuario es únicamenWe Sara uWilizar los conWroles elecWrónicos modelos 5,000 BTU, 5,200 BTU, 6,000BTU, 8,000 BTU, 10,000 BTU b yb12,000 BTU. Algunos de los modelos Sueden Wener una leW

ra adicional

desSués del número de modelo.

0010559941

ENGLISH

TABLE OF CONTENTS

SAFETY INFORMATION............................................................................................................. 2

Important Safety Precautions ................................................................................................ 2-3

Operational Safety & Warnings ..................................................................................................4

INSTALLATION REQUIREMENTS ............................................................................................. 5

Tools and Parts ............................................................................................................................5

Location Requirements ..............................................................................................................6

Electrical Requirements ......................................................................................................... 7-9

HOW TO INSTALL ....................................................................................................................10

Unpacking the Air Conditioner .................................................................................................10

Preparing the Air Conditioner ............................................................................................10-11

Preparing the Window ..............................................................................................................12

Completing the Installation ......................................................................................................13

USING YOUR AIR CONDITIONER ........................................................................................... 14

Starting the Air Conditioner ...............................................................................................14-18

Using the Remote Control ..................................................................................................18-19

Changing the Air Direction .......................................................................................................20

CARING FOR YOUR AIR CONDITIONER ................................................................................ 21

Cleaning the Air Filter ...............................................................................................................21

Cleaning the Front Panel ..........................................................................................................22

Customer Service .....................................................................................................................22

Normal Sounds of an Air Conditioner ......................................................................................23

TROUBLESHOOTING ..............................................................................................................24

LIMITED WARRANTY ...............................................................................................................25

PRODUCT REGISTRATION

Thank you for purchasing our Haier product. This easy-to-use manual will guide you in getting the best use of your product.

Model number

Remember to record the model and serial numbers. They are on a label on the side of your unit.

Staple your receipt to your manual. You will need it to obtain warranty service.

Serial number

Date of purchase

ENGLISH

IMPORTANT SAFETY PRECAUTIONS

WARNING

THE INFORMATION IN THIS USE & CARE GUIDE MUST BE

FOLLOWED TO MINIMIZE THE RISK OF PERSONAL INJURY, FIRE,

ELECTRIC SHOCK OR OTHER UNSAFE CONDITIONS.

THE INSTRUCTIONS IN THIS USE & CARE GUIDE ARE NOT MEANT

TO INCLUDE EVERY POSSIBLE CONDITION OR SITUATION THAT

MAY OCCUR. USE CAUTION AND CARE WHEN INSTALLING, OPERATING

AND CLEANING THE AIR CONDITIONER.

1. Use this air conditioner only for its intended application as described in this Use & Care Guide.

2. This air conditioner must be properly installed and use the correct wall outlet that matches with the air conditioner’s power supply cord in accordance with the Installation Section of this Use & Care Guide before it is operated.

3. Never unplug the air conditioner by pulling on the power supply cord. Always grip the plug firmly and pull straight out from the wall outlet.

4. Replace the power supply cord immediately if it becomes damaged in any way. A new power supply cord must be purchased from the air conditioner manufacturer and installed by a qualified technician. DO NOT use a power supply cord that is cracked, split, cut, or damaged anywhere along its length or either at the plug end or connector end.

5. Turn off the air conditioner and unplug it from the wall outlet before performing any cleaning or maintenance.

6. Do not store or use combustible or flammable materials or liquids on or near the air conditioner.

7. If the wall outlet configuration does not match the plug configuration on the air conditioner, the wall outlet must be changed by a qualified electrician.

PAGE 2 SAFETY INFORMATION

IMPORTANT SAFETY PRECAUTIONS

8. This air conditioner contains R410a refrigerant and requires certiﬁed technicians to use the proper equipment, tools and safety standards that are approved for this refrigerant. Use only equipment certiﬁed for R410a refrigerant. In addition, under federal law, all refrigerant must be properly removed from the air conditioner prior to its disposal. For responsible disposal of the product please contact your local municipality for additional recycling options in your area.

READ AND FOLLOW THE

SAFETY INSTRUCTIONS CAREFULLY.

ENGLISH

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION PAGE 3

ENGLISH

OPERATIONAL SAFETY & WARNINGS

1. This air conditioner contains no consumer serviceable parts. If you have problems or questions regarding the operation of your air conditioner always call Haier Customer Service: 1-877-337-3639.

2. Be sure that the air conditioner is properly and securely installed in the window according to the installation instructions included in this Use & Care Guide.

3. DO NOT drill any holes in the base or sides of the air conditioner.

4. DO NOT place ﬁngers or objects in the air discharge or air intake in the front of the air conditioner.

5. DO NOT operate the air conditioner with a protective cover on the outside section.

6. DO NOT block the air discharge or air intake areas on the front panel.

7. DO NOT block the side louvers on the outside of the air conditioner.

8. DO NOT place any objects either on the indoor or outdoor sections of the air conditioner.

9. Operate the air conditioner with the air ﬁlter installed.

10. Keep this Use & Care Guide, carton and packing material for future use

in removing, storing and reinstalling the air conditioner.

PAGE 4 SAFETY INFORMATION

TOOLS AND PARTS

Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED

ENGLISH

Phillips head screwdriver Scissors

Level Tape measure

Drill and 1/8” bit Pencil

PARTS SUPPLIED:

Check that all parts for your speciﬁc air conditioner are included in the parts package.

NOTE: If parts are missing, call Haier Customer Service: 1-877-337-3639.

IMAGE PART

Top channel

Foam seal

Side bracket

HWR05XCM ESA405N ESA406N

ESA408N ESA410N ESA412N

TEMP/TIME

Window lock

bracket

3/8" self-

tapping screws

1" wood screws

Side curtains

Side curtain

frames

ON/OFF

MODE

SPEED

TIMER

Remote control 1

INSTALLATION REQUIREMENTS PAGE 5

ENGLISH

IMPORTANT: evresbO all governing codes and ordinances. Check the location where the air

THE LOCATION SHOULD PROVIDE:

• A grounded electrical outlet within 6 ft. (183 cm) of where the power supply cord exits the air

•

NOTE: oD not use an extension cord, plug adapter, surge protector or multi-outlet adapter.

LOCATION REQUIREMENTS

conditioner will be installed. Make sure you have everything necessary for correct installation.

conditioner, for models: HWR05XCM ESA405N ESA406N ESA408N

A grounded electrical outlet within 4 ft. (122 cm) of where the power supply cord exits the air

conditioner, for models: ESA410N ESA412N

Free movement of air in the room to be cooled.

•

A large enough window opening for the air conditioner. (See Fig.2)

•

he air conditioner must not be installed in a through-the-wall sleeve or in a wall. It can only be

•

installed in a double-hung window.

NOTE:

The outside cabinet louvers and air discharge must not be obstructed by bushes, trees, etc. Air must be able to pass freely through the cabinet louvers. (See Fig.1)

Fig. 2

Fig. 1

CABINET LOUVERS

B-HEIGHT

A-WIDTH

AIR DISCHARGE

WINDOW INSTALLATION

Window opening measurements: (See Fig.2)

A. Width Min/Max

HWR05XCM ESA408N/ESA410NESA405N/ESA406N

22"-36" 24-1/2" - 36" 25" - 36-21/32" 26-1/8" - 37-25/32"

ESA412N

B. Height Min 13-3/8" 13-3/8" 14-9/16" 14-9/16"

PAGE 6 INSTALLATION REQUIREMENTS

ELECTRICAL REQUIREMENTS

WARNING

ELECTRICAL SAFETY and WARNINGS

1. OD NOT cut or remove the grounding prong on the attached power supply cord. Doing so may cause sparks or ﬁre, and voids all warranties. For safety purposes the air conditioner must be properly grounded.

2. To avoid a ﬁre hazard or possible electric shock, DO NOT use an adapter plug, extension cord, surge protectors, or multi-outlet adapters with the air conditioner.

3. The power supply cord is equipped with a 3-prong plug which mates with a standard 115 volt wall outlet to minimize the possibility of electrical shock from this air conditioner.

4. The power supply cord includes a leakage current detection interrupter device (LCDI). A RESET and TEST button are on the plug case. The device should be tested on a periodic basis by pressing the TEST button and then the RESET button while it is plugged into the wall outlet. If the TEST button does not trip or the RESET will not stay engaged, do not use the air conditioner and contact a qualiﬁed service technician.

ENGLISH

5. evaH the wall outlet and circuit inspected by a qualiﬁed electrician to ensure that the wall outlet is properly grounded.

6. fI there is a 2-prong wall outlet present and not a 3-prong wall outlet, it is the responsibility of the user to have it replaced with a properly grounded 3-prong outlet.

7. The air conditioner should always be plugged into a dedicated electrical outlet which has a voltage rating that matches the serial label on the side of the air conditioner.

8. The electrical ratings for your air conditioner are listed on the Model/Serial Number label. The Model/Serial Number label is located on the side of the air conditioner cabinet.

9. Speciﬁc electrical requirements are listed in the chart below. Follow the requirements for the type of plug on the power supply cord.

POWER SUPPLY CORD

Wiring Requirements

115-Volt (103.5 min. to 126.5 max.)

•

15-Amp time-delay grounded fuse or circuit breaker

•

Use on single outlet circuit only.

•

INSTALLATION REQUIREMENTS PAGE 7

ENGLISH

RESET

TEST

ELECTRICAL REQUIREMENTS cont.

REQUIRED GROUNDING METHOD (See Fig.3)

Fig. 3

This air conditioner must be grounded. This air conditioner is equipped with a power supply cord that has a 3 prong grounding plug. The power supply cord must be plugged into a mating, grounded 3 prong outlet, and grounded in accordance with all local codes and ordinances. If a mating outlet is not available, it is the customer’s responsibility to contact a qualiﬁed electrician and ensure that a properly grounded 3 prong outlet is installed.

POWER SUPPLY CORD (See Fig.4)

NOTE: Your air conditioner's plug may diﬀer slightly in appearance from the one shown.

A. Reset button B. Test button

Fig. 4

This room air conditioner is equipped with an

a leakage current detection interrupter (LCDI)

power supply cord required by UL. This power supply cord contains a current detection device. If the power supply cord is crushed, this device will detect current leakage and power will be disconnected from the air conditioner. If this power supply cord is damaged, it cannot be repaired and must be replaced with a cord from the product manufacturer. If the power supply cord is damaged call Haier Customer Service: 1-877-337-3639.

PAGE 8 INSTALLATION REQUIREMENTS

ELECTRICAL REQUIREMENTS cont.

WARNING

• Electrical shock hazard

• gulP into a mating, grounded 3 prong

outlet.

• oD not remove the ground prong from the power supply cord.

TO TEST YOUR POWER SUPPLY CORD:

ENGLISH

• oD not use a plug adapter, extension cord, surge protector, or multi-outlet adapter

• ruliaF e to follow these instructions can result in injury, ﬁre, or electrical shock.

1. gulP power supply cord into a mating, grounded 3 prong outlet.

(See Fig.5)

2. Press RESET (on some devices, a green light will turn on).

3. rP ess TEST (listen for click; Reset button will trip, and on some devices a green light will turn oﬀ).

4. rP ess and release RESET (listen for click; Reset button will latch, and on some devices, a green light will turn on). The power supply cord is ready for operation.

NOTE:

The RESET button must be pushed in completely for proper operation.

•

(See Fig.6)

The power supply cord must be replaced if it fails to trip when the test

•

button is pressed or fails to reset. DO NOT turn the air conditioner on or oﬀ by unplugging the power

•

supply cord from the the control panel or by using the remote control.

A damaged power supply cord must be replaced with a new power

•

supply cord obtained from the product manufacturer and installed by a qualiﬁed service professional. It cannot be purchased at a retail store and must not be repaired by the user.

outlet. Always turn the air conditioner on or oﬀ at

Fig. 5

Fig. 6

RESET

TEST

fI the power supply cord is damaged please call Haier Customer Service:

1-877-337-3639.

The power supply cord contains no user-serviceable parts.

•

• Opening the tamper-resistant case voids

all manufacturer warranties.

INSTALLATION REQUIREMENTS PAGE 9

ENGLISH

REMOVE PACKAGING MATERIALS

•

UNPACKING THE AIR CONDITIONER

WARNING

EXCESSIVE WEIGHT HAZARD

When moving or lifting the air conditioner, use two or more people.

Wear gloves when handling the air conditioner to protect against

possible sharp edges and metal ﬁns.

Remove packaging materials. Save the carton and the foam packaging for storing the unit when not in use.

NOTE:

•

There are NO internal packing materials inside the air conditioner to remove―Do Not open the cabinet.

Handle the air conditioner gently. Keep the air conditioner upright and level. Do not set the air conditioner on its side, front, back

or upside down. The air conditioner must be standing upright

for 2 hours prior to installation and operation.

PREPARING THE AIR CONDITIONER

INSTALL TOP CHANNEL

Front

7/16"

Screw

(actual size)

1. Place the top channel on the top of the air conditioner, lining up

the holes in the top channel with the holes in the top of the unit. Make sure the channel is facing forward as indicated by the illustrations.(See Fig.7&8)

To p Channel

Fig. 7

2. Using 7/16" self-tapping screws, attach the top channel to the top of the

air conditioner. (See Fig.8)

Use three (3) 7/16" self-tapping screws for models:

HWR05XCM ESA405N ESA406N

Use four (4) 7/16“ self-tapping screws for models:

ESA408N ESA410N ESA412N

PAGE 10 HOW TO INSTALL

Fig. 8

PREPARING THE AIR CONDITIONER cont.

INSTALL SIDE CURTAINS

NOTE: Attach side curtains to the air conditioner before placing the unit in the window.

1. Place the tabbed side of the side curtain in the track on the right-hand side of the air conditioner cabinet. (See Fig.9)

Fig. 9 Fig. 10

ENGLISH

TABBED SIDE OF SIDE CURTAIN

2. Slide the tabbed side of the side curtain down over all 3 tracks until the curtain is aligned with the top and bottom of the air conditioner cabinet. (See Fig.11)

3. Slide the side curtain frame over the top of the side curtain, then into the channel on the top of the air conditioner and into the track on the bottom of the air conditioner. (See Fig.12)

4. Slide the side curtain frame as close to the air conditioner cabinet as necessary to lock the side curtain to the frame. Gently press the frame until it clicks. (See Fig.10 & Fig.12)

5. Repeat above steps for the left-hand side curtain and frame. Make sure no gaps are left to ensu air does not escape into or out of the room.

LOCK EDGE SIDE OF SIDE CURTAIN

Fig. 11

Fig. 12

re that

CLICK

HOW TO INSTALL PAGE 11

ENGLISH

PREPARING THE WINDOW

1. Measure the width of the window opening.

(See Fig.13)

2. kraM the center line on the inside of the windowsill with a pencil.

WIDTH OF

(See Fig.14)

CENTER LINE

WINDOW OPENING

)LJ

WIDTH

)LJ

CENTER

NOTES AND WARNINGS:

BesureyourairconditionerdoesnotfalloutofthewindowopeningduringLQVWDOODWLRQ

Ũ

orremoval.

Do not block the air discharge or air intake areas on the front panel.

•

oD not block the louvers on the outside of the air conditioner.

•

Top Channel

Lower Window Sash

3. retneC the air conditioner in the window sill. Make sure to place the unit so that it is resting on the windowsill with a ¼" to ½" downward tilt towards the outside. Lower the window sash behind the top channel to hold the unit in place.

(See Fig.15)

)LJ

NOTE: The appearance of your model may diﬀer from the

one shown.

4. Loosen the screw located on the lower-right hand corner of the air conditioner.

5. edilS the side bracket over the screw. The side bracket should be resting on the window sill.

(See Fig.16)

6. Partially tighten the screw. Secure the unit before tightening completely.

7. esU 1/8" drill bit to drill a starter hole through the holes in the side bracket into the window sill.

8. gnisU two (2) 1" wood screws, attach the side bracket to the window sill.

9. Repeat for side bracket installation on the left-hand side of the air conditioner.

PAGE 12 HOW TO INSTALL

)LJ

COMPLETING THE INSTALLATION

ENGLISH

ATTACH SIDE CURTAINS TO WINDOW

1. lluP the right-hand curtain and frame out until it ﬁts ﬂush to the side of the window frame.

2. Use a 1/8” drill bit to drill a starter hole through the top hole in the side curtain and into the window sash.

3. Insert one (1) 1" wood screws through the top hole of the left hand curtain and into the window sash.

4. Repeat for the left-hand curtain.

5. Use a 1/8" drill bit to drill a starter hole into the window sill using the bottom hole in the side curtain as a guide.

6. Insert one (1) of the 1" wood screws through the bottom hole of the right-hand curtain and into the window sill.

7. Repeat for the left-hand curtain.

(See Fig.17)

(See Fig.18)

(See Fig.19)

FINAL INSTALLATION

1. Uncoil the included foam seal. (See Fig.20)

2. Insert the foam seal behind the top of the lower window sash and against the glass of the upper window sash.

Fig. 17

Fig. 18

3. ecalP the window lock bracket as shown in the diagram using a screwdriver. Use a 1/8" drill bit to drill a starter hole through the hole in the window lock bracket and into the upper window sash.

(See Fig.21)

4. Attach the window lock bracket to the upper window with one (1) 1" wood screw to secure the unit in place.

5. gulP unit into a grounded 3 prong outlet.

6. rP

ess RESET on the power supply cord.On some devices a

green light will come on. See “Electrical Requirements" for

full detail.

Fig. 19

Fig. 20

Fig. 21

HOW TO INSTALL PAGE 13

ENGLISH

STARTING THE AIR CONDITIONER

°F/°C

MODE

FILTER RESET

POWER

MODE SPEED TIMER

FAN HIGH ON

ENERGY SAVE

COOL

DEHUM

MED OFF

LOW

AUTO COOL

TEMP/TIME

FILTER RESET

CLEAN FILTER

POWER

AUTO RESTART

SLEEP

TIMER

SPEED

TEMPERATURE / TIME

CLEAN FILTER INDICATOR

Operating your air conditioner properly helps you to obtain the best possible results. This section explains how to operate this air conditioner.

IMPORTANT:

•

PAGE 14 USING YOUR AIR CONDITIONER

nehW you turn oﬀ the air conditioner , either at the control panel or with the remote control, wait at least 3 minutes before turning it back on. This prevents the compressor from overloading. This 3 minute delay also applies when switching from cool mode to fan and back. Note: There is a built in 3 minute delay. You may notice the compressor might not start right away. This was designed to protect the unit.

Do not operate your air conditioner in the Cool mode when the outside temperature is below 61°F (16° C). The inside evaporator coil will freeze up, and the air conditioner will not operate properly.

STARTING THE AIR CONDITIONER cont.

1. Carefully remove the clear plastic ﬁlm from the control panel.

2. rP ess POWER once to turn on the air conditioner. NOTE: nehW the air conditioner is ﬁrst plugged in, the LED display will show “88” for 3 seconds.

After the air conditioner is turned on for the ﬁrst time, the display will show the temperature 72 F and the fan is automatically set to Low speed and the Mode indicator will show ENERGY SAVE.

TE: To switch the temperature display between Fahrenheit (F) and Celsius(C), the air

conditioner must be plugged in, and turned ON. On the control panel on the front of the AC, press the UP and DOWN button at the same time and hold for 3 seconds. The change cannot be done using the remote control.

NOTE: Each time this Energy Star qualiﬁed air conditioner is turned on, it will operate in Energy Save mode per EPA requirements. You can select any other mode to satisfy your needs.

3. Select Mode. Refer to “Mode.”

ENGLISH

4. Select Speed. Refer to “Speed.”

5. Set Timer. Refer to “Temp/Time”

6. Reset the ﬁlter Check reminder. Refer to “Filter Reset ”

MODE

1. Press mode until you see the indicator light come on next to the desired setting.

2. Choose Fan, Cool Energy Save, or Dehum. FAN― Only the fan runs. Press SPEED to select High, Med or Low fan speed. The display shows

the current room temperature.

ENERGY SAVE― In this mode the fan runs only when cooling is needed. The fan will run for 3

minutes after the compressor shuts oﬀ. The fan then cycles on for 2 minutes at 10 minute intervals until the temperature in the room is above the set temperature. The compressor then turns back on.

COOL― Cools the room. Press SPEED to select High,Med , Low or Auto Cool fan speed. Press the

TEMP/TIME up or down arrow button to adjust the temperature. The fan will run continuously in cool mode.

DEHUM― iA sdin removing humidity from the room. This setting will NOT cool the room.

Temperature and fan speeds cannot be adjusted.

USING YOUR AIR CONDITIONER PAGE 15

+ 37 hidden pages