Please read this operation manual before using the air conditioner.
No.0010573867
B
Operation & Installation
Manual
PACKAGED TYPE AIR CONDITIONER
Please keep this manual carefully and safely.
AP182ACBEA
ON O F
1
Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that
goes out of use, please make sure it's
inoperative and safe. Unplug the air
conditioner in order to avoid the risk of
child
entrapment.
It must be noticed that air conditioner
system contains refrigerants, which require
specialized waste disposal. The valuable
materials contained in an air conditioner
can
be recycled. Contact your local waste
disposal center for proper disposal of an
old air conditioner and contact your local
authority or your dealer if you have any
question. Please ensure that the pipework
of your air conditioner doesnot get
damaged
prior to being picked up by the relevant
waste disposal center, and contribute to
environmental awareness by insisting on
an appropriate, anti-pollution method of
disposal.
Disposal of the packaging of your
new air conditioner
All the packaging materials employed in
the
package of your new air conditioner may
be
disposed without any danger to the
environment.
The cardboard box may be broken or cut
into
smaller pieces and given to a waste paper
disposal service. The wrapping bag made of
polyethylene and the polyethylene foam pads
All these valuable materials may be taken
to a waste collecting center and used again
after adequate recycling.
Consult your local authorities for the name
and address of the waste materials
collecting centers and waste paper disposal
services nearest to your house.
Safety Instructions and Warnings
Before starting the air conditioner, read the
information given in the User's Guide
carefully. The User's Guide contains very
important observations relating to the
assembly, operation and maintenance of
the air conditioner.
The manufacturer does not accept
responsibility for any damages that may
arise due to non-observation of the following
instruction.
Damaged air conditioners are not to be
put into operation. In case of doubt, consult
your supplier.
Use of the air conditioner is to be carried
out in strict compliance with the relative
instructions set forth in the User's Guide.
Installation shall be done by professional
people, don't install unit by yourself.
For the purpose of the safety,t h eai r conditioner
must be properly grounded in accordance
with specifications.
Always remember to unplug the air
conditioner before openning inlet grill. Never
unplug your air conditioner by pulling on
the power cord. Always grip plug firmly and
pull straight out from the outlet.
All electrical repairs must be carried out
by qualified electricians. Inadequate repairs
may result in a major source of danger for
the user of the air conditioner.
Do not damage any parts of the air
conditioner that carry refrigerant by piercing
or performating the air conditioner's tubes
with sharp or pointed items , crushing or
twisting any tubes , or scraping the coatings
off the surfaces. If the refrigerant spurts
out and gets into eyes , it may result in
serious eye injuries.
2
Cautions
Do not obstruct or cover the ventilation
grille of the air conditioner. Do not put
fingers or any other things into the
inlet/outlet and swing louver.
Do not allow children to play with the air
conditioner. In no case should children be
allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
1. Applicable ambient temperature range:
2. If the power supply cord is damaged, it
must be replaced by the manufacturer
or its service agent or a similar qualified
person.
3. If the fuse on PC board is broken,please
change it with the type of T3.15A/ 250V AC.
4. The wiring method should be in line with
the local wiring standard.
5. After installation, the power plug should
be easily reached.
6. The waste battery should be disposed
properly.
7. The appliance is not intended for use by
young children or infirm persons without
supervision.
8. Young children should be supervised to
ensure that they do not play with the
applience.
9. A breaker should be used in the circuits,
which should be all-pole cutoff and the
distance between its two contacts should
be not at least 3mm .
10.Please employ the proper power plug,
which fit into the power supply cord.
(2x2.5mm +1x0.75mm )
2
11.The power plug must have acquired the
local attestation.
The machine is adaptive in following
situation
2
Cooling
Heating
Indoor
outdoor
Rated Maximum Minimum
27 32 18
19 23 14
35 43 10
24 26 6
20 27 15
14.5 -- - 7 24 -7
6 18 --
DB C
WB C
DB C
WB C
Indoor
outdoor
DB C
WB C
DB C
WB C
3
Cautions
Please read the following Safety Instructions carefully prior to use.
The instructions are classified into two levels, WARNING and CAUTION according to the
seriousness of possible risks and damages as follows. Compliance to the instructions are
strictly required for safety use.
Safety Instruction
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works may
cause electric shock, fire, water leakage.
CAUTION
Installation in an inadequate place may cause accidents. Do not install in the following place.
Connect the earth
cable.
PROHIBITION PROHIBITION
STRICT
ENFORCEMENT
Do not install in the
place where there
is any possibility
of inflammable
gas leakage around
the unit.
Do not get the unit
exposed to vapor
or oil steam.
Check proper
installation of the
drainage securely
Use fuse with specified capacity.
Replacement with steel or copper wires are
absolutely prohibited.
Grounding wire should not be connected to
that of gas pipeline, water pipeline,lighting
arrester or telephone.
FUSE
STEEL WIRE
COPPERWIRE
4
When abnormality such as burnt-small found, immediately
stop the operation button and contact sales shop.
Connect power supply cord to the
outlet completely.
After installed, the unit shall be
tested for electric leakage.
Take care not to damage the
power supply cord.
Do not use power supply cord in
a bundle.
Do not use power supply cord
extended or connected in halfway.
Do not insert objects into the air
inlet or outlet.
Do not try to repair or reconstruct
by yourself.
PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
OFF
STRICT
ENFORCEMENT
STRICT
ENFORCEMENT
Use an exclusive power source with a circuit breaker.
CAUTION
Do not use for the purpose of
storage of food, art work, precise
equipment, breeding , or cultivation.
Take fresh air occasionally
especially when gas appliance is
running at the same time.
Do not operate the switch with wet
hand.
Do not pour water onto the unit
for cleaning.
Check good condition of the
installation stand.
Do not installtheunit near a fireplace
or other heating apparatus.
Do not place animals or plants in
the direct path of the air flow.
Do not place any objects on or
climb on the unit.
Do not place flower vase or water
containers on the top of the unit.
PROHIBITION
PROHIBITION
PROHIBITIONPROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
STRICT
ENFORCEMENT
Cautions
WARNING
Use of Air Conditioner
Do not channel the air flow directly
at people, especially at infants or
the aged.
Do not start or stop the operation
by disconnecting the power supply
cord and so on.
PROHIBITION
5
Parts and Functions
2
3
4
1
Indoor unit
1.OUTLET
2.CONTROL PANEL
3.INLET
4.FILTER ( inside )
S
O OF
1.
2.
3.
4.
5.
6.
7.
8.
9.
1
2
3
4
3
5
6
7
8
9
6
Parts and Functions
EMERGENCY OPERATION AND TEST OPERATION
EMERGENCY OPERATION
MODE
TEMP
FAN
POWER
EMERGENCY SWITCH
MODE
TEMP
FAN
POWER
TEST SWITCH
Room
temperature
Designated
temperature
Timer
mode
Air flow
speed
Operation
mode
More than 26
Less than 23
26
23
Designated
temperature
None AUTO
AUTO HEA T
COOL
o
C
None
Anion
None
None
o
C
o
C
o
C
Operation
l
Carry out this operation only when the remote
controller is defective or lost.
l
Unit start
When the emergency operation switch is
pressed, a sound you can hear, which
means the start of this operation.
l
Follow the requirements below.
l
Unit stop ( to cancel emergency operation)
Press the emergency switch and hear a sound ,the unit stops.Control panel only
display the room temperature
TEST OPERATION
l
Use this switch in the test operation when the room
temperature is less 16
o
C
, do not it in the normal
operation.
l
Unit start
Continue to press the test operation switch
for more than 5 seconds. After you hear the
" Hua " sound twice,release your finger from
the switch, the test operation startsand the
air conditioner starts with the air flow speed
setting "Hi".
l
Unit stop (to cancel test operation)
Push the test run switch or operate with remote controller to cancel the test run.
If you use the remote controller to cancel the test run, the conditioner will then run as
per the working mode displayed on the remote controller.
Each time the power supply is switched off, and then is switched on, the conditioner
will play music once automatically. It will stop playing automatically when the starting
signal is received.
Push the On/Off button and Temp +/- button, the conditioner will play the reminding
sound.The On and Temp are rising tone. The Off and Temp are dropping tone.
7
8
Operation hints
9
Maintenance
Cleaning of the unit
Turn off the power switch
Do not touch with wet hand
Do not clean with hot
water or solvent
Take off the air inlet grate
First switch off the power supply,take off the
screw cap,loosen the screw with cross screwdriver .
Clean the filter
Use water or vacuum cleaner to remove
dust. If it is too dirt, clean with detergent or
neutral soap water.
Rinsing with fresh water, dry the filter and
re-assemble.
Caution:
Do not wash filter in hot water above 40 C,
which will damage the filter.
Do carefully wipe the filter.
Clean the indoor(outdoor) unit
Clean with warm cloth or neutral detergent,
then wipe away moisture with dry cloth. Do
not use too hot water(above 40 C),which will
cause discoloration or deformation. Do not
use pesticide or other chemical detergents.
10
Maintenance
Maintenance at the end of application season
On a fine day, unit shall be started and operate in
FAN mode for about half a day until the inside of
the unit becomes thoroughly dry.
Turn off the unit operation switch and power on/off.
Otherwise,there will be some electricity consumption
even the unit is in stop status.
Clean the filter and indoor,outdoor unit,cover
the units well.
Maintenance before beginning of aplication season
Check there are no obstacles in the air inlet and
outlet to avoid impairing of working efficiency.
Please do attach the air filter to ensure the
electrostatic filters not soiled.Otherwise,dirt
will come into and damage the unit or bring
failures.
11
Trouble shooting
Before asking for service, check the following first.
Cause or check pointsPhenomenon
The system does not restart
immediately.
When unit is stopped, it won't restart
immediately until 3 minutes have elasped
to protect the system.
When the electric plug is pulled out and
reinserted, the protection circuit will work
for 3 minutes to protect the air conditioner.
Normal
Performance
inspection
Noise is heard:
During unit operation or at stop, a swishing
or gurgling noise may be heard. At first 2-3
minutes after unit start, this noise is more
noticeable. (This noise is generated by
refrigerant flowing in the system.)
During unit operation, a cracking noise may
be heard. This noise is generated by the
casing expanding or shrinking because of
temperature changes.
Should there be a big noise from air flow in
unit operation, air filter may be too dirty.
Smells are generated.
This is because the system circulates smells
from the interior air such as the smell of
furniture, cigarettes.
Mist or steam are blown out.
During COOL or DRYoperation, indoor unit
may blow out mist. This is due to the sudden
cooling of indoor air.
Multiple
check
Does not work at all.
Is power plug inserted?
Is there a power failure?
Is fuse blown out?
Is the air filter dirty? Normally it should be
cleaned every 15 days.
Are there any obstacles before inlet and outlet?
Is temperature set correctly?
Are there some doors or windows left open?
Is there any direct sunlight through the
window during the cooling operation?(Use
curtain)
Are th
ere too much heat sources or too many
people in the room during cooling operation?
Poor cooling
12
Installation of indoor unit
selection of installation place
Place where it is easy to route drainage pipe
and outdoor piping.
Place ,away from heat source and with less
direct sunlight.
Place where cool and warm air could be
delivered evently to every corner of the room.
Place near power supply socket.Leave enough
space around the unit.
Place ,robust not causing vibration,where the
body can be supported sufficiently.
more than
m
ore than
more than
m
ore than
O
Installation Manua
13
Tool necessary
1. Screw driver
2. Hacksaw
3. 70mm dia.hole core drill
4. Spanner(dia. 17,27mm)
5. Spanner(14,17,27mm)
6. Pipe cutter
7. Flaring tool
8. Knife
9. Nipper
10. Gas leakage detector
or soap water
11. Measuring tape
12. Reamer
13. Refrigerant oil
Following parts shall be field
supplied
Mark
Part name
Adhensive tape
Pipe clip
Connecting hose
Insulation material
Putty
Drain hose
A
B
C
D
E
F
Note: There isn't connecting wire with this unit.
Fixing of the unit
1. Position of the wall hole
Wall hole should be decided according to installation
place and piping direction.(refer to installation drawings).
2. Making a wall hole
Drill a hole of 120X70mm dia. with a little slope towards
outside.
Indoor side
Outdoor side
Thickness
of wall
Wall hole
70mm
(Cross section of wall hole)
Installation Manual
14
3. Piping connection
Connecting method
Apply refrigerant oil at half union and flare nut.
To bent a pipe, give the roundness as large as possible not to crash the pipe.
When connecting pipe, hold the pipe center to center then screw nut on by hand, refer to Fig.
Be careful not to let foreign matters, such as sands enter the pipe.
Piping connection of the indoor unit
1. Arrangement of piping and drainage pipe
Cut away, with a hammer or a saw, the lid for piping according to piping direction.
According to the piping method, connect the piping on indoor unit with union of connection pipe.
Arrange the piping as per the wall hole and bind drain hose connecting electric cable and piping
together with polyethylene tape.
Insert the bound piping connecting electric cable and drain hoes through wall hole to connect
with outdoor unit.
2. Arrangement drain hose
Drain hose shall be placed in under place.
There should be a slope when arrange drain hose. Avoid up and down waves in drain hose.
If humidity is high, drain pipe(especially in room and indoor unit) must be covered with
installation material.
Pipe Diameter ( )
Fastening Torque
Liquid Side 6.35mm(1/4")
Gas Side 15.88mm(5/ 8") 61.8N.m
14.2N.m
Forced fastening without careful
centering may damage the
threads and cause a leakage of
gas.
After opening inlet grill, you will see a control
box as shown in the Fig.
Remove the cover before working.
Insulation material
Copper tube
Drain hose
Connecting electric cable
=for indoor and outdoor unit
Installation Manua
15
Note: When additional refrigerant is necessary, first purge air out of connecting pipe by external gas,
then drive out the excessive rerigerant by purging method.
Brand new unit is charged 80g more refrigerant than spec. This is only for first instaltion to purge air
in the indoor unit and connecting pipe.
When piping is longer than 5m, charge additional refrigerant specified in this list.
Pipe length 5m 10m 15m
Refrigerant charge(g) 90 180
Electric wiring
Note:
Electric wiring must be done by qualified person.
Use copper wire only.
The parameter of the connecting cable is H07RN-F2X2.0mm
2
,
4X0.75mm2.
Wiring of indoor unit
Insert the cable from outside the wall hole where piping already exist.
Pull it out from front.
Losen terminal screw and insert cable end fully into terminal block, then tighten it
Pull the cable gently to make sure it is tight.
Replace cover after wiring.
Wiring of outdoor unit
Insert the cable from inside the wall hole where piping already exist.
Pull it out from front.
Loose terminal screw and insert cable end fully into terminal block, then tighten it
Pull the cable gently to make sure it is tight.
Replace cover after wiring.
When connecting indoor and outdoor wire, check the number on indoor and outdoor terminal
blocks. Terminals of same number and same color shall be connected by the same wire.
Incorrect wiring may damage air conditioner's control or cause operation failure.
Note:
1(L)
Installation Manua
OUTDOOR UNIT
TERMINIAL BLOCK
INDOOR UNIT
TERMINIAL BLOCK
1 2 3
WBR
Y/G
1HP,220-230V~,50Hz
POWER SUPPLY:
Y/G
1 2 3
WBR
Y/G
Y/G
Loading...