Haier 25FV6 User Manual

25FV625FV6
COLOUR TELEVISION
OPERATING
INSTRUCTIONS
Stage curtain for open and close effect
Digital I C bus control
Auto search tuning & 218 programs stored
Multi-picture modes selection
Multi-function timer, appointing program
2
CONTENTS
Warning and cautions.............................................................................................1
Basic feature...........................................................................................................2
Technical specification...........................................................................................2
Preparing for operations.........................................................................................3
Function buttons and external sockets....................................................................4
AV connection.........................................................................................................5
Remote controller guide..........................................................................................6
Power supply...........................................................................................................7
Tuning procedure....................................................................................................7
Picture adjustment...................................................................................................9
Other functions......................................................................................................10
Multifunction timer...............................................................................................14
Lock function.........................................................................................................15
Trouble shooting guide..........................................................................................17
WARNING AND CAUTIONS
BASIC FEATURE
1. When you clean the TV set, please pull out the power plug from AC outlet. Or may result in electric shock, fire or damage to the TV set. Don't clean the cabinet and the screen with benzene, petrol and other chemicals.
2. In order to prolong the using life of the TV set, please place it at a well ventilated location.
3. Don't place the TV set in direct sunlight or near heat source.
4. Do not place the TV set near rain or moisture as it may cause an electric shock, or the TV set to catch fire. The TV set must only be used in dry indoor location.
5. The back cover must only be removed by a registered electrical service person. Removing the back cover may result in electric shock, fire or damage to the TV set.
6. If the TV set is not going to be used for long time, or there is a severe thunder & lightening storm, it is recommended that the TV set be disconnected from the AC power outlet and the aerial plug removed.
2
I C bus control
218 programs stored
Display full functions on the screen and infrared remote control
Multi picture modes and sound modes selection
Auto searching, function selecting and program number skipping
Multifunction timer
Programs scanning
Game, Multifunction lock
Stage curtain for open and close effect
TECHNICAL SPECIFICATION
1.POWER SUPPLY: See rating plate
2.COLOUR SYSTEM: PAL N TSC4.43/3.58(AV)
3.AUDIO SYSTEM: B/G
4.CRT: 25"
5.ANTENNA INPUT : 75Ω Standard Coaxial Cable
6.SOUND OUTPUT POWER: 3W
7.POWER CONSUMPTION: See rating plate
8.NET WEIGHT(kg): 32
9.NET DIMENSION(mm): 679×472×521
Explanation on the display tube
When the picture tube requires cleaning, please disconnect the power and use a dry soft cotton cloth. Do not use any cleaner or abrasive cloth.
1
Supplied accessories: Infrared remote control handset 1 Battery(AA) 2 Operating instruction 1 Design and specifications are subject to change without notice.
2
PREPARING FOR OPERATIONS
Antenna
3
Figure A Figure B
75-300Ω
Antenna adapter
Antenna cable with a plug
Figure C Figure D
Coaxial cable(75Ω) twin-lead cable(300Ω)
Antenna feeder
Antenna connection Connect an antenna to the antenna socket on the TV set, we recommend using a Cable TV system for better picture and audio quality.
1.If you use a coaxial cable(75Ω),insert the antenna plug (see figure C) into 75Ωsocket (see figure A).
2.If you use a twin-lead cable(300Ω),please shape the cable as figure D, and connect the leads to antenna adapter and then insert the antenna adapter into the 75Ωsocket (see figure B).
Power source wire connection Insert the power plug into AC outlet. Install and replace batteries of the remote control unit:
1.Place the remote control unit with the face down, then open the battery cover of the unit.
2.Place the two"AA"size batteries, matching the + and - signs on each battery to the + and -signs of the battery compartment.
3.Close the cover of the battery compartment. NOTE: (1)Don't drop or wet or dismantle the unit. (2)If you don't intend to use the unit for a long period or the electricity of the batteries is used up, remove the batteries to prevent batteries acid from leaking into the battery compartment. (3)Replace the two old batteries at the same time. (4)Don't use charge battery (Ni-cd )and don't mix battery type. (5)Don't throw your batteries into a fire. Dispose of your batteries in a required place.
FUNCTION BUTTONS AND EXTERNAL SOCKETS
1.Front panel
(1)Remote sensor: let the remote controller aim here, the TV set can receive remote control signal. (2)Power switch: press the button to turn on the TV set ,press the button again to turn off the TV set. (3)Power indicator: the indicator lights in standby status .The indicator glints when you use remote controller. (4)Menu button (5)Program up/down button (6)Volume up/down button
MENU
TV/AV
- +VOL
-CH+
(7)TV/AV switch button
2.The sockets on the rear panel
(1)Antenna socket
(2)Audio/Video socket
(3)S-Video socket
(4)DVD component socket
(3)
S-VIDEO
IN
OUT
Y
VIDEO
Cb
3
L AUDIO R
3
ANT
Cr
VIDEO
AUDIO
(1)
(2) (4)
(2)
(3)
(1)
(4) (7)
(5) (6)
L
R
3
4
VCR (without S-VIDEO terminal)
W R
Y
AV CONNECTION
Direction of signal
W
whiteleft audio
R
redC /right audio blueC
B
3
IN
S-VIDEO
OUT
VCR (with S-VIDEO ) terminal
ti tpu ou
eo
W R
d v
-
To s
VIDEO
G
green yellow
Y
Cb
L AUDIO R
t u p
uT
e t vid o o
o
ANT
Cr
Y
r
b
Y
video
DVD(with DVD component)
T a o
u d i
o u
B
W
G R
o t
R
REMOTE CONTROLLER GUIDE
Remote control functions
1
1
2
3
4
5
20
6 7
T o
c mp e t uto
on
n o
8
9
TV/AV
1 2 3
4 5 6
7 8 9
-/--
0
SELC.PIC
CH+
MENU
VOL- VOL+
FIRE
BACK
FIRE
SECOND
CH-
MIX
SHORT
BAR
RESTART
WIDE
SCAN
LOCK
SYSTEM
DISPLAY
SELC.VOL
PRE
EXIT
LIGHT
NARROW
18
17
16
15
14
13
12
11
19
10
TV/AV exchanging button
2
Mute button
3
Numeric button
4
One/two/three digital buttons
5
Picture mode selection
6
Volume up/dwon button
7
7
Recall
8
Calendar/game selection
9
Second timer button
10
Program promote
10
11
Volume mode selection
12
12
Display
13
13
Invalid button
14
System preset button
15
Lock preset button
16
Scan button
17
DC standby button
18
Sleep timer
19
Program number up/down button
20
Menu button
Note:
1.When receive s-video signal, you must remove video signal;when receive
video signal,you must remove s-video signal.
2.When receive side video signal, you must remove back video signal; when
receive back video signal,you must remove side video signal.
5
Note :Because there is no bar function in the TV,"LONG", "SHORT",
WIDE", "NARROW" buttons are invalid.
6
POWER SUPPLY
1.Power supply (switch on/off to set main power supply).
Press power switch button and the TV set shall be under normal receiving condition.
Press it again and the power shall be off.
2.Standby button (remote control power supply).
Press the button and the TV set enters standby condition, press it again and the set
enters normal receiving condition.
TUNING PROCEDURE
TUNING PROCEDURE
(1)Press [MENU] button to let TUNING menu display on the screen. (2)Press [-CH+] buttons to select SEARCH item. (3)Press [-VOL+] buttons to change channel number into pointed channel number. (4)Press [-VOL+] buttons, when the TV set has searched a program, stop searching, if the program isn't the one you need, press[-VOL +] buttons again, the set will search continually until it has searched the program you need. And pointed program is stored in pointed channel.
4.Selecting band In the semi-auto search mode, if the signal you want to search isn't on the present band, you can change the band to improve searching speed. (1)Press [MENU] button to let TUNING menu display on the screen. (2)Press [-CH+] buttons to select BAND item. (3)Press [-VOL+] buttons to select the band you need.
VHFL
VHFH
UHF
1.Preparation
Connect the aerial and power supply
wire, press power switch button, the
power indicator will light after a few
seconds.
2.Auto-search
The TV set will automatically search all
programs, after the search is finished, all fine tuned programs will be stored (1)Press [MENU] button let TUNING menu display on the screen.
(2)Press [-CH+] button to select AUTO MEMORY item.
(3)Press [VOL+] button, the TV set will begin to search programs from program
number 0. After the search is finished, program number 0 will display on the
screen.
(4)During auto-search, if you want to stop searching, press [VOL-] button.
3.Semi-Auto search
You can preset the program you need to the pointed channel.
to
automatically.
TUNING
POSITION 1 BAND UHF SKIP OFF SEARCH UP MFT DOWN AUTO MEMORY
SELECT ADJUST
5.Fine tuning Because of some reasons, if auto searching effect of program isn't good, please fine tune your TV set. (1)Press [-CH+] buttons, and select MFT item. (2)Press and hold [-VOL +] buttons until the effects of the picture and audio are good.
6.Skip The function can skip the TV program which you don't need. (1)Press [-CH+] button or numeric button to select the program number which you want to skip. (for example: channel 002) (2)Press [MENU] button to select TUNING menu. (3)Press [-CH+] buttons to select SKIP item. (4)Press [-VOL+] buttons to preset SKIP ON mode. Note: When a certain program number is in SKIP ON mode, the program
number will not appear when you select program with the [-CH+] buttons, but program number will appear with numeric button. When a certain program number is in the SKIP OFF mode, the program number will appear when you select program with [-CH+] buttons.
7
8
PICTURE ADJUSTMENT
Press [MENU] button to select PICTURE menu. Press [-CH+] buttons to select an item. Press [-VOL+] buttons to adjust the value of the item function.
PICTURE
CONTRAST 100 BRIGHT 50 COLOR 50 SHARP 50 B.B OFF
SELECT ADJUST
Brightness adjustment: Press [-CH+] buttons to select BRIGHT item. Press [-VOL+] buttons to adjust brightness. Contrast adjustment: Press [-CH+] buttons to select CONTRAST item. Press [-VOL+] buttons to adjust contrast. Colour adjustment: Press [-CH+] buttons to select COLOR item. Press [-VOL+] buttons to adjust colour. Sharpness adjustment: Press [-CH+] buttons to select SHARP item. Press [-VOL+] buttons to adjust sharpness. Background selection: Press [-VOL+] buttons to select a background on or off.
OTHER FUNCTIONS
1.FUNCTION 1 The function can select OSD language, curtain mode,volume mode and volume memory mode.
(1)Press [MENU] button to select FUNCTION1 menu. (2)Press [-CH+] buttons to select an item. (3)Press [-VOL+] buttons to set function of the item .
Note: (1)When you select VOL STORE ON, the TV set can hold the same volume with changing channel No. .(The channel No. must be 1 between 50.) (2)When you select CURTAIN item, you can select three curtain modes: I, II and III. (3)You can not adjust the item when there is only one language OSD.
2.FUNCTION 2
(1)Press [MENU] button to select FUNCTION2 menu. (2)Press [-CH+] buttons to select an item. (3)Press [-VOL+] buttons to set function of the item . Note: (1)If you select COUNT item , you can get the total time of receiving TV program (except standby time). (2)Soft-exchanging channel No. function: Select S.C.C ON, so when you exchange channel No., the picture will fade in/out.
FUNCTION1
LANG. ENGLISH CURTAIN LOW VOL 20 NORMAL VOL 40 HIGH VOL 60 VOL STORE OFF
SELECT ADJUST
I
FUNCTION2
SUBMARINE POS.EX S.C.C OFF COUNT 13:21
SELECT ADJUST
9 10
OTHER FUNCTIONS
OTHER FUNCTIONS
(3).POS.EX item: Press [VOL+] button to enter its sub-menu(digits In POS.EX and EX.POS2 items are present channel No.). Press [-CH+] buttons to select EX.POS2 item. Press [CH+] button to put into channel No.(for example:9). Press [-CH+] buttons to select EXCHANGE item, press [VOL+] button to approve. The program in channel No. 1 will change with the program in channel No.9.
POS.EX.
EX.POS1 23 EX.POS2 23 EXCHANGE RETURN
POS.EX.
EX.POS1 1 EX.POS2 9 EXCHANGE RETURN
9
When you selectSUBMARINEgame itementer game mode and the other buttons (except [GAME],[ VOL+],[ CH+] ) are invalid.- -
Instructions of game controlling buttons
Fire button
VOL- VOL+
CH+
MENU
FIRE
CH-
Up/Down button
CALENDAR
FIRE
MIX
RESTART
Fire button
Selection buttons of game background
Game restart button
Left/right button
EXIT
LIGHT
Game exit button
3.Play game:
(1)Press [MENU] button to make FUNCTION2 menu display, and press[ -CH+] buttons to select
SUBMARINE item, then press [VOL+] button to enter SUBMARINE game mode.
(2)Press red game button and game begins, use the remote controller to operate yellow battle ship. Yellow battle ship bumps one of green ship or blue ship or purple ship or red ship or blue shot. and game is over. Yellow ship use [MENU] button or blue [FIRE] button shoot shots. The shot bump green ship or blue ship or purple ship or blue shot and win 100scores,the shot bumps red ship, and win 1000 scores.
(3)During game or game is over,press red button and game can restart. Ship obtaining highest scores wins.
I I I I I I I I I I
SCORE 000
I I I I I I I I I I
SCORE 5800 GAME OVER
I I I I I I I I I I
I I I I I I I I I I
11
12
OTHER FUNCTIONS
MULTIFUNCTION TIMER
4.System selection:
(1)Press [SYSTEM] button, OSD is as figure. (2)Press [-CH+] buttons to select an item. (3)Press [-VOL+] buttons to select a system(color system or
sound system) you need.
5.Picture mode selection: Press [SELC.PIC] button to select a picture mode you need:
DY NAMI C
STANDARD
MILD
ME M ORY
PICTURE MUTE
COLOR MUTE
6.Calendar function: (1)Press [CALENDAR] button and OSD is as figure(press the button again ,the OSD disappears.). (2)Press [-CH+] buttons to select year, press [-VOL+] buttons to select month.
SU
4
11 12
18 19 20
25 26 27 28 29
YE AR
COLOR AUTO
SOUND B/G
SELECT ADJUST
JA N 20 0 4
TU WE TH FR
MO
6
13
7
15 16 17
14
21 22
MO NT H
5
SA
1 2
8
9 10
23 30 31
3
24
Press [MENU] button to select TIMER menu. (1)Clock Press [-CH+] buttons to select CLOCK item; Press [-VOL+] buttons to set present time. Note: At first, you must set CLOCK item, then you can set other items. (2)On-timer and off-timer Press [-CH+] button to select ON-TIMER
TIMER
OFF TIMER OFF 0:00 ON TIMER OFF 0:00 POS 0 CLOCK 0:50 APPOINTMENT
SELECT ADJUST
or OFF-TIMER item, press [-VOL+] buttons to set.(ON-TIMER/OFF-TIMER can be set to ONCE or EVERY or OFF.) (3)Appointing time Press [-CH+] buttons to select appointing time item. Press [CH-] button to enter "appointing program" sub-menu. Press [-VOL+] buttons to select a channel No.(for example :100). Press [CH-] button to enter APPOINTMENT mode, then press [-VOL+] buttons to preset time. (Note:
1.Press [-VOL+] buttons once and time changes with one minute unit; press and hold [-VOL+] buttons and time changes with 10 minutes unit.
2.When it is appointing time, the TV set changes channel No. into appointing channel No. .
3.The function is valid only in TV mode.) Press [DISPLAY] button and exit APPOINTMENT
APPOINTMENT POS. TIME 001 0:01 002 0:02 003 0:03 004 0:04 005 0:05 006 0:06 SELECT ADJUST
menu.
13
14
定时关机功能
LOCK
LOCK FUNCTION
Changing password
The password of the TV set is preset "0000" in manufacture, if you want to change the password, you can fill in four digits.
1.Press [LOCK] button, OSD is as the right figure.
LOCK OR UNLOCK PASSWORD: ----
LOCK
LOCK FUNCTION
Lock preset
The TV set can lock search, channel number, AV, timer and child lock items, if you need to lock them.
1.Press [LOCK] button , OSD is as the right figure.
LOCK OR UNLOCK PASSWORD: ----
CH+
MENU
VOL-
FIRE
CH-
1 2 3
4 5 6
7 8 9
0
VOL+
2.Press "0" button directly for four times to enter LOCK OR UNLOCK menu.
Press [ CH+] buttons to
­ select "CHANGE PASS" item, then press [VOL+] button to enter "CHANGE PASS" sub-menu.
3.Press numeric buttons and fill in four digits.
4.You can fill in new password.
LOCK OR UNLOCK CHANGE PASS SEARCH LOCK OFF POS LOCK OFF AV LOCK OFF TIMER LOCK OFF CHILD LOCK OFF ALL CLEAR OFF
CHANGE PASS: NEW PASS: ----
CH+
MENU
FIRE
CH-
1 2 3
4 5 6
7 8 9
0
2.Press "0" button directly for four times (or press the
VOL+VOL-
four-digit password you have changed) to enter LOCK OR UNLOCK menu.
3.Press [ CH+] buttons to
-
LOCK OR UNLOCK CHANGE PASS SEARCH LOCK OFF POS LOCK OFF AV LOCK OFF TIMER LOCK OFF CHILD LOCK OFF ALL CLEAR OFF
select "SEARCH LOCK" item, and press [VOL+] button to select "ON" or
CHANGE PASS: NEW PASS: ----
“OFF".
Note:
1.After locking channel or AV, screen is black, no picture and no sound.
2.After locking child lock, the buttons on the TV set are invalid.
3.After locking channel search or timer, if you want to enter menu, you need to fill in password.
15
16
TROUBLE SHOOTING GUIDE
The following problems are not always caused by hardware failure, please use the follow trouble shooting guide before you call for service:
BREAKDOWN PHENOMENON
PICTURE
Picture with S now
Double or Triple Image
Disturb
SOUND
Noise
Normal
Noise
The direction and connection of the antenna
Direction, station and connection of the antenna
Interference from electric appliance. AutomobileMotor, Vehicle Fluorescence lamp etc.
CHECKING
Normal
?
??
No Picture
No Sound
No Sound
The power plug isn't plugged in AC Outlet. The main power isn't turned on. The setting up of contrast, brig­htness and volume.
Adjust color control
Volume, Sound mute
No Color
Normal Volume
Adjust channel again
Scramble
Color Spot
Normal or Weak Volume
Normal Volume
Moving the TV set or using magnetic electric appli-
ance near TV, Which will lead to color spot on sc­reen. Please remove the electric appliance and cut off power. After 120 minutes turn the TV on, the pic­ture will be recovered.
Note:1.If the problem can not be fixed after you check above items. DO NOT attempt to remove the back cover by yourself.
2.If the snapping sound from the cabinet of the TV set can be heard occasionally because of temperature changing of environment, it is normal, you can use it reassuringly.
17
Loading...