0010555512
6-7
8-12
8-12
13-20
15-20
1
1
2
4
4
5
5
8
14
14
21-22
22-23
24
Important:
Test power plug before each use:
1. Press ìreset ìbutton.
2 . Press ìtest ìbutton, unit should trip.
3. Press ìresetî button again for use .
Do not use if above test fail.
In the event this device trips , the cause of the malfunction is to
be corrected before further use of the device .
side vent
louvers
easy-access
filters
vent
controller
electronic
touch pad
You can run the fan only on not so hot days. The
fan can be set to run at 3 speeds (HIGH fan, MED
fan, LOW fan)as desired by you.
You have 3 levels of Fan Speed to set at your
desired comfort level. HIGH, MED and LOW .
24
The Fresh Air Vent allows the air conditioner to
recirculate inside air, draw fresh air into the room
and exhaust stale air to the outside .
12. Electrostatic Filter (not all models)
Being constructed of high efficiency purifying
substance, active carbon fabric, electrostatic fabric,
electrostatic active carbon net and other materials
it purifies the air effectively. Its wavy structure
increases the capability to filter dust and smoke
effectively. Due to the retention of the active carbon
it has a high purifying speed capable of
strong airflow.
Remote control and control panel operations
Having set the temperature you will set the function of the air conditioner.
Every time you press the MODE button, it will change between FAN , COOL, ENERGY
SAVER and DEHUM. (See Fig. # 3)
Once the function mode is decided you will have to set the fan speed.(See fig. #4)
Every time you press the SPEED button, fan speed will change between LOW,
HIGH,MED.
1) If you choose the COOL mode you can run the fan in one of the 3 speeds HIGH,
MED, LOW.
2) For cool days you may want to run the "F AN" function.
3 speeds (HIGH fan, MED fan, LOW fan)as desired by you.
4)Energy Saver : The unit runs the same as COOL setting in the ENERGY SAVER
mode. But the fan will be off 3 minutes after the compressor cycle off.
The fan can be set to run at
Fig. # 5
Adjusting the Air Flow Direction
Airflow can be adjusted by changing the direction of the air conditioner's louvers.
This can also increase the cooling efficiency of the air conditioner.
Adjusting Horizontal Air Flow
Direction
Adjusting the vertical louvers left and
right will change horizontal airflow.
Adjusting Horizontal Air Flow
Recommended orientation of louvers
Adjust louvers to face upwards when cooling to maximize cooling efficiency.
Adjusting Vertical Air Flow Direction
Adjusting the Horizontal vane up and down will
change vertical airflow. The vane can be adjusted
by nudging the back or up and down of the vane.
Adjusting Vertical Air Flow
Parts
Par ts Supplied
window seal
gasket
curtain
attachment
screws 13/32"
wood screws 31/32"
19/32" long
basepan angle
installation bracket
(left and right)
Model:
HWR18VC5, HWR24VC5, ESA3156,ESAX3186, ESA3245,ESA3185
screw and
locknut
Remote
control
2
head bolt and
locknut
ìCR2025ì battery
top rail
1/2
" long flat
left and right
curtains
side
Installing Unit into A Window
Window Opening Requirements
The air conditioner is designed to fit into double or single hung sash type windows. Each of the
units comes with an installation kit that provides adjustable mounting louvers, to fill the gaps
between the sides of the unit, and the window frame. The chart below reflects the dimensions of
the units with, and without installation kits. Measure your window opening width and compare
it to the chart below to ensure that it meets the minimum and maximum window width requirements.
B
C
D
2
11
"
5
3
18
"
5
3
18
"
5
5
42
"
16
1
30
"
8
21
"
18
32
9
"
26
16
13
24
"
32
Model
Dimension
A(inch)
B(inch)
C(inch)
D(inch) Max
D(inch) Min
Case High
Case Width
Case Depth
A
HWR18VC5, HWR24VC5, ESA3156,ESAX3186, ESA3245,ESA3185
HWR18VC5,HWR24VC5,ESA3156,ESAX3186,ESA3245,ESA3185
Unpack unit on floor next to installation
location.
Remove two front attachment screws.
Separate the outer case from the front
with a putty knife at the catch points
designated by the arrows.
Remove the two screws on top of the
outer case.
Using the basepan handle, slowly and
evenly pull chassis out from outer case.
Note: Cover putty knife blade with
masking tape to guard against damage
of the unit finish.
Caution: Never expose plastic
front or grille to extreme
temperatures.
ASSEMBLE
2
CURTAINS/TOP
RAIL
Inst all top rail with four screws.
Slide lef t-hand cur tain assembly
into lef t end of top and bottom
rails. Repeat for right-hand cur tain
assembly . Fasten cur tain ret ainer
strip s to sides of outer case with
six13/32" screws.
13/32"
PREPARE
3
WINDOW FOR
INSTALLATION
Inspect window track, sash, and sill
for it s ability to suppor t the weight of
air conditioner .
Measure wid th between window
moldings to ensure Inst ant Mount
will fit window frame. Inst ant Mount
models are designed for windows
wide (the detail see page 15)
Inst ant Mount kit supplied with unit
is designed for mounting in most
double-hung windows without
storm windows. For inst allation in
window frame with storm window ,
modify sill by adding wood strip s(not
included)
to
inner and outer sills. This
unit and eliminates inter ference
raises
of
storm window frame.
Storm window installation
If storm window frame does not allow
adequate clearance below sill (1/2"
required), remove storm window
frame or create clearance by adding a
wood strip (at least 1 1/2" wide) along
entire wid th of sill. Fasten wood strip
to sill with at least three countersunk
wood screws (not supplied with kit).
This provides a smooth sur face for
mounting air conditioner .
Min imum
1 1/2"
SI LL
I
N
D
O
O
R
St orm Wi ndo w
Fram e
W ood
Str i p
Min i mum
O
U
T
D
O
O
R
Mobile home window installation
Add wood strip (at least 1 1/2" wide)
along entire wid th of window sill.
Thickness of wood strip should match
height of front lip on window frame.
Fasten wood strip to sill with a
minimum of three countersunk wood
screws (not supplied with kit). This
provides a smooth sur face for
mounting air conditioner .
1/2"
Mus t be a mini mum
of 1/2" to cl ear
botto m rail on unit
1 1/ 2"
Minimum
I
N
D
O
O
R
Window
Frame
W ood
St rip
O
U
T
D
O
O
R
4
Top rail
INSTALL OUTER
CASE IN WINDOW
Place outer case in window. Lower
sash until it rests behind front flange
of top rail. Bottom rail must rest
behind window sill.
About
5∞
Expand both curtains to contact the
window frame. Install four wood
screws 31/32". Two in each upper right and
Bottom rail
Curtain assembly cut
away for clarity.
Use two wood screws 31/32" to fix the case to
windows sash. Install left & right installation bracket
and as shown in fig. Install bolt(2 1/2" long flat head
bolt and locknut) to the installation bracket and adjust
them to proper length ,then use 4 (19/32")screws to fix
the bracket on the case.
left of the curtains.
Install three wood screws 31/32" top mounting rail
screws.
NOTE: To make screws easier to
drive, drill a pilot hole into sash
through clearance hole in curtains.
INSTALL SASH BRACKET
5
& SEAL GASKET
Install sash bracket on top of indoor window sash
with one wood screw 31/32" to prevent raising of
window from the outside. Screw anchor directly into
side of window frame. For hard wood or metal window
frames, drill a pilot hole to start screw.
Important:Be careful not to drill pilot hole too deep.
Add a piece of tape to the drill bit as a depth gauge.
Also stay clear of glass. Be careful not to damage the
function of the window.
Cut window seal gasket to width of window. Stuff window
seal strip between outdoor window glass and top of
indoor sash. This will stop air leakage which reduces
efficiency.
6
Caution:
For security purpose, reinstall
screws at cabinet's sides, removed
in step one.
Remove the 2 shipping screws on the top of the air conditioner
that hold the chassis to the outer shell casing.
Always unplug your air conditioner before cleaning.
The air filter behind the inlet grille should be checked and cleaned at least
once every 2 weeks (or as necessary) to maintain optimal performance of
the air conditioner.
How to remove the air filter
1. The grille may be opened from the top for easy maintenance after installation.
2. Open the inlet grille by pulling off the exposed door on the top of the
unit(based on the installation).
3. Pull the tab slightly to release the filter . P ull the filter in the same direction
as the opening.
4. Clean the filter with warm, soapy water. The water should be below
40oC(104oF).
5. Rinse off and gently shake off excess water from the filter . L et it dry before
replacing it.
DO NOT use your air conditioner without the air filter in place.
To clean the front panels or the cabinet DO NOT use harsh
chemicals, abrasives, ammonia, chlorine, bleach, concentrated
detergents, solvents or metal scouring pads.
Always use a soft cloth dampened with water or mild soap
and water solution to wipe the front if the cabinet.
(See page 8)
(See page 17)
Loading...