34FV6H34FV6H
COLOUR TELEVISION
OPERATING
INSTRUCTIONS
0090508165
◆Digital I C bus control
◆Auto search tuning & 250 programs stored
◆Full infrared remote control
◆Multi-picture modes selection
◆Multi-function timer, appointing program
2
CONTENTS
WARNING AND CAUTIONS
Contents.................................................................................................................................1
Warning and Cautions...........................................................................................................2
Basic Feature.........................................................................................................................3
Technical Specifications........................................................................................................3
Function Buttons and External Sockets.................................................................................4
AV Connection.......................................................................................................................5
Remote Controller .................................................................................................................6
Control Your TV.....................................................................................................................7
Tuning Procedure.................................................................................................................10
Menu Operation...................................................................................................................11
Teletext Operation...............................................................................................................14
Television Installation.........................................................................................................17
1. When you clean the TV set, please pull
out the power plug from AC outlet.
Or may result in electric shock, fire or
damage to the TV set. Don't clean the
cabinet and the screen with benzene,
petrol and other chemicals.
2. In order to prolong the using life of the
TV set, please place it at a well ventilated
location.
3. Don't place the TV
set in direct sunlight
or near heat source.
4. Do not place the TV set near rain
or moisture as it may cause an electric
shock, or the TV set to catch fire. The TV
set must only be used
in dry indoor location.
5. The back cover must only be removed
by a registered electrical service person.
Removing the back cover may result in
electric shock, fire or damage to
the TV set.
6. If the TV set is not going to be used for
a long time, or there is a severe thunder &
lightening storm, it is recommended that
the TV set be disconnected from the AC
power outlet and the aerial plug
removed.
Connecting Other External Devices....................................................................................18
Trouble Shooting ................................................................................................................19
1
Explanation on the display tube
When the picture tube requires cleaning, please disconnect the power and use a
dry soft cotton cloth. Do not use any cleaner or abrasive cloth.
2
BASIC FEATURE
FUNCTION BUTTONS AND EXTERNAL SOCKETS
◆Digital I C bus control
2
◆Auto search tuning & 250 programs stored
◆Full infrared remote control
◆Multi-Picture modes selection
◆Multi-function timer, appointing program
TECHNICAL SPECIFICATIONS
1.POWER SUPPLY: See rating plate
2.COLOUR SYSTEM: PAL SECAM N TSC4.43/3.58(AV)
3.AUDIO SYSTEM: B/G D/K
4.CRT: 29
5.ANTENNA INPUT : 75Ω Standard Coaxial Cable
6.SOUND OUTPUT POWER: 5W+5W
7.POWER CONSUMPTION: See rating plate
8.NET WEIGHT(kg): .
9.NET DIMENSION(mm):
Supplied accessories:
Infrared remote control handset 1
Battery(AA) 2
Operating instruction 1
Design and specifications are subject to change without notice.
"
64 5
898 x 567 x 669
1.Front panel
(1)Remote sensor: let the remote
controller aim here, the TV set
can receive remote control signal.
(2)Power switch: press the button to
turn on the TV set ,press the button
again to turn off the TV set.
(3)Power indicator: the indicator lights
in standby status .The indicator
glints when you use remote
controller.
(4)Menu button
(5)Program up/down button
(6)Volume up/down button
(7)TV/AV switch button
2. The rear panel
MENU
TV/AV
- +VOL
(2)
(3)
(1)
(4)
(7)
-CH+
(5)
(6)
VIDEO
R
AUDIO
L
3
4
INPUT AND OUTPUT TERMINALS
AV CONNECTION
VIDEO
R
AUDIO
L
Power/Standby
(Ref. P7 )
Direct Access Numeric
Keys
(Ref.P7)
Quick View
(Ref.P8)
ZOOM/Teletext
(Ref.P7/Ref.P15)
REMOTE CONTROLLER
TV/AV
1
2
3
4 5 6
7
8
-/--
0
SUBCODE
PICTURE
TIMER
9
QV
MIX
TEXT
CANCEL
SOUND
?
Mute
(Ref.P8)
TV/AV Select
Re
.
f
( P8)
Call
(Ref.P8)
Child Lock
(Ref.P9)
Teletext
(Ref.P14, 15)
It can be connected to the following appliances:
video-tape recorder, video camera, tape recorder
and audio amplifier, etc......
*Please keep AC cord unplugged when connecting
TV system.
5
Teletext
(Ref.P14)
Sound Volume
Up/Down
（Ref. P7 ）
REVEAL
V-
HOLD
P+
MENU
P-
65
V+
Picture Effect
(Ref.P9)
Program Up/Down
（Ref. P7.）
MENU
(Ref.P11.)
CONTROL YOUR TV
CONTROL YOUR TV
1. Power/Stand-By ON/OFF
With Mains status On, you can also turn off using Remote Control Hand Set.
This status is called Stand-By mode. In this mode, You can also turn on the
TV bu pushing the Channel Up/Down keys on the front controls.
There is an Automatic Power OFF function in the TV. With No
Signal condition,
the TV will automatically turn off after 10 minutes.
Program Up/Down
2.
P+
V+
V-
MENU
P-
Push [P+] key to change Program Up.
Push [P-] key to change Program Down.
3
2
1
3.
1
2
Using the numeric keys on Remote
3
Control Hand Piece, channel can be
4 5 6
7
8
-/--
0
selected directly from 0 to 249 channels.
9
Or repeatedly press the -/-- button to
“ ”
select the desired mode then press numeric buttons.
“-” 1 digit mode
“ ”-- 2 digit mode
“--- ” 3 digit mode(Max Ch. 249)
4.
Volume Control
P+
V- V+
MENU
ZOOM
5.
P-
Push [V+] key for Volume Up.
Push [V-] key for Volume Down.
Push [ZOOM] key to change as follows:
NORMAL WIDE ZOOM
W ID E p icture height is reduce, ZOOM picture height is expand.
__
__
1
VOLUME 15
|||||||------------
6. TV/AV Selection
TV/AV
You can select your video source
by the [TV/AV] key.
7. MUTE
By pushing this key, sound
output will be muted.
Push [MUTE] again or Volume
Up/Down, and sound Volume
will return.
8. Quick View
QV
TV Mode: Program will quick
back to the previous
program being watched.
AV Mode: Back to TV channel.
9. CALL
TV/AV MODE
?
This key will call the on
screen display.
Push again to remove the
on screen display.
Menu MODE
Pressing the [?]key,
current menu will
exit directly.
EURO AV
3
or
AV
Program No.
Colour system
Clock
Sleep
2
EURO AV
AV
3
MUTE
1
PAL
B/G
15:15
SLEEP 120
10
2
7 8
CONTROL YOUR TV
TUNING PROCEDURE
10. Picture Effect
By repeatedly pushing this key, picture effects will change
DYNAMIC USER
MILD STANDARD
TINT setting is not included user is the last
you.
11. LOCK
By pushing the [ ] key, ---will appear on the screen.
Pressing the password the
digits that you defined yourself
correctly, the lock menu will appear.
A. Select each function by using the
[P+] [P-] keys.
B. Each value can be changed by the
[V+] [V-] keys.
C. When general lock is on, other locks
may be locked.
D. Child lock will be locked or unlocked
for current program.
E. AV LOCK will be locked or unlocked
for AV function.
F. VOL LIMIT SW will be switched on or off.
G. When you will change the password, you may be selected
NEW PASSWORD item, then push [V+] [V-] keys, the
CHANGE PASSWORD menu will appear
NEW PASSWORD: input 4 digits you like.
CONFIRM: again input above new password 4 digits correctly.
H. Press the [ ] key or [?] key, lock menu will disappear.
“ ”
setting made by
as follows.
STANDARD
LOCK
GENERAL LOCK ON
PROGRAM NO. 25
CHILD LOCK ON
AV LOCK ON
VOL LIMIT SW ON
VOL LIMIT 32
CHANGE PASSWORD
CHANGE PASSWORD
NEW PASSWORD 0 0 0 0
CONFIRM - - - -
- ---
1. AUTO SEARCH Function: Automatic Search and Memory (ASM) is
available
Antenna input.
Using [MENU] key on the front or
[MENU] key on the Remote for ASM.
A. Push [MENU] key repeatedly to
select TUNE.
B. Push [P+] or [P-] key to select
AUTO SEARCH.
C. Push [V+] or [V-] key to start ASM
and memorize into program list (0~249).
D. Wait until function has finished.
for program installation from
TUNE
BAND UHF
SKIP OFF
PROGRAM 3
SEARCH
FINE TUNE
STORE
AUTO SEARCH
2. SEARCH Function: Manual Search for Antenna input.
A. Push [MENU] key repeatedly to select TUNE.
B. Using [P+] or [P-] key, select PROGRAM. Using [V+] or [V-] key or numeric
keys to change Program Number.
C. Push [P+] or [P-] key to select BAND. Push [V+] or [V-] key to
change BAND.
D. Push [P+] or [P-] key to select SEARCH.
E. Push [V+] or [V-] key to start search.
F. Wait until function has finished.
G. Push [P+] or [P-] key to select STORE. Push [V+] or [V-] key to store.
3. FINE TUNING Function: Fine Tuning for current setting.
A. Push [MENU] key repeatedly to select TUNE.
B. Using [P+] or [P-] key to select PROGRAM. Using [V+] or [V-] key to change
Program Number.
C. Using [P+] or [P-] key to select FINE TUNE.
D. Using [V+] or [V-] key to adjust for best tuning.
E. Push [P+] or [P-] key to select STORE. Push [V+] or [V-] key to store.
Note:
The tune menu will not appear when any program would be locked.
After new password was set, the basic password 7038 still is available.
9
4. SKIP Function: Use to SKIP channels. After setting to ON, the channel will
not be selected by channel up/down keys.
A. Push [MENU] key repeatedly to select TUNE.
B. Using [P+] or [P-] key to select PROGRAM. Using [V+] or [V-]
key to change
Program Number.
10
MENU OPERATION
MENU OPERATION
C. Using [P+] or [P-] key to select SKIP. Using [V+] or [V-] to
select ON or OFF.
5. EXCHANGE Function: number and channel exchange.
A. Push [MENU] key repeatedly to select EXCHANGE.
B. Using [P+] or [P-] key to select
PROGRAM 1. Using [V+] or [V-]
EXCHANGE
key to change Program 1 Number.
C. Using [P+] or [P-] key to select
PROGRAM 2. Using [V+] or [V-]
key to change Program 2 Number.
D. Using [P+] or [P-] key to select
PROGRAM1 10
PROGRAM2 14
EXCHANGE
EXCHANGE. Using [V+] or [V-] key,
exchange is over.
MENU OPERATION
1. [MENU] key
Push [MENU] key continually to scroll through the MENU selection as
follows:
PICTURE SOUND TIME SETUP TUNE EXCHANGE
2. PICTURE MENU Function: Brightness, Contrast, Colour, Sharpness, Tint
A. Select each function using the [P+]
or [P-] key.
B. Each value can be controlled by the
[V+] or[ V-] key.
C. Repeat any functions if required.
NOTE: TINT control will be appeared
only if a NTSC signal is being
received.
PICTURE
BRIGHTNESS 48
CONTRAST 48
COLOUR 32
SHARPNESS 32
TINT
.............
3. SOUND MENU Function: Volume
A. Press SOUND menu, the volume will appear.
SOUND
B. Each value can be controlled by the [V+]or [V-]
key .
VOLUME 20
.............
4. TIME MENU Function: Time and Timer setting
A. Select TIME with the [MENU] key.
Using the [P+] or [P-] key to select
the item.
B. Using the [P+] or [P-] key to select
CLOCK, ON-TIME, OFF-TIME,
SLEEP TIMER or REMIND TIME.
C. Press [P+] or [P-] key to select minutes,
then using [V+] or [ V-] key, minutes
will change from 00 to 59. Press [P+] or
[P-] key to select hours, then using
[V+] or [ V-] key, hours will change
as follows: 0,1,..23--:--.
D. For ON-TIME, OFF-TIME or
REMIND TIME setting, using [P+]
or [P-] key to select ON PROG,
using [V+] or [ V-] key to change
On-Program number.
E. Using [P+] or [P-] key to select
SLEEP TIME, Using [V+] or [ V-] key,
sleep timer will change as follows:
0 10 20 30 40 ...160 170 180 0
5. SETUP Function: other function setting.
A. Using the [P+] or [P-] key to select
the item.
Using the [V+] or [V-] key to change
the item.
B. Using the [P+] or [P-] key to select
the COLOR SYS.
Using the [V+] or [V-] key, color sys
will change as follows:
AUTO PAL NTSC3.58 NTSC4.43 SECAM
C. Using the [P+] or [P-] key to select the AVL, AVL is auto volume level.
Using the [V+] or [V-] key, AVL will be turned OFF and ON.
TIME
CLOCK --:-ON TIME --:-ON PROG 2
OFF TIME --:-SLEEP TIMER 0
REMIND TIME --:-REMIND PROG 1
SETUP
LANGUAGE ENGLISH
COLOR SYS AUTO
SOUND SYS DK
BLUE BACK ON
BLACK STRETCH ON
AVL ON
EURO RGB
TEX LANGUAGE W-TR
CALENDAR
GAME
11 12
MENU OPERATION
TELETEXT OPERATION
D. Using the [P+] or [P-] key to select
the TEXT LANGUAGE.
Using the [V+] or [V-] key, TEXT
LANGUAGE will change as follows:
W-TR EAST1 EAST2
E. Using the [P+] or [P-] key to select
the CALENDAR.
Using the [V+] or [V-] key,
CALENDAR will appear.
After CALENDAR is appeared on the
screen:
Using the [P+] or [P-] key to change
the month.
Using the [V+] or [V-] key to change
the year.
F. Using the [P+] or [P-] key to select the GAME.
Using the [V+] or [V-] key, GAME will be appeared.
In game mode, the box will be moved to specific dot.
Push [P+] or [P-] key to move the box for up or down.
Push [V+] or [V-] key to move the box for right or left.
Push [?] key to exit game.
1 2
- - - - - - - - - - - - - - -
- - - - - - - - - - - - - - -
- - - - - - - - - - - - - - -
2004 1
Su Mo Tu We Th Fr Sa
5
4
11 12
18 19 20
25 26 27
- - - - - - - - - - - - - - -
- - - - - - - - - - - - - - -
7
6
13
8
15 16 17
14
21 22
28 29 30 31
3
9 10
23
24
1. SELECT TELETEXT MODE
Select the program which is broadcasting the TELETEXT you want to watch.
Press [TEXT] key on the remote controller and enter to TELETEXT mode.
By this key, mode will be changed as
TV TELETEXT
The overview station page or the last page viewed (in case you already watched
TELETEXT at this channel previously) appears.
If you need to return to TV mode, press again the [TEXT] key on the remote
controller.
2. PAGE SELECTION
You can enter directly desired page number with the remote controller numeric
keys 0...9 buttons.
You can sequentially select page by pressing [P+] or [P-] key.
3. HOLD
Some TELETEXT information is contained on more than one page, the pages
automatically changing after a given reading time.
Press [HOLD] key to stop the page changing (the symbol will appear on the
page heading).
Press [HOLD] key again to allow the page to change (the symbol will appear).
4. REVEAL
Some TELETEXT pages contain quiz or game question with hidden answers.
Press the [REVEAL] key to see the answers.
Press the [REVEAL] key again to hide the answers.
13
14
TELETEXT OPERATION
TELETEXT OPERATION
5. ZOOM(T/B/F Top/Bottom/Full)
To enable easier reading (larger display).
Press the [ ] key to display the TOP HALF of the page.
Press again to display the BOTTOM HALF of the page.
Press again to return to a FULL PAGE display.
Note: Changing pages reverts to a FULL PAGE display.
6. CANCEL
When a page is selected in TELETEXT mode it may take some time before it
become available, pressing the [CANCEL] key will switch to the TV mode.
When the required page is found, the page number will appear at the top of the
TV picture, press the [CANCEL] key to return to the selected TELETEXT page.
Note: You cannot change TV program while in this mode.
7. TIME
TELETEXT broadcasts sometimes transmit certain pages of information at
particular times.
To automatically display these pages when they are transmitted , select the
required page number then press [ ] key the symbol T**** are displayed
at the top of the screen, now enter the time of the broadcast Timed Page.
Example: - for 3:30 PM select 1-5-3-0 in order (24HR clock)
Example:- RED selects CITY INFORMATION
CYAN selects TRAVEL INFORMATION
GREEN selects WEATHER INFORMATION
YELLOW selects TV PROGRAMING
9. SUBCODE
Periodically revised NEWS FLASHES can be obtained from TELETEXT
broadcasts.
Select the NEWS FLASH page in TELETEXT mode then press the
[SUBCODE] key.
You can now watch the TV program and every time the News Flash page
is updated it will be automatically displayed in the TV picture.
Press the [SUBCODE] key to cause the news flash to disappear.
※ Teletext is option.
Press the [CANCEL] key to view a normal TV picture.
When the timed page is transmitted (15:30) it automatically displays the selected
page in the TV picture.
Note: To cancel, press [ ] key.
8. FAST TEXT (For possible future reference)
The RED, GREEN, YELLOW & CYAN keys are used for quick access to color
coded pages transmitted by FAST TEXT broadcast.
15
16
TELEVISION INSTALLATION
Connect antenna or video facility
1. Use 75 coaxial cable plug or 300-75 impedance converter to plug in antenna
input terminal on the rear of the cabinet.
2. Connect the video facility to the radio, video in jack on the rear of the cabinet.
VHF antenna
UHF antenna
CONNECTING OTHER EXTERNAL DEVICES
Input terminal of antenna
Co-axis antenna plug
75 Co-axis antenna plug
-
Mixer
75 Co-axis cable
Antenna in jack
Battery installation and replacement for remote control unit
The remote control uses two 1.5V AA
batteries. For installation and replacement
are as following:
1 Turn the remote control unit upside
down. Press down the grip of battery
compartment and slide the color in
the direction of the arrow.
2 Install two new batteries, make sure
that battery polarity matches with the
+,- marks inside the battery. Or not it
could damage the unit.
3 Close the battery compartment covers.
VCR or DVD player or other
To connect signal from the player,
device for playing
scart-cable would be connected
correspondingly. The device may
be to provide RGB or VIDEO or
Y/C output, you must change
EURO signal setting
correspondingly on setup menu.
SETUP
LANGUAGE ENGLISH
COLOR SYS AUTO
SOUND SYS DK
BLUE BACK ON
BLACK STRETCH ON
AVL ON
EURO RGB
TEX LANGUAGE W-TR
CALENDAR
GAME
17
18
TROUBLE SHOOTING
Before arranging for service, firstly know the status and then check simply as follows:
Problems Check
No picture or sound
Picture is OK, no sound
minimum or mute position
Remote control does not
work
No TV signal
No external video signal
Picture
picture too dark
All channels lose colour
intermittently
Poor reception, loss of
colour with certain
channels
Diagonal stripes appear
on picture
lacks colour or
Picture has snow
Check if the antenna direction has been
changed by a storm or strong wind, etc.
(because ghost images are caused by the
Ghost images appear
arrival at the antenna of both the signal
which has traveled directly from the
transmitter and the signal which has been
reflected from a hill or a large building. The
direction of the antenna should be chosen for
minimized ghosting.)
Check if the power supply is plugged in.
Check if the power switch is in ON position.
Check if the volume control is set to the
Check if the power switch is in ON position.
Check if the batteries are out of use or not
connected well.
Make sure that there is no strong light
striking the sensor window or remote control
unit
Check there are no obstacles between the
sensor window and remote control unit.
Check if the TV/AV button is not set to TV
status.
Check if the antenna is well connected.
Check if you installed the TV correctly.
Check if you installed the TV correctly.
Check if the TV/AV button is set to AV
position.
Check colour, brightness
controls are correctly
Check if the antenna is broken.
Check if the antenna is disconnected.
Check if the antenna is damaged.
Check if channels are correctly Tuned ( see
Fine Tuning).
The receiver may be affected by interference
(e.g. from nearby radio broadcasting
transmitter or from another TV receiver).
Check if the antenna is broken.
Check if the antenna is disconnected.
Check if the antenna is damaged.
and contrast
adjusted.
19
Loading...