Haier AS09GS1ERA, AS07GS1ERA, AS12GS1ERA, HUM09HC03-R2, HUM12HC03-R2 User Manual

...

SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL

Contents

AS07GS1ERA AS09GS1ERA AS12GS1ERA

PARTS AND FUNCTIONS OPERATION INDOOR UNIT INSTALLAION

MAINTENANCE CAUTIONS TROUBLE SHOOTING

5 9 10 11

●

Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

0010535380

Parts and Functions

Indoor Unit

Inlet

Inlet grille

Outlet

Vertical blade

(adjust left and

Horizontal flap

right air flow)

(adjust up and down air flow.

Don't adjust it manually)

Please be subject to the actual produce purchased the above picture is just from your reference

Display board

Emergency

Switch

Air Purifying Filter

(inside)

Outdoor Unit

Remote controller

1. Mode display

Operation mode

Remote controller

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

ON/OFF

FAN

MODE

SWING

POWER/SOFT

TIMER

OCK

LIGHT

SLEEP

SET

LOCK

COOL DRY

HEAT

AUTO

LO MED HIAUTO

9. CLOCK display

10.TEMP display

7 8

11. POWER ON/OFF button

12. MODE button

13. FAN button

14. HOUR button

15. SWING button

16. SLEEP button

17. LOCK button

Used to lock buttons and LCD

display.

18. TEMP.SETTIN button

19. SET / LIGHT button

20. TIMER button

21. CLOCK button Used to set correct time.

22. RESET button When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal.

FAN

23. HOUR / POWER/SOFT button Used to set clock and timer setting. Every time the button is pressed, display changes as follows:

BLANK

SOFT

OWER

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE



Please be subject to the actual produce purchased the above picture is just from your reference

Clock set

Press CLOCK button, "AM" or "PM" flashes.

Press or to set correct time. Each press

or decrease 1min. If the

change quickly.

After time setting is confirmed,press SET,

button is kept pressed,time will

"AM "and "PM" stop flashing,while clock starts working.

CLOCK

LOCK

TIMER

LIGHT

SET

will increase

POWER/SOFT

SLEEP

RESET

Loading of the battery

Remove the battery cover;





Load the battery,then put on the cover again.

Note:

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-sta rted type fluorescent lamp or change- over

type fluorescent lamp or room, the recei

ver is apt to be disturbed in receiving

so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the

ries have been used up.

batte

If the remote controller can't run normally during operation, please

remove the batteries and

Hint: Remove the batteries in case won't be in use for a long period. If there is any display after taking-out, just press reset key.



Load the batteries as illustrated.

2 R-03 batteries, resetting key



(cylinder);

Be sure that the loading

is in line with th

wireless telephone is installed in the

Please change batteries.

reload several minutes later.

e" + "/"-";

the signals,

Operation

Base Operation

ON/OFF

Remote controller



1. Unit start

Press ON/OFF on the remote controller, unit starts.

2.Select operation mode

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

AUTO COOL DRY

3.Select temp.setting

Press



Every time the button is pressed, temp.setting increase 1 rapidly

Every time the button is pressed, temp.setting decrease 1 decrease rapidly

Select a desired temperature.

button

C,if kept depressed, it will increase

C,if kept depressed, it will

4.Fan speed selection

Press FAN button. For each press, fan speed

changes as

Remote controller:

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

follows:

AUTO LO MED HI

TIMER

CLOCK

LIGHT

SET

LOCK





FAN

MODE

SWING







POWER/SOFT

SLEEP

RESET

FANHEAT

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective or lost, and with function of emergency running, air conditoner can run automatically for a while. When the emergency operation switch is pressed, the " Pi " sound is heard once, which means the start of this operation. When power switch is turning on for the first time and emergency operation starts, the unit will run automatically in the following modes:

Room temperature

Above 23oC

Below 23

Designated temperature

C 23oC

Timer

Fan

speed

AUTO

Operation

mode

COOL

HEAT

mode

emergency

operation switch

It is impossible to change the settings of temp. and fan speed,It is also not possible to operate in timer or dry mode.

Test operation:

Test ope ration switch is the same as emergency switch.

Use this switch in the test operation when the room

temperature is below 16 normal operation.

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice,

your finger from the switch: the cooling

operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor

unit will run in high speed.

C, do not use it in the

release

test operation

switch

Air Flow Direction Adjustment

1.Status display of air flow

Vertical flap

Pos.1 blank

Pos.4

2.Left and right air flow adjustment

Move the vertical blade by a knob on air

to adjust left and right direction referring to Fig.

Pos.2

(Auto swing)

Pos.3

(manual)

conditioner

Operation

Mode

AUTO

COOL

DRY

HEAT

FAN

Remote

Controller

Note

Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation

according to room temperature to AUTO the air conditioner the fan speed according to room

In DRY mode , when room temperature becomes lower than temp.setting+2 intermittently at LOW speed regardless of FAN

setting.

In HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

In FAN operation mode , the unit will not operate in COOL or

HEAT mode AUTO is not available in setting is disabled. In FAN mode, sleep operation

is not available.

When FAN is set

automatically adjusts

temperature.

C, unit will run

but only in

FAN mode ,

FAN mode.

And temp.

'

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur at air outlet if all vertical louvers are

right.

It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY

otherwise, condensate water might occur.

Note: When restart after remote turning off, the remote

controller will automatically

memorize the previous

set swing position.

adjusted to left or

mode ,

Operation

Sleep Operation

Before going to bed,you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep.

Use of SLEEP function

After the unit starts,set the operation status, then press SLEEP button before which the clock must be adjusted and time being set.

Operation Mode

1. In COOL,DRY mode

1 hours after SLEEP mode starts,temp.will become

1 higher than temp.setting.After another 1 hours,

temp.rises by 1 futher.The unit will run for further 6 hours then stops Temp. is higher than temp. setting so that room temperature won’t be too low for your sleep.

SLEEP operation starts SLEEP operation stops

Temp.setting

In HEAT mode

1 hours after SLEEP mode starts,temp will become 2 lower than temp.setting.After another 1 hours,temp decrease by 2 futher.After more another 3hours,temp.rises

by 1 futher.The unit will run for further 3 hours then stops.Temp.is lower than temp. setting so that room temperature won’t be too high for your sleep.

Temp.setting

Approx.6hrs

Rises 1

Rises 1OC

1 hr

In COOL, DRY mode

Unit stop

In AUTO mode

The unit operaters in corresponding sleep mode adapted to the automatically selected operation mode.

4. In FAN mode

It has no SLEEP function.

When quiet sleeping function is set to 8 hours

the quiet sleeping time can not be adjusted.

When TIMER function is set , the quiet sleeping function can't be set up. After the sleeping function is set up, if user resets TIMER function, the sleeping function will be cancelled; the machine will be in the state of timing-on, if the two modes are set up at the same time, either of their operation time is ended first, the unit will stop automatically, and the other mode will be cancelled.

Power Failure Resume Function

1. If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. When the power resumes after power failure, the unit will run automatically, and 3 minutes later the compressor starts running.

2. Note to the power failure resume: press the sleep button ten times in five seconds and enter this function after hearing four sounds. And press the sleep button ten times within five seconds and leave this function after hearing two sounds.

POWER/SOFT Operation

(1)

POWER Operation

When you need rapid heating or cooling, you can use this function. In COOL mode, fan speed automatically takes high speed of AUTO fan mode. In HEAT mode, fan speed automatically takes medium speed of AUTO fan mode.

(2)

SOFT Operation

You can use this function when silence is needed for rest or reading. In SOFT operation mode, fan speed

of AUTO fan mode.

Note˖ During POWER operation, in rapid HEAT or COOL modethe room

will show uniform temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm.

To cancel POWER or SOFT operation Press POWER/SOFT button again, POWER or SOFT

automatically takes low speed

disappears.

1 hr

Decreases 2OC

1 hr

SLEEP operation starts

Decreases 2

3 hrs

Rises 1OC

SLEEP operation stops

In HEAT mode

+ 7 hidden pages