Haier BC100GS User Manual 2

Beverage Center

Centre de boisson

Centro de la bebida

User Manual

Guide de l'Utilisateur

Manual del Usuario Modelo

BC100GS

English

IMPORTANT SAFEGUARDS

When using this applaince, always exercise basic safety precautions, including the following:

1) Read all of the instructions before using this appliance.

2) Use this appliance only for its intended purposes as described in this use and care guide.

3) This appliance must be properly installed in accordance with the installation instruction before it is used. See grounding instructions in the installation section.

4) Never unplug your beverage center by pulling on the power cord. Always grasp the plug firmly and pull straight out from the outlet.

5) Unplug your beverage center before cleaning or before making any repairs. Note: If for any reason this product requires service, we strongly recommend that a certified technician performs the service.

6) Repair or replace immediately, all electric power cords that have becomefrasyed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length, the plug or the connector end.

7) This appliance is designed built-in use only in an enclosed cabinet.

8) If your old beverage center is not being used, we recommend that you remove the door and leave the shelves in place. This will reduce possibility of danger to children.

9) Do not operate your beverage center in the presence of explosive fumes.

10) Do not store foods in beverage center as interior temperature may not

be cool enough to prevent spoilage or may cause bacteria growth.

11) Cabinet edges along stamp/cut-out areas may be sharp. Please avoid

placing hands, ﬁngers, or other appendages near these areas.

12) This appliance is not intended for use by young children or inﬁrm

persons without supervision. Young children should be supervised to ensure they do not play with the appliance.

NOTE: Ambient operating temperature is between 55˚-90˚F.

SAVE THESE INSTRUCTIONS

DANGER

Risk of child entrapment. Before you throw away your old

beverage center, take off the doors. Leave the shelves in

place so that children may not easily climb inside.

English

TABLE OF CONTENTS

PAGE

IMPORTANT SAFEGUARDS ....................................................................1

PARTS AND FEATURES ...........................................................................3

INSTALLING YOUR BEVERAGE CENTER .............................................4-7

Unpacking your Beverage Center ................................................................4

Leveling your Beverage Center ....................................................................4

Installation Limitations .................................................................................4

Unit Dimensions .........................................................................................5

Electrical Requirements ...............................................................................5

Use of Extension Cords ...............................................................................5

Anti-tip Bracket Installation ..........................................................................6

Door Reversal ......................................................................................... 7-8

BEVERAGE CENTER FEATURES AND USE .........................................9-10

Initial Set up ..............................................................................................9

Temperature Adjustment ..............................................................................9

Sabbath Mode ..........................................................................................9

Alarm System ............................................................................................9

Capacity ...................................................................................................9

Shelving ..................................................................................................10

˚F/˚C Conversion .....................................................................................10

Interior Light ............................................................................................10

Power Button ...........................................................................................10

Normal Operating Sounds ........................................................................10

PROPER BEVERAGE CENTER CARE AND CLEANING ..........................11

Cleaning and Maintenance .......................................................................11

Power interruptions...................................................................................11

Vacation & Moving care ...........................................................................12

TROUBLESHOOTING ............................................................................12

WARRANTY ..........................................................................................13

Thank you for using our product. This easy-to-use manual will guide you in getting the best use of your

Model Number

beverage center.

Remember to record the model and

Serial Number

serial number. They are on a label in back of the beverage center.

Date of Purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

English

Parts And Features

3 4 5 6

9 8 7

1. LED Temperature Dispay

2. Temperature Adjustment (up/down)

3. Temperature Set Button

4. °C and °F Conversion

5. Interior Light Button

6. Power Button

7. Door Handle

8. Glass Door

9. Light Switch

10. Front Cover (Toe Kick)

11. Adjustable Leveling Leg

12. Bottom Rack

13. Fold Away Shelf

14. Glass Shelf

English

Installing Your Beverage Center

Unpacking Your Beverage Center

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the beverage center accessories inside and outside.

2. Inspect and remove any remains of packing, tape or printed materials before

powering on the beverage center.

Leveling Your Beverage Center

• Your beverage center has four leveling legs whch are located in the front and rear

corners. After properly placing your beverage center in its finals position, you can level it.

• Leveling legs can be adjusted by turning them clockwise to raise your beverage

center or by turning them counterclockwise to lower your beverage center. The beverage center door will close easier when the leveling legs are extended.

Note: If your beverage center has been titlted for any reason, wait 24 hours before

plugging it in.

Install Limitations

• Do not install your beverage center in any location not properly insulated or

heated e.g. garage etc. Your beverage center was not designed to operate in

temperature settings below 55˚ Fahrenheit.

• Select a suitable location for the beverage center on a hard, even surface away

from direct sunlight or heat source e.g. radiotors, baseboard heaters, cooking appliances etc. Any floor unevenness should be corrected with the leveling legs located on the front and rear botto m corners of the beverage center.

• Built-in beverage center need to be ventilated from the front. This feature allows

the unit to be built-in in an enclosed area. The bottom front grill should be clear of

all obstructions. This is absolutely necessary for the air to circulate and for the unit

to operate efficiently. The dimensions for installation are as follows (WxDxH). Note: Remove the upper hinge cover before built-in the beverage center.

English

25-1/2”

34-9/16”

Unit Dimensions

Model W D H

BC100GS 23-7/8" 23-3/4" 34-9/16"

Opening Dimensions

Model W D H

BC100GS 24" 24" 35"

23-3/4”

34-9/16”

25-1/2”

Electrical Requirement

• Make sure there is a suitable power outlet (115 volts, 15 amps outlet) with proper

grounding to power the beverage center.

• Avoid the use of three plug adapters or cutting off the third grounding prong in

order to accommodate a two prong outlet. This is a dangerous practice since it provides no effective grounding for the beverage center and may result in shock hazard.

Use of Extension Cords

• Avoid the use of an extension cord because of potential safety hazards under certain conditions. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot outlet that will

accept the plug. The marked rating of the extension cord must be equal to or greater than the electrical rating of the appliance.

English

Anti-tip bracket Installation

1. Take off upper hinge cover with upwards motion. Refer to illustrations below:

2. Take the anti-tip bracket and screws from the accessory bag. Tighten the anti-tip

bracket on the top of the product with screws as follows in the illustration. Note: Follow instructions properly or you may do damage to product.

3. Pull glass door open and attach the anti-tip bracket to counter by screw as seen

below. Adjustment of the leveling legs under the unit may be necessary for a proper fit in the cabinet opening. Start with the rear legs (if necessary) before you slide the

unit fully into the opening –rise or lower the rear legs to make the unit fit properly. Then carefully slide the unit into opening as not to damage accidently cabinetry or

the floor. Then perform the same adjustments to the front leveling legs to bring the front of unit to the proper level to install the anti-tip bracket and fit evenly under the

counter.

4. Another set of anti-tip brackets for side installation is provided as option when

the counter top is granite and hard to fix by screw. This set of brackets include one bracket and four screws for installation on left side if the cabinet when the door is

left-open or on the right side of the cabinet when the door is right-open. Below draft

illustrates the installation procedure.

English

Door Reversal

Left Door

Right Door

1. Upper hinge hole's cover

2. Hinge cover's plug and screw

3. Upper hinge's cover

4. Upper hinge's screw

5. Upper hinge

6. Front cover (toe kick)

7. Front cover's screw

8. Lower hinge's screw

9. Lower right hinge

10. Door stop spacer

11. Door stop spacer

12. Upper door hole spacer

13. Glass door

14. Door closer

15. Screw

16. Magnetic switch's screw

17. Magnetic switch

18. Lower left hinge (spare part)

19. Screw hole cap

Steps to Door Reversal

1. Remove lower toe kick (Front cover)

2. Remove plastic plug in the center if hinge cover (#3)

3. Remove screw from center of hinge cover (#2)

4. Remove hinge cover (#3)

5. Remove Square cover on left (#1)

6. Loosen and remove all 3 screws from upper door hinge (#4 and #5)

NOTE: Hold door while loosing and removing upper hinge to prevent fall and Damaging door as well as bodily injury

7. Lift door and lay door flat on the door

8. Loosen and remove the screws that hold the plastic door closer attached on

the door in place (#14 and #15)

9. Remove upper right hole plastic door spacer (#12)

10. Remove the small screw hole cap in place (#19)

11. Loosen and remove door magnet switch from bottom center of door (#16 and

#17) and reattach it to the top center of door.

12. Loosen and remove the 4 screws that hold the bottom right door hinge in Place

13. Remove bottom right door hinge

14. Loosen and remove the screw that hold the plastic door closer attached to the

bottom right door hinge (#10 and #11)

15. Attach and tighten plastic door closer removed in step 13 to the bottom left

door hinge provided in the accessory bag inside unit

16. Attach and tighten the bottom left door hinge to the unit with the screws

removed in step 8

17. Take door so handle is now on the right side as it is placed in front of you

and lay flat on floor

18. Insert plastic door spacer removed in step 9 into top left hole of door

19. Attach the plastic door closer to the door removed in step 8

20. Align the bottom left hole on the door with the pin on the bottom left door hinge

21. Slide into place gently

22. Take upper door hinge removed in step 6

23. Align pin of upper door hinge with hole on the upper left if door

24. Take the 3 screws removes step 6 and attach them to the screw holes on the

unit and tighten Note: Do not fully tighten yet

25. Make sure top of door is level with top of cabinet

26. Once level, fully tighten screws that hold upper door hinge in place

27. Replace upper hinge cover removed in step 4

28. Tighten hinge cover to unit with screw removed in step 3

29. Replace screw cover plug removed in step 2

30. Replace square cover removed in step 5 to top cover right screw holes

31. Replace the small screw hole cap removes in step 10

32. Attach and tighten toe kick (Front cover) to the unit with the screws removed in

step 1

English

Beverage Center Features and Use

Initial Setup

Once you have plugged the unit into an electrical outlet, let the unit run for at least 30 minutes to acclimate itself before making any adjustments. The LED display will show the current internal temperature.

Temperature Adjustments:

• The beverage center can be set to any temperature between 39˚ and 62˚F to

accommodate your storage requirements. To set the temperature hold the "Set" button for about 3 seconds. You will notice the temperature display blink.

Fig.#1

Sabbath Mode

• Press and hold "^" and "v" at the same time for 3 seconds, buzzer will ring

once, display panel will flash 5 times and stop. This indicates that the unit has entered Sabbath mode. In this mode, normal cooling operations still take place (compressor, magnetic valve, fan) but all luminous equipment including display panel and LED bulb will shut off no matter if the door is opening or closing. Press and hold "^" and "v" at the same time for 3 seconds, after display panel flahses 5 times, you cna exit from Sabbath mode.

Alarm System

Door Ajar Alarm- If the door of the unit is kept open for long time and affect temperature so much , the system will give an alarm, if you want to stop it, press "SET" button.

Capacity

The capacity of beverage center is 150 cans. The quantity may vary if the type

or the size of the beverage center & can change.

English

Shelving

• The shelves are designed for appearance and easy cleaning.

• There are 3 glass shelves for easy storage and removal of your beverage.

• The middle glass shelf is foldable, has three variable shapes to accommodate different sizes of beverage bottles. Below chart illustrates the recommended

storage ways.

“°F/°C” Conversion

Press and hold “°F/°C” for 3 seconds, the displayed temperature in Fahrenheit degree and °F character will convent to temperature in Celsius degree and “°C” character. Press and hold “°F/°C” for 3 seconds again, the temperature in Celsius degree and “°C” character will convert to temperature in Fahrenheit degree and “°F” character.

Interior Light

• To complement the look of your collection, a soft light has been built into the

beverage center. Simply push the "Light" button and the light comes on, push again for off. For maximum energy efficiency, leave light off when not viewing your collection.

• When door is open the light will go on. Upon closing the door, the light will go

off.

Power Button

• You can shut the power of the beverage center when you dont ned it to work

by pressing the "Power" button for 3 seconds. It will shut off the compressor, electromagnetism valve and the display panel. It can also be turned on again by pressing the "Power" button quickly. The light inside the beverage center will turn on if you open the door when the power shutting off in order to access the conveniently.

Normal Operating Sounds You May Hear

• Boiling water, gurgling sounds or slight vibrations that are the result of the

refrigerant circulating through the colling coils.

• The thermostat control will click when it cycles on and off.

English

Proper Beverage Center Care and Cleaning

Cleaning and Maintenance

WARNING: To avoid electric shock, always unplug your

Beverage Center before cleaning. Ignoring this warning may result in death or injury.

CAUTION: Before using cleaning products, always read and

follow manufacturer’s instructions and warnings to avoid personal injury or product damage.

General: • Prepare a cleaning solution of 3-4 tablespoons of baking soda

mixed with warm water. Use sponge or soft cloth, dampened with the cleaning solution, to wipe down your beverage center.

• Rinse with clean warm water and dry with a soft cloth.

• Do not use harsh chemicals, abrasives, ammonia, chlorine

bleach, concentrated detergents, solvents or metal scouring

pads. Some of these chemicals may dissolve, damage and/or

discolor your beverage center.

Door Gaskets: Clean door gaskets every three months according to general

instructions. Gaskets must be kept clean and pliable to assure a proper seal

• Petroleum jelly applied lightly on the hinge side of gaskets will

keep the gasket pliable and ensure a good seal.

Power Interruptions

• Occasionally there may be power interruptions due to thunderstorms or other causes. Remove the power cord from AC outlet when a power outage occurs. When power has been restored, replug power cord to AC outlet.

Vacation and Moving Care

• For long vacations or absences, empty food from beverage center and clean the beverage center and door gaskets according to "General Cleaning" section. Leave doors open, so air can circulate inside.

• When moving always move the beverage center vertically. Do not move with the unit lying down, as possible damage to the sealed system could occur.

Note: After moving, wait for 24 hours before plugging in the beverage center.

Troubleshooting

Beverage Center does not operate:

• Check if beverage center is plugged in.

• Check if there is power at the AC outlet, by checking the circuit breaker.

Food temperature appears too warm:

• Frequent door openings.

• Allow time for recently added product to reach desired temperature.

• Check gaskets for proper seal.

• Clean front cover.

• Adjust temperature control to colder setting.

Beverage Center is too cold:

• If temperature control setting is too cold, adjust to a warmer setting.

Beverage Center cellar runs too frequently:

• This may be normal to maintain constant temperature during high temperature

and humid days.

• Doors may have been opened frequently or for an extended period of time.

• Clean front cover.

• Check gasket for proper seal.

• Check to see if doors are completely closed.

Moisture build up on interior or exterior of the beverage center:

• This is normal during high humidity periods.

• Prolonged or frequent door openings.

• Check door gaskets for proper seal.

English

Beverage Center door does not shut properly:

• Level the beverage center .

• Check for blockages, e.g. beverages.

+ 29 hidden pages