Haier AS12SB1HRA, 1U09QE6ERA User Manual [nl]

SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL

Contents

AS09SH1ERA/1U09EH1ERA AS12SH1ERA/1U12EH1ERA

AS09SB1HRA/1U09QE6ERA AS12SB1HRA/1U12QE6ERA

PARTSAND FUNCTIONS

OPERATION

CAUTIONS

TROUBLE SHOOTING

Contenido

PARTES Y FUNCIONES

FUNCIONAMIENTO

PRECAUCIONES RESOLUCIÓN DE PROBLEMAS

Indice

PARTI E FUNZIONI

FUNZIONAMENTO

AVVERTENZE

RISOLUZIONE DEI PROBLEMI

18 19

Table des matières

ÉLÉMENTS ET FONCTIONS

UTILISATION

MISES EN GARDE DÉPANNAGE

Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

0010564687

Parts and Functions

Indoor Unit

Inlet

Inlet grille

Outlet

Negative Anion

generator

Horizontal flap

(adjust up and down air flow

Don’t adjust it manually)

(inside)

Intelligent eye

Please be subject to the actual produce purchased, the above picture is just from

your reference.

Display board

Signal receiver hole

iFP display

HEALTH display

(If the unit which you purchased has healthy

function,follow it. If not,please ignore.)

TIMER OFF display

TIMER ON display SLEEP display

temp display

Temp display include two displaying types.

Air Purifying Filter

(inside)

Vertical blade

(adjust left and

right air flow)

One is ambient temp displaying ,the other is set temp displaying. The displaying temp can be changed between ambient temp and set temp by some special operation.

SMART display

COOL display

DRY display

HEAT display

Emergency

Switch

Display board

Outdoor Unit

OUTLET

INLET

Remote controller

Outer side of the controller

SMART COOL HEAT

FAN DRY CTD

POWER SOFT

ECO

iFP

SMART ON/OFF

COOL

HEAT

DRY

ECONOMY FAN SPEED

iFP

1.iFP button

Induce the movement of the human body,so as to control the airflow / energy saving functioning.

2.ECONOMY button

Used to set ECONOMY operation.

3.DRY button

Used to set DRY operation.

SET TEMP.

AUTO AUTO

FAN SPEED

TIMER ON OFF

AM PM

ROOM TEMP.

AUTO

EVADE

CONNECTING PIPING

AND ELECTRICAL WIRING

DRAIN HOSE

4.HEAT button

Used to set HEAT operation.

(Cooling only unit do not have displays and functions

related with heating.)

5.COOL button

Used to set COOL operation.

6.SMART button

Used to set SMART operation.

(This function is unavailable

on some models.)

7.Display of each function

status

8.Operation mode display

9.Signal sending end

10.Signal sending display

11.TEMP display

12.FAN SPEED display

Swing up/down display Left/right air flow display

13.TIMER ON display

TIMER OFF display CLOCK display

14.ON / OFF button

15.TEMP. button

16.FAN SPEED button

Used to select fan speed: LOW,MED,HI,AUTO

17.FOLLOW / EVADE button

Detect the location where the human body is, adjust the air deflector to blow/avoid the body.

Operation

Inner side of the controller

SMART

SET TEMP.

AUTO AUTO

FAN SPEED

TIMER ON OFF

AM PM

ROOM TEMP.

AUTO

COOL HEAT

FAN DRY CTD

POWER SOFT

ECO

iFP

SMART

18.CODE button

Used to select CODE A or B

with a press, A or B will be displayed on LCD.Please select A without special explanation.

19.RESET button

When the remote controller

appears abnormal,use a sharp pointed article to press this button to reset the controller normal.

20.INQUIRE button

Inquire the external environmental temperature and the operating power of the machine. (e.g. when the panel display

“01”, the

This function unavailable on this models.

Loading of the battery

perating power is 100W; when the panel display the operating power

and so forth)

00W,

21.LIGHT button

Control the lightening and extinguishing of the indoor LED display board. The manual of how to change the default display temp： Press LIGHT button

continuously for ten times, the display temp on display panel

can be changed between ambient temp and set temp.

22.POWER / SOFT button

23.

special heating set function: 10 degree heating maintaining

(valuable for RS)

24.HEALTH AIRFLOW

button

25.HEALTH button

26.SWING UP/DOWN button

27.SWING LEFT/RIGHT

button

28.FRESH button

29.SLEEP button

30.TIMER ON / OFF button

31.HOUR button

32.CANCEL/CONFIRM

button

Used to confirm timer and clock settings.

33.CLOCK button

34.LOCK button

If pressed, the other buttons

will be disabled. Press it once again,lock will be cancelled.

Load the batteries as illustrated. 2 R-03 batteries,resetting key(cylinder); Be sure

“02”,

that the loading is in line with the" + "/"-";

Load the battery,then put on the cover again.

Clock set

Press CLOCK button,

"AM" or "PM" flashes.

Press “+” or “-” to set

correct time.

AM PM

SMART

Note:

The distance between the signal transmission head and the

receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change-over

wireless telephone is installed in the type fluorescent lamp or

room, the receiver is apt to be disturbed in receivingthe signals,

so the distance to the indoor unit should be shorter. Full display or unclear display during operation indicates the batteries have been used up.Please change batteries.

If the remote controller can’t run normally during operation,

please remove the batteries and reload several minutes later.

Each press will increase or decrease 1min.If the button is kept pressed,time will change quickly.

Confirm time.

After time setting is confirmed, press CONFIRM,"AM "and "PM" stop flashing,while clock starts working.

Remove the battery cover;

Hint:

Remove the batteries in case unit won’t be in usage for a long period.If there are any display after taking-out,just need to press reset key.

Operation

SMART Operation

(This function is unavailable on

SMART

some models)

One key can give you a comfortable room! The air conditioning unit can judge the indoor temperature and humidity, and make the adjustment accordingly.

SMART

Press ON/OFF button, unit starts.

Press SMART button“ ” is

displayed on the remote controller

and “ ” is displayed on the

display board,unit will run in SMART

SMART start

SMART

COOL,HEAT and DRY Operation

Unit start.

the remote

SMART

Select operation mode.

Press COOL button“ ”

is displayed on

controller and “ ” is displayed on the display board,

unit will run in COOL mode.

mode.

SMART Defrost SMART FAN SPEED SMART FAN HEALTH SMART DRY SMART SOFT SMART Control temperature

SMART

Under the cooling, heating and dehumidifying mode, press the smart key to enter the smart function. Under the smart running mode, when the air conditioning is running, it will automatically select cooling, heating, dehumidifying or blowing mode as per the setting temperature. When the smart function is running, press the “cooling” “heating” or “dehumidifying” key to switch to the other mode, you will exit from the smart function.

SMART stopsor

Press HEAT button“ ” is displayed on the remote

controller and “ ” is displayed on the display board,

unit will run in HEAT mode.

Press DRY button“ ” is displayed on the remote controller and “ ” is displayed on the display board, unit will run in DRY mode.

1.In DRY mode, when room temperature becomes lower than temp.setting+2 unit will run intermittently ai LOW speed regardless of FAN setting.

2.Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status.

Operation

Select TEMP.setting FAN Operation

Press TEMP.setting

Press TEMP button.

Every time the button is

SMART

pressed, temp. setting increases 0.5

Every time the button is pressed, temp. setting

decreases 0.5

Unit will start running to reach the temp.setting on LCD.

SWING Operation

Up and down air flow direction

For each press of “ ” button,

air flow direction on remote

SMART

controller displays as follows according to different operation

modes:

COOL/DRY:

HEAT:

SMART:

Initial state

FAN Operation

Press FAN SPEED button. For each press, fan speed

changes as follows:

LOW

Unit will run at selected fan speed.

MED HI

AUTO

Left and right air flow direction

For each press of “ ” buttor,remote controller displays as follows:

remote controller:

Initial state

When humidity is high,condensate water might occur at

air outlet if all vertical louvers are adjusted to left or right. It is advisable not to keep horizontal flap at downward

position for a long time in COOLor DRY mode ,

otherwise, condensate water might occur.

As cold air flows downward in COOL mode, adjusting air flow horizontally will be

better air circulation.

much more helpful for a

Operation

HEALTH Operation

The anion generator in the airconditioner can generate a

lot of anion effectively balance

quantity of position and

the

anion in the air and also to kill bacteria and speed up the dust

SMART

sediment

clean the air in the room.

For each press, is displayed

in the room and finally

Press HEALTH button

HEALTH AIRFLOW Operation

The setting of health airflow

function

1).Press the button of health airflow, appears on the display. Avoid

the strong airflow blows direct to

SMART

the body.

2).Press the button of health airflow

again, Avoid the strong direct to the body.

appears on the display.

airflow blows

The cancel of the health airflow function

Air conditioner starts health anion function operation.

Press HEALTH button for twice press,

disappears,the operation stops.

When indoor fan motor is running, it has healthy process function. (It’s available under any mode) When the fan in the indoor unit does not work, the health lamp lights up, but the anion generator

does not release anion.

Press the button of health airflow again, both the inlet and outlet

grills of the air conditioner are opened, and the unit

goes on working under the condition before the

setting of health airflow function. After stopping, the outlet grille will close automatically.

Notice:

Cannot pull direct the outlet grille by hand. Otherwise,the grille will run incorrectly. If the grille is not run correctly, stop for a minute and then start, adjusting by remote controller.

Remote controller can memorize each operation status. when starting it next time, just press ON/OFF button and unit will run in previous status.

Note:

1.After setting the health airflow function, the position of inlet and outlet grills is fixed.

2.In heating, it is better to select the mode.

3.In cooling, it is better to select the mode.

4.In cooling and dry, using the air conditioner for a long time under the high air humidity, water occurs at the outlet grille .

5.Select the appropriate fan direction according to the actual conditions.

a phenomenon falling drips of

Operation

POWER/SOFT Operation

POWER Operation

When you need rapid cooling, you can use this function.

For each press, is displayed Air conditioner

POWER function operation.

In COOL mode, fan speed automatically takes high speed of AUTO fan mode.

Press POWER button again,

POWER

disappears,the operation

stops.

POWER

SOFT

SMART

AUTO

starts

TIMER Operation

Set Clock correctly before starting Timer operation.You can let unit start or stop automatically a following times:Before you wake up in the morning,or get back from outside or after you fall asleep at night.

Select your desired operation

mode.

Select your desired TIMER ON.

SMART

TIMER ON

Remote controller: " will flash.

Select your desired TIMER OFF.

Remote controller: " will flash.

Time setting.

TIMER ON

TIMER OFF

SOFT Operation

You can use this function when

silence is needed for rest or reading.

For each press, is displayed Air conditioner

starts POWER function operation.

In SOFT operation mode, fan speed automati cally takes low speed of AUTO fan mode.

Press SOFT button again,

operation stops.

SOFT

disappears,the

SOFT

Hints:

During POWER operation, in rapid COOL mode, the room will show inhomogeneous temperature

distribution.

Long period SOFT operation will cause effect of not too cool or not too warm.

Every time the button is pressed, time setting increases or

decreases 1 min, if kept depressed, it will increase

rapidly. It can be adjusted within 24 hours.

Confirming your setting.

After setting correct time, press CONFIRM button press

"or"

OFF

CONFIRM button to confirm " remote controller stops flashing.

TIMER ON

press TIMER ON button to confirm, follow the same procedure in "Time setting for TIMER OFF "

Remote controller: press TIMER OFF button to confirm, follow the same procedure in "Time setting for TIMER ON "

Remote controller:

OFF

TIMER ON

OFF

OFFTIMER ON

OFF

" on the

To cancel TIMER mode

Just press CANCEL button several times until TIMER mode disappears.

Operation

Comfortable SLEEP

Before going to bed,you can simply press the SLEEP button

you a sound sleep.

and unit will operate in SLEEP mode and bring

3 hours then stops. Temp. is lower than temp. setting so that room temperature won’t be too high for your sleep.

SMART

SLEEP operation starts

AUTO

Press SLEEP button.

Operation Mode

1.In COOL,DRY mode

1 hours after SLEEP mode

starts, temp.will become 1 higher than temp.setting. After another 1 hours, temp. rises

by 1 further. The unit will run for further 6 hours then stops Temp.is higher than temp. setting so that room temperature won’t be too low for your sleep.

operation stops

Approx.6hrs

SLEEP

Unit stop

Temp.setting

1 hr

Decreases 2

1 hr

Decreases 2

3 hrs

SLEEP

operation starts

Rises 1OC

SLEEP

operation stops

In HEAT mode

3.In SMART mode

The unit operates in corresponding sleep mode, which adapted to the automatically selected operation mode.

4.When quiet sleeping function is set to 8 hours the quiet sleeping time can not be adjusted.When TIMER function is set,the quiet sleeping function can't be set up.After the sleeping function is set up,if user resets

TIMER function, the sleeping function will be cancelled; the machine will be in the state of timing-on,if the two modes are set up at the same time, either of their operation time is ended first ,the unit will stop automatically, and the other mode will be cancelled.

Unit stop

1 hr

Temp.setting

1 hr

Rises 1

In COOL, DRY mode

2.In HEAT mode

1 hours after SLEEP mode starts,temp will become 2

lower than temp.setting. After another 1 hours, temp

decrease by 2 further. After more another 3 hours, temp. rises by 1 further. The unit will run for further

Power Failure Resume Function

If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed.

When the power resumes after power failure, the unit will run automatically, and 3 minutes later the compressor starts running.

Note to the power failure resume:

press the sleep button ten times in five seconds and enter function after hearing four sounds.And press the sleep button ten times within five seconds and leave this function after hearing two sounds.

Operation

iFP Operation

The movement of people in the room can be sensed, which can improve the air adjustment efficiency.

iFP

BLANK

iFP

SMART

Press iFP button “ ” is displayed on the remote controller

and “ ” is displayed on the

display board, unit will unrin

iFP mode.

Every time the button is pressed, display changes as follows: Remote controller:

ECO Operation

Automatic adjusting with the environmental temperature, running with power saving.

ECO

SMART

Press ECONOMY button “ ”

is displayed on the remote

controller,unit will run in

ECONOMY operation.

Press ECONOMY button For

twice press, ECONOMY

disappears, the operation stops.

Detect the location of the human body, adjust the wind swing,blow the location where the body is.

Detect the location of the human body,adjust the wind swing,avoid the location where the body is.

When several people are located at different positions,or one person is moving in different areas, no matter whether the wind is blowing or not, the wind will automatically swing and blow to multi areas, the wind direction adjustment will

be delayed, it cannot be deflected suddenly while detecting.

In iFP,FOLLOW and EVADE operation mode, Press“ ”

button, the unit will not operate “ ” mode, Press “　　” button, the operation stops.

The human body sensor is used to detect if the infrared

ray is changing. It may be inaccurate in the following

conditions:

The human body keeps still (when reading or watching TV etc.) or is blocked by barriers like screen, cabinet

or glass. The person is wearing very thick clothes or the person

is lying or sleeping. A pet is moving frequently, or the wind is blowing the curtains, or something in the room is swinging frequently.

The power saving function only works under the cooling, heating or dehumidifying mode, after the power saving function is set, press the sharp, mute, sleep, or smart key to exit the power saving function.

After the power saving is set, the host machine will automatically adjust the setting temperature, and automatically control the switch of the compressor, which may be inconsistent with

the user’s setting. The power saving function is more effective

after the air conditioning has been running for a long time (more than 2 hours)

Operation

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote

controller is defective or lost. When the emergency operation switch is pressed,the"Pi" sound is heard once, which means the start of this operation. In this operation,the system automatically selects the operation modes,cooling tor fan or heat, according to the room temperature.

Operation mode

COOLING

HEAT

Operation mode

FAN

Designated

temperature

Designated

temperature

Timer

mode

NO NO

Timer

mode

AUTOMATIC AUTOMATIC

AUTOMATIC

Room

temperature

ABOVE 23

BELOW 23

(cooling only uint)

Room temperature

BELOW 23

It is not possible to operate in dry mode.

Test operation:

Test operation switch is the same as emergency switch.

Use this switch in the test operation when the room

not use it in the normal operation. Continue to press the test operation switch for more than 5 seconds. After you hear the

your finger from the switch:the cooling operation starts with the air flow speed

temperature is below 16 C, do

"Hi".

"Pi" sound twice,release

Air flow

Pi Pi

For smart Use of The Air Conditioner

Air Filter cleaning

Open the inlet grille by pulling it upward

Remove the filter

Push up the filter’s center tab slightly until it is released from the stopper, and remove the filter downward.

Clean the filter

Use a vacuum cleaner to remove dust, or wash the filter with water. After washing, dry the filter completely in the shade.

Attach the filter

Attach the filter correctly so that the “FRONT” indication is facing to the front. Make sure that the filter is completely fixed behind the stopper. If the right and left filters are not attached correctly, that may cause defects.

Close the inlet grille

Once every two weeks

Cautions

WARNING

Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.

WARNING

When abnormality such as burnt-small found,

immediately stop the operation button and

contact sales shop.

Use an exclusive power source with a circuit

breaker

Check proper installation of the drainage securely

OFF

Connect power supply cord to the outlet completely

STRICT

ENFORCEMENT

Do not use power supply cord in a bundle.

ENFORCEMENT

Take care not to damage

the power supply cord.

PROHIBITION

Do not start or stop the operation by disconnecting the power supply cord and so on.

PROHIBITION

Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.

Do not channel the air flow directly at people, especially at infants or the aged.

STRICT

Use the proper voltage

STRICT

ENFORCEMENT

PROHIBITION

CAUTION

Take fresh air occasionally especially when gas appliance is running at the same time.

STRICT

ENFORCEMENT

1.Do not use power supply cord extended or connected in halfway

Do not install in the place where there is any

possibility of inflammable gas leakage around the unit.

3.Do not get the unit exposed

to vapor or oil steam.

PROHIBITION

Do not insert objects into the air inlet or outlet.

PROHIBITION

Do not try to repair or reconstruct by yourself.

Do not operate the switch with wet hand.

Connect the earth cable.

earthing

Do not install the unit near a fireplace or other heating apparatus.

Do not place animals or plants in the direct path of the air flow

PROHIBITION

STRICT

ENFORCEMENT

Check good condition of the installation stand

PROHIBITION

Do not place any objects on or climb on the unit.

PROHIBITION

Do not pour water onto the unit for cleaning

PROHIBITION

Do not place flower vase or water containers on the top of the unit.

PROHIBITION

Trouble shooting

Before asking for service, check the following first.

Cause or check points

When unit is stopped, it won't restart

immediately until 3 minutes have

elapsed to protect the system. When the electric plug is pulled out

and reinserted, the protection circuit will work for 3 minutes to protect the

air conditioner.

During unit operation or at stop, a swishing or gurgling noise may be heard.At first 2-3 minutes after

unit start, this noise is more noticeable. (This noise is generated by refrigerant flowing in the system.)

During unit operation, a cracking noise may be heard.This noise is

generated by the casing expanding or shrinking because of temperature changes.

Should there be a big noise from

air flow in unit operation, air

filter may be too dirty.

This is because the system circulates smells from the interior air such as the smell of furniture, paint, cigarettes.

During COOL or DRY operation,

indoor unit may blow out mist. This is due to the sudden cooling of indoor air.

In DRY mode, when room temperature becomes lower than temp. setting+2

intermittently at LOW speed

regardless of FAN setting. Is power plug inserted?

Is there a power failure? Is fuse blownout?

Is the air filter dirty?

Normally it should be cleaned

every 15 days. Are there any obstacles before inlet and outlet? Is temperature set correctly? Are there some doors or

windows left open? Is there any direct sunlight through the window during the

cooling operation?(Use curtain)

Are there too much heat sources or too many people in the room during cooling operation?

C,unit will run

Normal Performance inspection

Multiple

check

Phenomenon

The system does not restart immediately.

Noise is heard

Smells are generated.

Mist or steam are blown out.

In dry mode, speed can’t be changed.

Poor cooling

fan

Cautions

Do not obstruct or cover the ventilation

conditoner.Do not put fingers

inlet/outlet and

Do not allow children to play with the air

case should children be

swing louver.

or any other things into the

allowed to sit on the outdoor unit.

Specifications

The refrigerating circuit is leak-proo f.

The machine is adaptive in following

1.Applicable ambient temperature range:

Indoor

Cooling

Outdoor

Indoor

Heating

Outdoor

(INVERTER)

2. If the power supply cord is damaged, it manufacturer

3. If the fuse of indoor unit on PC board is

it with the type of

broken,change it with the type of

4. The wiring method should be in line with

5. After installation, the power plug should

6. The waste battery should be disposed

7. The appliance is not intended for use

persons

8.Young children should be supervised

the appliance.

with

9. Please employ the proper power plug, cord.

10. A breaker should be incorporated into

should be

contacts should be not less than

11 .The power plug and connecting cable

attestation.

12.In order to protect the units,please turn

30 seconds

13.Please don't insert any sensor on 3-way

or its service agent or a similar

without supervision.

all-pole switch and the distance

later, cutting off the power.

Maximum:D.B/W.B

Minimum:D.B/W.B

Maximum:D.B/W.B

Minimum:

Maximum:D.B

Minimum:

Maximum:D.B/W.B

Minimum:D.B/W.B

Maximum:D.B/W.B

Minimum:D.B

T. 3.15A/ 250V

3mm.

grille of the air

conditioner

D.B

must be replaced

broken,please

. If the fuse of

T.25A/250V

the local wiring

be easily reached.

properly.

by young children or

to ensure that th

which fit into the

fixed wiring. The

between

must have

off the A/C first,

stop valve pipe

situation

32oC/23oC

C/15oC

C/26oC

27 0oC

C/18oC

C/-8oC

C/18oC

-15

qualified

outdoor

its two

acquired the local

.In no

by the

person.

change

unit is

standard.

infirm

do not play

ower supply

breaker

and at least

fitting.

EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS

All the products are in conformity with the following European provision:

- Low Voltage Directive 73/23/EEC

- Low Voltage Directive 2006/95/EC

-Electomagnetic CompatibilitY 89/336/EEC

-Electomagnetic CompatibilitY 2004/108/EC

ROHS

The products are fulfilled with the requirements in the directive 2002/95/EEC of the European parliament and of council on the Restriction of the use of

Certain Hazardous Substances in Electrical and Electronic Equipment (EU

RoHS Directive)

WEEE

In accordance with the directive 2002/96/CE of the European parliament, herewith we inform the consumer about the disposal requirements of the electrical and electronic products.

DISPOSAL REQUIREMENTS:

Your air conditioning product is marked with this symbol.This means that electrical and electronic products shall not be mixed with unsorted household waste. Do not try to dismantle the system yourself : the dismantling of the air conditioning system, treatment of the refrigerant, of oil and of other part must be done by a qualified installer in accordance with relevant local and national legislation. Air conditioners must be treated at a specialized treatment facility for reuse, recycling and recovery. By ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and humen health. Please contact the installer or local authority for more information. Battery must be removed from the remote controller and disposed of separately in accordance with relevant local and nationl legislation.

Componentes y funciones



Unidad interior

Toma de entrada

Filtro SXUL¿FDGRU de aire

(interior)

Rejilla de

entrada

de aire

Salida

de aire

Generador de aniones negativos

(permite ajustar la dirección del ÀXMR de aire hacia arriba y hacia abajo; no lo ajuste manualmente)

(interior)

Alerón horizontal

Ojo

inteligente

Paleta vertical

(permite ajustar la dirección del ÀXMR de aire hacia la izquierda

y hacia la derecha)

Recuerde que la ilustración anterior podría no reflejar fielmente el producto adquirido y debe utilizarse únicamente como referencia.

Panel de indicadores

2UL¿FLR del receptor de señal

Indicador iFP

Indicador de la función SALUDABLE

(Si la unidad que ha adquirido dispone de función saludable, préstele atención. De lo contrario, ignórelo).

rodacidnI TEMPORIZADOR DE ENCENDIDO/APAGADO INDICADOR TEMPORIZADOR DE ENCENDIDO-APAGADO Indicador de la función SUEÑO

Indicador de temperatura

El indicador de temperatura incluye dos tipos de visualización.

Uno muestra temperatura ambiente y el otro la temperatura establecida. La temperatura que se muestra se puede cambiar entre temperatura ambiente y temperatura establecida mediante una operación especial.

Indicador del modo INTELIGENTE

Indicador de REFRIGERACIÓN

Indicador del modo SECO

Indicador del modo CALOR



Interruptor de

emergencia

Panel de indicadores



Parte externa del mando

1. Botón iFP

2. Botón AHORRO

3. Botón SECO

4. Botón CALOR

Unidad exterior

SALIDA DE AIRE NÓIXENOCEDSOBUT Y

ENTRADA DE AIRE MANGUITO DE DRENAJE

Mando a distancia

SMART COOL

HEAT FAN DRY CTD

POWER

SOFT

ECO

iFP

SMART ON/OFF

COOL

HEA

ECONOMY FAN SPEED

iFP

Intenta provocar que la persona se mueva para controlar el funcionamiento del Àujo de aire y del ahorro de energía.

Se utiliza para establecer el funcionamiento en AHORRO.

Se utiliza para establecer el funcionamiento en SECO.

Se utiliza para establecer el

SET TEMP.

AUTO AUTO

FAN SPEED

AM PM

ROOM TEMP.

AUTO

TIMER ON OFF

ADE

CABLEADO ELÉCTRICO

funcionamiento en CALOR. Las unidades que sólo dispongan de funciones de refrigeración no poseen pantallas y funciones relacionadas con calefacción.

5. Botón FRÍO

Se utiliza para establecer el funcionamiento en FRÍO.

6. Botón INTELIGENTE

Se utiliza para establecer el funcionamiento en INTELIGENTE. Esta función no está disponible en algunos modelos.

7. Mostrar el estado de cada función

8. Indicador de modo de funcionamiento

9. Extremo de de envío de señal

10. Indicador de envío de señal

11. Indicador de TEMPERATURA

12. Indicador de VELOCIDAD DE VENTILADOR

Indicador de balanceo vertical Indicador de ÀXMR de aire horizontal

13. Indicador de TEMPORIZADOR DE ENCENDIDO Indicador de TEMPORIZADOR DE APAGADO Indicador de RELOJ

14. Botón ENCENDIDO / APAGADO

15. Botón TEMPERATURA

16. BOTÓN VELOCIDAD DEL VENTILADOR

Se utiliza para seleccionar el nivel de velocidad del ventilador: BAJA, MEDIA, ALTA y AUTOMÁTICA

17. Botón SEGUIR / ELUDIR

Permite detectar la ubicación en la que hay una persona y ajustar el deÀector de aire para dirigirlo hacia esa persona o para eludirla.

Funcionamiento

Parte interna del mando

SMART

SET TEMP.

AUTO AUTO

FAN SPEED

TIMER ON OFF

AM PM

ROOM TEMP.

AUTO

21. Botón LUZ

22. Botón INTENSO / SUAVE

23. 10

COOL

HEAT

FAN DRY CTD

POWER SOFT

ECO

iFP

SMART

18. Botón CÓDIGO

Permite seleccionar el CÓDIGO A o B al pulsarlo. La pantalla LCD mostrará A o B, según el código elegido. Seleccione el código A si no ha recibido ninguna indicación.

19. Botón RESTABLECER

Si el mando a distancia presenta alguna anomalía, introduzca un objeto puntiagudo a través del

para pulsar este botón y restablecer el mando a distancia.

20. Botón CONSULTAR

Consulta la temperatura ambiente externa y la potencia de funcionamiento de la máquina. (p. ej. cuando el panel muestra “01”,

Esta función no está disponible en este modelo.

24. Botón FLUJO DE AIRE

25. Botón SALUDABLE

26. Botón OSCILACIÓN

27. Botón OSCILACIÓN

28. Botón FRESCO

29. Botón SUEÑO

30. Botón TEMPORIZADOR

31. Botón HORA

32. Botón CANCELAR/

33. Botón RELOJ

34. Botón BLOQUEAR

Instalación de las pilas

la potencia de funcionamiento es de 100 W; cuando el panel muestra “02”, la potencia de funcionamiento es de 200 W, y así sucesivamente)

Controla la activación y desactivación de la iluminación del panel de indicadores LED de la unidad interior. Cómo cambiar la temperatura predeterminada del indicador: Presione el botón LUZ continuamente Presione el botón LUZ continuamente diez veces. La temperatura mostrada en el panel de visualización se puede cambiar entre la temperatura ambiente y la temperatura establecida.

función de calefacción especial: mantenimiento de calefacción de 10 grados (valioso para RS)

SALUDABLE

VERTICAL

HORIZONTAL

DE ENCENDIDO / APAGADO

CONFIRMAR

Se utiliza para la de reloj y temporizador.

se deshabilitarán. Pulse de nuevo este botón para cancelar el bloqueo.

carga de las pilas. 2 pilas R-03, botón de restablecimiento (botella). Asegúrese de que las pilas se insertan con la polaridad "+"/"-" correcta.

Instale las pilas y vuelva a colocar de nuevo la tapa.

Configuración del reloj

Pulse el botón RELOJ.

A continuación, comenzará a

parpadear el indicador "AM" o "PM".

Pulse “+” o “-” para

establecer la hora correcta.

AM PM

En la figura se muestra el modo de

SMART

Nota:

La distancia entre el cabezal de transmisión de la señal y el orificio del receptor debe ser de unos 7 m sin obstáculos. Si se instalan lámparas fluorescentes de arranque electrónico o se utilizan teléfonos inalámbricos en la sala, el receptor podría resultar perturbado al recibir las señales, por lo que la distancia hasta la unidad interior deberá ser menor. Si se activan todos los indicadores de la pantalla o no es posible visualizarlos correctamente durante el uso, es señal de que las pilas se han agotado. Por favor, cámbielas. Si el mando a distancia no funciona normalmente durante su uso, extraiga las pilas y vuelva a instalarlas pasados unos minutos.

Cada vez que pulse un botón, la hora se aumentará o reducirá en 1 minuto. Si mantiene un botón pulsado, la hora avanzará o retrocederá rápidamente.

Una vez la

el botón CONFIRMAR. Tras hacerlo, el indicador “AM” o “PM ” dejará de parpadear y el reloj se pondrá en marcha.

la hora.

de hora, pulse

Extraiga la tapa de las pilas;

Sugerencia:

Extraiga las pilas si no tiene intención de utilizar la unidad durante un periodo largo de tiempo. Si observa alguna pantalla extraña después de extraer las pilas deberá pulsar el botón de reinicio.

Funcionamiento

Funcionamiento en modo INTELIGENTE

(Esta función no está disponible

SMART

en algunos modelos)

¡Puede conseguir una habitación confortable con un solo botón! La unidad de aire acondicionado puede analizar la temperatura y la humedad interiores y realizar el ajuste en consecuencia.

SMART

Presione el botón de ENCENDIDO/ APAGADO para arrancar el equipo. Pulse el botón INTELIGENTE.

SMART

“ distancia y “

panel de indicadores. La unidad entrará en el modo INTELIGENTE.

inicia el modo INTELIGENTE

” se mostrará en el mando a

” se mostrará en el

Funcionamiento en modo FRÍO, CALOR y SECO

Arranque de la unidad.

” se mostrará

SMART

Seleccione el modo de

funcionamiento.

Pulse el botón FRÍO. “ se mostrará en el mando a

distancia y “ en el panel de indicadores.

La unidad entrará en el modo FRÍO.

”

INTELIGENTE Descongelar INTELIGENTE VELOCIDAD DEL VENTILADOR INTELIGENTE VENTILADOR SALUDABLE INTELIGENTE SECO INTELIGENTE SUAVE INTELIGENTE Temperatura de control

SMART

o detiene el modo INTELIGENTE

En el modo de refrigeración, calefacción y deshumidificación, pulse el botón INTELIGENTE para entrar en la función inteligente.

En el modo Inteligente, cuando el aparato de aire acondicionado está funcionando, seleccionará automáticamente refrigeración, calefacción o ventilación según la temperatura establecida.

Cuando la función Inteligente esté activa, pulse el botón de “refrigeración”, “calefacción” o “deshumidificación” para cambiar a otro modo y salir de la función Inteligente.

Pulse el botón CALOR. “ ” se mostrará en el mando a distancia y “ unidad entrará en el modo CALOR.

Pulse el botón SECO. “ ” se mostrará en el mando a distancia y “ unidad entrará en el modo SECO.

1. En el modo SECO, cuando la temperatura de la sala es inferior a la temperatura configurada +2ºC, el equipo funcionará de forma intermitente a BAJA velocidad, independientemente de la configuración del ventilador.

2. El mando a distancia permite memorizar cada estado de funcionamiento. Al arrancar el equipo la próxima vez sólo necesitará pulsar el botón ENCENDIDO/ APAGADO. El equipo se activará en su estado anterior.

” se mostrará en el panel de indicadores. La

Funcionamiento

Seleccionar un valor de



TEMPERATURA, funcionamiento en VENTILADOR

Pulse el valor

TEMPERATURA

Pulse el botón TEMPERATURA.

Cada vez que pulse el

SMART

botón, la temperatura aumentará 0.5

Cada vez que pulse el botón, la temperatura aumentará 0.5



Funcionamiento en modo OSCILACIÓN

Dirección de ÀXMR de aire

vertical

Cada vez que se pulse el botón “

SMART

”, la dirección del ÀXMR de aire en el mando a distancia se mostrará de la siguiente manera, según los distintos modos de funcionamiento:

FRÍO/SECO:

CALOR:

El equipo comenzará a funcionar al alcanzar la temperatura en la pantalla LCD.

Funcionamiento en modo VENTILADOR

Pulse el botón VELOCIDAD DEL VENTILADOR. Cada vez que pulse el botón, la velocidad del ventilador cambiará de acuerdo con el ciclo ilustrado a continuación:

LOW

La unidad funcionará a la velocidad de ventilador seleccionada.

MED HI

AUTO

INTELIGENTE:

Estado inicial

Flujo de aire en dirección hacia la izquierda y la

derecha

Cada vez que pulse el botón , en la pantalla del mando a distancia aparecerá lo siguiente: mando a distancia:

Estado inicial

Si el nivel de humedad es alto podría condensarse humedad en la salida de aire si se ajustan todas las lamas verticales a la izquierda o la derecha.

Es aconsejable no mantener la aleta horizontal en posición descendida durante mucho tiempo en el modo FRÍO o SECO. De lo contrario podría producirse condensación de agua.

Al fluir el aire frío hacia abajo en el modo FRÍO, ajustar el flujo de aire en dirección horizontal será de mucha más ayuda para una mejor circulación del aire.

+ 42 hidden pages