Fully automatic washing machine
User's manual
This manual is for
BW1500W
Please read this manual carefully before using.
Retain it for future reference.
Contents
Names of the parts
Safety precautions
Installation and adjustment
Installation the water inlet hose
Preparation before washing
Put in the laundries
Add the detergent
Use the operation knobs and buttons
Close the top lid
Finish washing
Disposal after washing
Trouble-shooting Answer to question
Packing list Specification
*
Names of the parts
Top lid, I
Top lid, II
Detergent box
Location of lint filter
Control panel seat
Level meter
Inner tub
Control panel film
Pulsator
Cabinet
Lower cabinet
Water absorption cushion
Power cord
Drain hose
Back cover
Fixing foot
(three)
Adjustable foot
Water inlet valve
Meaning and description of the symbols
Contents marked with that symbol are related
Warning sign
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damageof the machine or injure the
personal safety of the user.
Drain hose hanging hole
Handle
Forbidding sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Safety precautions
Please insert the power cord into
special receptacle with rated voltage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be inserted and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
Earth
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp place like
the bathroom. Never wash it with water.
The ventilation
holes at the bottom
Soft object
Do not use water hotter than 50 C .
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the
plugging into the receptacle is loose, do not use the plug any more.
Do not wash water-proof laundries like the raincoat,
bike covers etc. to avoid abnormal vibrations in spinning.
Safety precautions
Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.
Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine
The handicapped or children without care shall not
use the machine.
Do not decompose, repair or alter the machine
by yourself.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Benzene
Keep the machine away from direct sunlight and
heat source like the heater.
The lint filter shall be kept in good condition, and
installed to proper position. If the lint filter is lost
or damaged, please contact the local after-sales
service department of our company.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Install the bottom plate
After opening the package, please lean the
washing machine gently down on soft items
(like towel cloth, blanket, etc.). Install the
bottom plate to the bottom of the machine
with eight screws by a cross screwdriver,
then lift the machine up gently. See to the
figure:
Install the lint filter
After opening the package, please take out the
lint filter from the document bag and install it
into the Filter frame of the inner tub. See to the right figure.
Adjust the installation position
The largest allowable slope of the shank base of the machine is 2 .
The slanting or rough ground will result in unstable running or
stoppage of the machine. Please adjust it with following methods:
Bottom plate
Filter frame
Screw
Back
Front
Soft items
Lint filter
Confirm it's horizontal:
If the bulb of the level meter at the balance display
position is inside the standard circle, it indicates that
the machine is horizontal. Otherwise you need to
adjust the adjustable leg of the machine.
Adjust the adjustable leg:
1.To twist the adjustable leg, please first lift up the
leg side slightly, loosen the adjustable nut, and
then twist the leg.
2.After adjustment, fasten the nut.
Loosen
High
Air bubble
Suitable Not suitable
Standard circle
Adjustable nut
Fasten
Adjustable leg
Low
How to change the direction of the drain hose
1.Lean the machine down gently with the front
surface facing the ground.
Back
Front
Soft item
2.Pull out the drain hose from the groove at the left side.
Use groove at
this side after
direction changing
Usage of the drain hose
The drain hose shall drain smoothly
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.
2.Do not ramp or press the drain hose.
3.Extend the drain hose from the left side. Push the
drain hose into the groove with hands.
4.Install the bottom plate (as per indicated
before), then lift the machine up gently.
Page 4
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
If the extra hose is too long, cut it
either at A or at B point.
Install the water inlet hose
Install the water inlet pipe
Water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10mm.
The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2. Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose
jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four
screws and take out the bush inside the jointer. See to Figure 3.
Water inlet hose jointer
Slider
Screw
Lock level
Water inlet hose
3. Fasten the four screws of the water inlet hose jointer evenly. See to Figure 4.
4. Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Remark: .Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
Figure 4
Screw knife
Figure 1
Screw nut
Figure 5
Nameplate
Figure 2
About 4mm after twisting
About above 2mm after twisting
Bushing
Figure 3
Figure 6
Connection between the water inlet hose and the washing machine
1 Do not take off the water absorption cushion. Please check
if the cushion is dropped or damaged each time before using.
If it happens so, please duly contact our after-sale service
department.
2 Set the nut of the water inlet hose on the water inlet valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's fastened well.
Water inlet valve jointer
Water inlet
hose nut
Water absorption cushion.
Connection between the water inlet hose jointer and the water inlet hose
1. Push down the slider. Plug the water inlet hose into the jointer.
2. Hang the lock lever onto the jointer. Release
the slider till a click sound is heard.
Locking level
The water inlet
hose jointer
Slider
Check the connection between the water inlet hose jointer and the
water faucet
1.Swing the hose gently to check if it is fastened stably.
2.After installation, open the faucet to check if it leaks water.
3.Do not bend the hose by force.
4.Each time before using, please check if the connection
between the water inlet hose jointer and the water faucet,
and the installation of the water inlet hoseis firm, so as
to avoid dropping owing to improper installation.
Dismount the water inlet hose
1. Close the water faucet.
2 .Press the lock lever and push down the slider. Then pull off the
water inlet hose. If the machine is used more than once every
week, the water inlet hose jointer can remain on the faucet to
avoid damaging the fastening screws.
Lock level
Slider
7
1 Preparation before washing
Preparation before washing
1.Connect the water inlet hose. Open
the water faucet.
2.Confirm that the washing machine is
earthed reliably. Then insert the
power plug into the receptacle. The
earth terminal shall not link to gas
pipeline and faucet water pipeline.
3.Put down the drain hose.
Pay attention to followings before washing the laundries
Check if
the laundries
has special
requirement
on washing
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the long
strips; fasten
the buttons;
close zippers.
The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
2 Put in the laundries
3 Add the detergent
Inlet of the concentrated synthetic detergent
The capacity of washing and spinning of the machine
refer to the largest weight of the standard laundries
under dry condition that can be washed or spinning in
one time.
The thickness, size, type of the cloth will influence the
actual washing capacity. It is suitable for one time
washing to put in reasonable amount of laundries
and the laundries can be turned round in washing.
Do not select above 8 water level for laundries small
than 2.0kg, so as to avoid splashing of water.
First turn the detergent box down before adding detergent.
Add the concentrated composite washing powder into the box
directly as indicated in the left figure.
See to following table for water level, water quantity and
selection of powder.
How to use the whitener
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before use.
How to use the washing powder
Directly dissolved in the machine (not applicable for fuzzy
program and reserve wash)
1.Fill small quantity of water.
2.Add the powder. Run for 30 seconds to dissolve it completely.
3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 and a container.
2.Add the powder while stirring to fully dissolve it.
In selecting the super quick program, it is suggested to adopt
liquid detergent instead of washing powder to guarantee the
washing effect.
Put in the proper quantities detergent according to the water
level and the laundries quantities.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage
maybe caked. Please pay attention to cleaning the
detergent box in time.
4 Use the operation knobs and buttons
Description of the function of the knobs and buttons
Mode and meaning of the VFD indicator
The frame of indicator is not lighted.
The frame of the indicator is flashing : indicate the running program.
The frame of the indicator is on : indicate the program about to run,
or indicate the selected mode
The frame of the indicator is flashing rapidly: indicate abnormal condition.
Digital tube
During working , it displays the remained
reserve time (minute).
During reserve, it displays the remained
reserve time (hour)
In case of trouble, it displays the abnormal
symbol(see to page 16)
RESERVE button
RESERVE
WATER
LEVEL
During operation, the digital tube will display
the remained time before finishing in minute.
Push the reserve button. The digital tube will
display the reserve time for finishing of washing
in hour. The indicator will flash to indicate that
the reserve function is working.
WATER LEVEL button
You need to select the water level by yourself.
If you put in wet laundries, you need to select
suitable water level manually. Refer to
water level water quantity and
selection of powder in page 9.
In selecting the quick wash program, the water level is set to 2
automatically. When the 2 is reached, it will do washing while
filling water. When 4 is reached, it will perform normal washing.
Due to the variable cloth and humidity, the set water level may be
different from the actual water level. Sometimes it may perform
water adding.
During washing, push the water level knob to add water.
PROCESS button
one or more one programs among
soak wash rinse spin
can be selected.
PROGRAM
PROCESS
START
PAUSE
POWER ON/OFF button
Push the "On/Off" button to switch on the power.
When the power is on, push it again to switch off
the power.
After the power is switched on , if the washing machine is idle
for 10 minutes, it will switch off the power automatically.
POWER
ON/OFF
START/PAUSE button
After the power is switched on, push it to start the machine
During working, push it to pause working.
During pause, push it to resume working.
PROGRAM button
The following four programs are available.
Standard Common washing
Programs
Jeans Washing large , thicker ,
or heavily soiled laundries
Gentle Washing woolen textile
or underwear
Quick 15-minute quick wash for the
laundries with under 3 kg
b Steps of using the operation buttons and description of each step.
BW1500W
RESERVE
WATER
LEVEL
START
PAUSE
PROCESS
PROGRAM
Push the POWER ON/OFF button to switch on the power.
POWER
ON/OFF
POWER
ON/OFF
PROGRAM
Push the PROGRAM button to select the suitable automatic program.
After switching on the power, the machine will set to standard program automatically. To select other program, push the
PROGRAM button till the corresponding indicator is on. Refer to the PROGRAM button in Page 11.
Page 11
For an example: select quick wash for the quick washing of the laundries with light dirt.
Push PROCESS button to select suitable procedure
PROCESS
After switching on the power, the machine will set to WASH-RINSE-SPIN program automatically. That is the most
common program. To select other program, push the PROCESS button to select one or more procedures
among SOAK WASH RINSE SPIN .
Refer to the METHOD for the selection.PROCESS SELECTION
Page 13
Attention
Even there's no water in the tub, a certain period
is required before spin starting.
Do not use the SOAK program for the woolen
textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
4 Selection method of the procedure programs
Times of pushing
the PROCESS
button
Selected procedure
program
Applicable procedure
Contents (the lighted indicators
indicate the programs about to run)
Wash, rinse, spin
(standard program)
Wash (the washing liquid
remains in the tub)
Wash (the rinsing liquid
remains in the tub)
Rinse, spin
Spin
(spin after drain)
soak wash, rinse, spin
If you push the process button for 6 times, it will resume the initial mode, and it will circulate in that way.
The soak program can be used as fitting of the standard/jeans automatic programs.
It will do soaking with intermittent stirring of pulsator.
After the washing machine starts working, you can only make selection during wash , and cannot make selection
during other procedures.
Push the RESERVE button to select the suitable reserve program
When the power is switch on, the RESERVE program is disabled automatically. If you need to finish the washing in reserved time,
please push the reserve button to select suitable program. Refer to the RESERVE button in Page 10.
When the common laundries need
washing , rinsing and spinning
Repeat using the washing liquid
Repeat using the rinsing liquid
When the laundries need rinsing and
spinning after hand washing
When the laundries only need spinning
after hand washing(first spin then drain)
If the laundries are very dirty, or the sleeve
and collar are dirty, first soak then wash
Page10
Soak
Soak
Soak
Soak
Soak
Soak
Wash
Wash
Wash
Wash
Wash
Wash
RESERVE
Minute Remained
Rinse Spin
Rinse Spin
Rinse Spin
Rinse Spin
Rinse Spin
Rinse Spin
Confirm the reserve program
When the reserve program is started, the digital tube will display
the finishing time of the reserve washing.
To change the running program or cancel reserve, you shall
switch off the power and make new selection.
The water inlet pressure and water level can influence the finishing time of washing.
16 hours later, finish wash
The washing will finish about 18 hours later.
Hour reserved
Push the START/PAUSE button
START
PAUSE
5 close the lid 6 finish washing
Excluding during soak, wash, filling water procerdure,If you open
the top lid, the machine will stop working and alarm before spinning.
When the washing is finished, the power
will be switched off automatically.
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:
1. Pull it up to dismantle.
2. Push it down to install.
3. Clean the filter screen after washing.
Dismantle
Install
Clean
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water inlet.
Please clean it with brush every two months.
Clean the detergent box, then set it on
the control panel seat
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
l
o
inner
Petr
h
T
Alcohol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (about 1 hour),
then close the top lid.
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are
not breakdowns sometimes. Please confirm again before sending it to repair. If there are real
breakdowns, please come to the special maintenance department or after-sale service department of
our company. Do not repair it by yourself.
Phenomenan The reason How to settle
After the reserve is started, it rings and the
digital tube displays E0
The draining does not work ,or the speed of
draining is too slow. The digital tube displays
E1 and it rings.
It stops running during spin .the digital
tube displays E2 and it rings.
The safety switch acts. The spinning
can not work (after twice revising)
The digital tube shows E3 and it rings.
The top lid is not closed.
*
Is the drain hose put down?
*
Is the drain hose blocked by
*
foreign material?
The top lid is not closed.
*
Are the laundries put slantingly? Re-order the laundries. Close the top lid.
*
Is the machine slanting?
*
Close the top lid.
*
Put down the drain hose.
*
Open and close the top lid once.
Clean the foreign material .
*
Open and close the top lid once.
Close the top lid.
*
*
Level the machine in right position.
*
Open and close the top lid once.
It does not do water inlet or the speed
is slow ( the water level is not reached
after 40 minutes). The digital tube
displays E4 and it rings.
the machine does
not act . (The
indicators are off.)
There's abnormal sound inside
the machine.
The water faucet leaks.
No wash
No spin
Is the water faucet open or is there water
*
supply failure?
Is the water inlet valve blocked.
*
Is there power failure?
*
Is the power plug loose?
*
If water level reach the appoint level?
*
Is the power plug loose?
*
Is the top lid is not closed.?
*
Are the laundries put slantingly?
*
Is the machine slanting?
*
Is there metal material inside the
*
washing machine?
Are the laundries slanting in spinning?
*
Is the jointer screw of the water inlet
*
hose loose or twisted awry?
Common phenomena
Phenomena Explanation
The spinning is intermittent when it starts.
Pause during washing
Push the PROSESS button to select SPIN, but it
doesn't act.
The pulsator pauses during waterfilling in washing and rinsing.
There may be some water flowing out of the drain
hose in the first use of the machine.
Open the water faucet.
*
Open and close the top lid once.
Clean the water inlet valve .
*
Open and close the top lid once.
Use it when the power is on.
*
Insert the power plug tightly.
*
Affusion to appoint level.
*
Insert the power plug tightly.
*
Close the top lid
*
Re-order the laundries. Close the top lid.
*
Level the machine properly.
*
Fasten the fastener or zip up the zip.
*
Re-order the laundries. Close the top lid.
*
Fasten the jointer screw properly.
*
It is to balance the laundries to avoid slanting.
Supplemental water filled after fabric sensor
has checked fabric(about 48 seconds).
The program is setting the drain time. A certain
period is needed before it starts spinning.
It is to avoid splashing during water filling.
It is the water remained in the machine during the
ex-factory performance inspection.
Packing list
Name
User's manual
Components of the
water inlet hose
Lint filter
Bottom plate
Tapping screws
Between the upper cushion of
the washing machine package
and the upper seal of the
package carton
Quantity
One
One
One
One
Eight
Automatic washing
machine
Specification
Water level/Water quantity (about)
Injection pressure
Rated washing / spinning capacity(kg)
1/29L 2/35L 3/41L 4/47L 5/53L 6/59L
7/65L 8/71L 9/77L 10/83L 11/89L 12/96L
One
0.03MPa-0.78MPa
12.0kg
Loading...