Haier 29T7A User Manual

0090505084
29T7A
Colour Television
Operation Instructions
MAIN FUNCTION
218 Programmes stored
Dynamic noise reduction
Multi-picture mode, multi-sound mode selection
Auto-correcting black balance
CONTENTS
WARNING AND CAUTIONS
BASIC FEATURE
TECHNICAL SPECIFICATION
FUNCTION BUTTONS AND EXTERNAL SOCKETS
REMOTE CONTROLLER BOARD
OPERATING MENU
MULTI FUNCTION TIMER
GENERAL OPERATION
TELETEXT FUNCTION
EXTERNAL CONNECTIONS
AV SIDE PANEL CONNECTION DIAGRAM
1
2
2
3
5
6
10
12
14
15
16
TROUBLESHOOTING GUIDE
17
WARNING AND CAUTIONS
BASIC FEATURE
1. When you clean the TV set, please pull out the power plug from AC outlet. Or may result in electric shock, fire or damage to the TV set. Don't clean the cabinet and the screen with benzene, petrol and other chemicals.
2. In order to prolong the using life of the TV set, please place it in a well ventilated location.
3. Don't place the TV set in direct sunlight or near heat source.
4. Do not place the TV set near rain or moisture as it may cause an electric shock, or the TV set to catch fire. The TV set must only be used in dry indoor Location.
5. The back cover must only be removed by a registered electrical service person. Removing the back cover may result in electric shock, fire or damage to the TV set.
6. If the TV set is not going to be used for long time, or there is a severe thunder & lightening storm, it is recommended that the TV set be disconnected from the AC power outlet and the aerial plug removed.
218 programs stored
Auto-correcting black balance
Surround stereo
Blue extension,Green improvement
Multi-picture modes and multi-audio modes
Fast teletext
Audio/Video input, S-Video input
DVD component input
TECHNICAL SPECIFICATION
POWER SUPPLY: See rating plate TV SYSTEM: B/G D/K COLOUR SYSTEM: PAL SECAM NTSC3.58/4.43 (AV) CRT: 29" AERIAL INPUT IMPEDANCE: 75Ω unbalanced VIDEO INPUT: 1.0VP-P(75Ω) AUDIO INPUT: 436mVrms(40KΩ) VIDEO OUTPUT: 1.0VP-P(75Ω) AUDIO OUTPUT: 436mVrms(600Ω) AUDIO MAX OUTPUT POWER: 5W+5W POWER CONSUMPTION: See rating plate NET WEIGHT(kg): 44 NET SIZE(mm): 827×505×582
Explanation on the display tube
Should the picture tube require cleaning, disconnect the power and use a dry soft cotton cloth. Do not use any cleaner or abrasive cloth.
1
Supplied accessories: Infrared remote control handset 1 Battery(AA) 2 Operating instructions 1 Design and specifications are subject to change without notice.
2
FUNCTION BUTTONS AND EXTERNAL SOCKETS
FUNCTION BUTTONS AND EXTERNAL SOCKETS
Antenna
Y
Cr
Cb
S-VIDEO
OUT
IN
L AUDIO R
VIDEO
Figure A Figure B
75-300Ω
Antenna adapter
Figure C
Antenna cable with a plug
Antenna feeder
Figure D
Coaxial cable(75Ω) twin-lead cable(300Ω)
1.Front Panel
Antenna Connection
Connect an antenna to the antenna socket on the TV set, we recommend using a Cable TV system for better picture and audio quality.
1.If you use a coaxial cable(75 ),insert the antenna plug (see figure C) into 75 socket
Ω
Ω
MENU
TV/AV
VOL-
VOL+
CH-
(see figure A).
2.If you use a twin-lead cable(300 ),please
Ω
shape the cable as figure D, and connect the leads to antenna adapter and then insert the antenna adapter into the 75 socke (see
Ω
figure B).
Power source wire connection Insert the power plug into AC outlet. To install and to replace batteries of the remote control unit
1.Place the remote control unit with the face down, then open the battery cover of the unit.
2.Place the two"AA"size batteries, matching the + and - signs on each battery to the + and -signs of the battery compartment.
3.Close the cover of the battery compartment. NOTE: (1)Don't drop or wet or dismantle the unit.
(1)Remote sensor: let the remote controller aim here the set can receive remote control signal.
(3)Power indicator: the indicator lights in standby status ,the indicator lights in
sleep status . The indicator glints when
you use remote controller.
(2)If you don't intend to use the unit for a long period or the electricity of the batteries is used up, remove the batteries to prevent batteries acid from leaking into
2.Rear Panel and Side Panel
the battery compartment. (3)Always replace both batteries at the same time. (4)Do not use rechargeable batteries (Ni-cd) or mix battery types. (5)Never place batteries in a fire. Dispose of the batteries with your domestic rubbish collection.
(10)
(8)S-video input (9)Video input/output (10)DVD component input (11)Antenna input (12)Audio input/output
OUT
IN
(9)
3 4
(4) (7) (6)
(5)
CH+
(3) (1) (2)
(2)Power switch: press the button to turn
on the TV set . Press the button again
to turn off the TV set.
(4)Menu button (5)Program up/down button (6)Volume up/down button
(7)TV/AV
VIDEO
VIDEO
L
AUDIO-L
AUDIO
AUDIO-R
R
Y
Cr
Cb
S-VIDEO
OUT
IN
L AUDIO R
VIDEO
Y
Cr
Cb
S-VIDEO
(11)
L AUDIO R
VIDEO
(12)
(8)
REMOTE CONTROLLER BOARD
OPERATION MENU
FUNCTION DESCRIPTION
N
PROGRAM SCAN STANDBY
SWAP PROGRAM BETWEEN THE PRESENT AND THE LAST
MUTE
T
E
O
M
Z
O
OM
D
I
L
S
L
P
L
A
Y
TV/VIDEO SELECTION VOLUME CONTROL CHANNEL NUMBER UP/DOWN PICTURE MENU SOUND MENU TIME MENU
FUNCTION MENU
ONE DIGIT SELECTION ONE OR TWO OR THREE DIGITS PRE-SELECTION MENU DISPLAY
EXIT MENU DISPLAY
I
T
INVALID BUTTON
I
I
PICTURE MODE SELECTION
TD
T
D
SOUND MODE SELECTION
TUNE MENU SELECTION
E
P
I R
MU
T
1
4
7
-/-
-
.
ST
C
T
U
U TI
O
S
MARK
S A
S
C
AN
E
S
W P
A
Z
3
6
9
I
- I
C
H
+
PP
.
M
E
NU
C H
-
N
F TU
OOM
CLAL
EI
X
T
T
V
I
/
AV
S
.SD
T
V +
O
L
E
N
O
TI N
C
2
5
8
0
DP
V
O
L
-
E
E U
M
D
N
C
SWAP
M
U
Z
O
C
A
TV/AV
-VOL+
-CH+
PICTURE
SOUND TIME
FUNCTION
0-9
-/--
?
MENU
E
X
I-
P
S.
S
.
S
N
TU
TELETEXT SUBTITLE
TV/TELETEXT ENTERING/EXITING
??
TO REVEAL CONCEALED TELETEXT TELETEXT ZOOM TELETEXT PAGE HOLD
TELETEXT/TV MIX MODE TV/TELETEXT ALTERATION
TIME DISPLAY(IN TV MODE)/SUBCODE SWITCH
EAST/WEST
NOTE The function of selecting menu button on the remote controller is the same as that of program up/down button on the TV set. The function of identifying menu button on the remote controller is the same as that of volume up/down button on the TV set.
Setting channel
1.Entering and exiting menu Press MENU button on the remote controller once (or directly press PICTURE button on the remote controller), PICTURE menu displays on the screen; press MENU button twice (or directly press SOUND button on the remote controller), SOUND menu displays on the screen . Press the menu button again (3 times, or directly press TIME button on the remote controller), TIME menu displays
TUNE COLOUR AUTO SOUND B/G BAND VHFL SKIP OFF PROGRAM 19 SEARCH FINE TUNE AUTO SEARCH
on the screen. Press the menu button again (4 times, or directly press FUNCTION button on the remote controller), FUNCTION menu displays on the screen. Press the menu button again (5 times or directly press TUNE button on the remote controller), TUNE menu displays on the screen. Press the menu button again (6 times), EXCHANGE menu displays on the screen .To turn off the on-screen menu display, either press the EXIT button or allow the TV set to automatically turn off the menu by not pressing any buttons for a few seconds.
2.Auto search A. Press MENU button five times continually (or directly press TUNE button on the remote controller), e
nsure that the TUNE menu is displayed. Press the CH+/- buttons to select AUTO SEARCH. Then press the VOL+button, the TV set will begin to search programs from present programme No.. B. After the search has finished, the TV set will return to the first program stored.
3. Search Press MENU button five times continually (or directly press TUNE button), ensure that the TUNE menu is displayed. Press the CH+/- buttons to select SEARCH. Then press the VOL+ button to search up or V- button to search down to the next TV station.(It is much faster to search up.)If the wrong station is found ,press the search button again. You may need to repeat this until the correct station is located. To store the new program, press the EXIT button.
4.Fine tune If the picture or sound is poor, try to use the "FINE TUNE" feature. Select the FINE TUNE by using the CH +/- buttons. Use the VOL +/- buttons to fine-tune the sound and picture for optimum results. Then press the EXIT button to store the results. Do not use this feature unless reception is poor.
5.Selecting the sound system Press the CH+/- buttons to select SOUND item. Then press the VOL+/- buttons to select a sound system you need.
6.Selecting color system Usually this should be set in the auto position. However if the colours displayed on the screen are incorrect you can manually select the correct colour system. When you have finished remember to turn it back to auto again so that other programs will still work correctly. Use the CH+/- buttons to select COLOUR then press VOL+/­ buttons to select a color system you need. Press the EXIT button to save the setting.
5
6
OPERATION MENU
7.Program skip The Program skip feature enables you to skip/hide programs that you do not wish to be displayed when using the CH+/- buttons. These channels will still be displayed by directly using the channel number buttons on the remote controller. To skip, press the CH+/- buttons to select the SKIP menu, press the VOL+/- buttons to tune the skip feature on/off. Press the EXIT button to save the setting.
8. Program number The program number is the remote controller channel number. You can change the program number to see channels stored without exiting this main menu. Press the CH+/- buttons to select PROGRAM, press the VOL+/- buttons to change the program number that you are adjusting.
9. Band switching (Note: This is a new item.) If you already know what band the channel is on, tuning can speed up by selecting the correct band before going into the search menu. This feature should only be used if you understand the channels in your local area.
Picture Adjustments
Press the MENU button once or press the PICTURE button on the remote controller to display the PICTURE setting menu.
1.Contrast (adds depth to the picture) Press the CH+/- buttons to select CONTRAST, then press the VOL+/- buttons to adjust the contrast level.
2. Brightness (adds sparkle and shine to the picture) Press the CH+/- buttons to select BRIGHTNESS, then press the VOL+/- buttons to adjust the brightness level.
3. Colour (adds colour depth) Press the CH+/- buttons to select COLOUR, then press the VOL+/- buttons to adjust the colour level.
4. Sharpness (adds fine detail) Press the CH+/- buttons to select SHARPNESS, then press the VOL+/- buttons to adjust the sharpness level. Note: Do not turn the sharpness up to high if the reception is poor or has lots of noise as it will enhance the fine grain details.
5. Black stretch (adds deeper blacks and increases the contrast range) Press the CH+/- buttons to select BLACK STRETCH, then press the VOL+/- buttons to turn this feature on/off.
6.Hue Press the CH+/- buttons to select HUE, then press the VOL+/-buttons to adjust the hue level. Note: Hue is only used in the AV mode.
7
PICTURE CONTRAST 89 BRIGHTNESS 66 COLOUR 50 SHARPNESS 50 BLACK STRETCH OFF
IIIIIIIIIIIIIIIIIIIIIIIII..........
OPERATION MENU
Sound Adjustments
Press the MENU button twice or press the SOUND button on the remote controller to display the sound setting menu.
1 .Volume (adjust the loudness level)
SOUND VOLUME 50 BASS 50 TREBLE 50 BALANCE 0 SURROUND OFF
IIIIIIIIIIIIIIIIIIIIIIIII..........
Press the CH+/- buttons to select VOLUME, then press the VOL+/- buttons to adjust the volume level.
2.Bass (add low frequency depth) Press the CH+/- buttons to select BASS, then press the VOL+/- buttons to adjust the bass level.
3.Treble (add high frequency clarity) Press the CH+/- buttons to select TREBLE, then press the VOL+/- buttons to adjust the treble level.
4.Balance (selects between the left and right stereo channel levels) Press the CH+/- buttons to select BALANCE, then press the VOL+/- buttons to adjust the balance level.
5.Surround (enhances the stereo effect by making the sound appear wider) Press the CH+/- buttons to select SURROUND, then press the VOL+/- buttons to turn this feature on/off.
8
OPERATION MENU
MULTI FUNCTION TIMER
Function Menu
1.Language selection Press the CH+/-buttons to select LANGUAGE, then press the VOL+/-buttons to select an OSD language you need.
2.Background (If the signal is very poor or there is no input signal the picture will mute to black.)
FUNCTION ENGLISH BACKGROUND ON NOISE REDUCE OFF FADE ON CHILD LOCK OFF AVL OFF CALENDAR
Press the CH+/- buttons to select BACKGROUND, then press the VOL+/- buttons to turn this feature on/off.
3.Noise reduce (Picture Noise & Grain reduction circuit) Press the CH+/- buttons to select NOISE REDUCE, then press the VOL+/- buttons to turn this feature on/off.
4.Fade The FADE control allows time for the picture tube to warm up and gently turned on, which can help prolong the life of the picture tube.
5.Child lock (enables the TV front control buttons to be locked) Press the CH+/- buttons to select CHILD LOCK, then press the VOL+/­ buttons to turn this feature on/off.
6.AVL (Automatic Volume Limit control reduces effect of large volume changes such as when the ads come on.) Press the CH+/- buttons to select AVL, then press the VOL+/- buttons to turn this feature on/off.
7.Calendar (enables the TV sets internal calendar to be set) Press the CH+/- buttons to select CALENDAR, then press the VOL+/- buttons to select the item to be changed and the CH+/- buttons to alter each setting.
Multi Function Timer
The TV set has built a comprehensive timer that there are five basic functions.
1.Clock
2.On time so that the TV set can be programmed to turn on at a certain time.
3.Off time to allow the TV set to turn off at a preset time.
4.Sleep timer to allow the TV set to turn off after
TIME
CLOCK --:--
ON TIME --:--
ON-PROG 1
OFF TIME --:--
SLEEP TIMER --:--
REMIND TIME --:--
REMIND PROG 1
10 ~ 180 minutes.
5.Program remind timer, that displays an on­ screen reminder prompt, when a program on a different channel is due to start.
Note: The clock will only work in the TV set if left turned on or in standby. When the set is disconnected from the power supply or is turned off by the main power switch on the front panel, the clock looses power and will need to be reset when the power is reconnected.
Selecting the clock menu Press the MENU button four times until the CLOCK menu is displayed or press the yellow time button on the remote controller.
1. Clock (master timer clock) Press the CH+/- buttons to select CLOCK, then press the VOL+/- buttons to adjust the hour. Press the CH- buttons to select minute and the VOL +/- buttons to adjust the minute.
2. On Time Press the CH+/- buttons to select ON TIME, then press the VOL+/- buttons to adjust the hour. Press the CH- button to select minutes and the VOL+/- buttons to adjust the minutes. Press the CH- button to select ON-PROG and the VOL+/­ buttons to select the TV channel that the TV set will automatically turn on to.
3. Off Time Press the CH+/- buttons to select OFF TIME, then press the VOL+/- buttons to adjust the hour. Press the CH- button to select minute and the VOL+/- buttons to adjust the minute.
4. Sleep Timer Press the CH+/- buttons to select SLEEP TIMER, then press the VOL+ button
9
10
MULTI FUNCTION TIMER
GENERAL OPERATION
to adjust the amount of time before the TV set will automatically turn off. Each time the VOL+ button is pressed the sleep time will increase by 10 minutes. The maximum sleep time is 180 minutes.
5. Remind Time Press the CH+/- buttons to select REMIND TIME, then press the VOL+/- buttons to adjust the hour. Press the CH- button to select minute and the VOL +/- buttons to adjust the minute. Press the CH- button to select REMIND PROG and the VOL +/- buttons to select the TV channel that the TV set will automatically remind you to turn to while watching another channel.
Program Number Exchange
This feature enables TV programs that may be on a wrong TV channel number to be swapped/exchanged. This feature is very useful when Automatic Search Tuning has been used, to reallocate the found programs to the correct channel numbers.
Press the MENU button 6 times until the exchange menu is displayed. Press the CH+/- buttons until program 1 is selected. Use the VOL+/- buttons to select the channel number to be swapped. (I.E If you wish to exchange channel 2 and 4 PROGRAM 1 should = 2.) Press the CH+/- buttons until program 2 is selected. Use the VOL+/- buttons to select the channel number to be swapped. (I.E If you wish to exchange channel 2 and 4 PROGRAM 2 should = 4.) Press the CH+/- buttons until EXCHANGE is selected. Press the VOL+ button to enable the exchange.
EXCHANGE PROGRAM 1 1 PROGRAM 2 1 EXCHANGE
1.Channel Changing (218 possible channels) Use either the CH+/- buttons on the remote controller or the front panel of the TV set to change the channels. Or directly enter the channel number with the numeric button on the remote controller. To select channel numbers from 10 ~ 99, press [-/--] button and enter the two digits channel number. To select channel numbers from 100 ~ 218, press [-/--] button and enter the 3 digits channel number.
2.Volume Adjustment Press the VOL+/- buttons on the remote controller or the front of the TV set to adjust the volume level. The range is 0~100. When the volume buttons are pressed, the volume level is displayed automatically on the TV screen.
3.Standby Using the remote controller the TV set can be placed into standby mode. Standby mode must be used when the timer features is operated correctly. A red standby light will glow on the TV front panel when the TV set is placed into standby. To turn the TV set back on again, press standby button on the remote controller again. It will take a few seconds before a picture will be displayed.
4.Mute Press the MUTE button on the remote controller to mute the TV set sound. Pressing the MUTE button again will turn the sound back on again.
5.Preset Picture Modes Our engineers have designed in 5 commonly used picture settings to allow fast picture level selection depending on what type of TV program is showing. Each mode is selected in turn by pressing the "P. STD" button on the remote controller. The 5 modes are: Listen- This is a new feature that blacks out the TV screen when listening to music only channels. Soft - Designed for night time low light viewing. Standard - Designed for rooms that have good all round lighting. Rich - Designed for rooms with high ambient lighting such as daytime sport. User- A spare setting that can be adjusted to personal tastes.
All the 5 modes can be independently adjusted by using the PICTURE adjustment menu.
11
12
GENERAL OPERATION
TELETEXT FUNCTION (FAST TEXT)
6.Preset Sound Modes Our engineers have designed in 4 commonly used sound modes to allow the best possible sound to be selected quickly. Each mode is selected in turn by pressing the "S.STD" button on the remote controller. The 4 modes are: Speech- Designed to reduce the bass and treble which enhances the voice for news programs. Theatre- Enables extra bass and treble to enhance the movie experience. Music- Adjust the sound to best suit music programs. User - A spare setting that can be adjust to personal tastes. All the 5 modes can be independently adjusted by using the PICTURE adjustment menu.
7.Recall (on-screen display) The CALL button on the remote controller allows the on-screen menu to be displayed, showing the channel numbers and colour system and sound system.
8.Program Scan (Automatically increments/scans the channels and displays each channel for a short time.)The SCAN button on the remote controller turns on/off the scan feature.
9.Zoom (changes the picture size format) Each time the ZOOM button is pressed, the picture size will change. There are 3 size options: Normal - Used for standard 4:3 picture programs. 16:9 - Automatically reduces the height so that the TV set displays wide screen type image. Enlarge - Zooms the picture in to magnify smaller images.
10.Channel Swap (toggles between the last channel view and the current channel) Each time the SWAP button is pressed, the last channel view is displayed.
11. AV Input Selection Each time the TV/AV button is pressed, the input selection will cycle among TV- AV1- AV2- SVHS- DVD- TV. Notes: I.AV1 & SVHS share the same AV1 audio input. .In AV modes the RECALL status display will only display the colour system.
1.TV/Teletext Button (Turns the Teletext feature On/Off) [ ] Press the [ ] button on the remote controller to turn teletext On/Off. To select a teletext page either directly enter the page number using the numeric key pad on the remote control or use the CH+/- buttons, or the coloured Fast Text buttons.
2.Mix Mode [ ] While in Teletext mode press the [ ] and will show the teletext data superimposed on top of the TV picture. Press the button again to revert back to Full text.
3.Cancel Mode [ ] This feature allows the TV picture to be displayed while next page to be searched is entered and found. Only the top teletext line is displayed until the page is found. Press the [ ] button to hide the teletext information. Either press the [ ] (Cancel button) or the [ ] (Text button) to exit the cancel display mode.
4.Language Mode [ ] Pressing the [ ] button will change the Teletext characters between Eastern and Western.
5.Hold [ ]
Pressing the [ ] button will stop the teletext page automatically updating. This feature is very useful where there are several teletext pages on the same page number.
6.Size [ ]
Pressing the [ ] button changes between full screen top half bott om a nd half full screen. This featur e is v ery useful as it magnifies the image making the characters easier to read.
7.Reveal [ ]
Pressing the [ ] button will reveal hidden text. This feature is used to reveal information such as answers to teletext on-line inte ractive puzzles.
8.Subtitle [ ]
Pressing the [ ] button will get the teletext decoder to automa ti cally search for the subtitle page.
?
?
13
9.Time [ ]
While in normal TV mode only, press in g the [ ] button will display the teletext time in the top right hand corner for a few seconds. In telete xt mode, the button can be used as sub-code switch.
14
TELETEXT FUNCTION (FAST TEXT)
10.Fast text coloured buttons Fast text automatically display s the four most commonly used pages that the broadcaster thinks that you may w ant to choose next. Press the same coloured button on the remote as the colour ed link at the bottom of the teletext page to go directly to that page.
EXTERNAL CONNECTIONS
Y
Cr
Cb
S-VIDEO
OUT
IN
L AUDIO R
VIDEO
VIDEO
AUDIO
VIDEO
L
AUDIO-L
AUDIO-R
R
15
VCR (without S-VIDEO terminal)
W R
Y
Y
Cb
OUT
IN
VIDEO
L AUDIO R
VCR (with S-VIDEO terminal)
T U
UTP O
W R
O E D
-VI S
PU T
E OU D O TT
I V
O
TO
16
S-VIDEO
Cr
G
DVD(with DVD component)
T O O
A UD
R
W
I
OU
T P U T
T c o t
o m
p o n e
B
R
n o u
t
TROUBLESHOOTING GUIDE
To assist in location possible faults use help guide below
BREAKDOWN PHENOMENON
PICTURE
Picture with snow
Double or Triple Image
Disturb
Normal
No Picture
SOUND
Noise
Normal
Noise
No Sound
No Sound
The aerial direction and connection
This is called ghosting which can be minimized with an outside aerial, and good quality cable and terminations. Altering the aerial direction can also minimize this effect.
Electrical interference which can be caused by cars, motorbikes etc, Fluorescent lamps and dirty insulators on overhead power cables.
VolumeSound mute
Ensure that the power supply is connected to the TV set and turned on. Also ensure that the TV set is not in "Listen Mode" or that the brightness and contrast are not turned down.
CHECKING
Adjust color control
No Color
Normal Volume
Adjust channel again
Scramble
Color Spot
Note:
1.If the fault can not be repaired using the above guide consult with your local authorized service center.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to remove the back cover as the TV set has dangerous voltages in side that may cause a fatality or fire.
3. The cabinet may produce the occasional "snapping sound" This is normal and caused by the materials in the cabinet expanding with room temperature changes.
Normal or Weak Volume
Normal Volume
Colour Purity fault which can be caused by moving the TV set, placing magnets near the TV screen or turning on/off house hold appliances such as vacuum cleaners near the TV set. Turn the TV off with the mains power switch for 15 minutes. When the power is turn on again the TV set will automatically degauss the picture. In server cases leave
the TV set turned off over night.
17
Loading...