Haier HSM09RU03, HSM12RU03, 2HUM18R03 User Manual

HSM09RU03/R2(DB) HSM09RU03/R2(DB)
2HUM18R03/R2(DB)
HSM09RU03/R2(DB)
HSM12RU03/R2(DB)
2HUM18R03/R2(DB)
No, 0010503373
Contents
Cautions Parts and functions Operation
2 6
9
22
27
Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that goes out of use, please make sure it's inop­erative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment.
It must be noticed that air conditioner system contains refrigerants, which require speciali­zed waste disposal. The valuable materials contained in an air conditioner can be recycled .Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal.
Safety Instructions and Warnings
Before starting the air conditioner, read the information given in the User's Guide caref­ully. The User's Guide contains very impor­tant observations relating to the assembly, operation and maintenance of the air conditioner.
The manufacturer does not accept respon­sibility for any damages that may arise due to non-observation of the following instruction.
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.
Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Disposal of the packaging of your new air conditioner
All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment.
The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads
contain no fluorochloric hydrocarbon.
All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.
Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.
Installation shall be done by professional people, don't install unit by yourself.
For the purpose of the safety,the air con­ditioner must be properly grounded in acco­rdance with specifications.
Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditioner.
Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries.
2
Cautions
Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver.
Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
The machine is adaptive in following situation
1.Applicable ambient temperature range:
o
32
18
43 18
27 15
24
-7
o
C/23oC
o
C/14oC
o
C/26oC
o
C
o
C
o
C
o
C/18oC
C/-8oC
Cooling
Heating
Indoor
Outdoor
Indoor
Outdoor
Maximum:D.B/W.B Minimum:D.B/W.B
Maximum:D.B/W.B Minimum:D.B
Maximum:D.B Minimum:D.B
Maximum:D.B/W.B Minimum:D.B/W.B
7. The appliance is not intended for use by young children or infirm persons without supervision.
8. Young children should be supervised to ensure that they do not play with the applience.
9.Please employ the proper power plug, which fit into the power supply cord.
10 .The power plug and connecting cable must have acquired the local attestation.
11.In order to protect the units,please turn off the A/C first, and at least 30 seconds later, cutting off the power.
2. If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.
3. If the fuse of indoor unit on PC board is broken,please change it with the type of T. 3.15A/ 250V. If the fuse of outdoor unit is broken,change it with the type of T.25A/250V
4. The wiring method should be in line with the local wiring standard.
5. After installation, the power plug should be easily reached.
6. The waste battery should be disposed properly.
3
Cautions
Safety Instruction
Please read the following Safety Instructions carefully prior to use.
The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.
lnstallation in a inadequate place may cause accidents. Do not install in the following place.
CAUTION
Connect the earth cable.
Do not install in the place where there is any possibility of inflammable gas leakage around the unit.
Do not get the unit exposed to vapor or oil steam.
Check proper installation of the drainage securely
earthing
PROHIBITION PROHIBITION
4
STRICT ENFORCEMENT
Cautions
When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.
WARNING
Use an exclusive power source with a circuit breaker
OFF
Connect power supply cord to the outlet completely
STRICT
ENFORCEMENT
Do not use power supply cord in a bundle.
PROHIBITION
Do not start or stop the operation by disconnecting the power supply cord and so on.
PROHIBITION
STRICT
ENFORCEMENT
Use the proper voltage
STRICT
ENFORCEMENT
Take care not to damage
the power supply cord.
PROHIBITION
Do not channel the air flow directly at people, especially at infants or the aged.
PROHIBITION
Do not use power supply cord
extended or connected in halfway
PROHIBITION
Do not insert objects into the air inlet or outlet.
PROHIBITION
Do not try to repair or reconstruct by yourself.
Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.
PROHIBITION
Do not install the unit near a fireplace or other heating apparatus.
PROHIBITION
Do not place animals or plants in the direct path of the air flow
PROHIBITION
CAUTION
Take fresh air occasionally especially when gas appliance is running at the same time.
STRICT
ENFORCEMENT
Check good condition of the installation stand
PROHIBITION
Do not place any objects on or climb on the unit.
PROHIBITION
Do not operate the switch with wet hand.
PROHIBITION
Do not pour water onto the unit for cleaning
PROHIBITION
Do not place flower vase or water containers on the top of the unit.
PROHIBITION
5
Parts and Functions
Indoor unit
Air Purifying Filter
Outlet
Inlet
Inlet grille
UV light degerming device (inside)
Air filter(inside)
display board(inside)
(inside)
Anion generator
(inside)
Horizontal louver(inside)
(adjust left and right air flow)
Outdoor unit
Vertical flap (adjust up and down air flow. Don't adjust it manually)
1
OUTLET CONNECTING PIPING AND ELECTRICAL WIRING
2
INLET
3
4
DRAIN HOSE
6
Parts and Functions
19
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
33
20
21
22
23
24
25
26
27
26
29
30
31
32
28
8. HOUR button
Used to set clock and timer setting.
9. HEALTH AIRFLOW button
Used to set the health airflow mode.
10. HEALTH button
Used to set healthy operation.
11. ON/OFF button
Used for unit start and stop.
12. TIMER ON display
13. FAN SPEED display
LOW HI
MED AUTO
14. LOCK display
15. SWING UP/DOWN display
16. SLEEP display
17. HEALTH display
18.FRESH AIR display
19. Operation mode display
Operation mode
Remote controller
Display board
AUTO HEAT FANCOOL DRY
1. LOCK
Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition display appears. Press it once again, lock will be canceled and lock condition display disappears.
2.LIGHT button
Control the lightening and extinguishing of the indoor LED display board.
3.CODE
Used to select CODE A or B with a press,A or B will be displayed on LCD. Please select A without special explanation.
4. TIMER button
Used to select TIMER ON, TIMER OFF, TIMER ON-OFF.
5. CLOCK button
Used to set correct time.
6. SLEEP button
Used to select sleep mode.
7. MODE button
AUTO COOL DRY FAN HEAT
20.Singal sending display
21. POWER/SOFT display
22. Left/right air flow display
23. TEMP display
Remote controller: to display the TEMP. setting.
24. TIMER OFF display
25. CLOCK display
26. TEMP button
Used to select your desired temperature.
27. FAN button
Used to select fan speed: LOW,MED, HI, AUTO.
28. SWING UP/DOWN button
Used to select up or down air sending direction.
29. SWING LEFT/RIGHT button
Used to select left/right air flow.
30.
FRESH
button
Use to set fresh air function.
31. SET button
Used to confirm timer and clock settings.
32. POWER/SOFT button
Use to set power/soft function.
33. RESET
When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal.
NOTE: Cooling only unit do not have functions and displays related with heating.
The fresh function is optional.
7
Parts and Functions
Clock Set
When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows:
1. Press CLOCK button,"AM" or "PM" flashes.
2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly.
3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working.
Remote controller's operation
When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.
Don't throw or knock the remoter controller.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated right 2 R-03 (7#) batteries
Remove the battery cover:
Slightly press" "area and push down the cover as illustrated.
Load the battery: Be sure that the loading is in line with the "+" / "-".
request as illustrated on the bottom of the case.
Put on the cover again.
Confirmation indicator:
After pressing power "
Note:
Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.
Used two new same-typed batteries when loading. If the remote controller can't run normally during operation, please remove the batteries and
reload several minutes later.
", if no display, reload the batteries.
Hint:
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key.
8
Operation
HEALTH operation
1.Unit start
Remote controller
TEMP
Press on/off button (" ") on the remote controller, unit starts. Health function includes health anion function, UV light
degerming function.
2.Health anion function
Press HEALTH button. For each press, is displayed.
Air conditioner starts health anion function operation.
For twice press, disappears,the operation stops.
When indoor fan motor is running, it has healthy process function. (It's available under any mode)
When the fan in the indoor unit does not work, the health lamp lights up, but the anion generator does not release anion.
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
BRIEF INTRODUCTION TO HEALTH ANION FUCTION
The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.
About UV light degerming function
UV light emitted by the UV light device of the indoor unit catalytically
2
activates the nano TiO and the degerming effect is highly efficient and lasting. Note: when the function is running, don't open the inlet grille.
on the multi-lights touching intermediary,
9
Operation
Auto Operation
Remote controller
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
SET
1. Unit start
Press on/off button (" ") on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO COOL DRY FAN HEAT
Then
Select Auto operation
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1 rapidly
Every time the button is pressed, temp.setting decrease 1 rapidly
Select a desired temperature.
o
C,if kept depressed, it will increase
o
C,if kept depressed, it will decrease
TIMER
LOCK RESETLIGHT
CODE
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
HI
AUTO
Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
5.Unit stop
Press on/off button (" "), the unit stops.
About Auto Operation Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature.
10
Operation
Cool Operation
Remote controller
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
SET
1. Unit start
Press on/off button (" ") on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO
COOL DRY FAN HEAT
Then Select COOL operation
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1 rapidly
Every time the button is pressed, temp.setting decrease 1 rapidly
Select a desired temperature.
o
C,if kept depressed, it will increase
o
C,if kept depressed, it will decrease
LOCK RESETLIGHT
CODE
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
HI
AUTO
Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
5.Unit stop
Press on/off button (" "), the unit stops.
11
Operation
Dry Operation
Remote controller
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
SET
1. Unit start
Press on/off button (" ") on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
AUTO
COOL DRY FAN HEAT
Then Select DRY operation
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1 rapidly
Every time the button is pressed, temp.setting decrease 1 rapidly
Select a desired temperature.
o
C,if kept depressed, it will increase
o
C,if kept depressed, it will decrease
LOCK RESETLIGHT
COOL operation starts when room temp.is higher than temp.setting.
o
Temp.setting+2 Temp.setting
C
CODE
On reaching temp.setting +2 unit will run in mild DRY mode.
Ultra-low air flow
o
C
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
HI
AUTO
Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp.setting+2
o
C,unit will run intermittently
at LOW speed regardless of FAN setting.
5.Unit stop
Press on/off button (" "), the unit stops.
12
Operation
Fan Operation
Remote controller
1. Unit start
Press on/off button (" ") on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
AUTO
COOL DRY FAN HEAT
Then Select FAN operation
3.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
HI
4.Unit stop
Press on/off button(" "), the unit stops.
About FAN operation
In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled. In FAN mode,SLEEP operation is not available.
13
Operation
Heat Operation
Remote controller
2.Select operation mode
1. Unit start
Press on/off button (" ") on the remote controller, unit starts.
Press MODE button. For each press, operation mode changes as follows:
Remote controller:
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
AUTO
COOL DRY FAN HEAT
Then Select HEAT operation
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting increase 1
o
C,if kept depressed, it will increase
rapidly Every time the button is pressed, temp.setting
decrease 1
o
C,if kept depressed, it will decrease
rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
LOW
MED
HI
Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.
AUTO
5.Unit stop
Press on/off button (" "), the unit stops.
14
Operation
Air Flow Direction Adjustment
1.Status display of air sending
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
Vertical flap
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
(Auto swing)
Horizontal louvers
Pos.1
Pos.2
Pos.3
Pos.4
Pos.5
Pos.6
Pos.7
Pos.8
2.Up and down air flow direction
For each press of button, air flow direction on remote controller displays as follows according to different operation modes:
COOL/DRY/FAN
remote controller:
:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.6
HEAT:
remote controller:
Pos.5 Pos.4 Pos.3 Pos.2 Pos.1 Pos.6
AUTO:
remote controller:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6
The vertical flap will swing according to the above positions
3.Left and right air flow direction
For each press of button, remote controller displays as follows :
remote controller:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
The horizontal louvers will swing according to the above positions. Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position.
15
Operation
Sleep Operation
Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. Operation Mode
1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will become 1 another 1 hours, temp. rises by 1 The unit will run for further 6 hours then stops. Temp. is higher than temp. setting so that room temperature won't be too Iow for your sleep.
Remote Controller
O
C higher than temp. setting. After
O
C further.
SLEEP operation starts SLEEP operation stops
Approx.6hrs
O
Rises 1
C
O
C
Unit stop
1 hr
Temp.setting
1 hr
Rises 1
In COOL, DRY mode
In HEAT mode
2. 1 hours after SLEEP mode starts, temp
O
will become 2
C lower than temp.
setting. After another 1 hours, temp
O
decrease by 2 another 3 hours, temp. rises by 1
C further. After more
O
further. The unit will run for further 3 hours then stops. Temp. is lower than temp. setting so that room temperature won't be too high for your sleep.
C
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
Temp.setting
1 hr
1 hr
SLEEP operation starts
Decreases 2OC
Decreases 2
3 hrs
Unit stop
O
C
3 hrs
Rises 1OC
SLEEP operation stops
In HEAT mode
In AUTO mode
3.
The unit operates in corresponding sleep mode adapted to the automatically selected operation mode.
4. In FAN mode
It has no SLEEP function.
5.Set the wind speed change when sleeping If the wind speed is high or middle before
setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change.
16
Operation
Timer On/Off Operation
Set clock correctly before starting TIMER operation.
Remote Controller
1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD.
2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:
Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash.
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
3.Time setting
Press HOUR button. Every time the button is pressed, time setting increases 1 min, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases 1 min, if kept depressed, it will decrease rapidly. It can be adjusted within 24 hours.
4.Confirming your setting
After setting correct time, press SET button to confirm " "or" "on the remote controller stops flashing. Time displayed: Unit starts or stops at x hour x min. (TIMER ON or TIMER OFF).
5.Cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one.
17
Operation
Timer On-Off Operation
Set clock correctly before starting TIMER operation.
Remote Controller
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
SET
1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD.
2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller:
Then select your desired TIMER mode (TIMER ON - OFF). " "will flash.
3.Time setting
Press HOUR button. Every time the button is pressed, time setting increases 1 min, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases 1 min, if kept depressed, it will decrease rapidly. It can be adjusted within 24 hours.
4.Timer confirming for TIMER ON
After setting correct time, press TIMER button to confirm " " on the remote controller stops flashing. " " starts flashing. Time displayed: Unit starts or stops at x hour x min.
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
LOCK RESETLIGHT
CODE
5.Time setting for TIMER OFF
Just press HOUR button ,follow the same procedure in "Time setting for TIMER ON"
6.Time confirming for TIMER OFF
After time setting,press SET button to confirm. " " on the remote controller stops blinking. Time displayed:Unit stops at x hour x min.
To cancel TIMER mode
Just press TIMER button several times until TIMER de disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved.
18
Operation
POWER/SOFT Operation
POWER Operation
When you need rapid heating or cooling, you can use this function.
Remote controller
Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed,display
changes as follows:
Stop the display at
In POWER operation status:
In HEAT or COOL mode, compressor runs in high frequency for 15 min then returns to original status setting.
POWER
BLANK
SOFT
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
To cancel POWER operation
Press POWER/SOFT button twice ,POWER/SOFT disappears.
SOFT Operation
You can use this function when silence is needed for rest or reading.
Selecting of SOFT operation
Press POWER/SOFT button. Every time the button is pressed,display
changes as follows:
POWER
Stop the display at
In SOFT operation mode, fan speed automatically takes"ultra-low"
SOFT
To cancel SOFT operation
Press POWER/SOFT button twice ,POWER/SOFT disappears.
BLANK
Hints: During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm.
19
Operation
Health airflow Operation
Remote controller
TEMP
HEALTH FAN
SWING
H.AIR.
MODE
FRESHSLEEP
CLOCK
TIMER
LOCK RESETLIGHT
SET
CODE
1.Press ON/OFF button (" ") to starting
The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions.
2.The setting of health airflow function
1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air condit­ioner are closed and the airflow is blown horizontally from the above inlet and outlet grills. Avoid the strong airflow blows direct to the body.
2).Press the button of health airflow again, appears on the display. The above inlet and outlet grills of the air cond­itioner are closed and the airflow is blown vertically from the nether inlet and outlet grills. Avoid the strong airflow blows direct to the body.
3.The cancel of the health airflow function
Press the button of health airflow again, both the inlet and outlet grills of the air conditioner are opened, and the unit goes on working under the condition before the setting of health airflow function. After stopping, the outlet grille will close automatically. Notice: Cannot pull direct the outlet grille by hand. Otherwise, the grille will run incorrectly. If the grille is not run correctly, stop for a minute and then start, adjusting by remote controller.
Note: 1 .After setting the health airflow function, the position of inlet and outlet grills is fixed.
2.In heating, it is better to select the mode.
3.In cooling, it is better to select the mode.
4.In cooling and dry, using the air conditioner for a long time under the high air humidity, a phenomenon falling drips of water occurs at the outlet grille .
5.Select the appropriate fan direction according to the actual conditions.
20
Operation
Emergency and Test Operation
Emergency operation:
Use this operation only when the remote controller is defective or lost.
When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation.
In this operation, the system automatically selects the operation modes, cooling or heating, according to the room temperature.
Temperature
ABOVE 21
BELOW 21
Operation mode
O
COOLING
C
O
C
HEATING
Designated temperature
O
24
C
O
24
C
Timer mode
NO
NO
Air flow
AUTOMATIC
AUTOMATIC
It is not possible to operate in dry mode.
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room temperature is below 16 operation.
Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi".
After 30 minutes, test operation ends automatically.
O
C, do not use it in the normal
Removal of the restriction of emergency or test operation
Press the emergency operation switch once more, or manipulate through the remote controller; the "Pi" sound, the emergency or test operation is terminated.
When the remote controller is manipulated, it gets the system back to the normal operation mode.
21
Maintenance
For Smart Use of The Air Conditioner
Setting of proper room temperature
Proper
2TQRGT
temperature
VGORGTCVWTG
Close doors and windows
%NQUGFQQTUCPFYKPFQYU FW
during operation
TKPIQRGTCVKQP
Do not block the air inlet or outlet
Use the timer effectively
7UGVJGVKOGTGHHGEVKXGN[
During cooling operation
&WTKPIEQQNKPIQRGTCVKQP
prevent the penetration of
RTGXGPVVJGRGPGVTCVKQPQH
direct sunlight with
FKTGEVUWPNKIJVYKVJ
curtain or blind
EWTVCKPQTDNKPF
If the unit is not to be used
+HVJGWPKVKUPQVVQDGWUGF
for a long time, turn off the
HQTCNQPIVKOGVWTPQHHVJG
power supply main switch.
RQYGTUWRRN[OCKPUYKVEJ
OFF
Use the louvers effectively
7UGVJGNQWXGTUGHHGEVKXGN[
22
Maintenance
For Smart Use of The Air Conditioner
WARNING
Before maintenance,be sure to turn off the system and the circuit breaker.
Remote Controller
Do not use water, wipe the controller with a dry cloth.Do not use glass cleaner or chemical cloth.
Do not use the following for cleaning
Gasoline,benzine, thinner or cleanser may damage the coating of the unit.
Indoor Body
Wipe the air conditioner by using a soft and dry cloth.For serious stains,use a neutral detergent diluted with water.Wring the water out of the cloth before wiping.then wipe off the detergent completely.
O
Hot water over 40 discoloring or deformation.
C(104OF) may cause
Air Filter cleaning
Open the inlet grille by pulling it upward.
Remove the filter.
Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward.
Clean the filter.
Use a vacuum cleaner to remove dust, or wash the filter with water.After washing, dry the filter completely in the shade.
Attach the filter.
Attach the filter correctly so that the "FRONT" indication is facing to the front.Make sure that the filter is completely fixed behind the stopper.If the right and left filters are not attached correctly, that may cause defects.
Close the inlet grille.
23
Once every two weeks
Maintenance
Replancement of Air Purifying Filter
1.Open the lnlet Grille
Open the inlet grille by pushing each ends of the inlet grille upward.(use thumbs to push up)
2.Detach the standard air filter
Slide the knob slightly upward to release the filter, then withdraw it.
3.Attach old Air Purifying Filter
Put air purifying filter appliances into the right and left filter frames.
Detach old Air Purifying Filter
The green aspect of the bacteria-killing medium
4.Attach the standard air filter
(Necessary installation)
5.Close the Inlet Grille
Close the Grille surely
air purifying filter will face outside, the white aspect will face to the machine.
Note: the bacteria-killing mediums placed on the right side. the multi-lights touching intermediary is placed on the left side.
Common sense:
1.For the units with UV light degerming function,the air purifying filter of the bacteria-killing medium and the multi-lights touching intermediary is effective for a long time and don't need to be changed (UV light emitted by the UV light device of the indoor unit catalytically activates the nano TiO efficient and lasting. multi-lights touching intermediary don't need to be exposed to the sunlight.).
2.For the units without UV light degerming function,the air purifying filter of the multi-lights touching intermediary will be solarized in fixed time. In normal family,it will be solarized every 6 months. The solarization time will last no less than 8 hours under the state of abundant sun.
3.But in the use, please note to clean the filter frequently (take off the back suction cleaner or lightly pat it) to avoid the operating effect is lowered due to the dust covering the filter. Multi-lights touching intermediary and bacteria-killing medium filter is strictly prohibited from being cleaned by water.
The the bacteria-killing medium filter not in use should be stored in shade, cool and dry place. Please don't expose it to the sunlight for a long time otherwise the degerming performance will drop.
on the multi-lights touching intermediary, and the degerming effect is highly
2
24
Maintenance
To Keep Your Air conditioner in Good Condition after Season.
Operate in cooling mode for 2-3 hours.
To prevent breeding mold or bad smell, be sure to
O
operate at the designated temperature or 30 mode and High speed fan mode for 2-3 hours.
Put off the power supply cord.
C,cooling
Cleaning the body.
Take out the batteries from the wireless remote controller.
25
Maintenance
Before Setting in High season
Cleaning the standard air filter.
Operation without filter may cause troubles.Be sure to attach both right and left filters prior to the operation. Each of them are of different shapes.
Connecting the earthing cable.
Caution
Incomplete earthing may cause an electric shock.
Do not block the air inlet or outlet.
Plug-in
Caution
After brush away dust at the plug, insert the plug of the power supply cord into the outlet completely.In case of suing exclusive circuit breaker,switch on the circuit breaker.
EARTHING
NO WET HAND
26
6TQWDNGUJQQVKPI
$GHQTGCUMKPIHQTUGTXKEGEJGEMVJGHQNNQYKPIHKTUV
0QTOCN 2GTHQTOCPEG KPURGEVKQP
2JGPQOGPQP
6JGU[UVGOFQGUPQVTGUVCTV KOOGFKCVGN[
0QKUGKUJGCTF
5OGNNUCTGIGPGTCVGF
%CWUGQTEJGEMRQKPVU
9JGPWPKVKUUVQRRGFKVYQPVTGUVCTV KOOGFKCVGN[WPVKNOKPWVGUJCXGGNCRUGF VQRTQVGEVVJGU[UVGO 9JGPVJGGNGEVTKERNWIKURWNNGFQWVCPF TGKPUGTVGFVJGRTQVGEVKQPEKTEWKVYKNNYQTM HQTOKPWVGUVQRTQVGEVVJGCKTEQPFKVKQPGT
&WTKPIWPKVQRGTCVKQPQTCVUVQRCUYKUJKPI QTIWTINKPIPQKUGOC[DGJGCTF#VHKTUV OKPWVGUCHVGTWPKVUVCTVVJKUPQKUGKUOQTG PQVKEGCDNG6JKUPQKUGKUIGPGTCVGFD[ TGHTKIGTCPVHNQYKPIKPVJGU[UVGO &WTKPIWPKVQRGTCVKQPCETCEMKPIPQKUGOC[ DGJGCTF6JKUPQKUGKUIGPGTCVGFD[VJG ECUKPIGZRCPFKPIQTUJTKPMKPIDGECWUGQH VGORGTCVWTGEJCPIGU 5JQWNFVJGTGDGCDKIPQKUGHTQOCKTHNQYKP WPKVQRGTCVKQPCKTHKNVGTOC[DGVQQFKTV[
6JKUKUDGECWUGVJGU[UVGOEKTEWNCVGUUOGNNU HTQOVJGKPVGTKQTCKTUWEJCUVJGUOGNNQH HWTPKVWTGEKICTGVVGU
/WNVKRNG EJGEM
/KUVQTUVGCOCTG
&QGUPQVYQTMCVCNN
2QQTEQQNKPI
DNQYPQWV
&WTKPI%11.QT&4;QRGTCVKQPKPFQQTWPKV OC[DNQYQWVOKUV6JKUKUFWGVQVJGUWFFGP EQQNKPIQHKPFQQTCKT
+URQYGTRNWIKPUGTVGF! +UVJGTGCRQYGTHCKNWTG! +UHWUGDNQYPQWV!
+UVJGCKTHKNVGTFKTV[!0QTOCNN[KVUJQWNFDG ENGCPGFGXGT[FC[U #TGVJGTGCP[QDUVCENGUDGHQTGKPNGVCPFQWVNGV! +UVGORGTCVWTGUGVEQTTGEVN[! #TGVJGTGUQOGFQQTUQTYKPFQYUNGHVQRGP! +UVJGTGCP[FKTGEVUWPNKIJVVJTQWIJVJG YKPFQYFWTKPIVJGEQQNKPIQRGTCVKQP!7UG EWTVCKP #TGVJGTGVQQOWEJJGCVUQWTEGUQTVQQOCP[ RGQRNGKPVJGTQQOFWTKPIEQQNKPIQRGTCVKQP!
27
Índice
Precauciones para el uso Denominación de los componentes Teclas y display del mando a distancia Funcionamiento Mantenimiento Guía para la búsqueda de las averías
2
9 1
3 3
2 4
3
5
4 4
9
28
Loading...
+ 65 hidden pages