Haier 100-99VGS User Manual

Page 1
Twin-tub Washing Machine With Pump
This manual is for
User's manual
Please read this manual carefully before using. Retain it for future reference.
Page 2
Contents
Names of the parts
Preparation before washing
The musts in washing
Usage of the detergent
Washing sequence
Disposal after washing
Trouble-Shooting *Answers to question
Packing list *Specification
Page 3
Names of the parts
Water-filling entrance
Water inlet selector handle
Buzzer
Wash selector
Wash timer
Control panel
Filter frame
Lint filter
Wash tub
Pulsator
Drain hose
Wash tub cover
Base frame
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Spin tub frame
Spin tub
Cabinet
Power cord
Notes: All illustrations in this Manual are given for reference only. Your products and accessories may show differences from these illustrations due to our continuous improvement.
Meaning and description of the symbols
Warning sign
Forbidding sign
Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the personal safety of the user.
Contents marked with that symbol are actions forbidden to perform. Performing of those actions may result in damage of the machine or injure the personal safety of he user.
Please check if the power receptacle has good earthing condition before using to guarantee your safety.
1
Page 4
Safety precautions
Please insert the power cord into special receptacle with rated vol­tage.Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector.
Earth
If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the customer care department. Keep the pin of the power plug clean.
When the machine is normally using, please put the power plug at the location easily to be insert­ed and extracted by hand. Be sure to pull the plug off when there's power failure, or the machine is being moved, cleaned or when it is idle.
Do not put the machine at damp place like the bathroom . Never wash it with water. Do not place wet laundries on the control panel.
In case the washing machine is installed on ground with carpet , do not block the ventilation hole with carpet.
Ventilation hole at the bottom of the washing machine
Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use the plug any more.
Do not use water hotter than 50 C .
Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning.
2
Page 5
Safety precautions
Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children.
Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine.
Handicapped or children without care shall not use the machine.
Do not decompose, repair or alter the machine by yourself.
Do not wash laundries with volatile materials (such as thinner, petrol etc.).
Petrol
inner
Th
Keep the machine away from direct sunlight and heat source like the heater.
To protect your laundries and wash­ing machine, please take out all of the coins, buttons, sand, hairpin and other foreign materials before washing.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper. It is suggested to use foamless washing powder.
3
Page 6
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine.
Install the lint filter
Put the underside of the lint filter into overflow filter then push the upside into overflow filter
After installation,please refer that the lint filter installed to the right station,otherwise the lint filter may be falled off when washing,influencing your use.
Usage of the drain hose
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.put the drain hose up to suitable position.
2.Do not tramp or press the drain hose.
Notes: the highest point of drain pipe should be higher than
the water level of washing tub
for avoiding to siphon
phenomenon during drain.
overflow filter
lint filter
<1.2m
4
Page 7
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation position of the drain hose.
Extend the drain hose from the side of spin tub
Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet. Dismantle the drain hose fixing clamp and take the hose out of the fixing groove. (See to Figure 2).
Embed the drain hose into the groove along the side of the spin tub in the order of (1)~(3), heading for the side of the spin tub. (See to Figure 3).
Embed the drain hose into the groove with hands. Take care not to damage the drain hose in fastening the fixing clamp.
Extend the drain hose from the rear side
Dismantle the drain hose fixing clamp. Take out the drain hose from the fixing groove. Extend it from the rear side as per the direction of the arrow. (When the drain hose is extended from the rear side, it can be hung on the point for drain hose at the two sides of the cabinet.) (See to Figure 4).
Soft item
Drain hose fixing clamp
Soft item
Extend to the spin tub side
Figure 2
Embed into the groove in turn
Figure 4
Back
Front
Figure 1
Fig ure 3
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling entrance on the control panel
To dismantle the water inlet pipe, just push the control handle as indicated in the figure and pull it out
Select water level according to the
Maximum
quantity of the laundries. Set the water level adjusting lever
Medium
Minimum
to needed line.
Water inlet hose
Water level indicator
Max
Med
Min
Water level adjusting lever
Water-filling entrance
5
Page 8
Introduction of the major function
This washing machine has been provided with excellent washing performance and
luxury appearance,paeticularly for safeguard during washing.
In order to give you a quiet and comfortable washing,enclosed base frame and lower
-noise motor have been designed to reduce the noise.With Haier machine, we believe
that it is the right choice for your everyday.
Foam-removing spinning during high-efficiency rinsing
With this foam-removing spinning system,
extra detergent liquid on the clothes would
be removed rapidly and washing time can
be shortened obviously, Water saving
at the same time.
Spin
Remove most of the foam extra detergent liquid.
Foam-removing spinning
Fill water for about 1 minutes
Remove the detergent liquid remained
The effect is best when the laundries quantity is below 80% of the rated value.
Spin for about 1~2 minutes
Page 9
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe.
3.Put up the drain hose .
4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally.
Pay attention to followings before washing the laundries
<1.2m
Check if the laundries has special requirement on washing
a. Check if the laundries are applicable for washing with machine. b. Divide the laundries that are not colorfast from other laundries. c. Put those laundries difficult to absorb water into water with hand. d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil, please apply detergent on them in advance, which can make it easier to remove the soil. e. For those laundries that may get lint ball and those with long fur, turn it over before putting in. f. Do not put those laundries polluted by chemicals into the washing machine directly.
Clear the pocket. Take out the coins, sand, hairpins etc.
Tie the long strips; fasten the buttons; close zippers.
The quantity of the laundries shall not be too large. Stretch and loosen the laundries before putting them in the tub.
7
When the pulsator is running , the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries.
Page 10
The musts in washing
The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.The largest capacity of this machine is 10.0kg
The thickness ,size , type of the cloth will influ­ence the actual washing capacity. It is suit­able to put in reasonable amount of laundries and the laundries can be turned round in wash­ing for one time washing. Do not select " Max " water level for laundries less 4.0kg , so as to avoid splashing of water.
Usage of the detergent
How to use the whitener
Fill water to decided level. Dilute the whitener with container. Pour it slowly into thewashing tub.
Avoid using whitener on laun­dries with color or pattern as they are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.
For powder whitener, please dissolve it before using.
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30 seconds to dissolve it completely.
3.Put it in the laundries. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 C and a container.
2.Add the powder while stirring to fully dissolve it. The powder is more prone to pollute the laundries than the detergent. Therefore please use it with proper quantity.
Dosage of different washing powder is different. Please refer to the instruction of the washing powder for the detail dosage.
8
Page 11
Washing sequence
Water-filling selector
Wash timer
(To set to below 2 minute, first set to 5 minute then turn it back. it can increase the service life of the timer).
OFF
LINEN
WASH TIMER
SILK
WOOL
COTTON
Wash selector
(standard current, strong current)
STRONG
STANDARD
WASH SELECTOR
Buzzer
(The buzzer will ring when the washing finishes)
OFF
MAX
DRAIN
BUZZER
Wash
1.Water-filling selector Set the water inlet selector at the "WASH" side. (Figure 1)
2. Fill the water and add the dissolved washing powder to make the water level reach the preset position. (Figure 2) Run washing program for some time to stir and dissolve the powder completely.
3.Put in the laundries. If the water quantity is insufficient, please add water.
4.Select the current. Select the strength of the current according to the laundries. (Figure 3)
Water-filling entrance
SPIN TIMER
WASH
STRONG
STANDARD
WASH SELECTOR
Spin timer
(to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer).
OFF
SILK
WOOL
SPIN
Figure 1
Figure 2
DRAIN
Figure 3
OFF
SILK
WOOL
5.Select the washing time Select the washing time according to the laundries. (Figure 4)
6.After washing, the buzzer will ring. Set the "WASH SELECTOR" at "DRAIN". (Figure 5).
9
WASH TIMER
STRONG
STANDARD
WASH SELECTOR
LINEN
COTTON
DRAIN
Figure 4
Figure 5
Page 12
Midway spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push
Gland
Push
Proper
The laundries are slanting
(2) Close the inner and outer cover of the spin tub.
Outer cover of The spin tub
(3) Spin for 1-2 minutes.
3.Run the foam-removing spinning.
1
Set the inlet selector handle on spin side and
fill water for about 1 min.
In case water flows out from wash tub side
due to too much inflow, please turn down
the water tap a bit.
2
Close the spin tub outer cover and spin
for about 1 - 2 min.
Proper
No gland
Inner cover of The spin tub
WASH
SPIN
10
Page 13
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select suitable current according to the laundries.
2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously.
3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing.
(Repeat the midway spinning and rinsing with stored water for 2-3 times)
OVERFILL
If you find water flo­wing out here,please twist the water tap to limit the water filling.
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current according to the laundries.
2. Fill water to preset water level.
3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is below 4.0 kg, please use STANDARD current.If you use STRONG current, it may splash.
11
Page 14
12
Page 15
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing. It must be cleaned in time after each using.
1.
Press the elastic piece at upper end of lint filter to
release the tab from the filter cover
filter outward to remove it. (See Figure 1).
2. Remove lint
Pull the lower end of lint filter rear cover outward to disassemble it from the lint filter front cover. Remove lint completely with clear water. (See Figure 2).
3. Install lint filter
Page 4
, and pull the lint
Figure 1
Lint filter rear cover
Disassemble
Assemble
Lint filter front cover
Figure 2
Cleaning the overflow filter
Too much lint on the overflow filter will influence the normal usage of the machine. Please
clean it every two months. 1 Take off the overflow filter. As indicated in the figure, nip the elastic fixing claw and pull it to the direction of the arrow to take it off.
13
Elastic fixing claw
Page 16
Cleaning the overflow filter
2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1).
3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water.
4. Install the overflow filter. (1).Install the corrugation pipe. (2).Insert the mounting plate at the bottom of the filter into the valve cover. (3).Hang up the hook at the left upper side. (4).Push the upper part in as indicated in Figure 2.
Disposal of the complete unit
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Thinner
Petrol
Alcohol
Water level adjusting lever
Corrugation Pipe
Figure 1
Hook
Figure 2
After washing, dismount the water inlet hose. Do not store water in the tub for long period. Discharge the water immediately after each using. Pull off the power plug and hang up the power cord. Hang up the drain hose. Wipe off the water drops on the surface and inside the tub with clean soft cloth. Open the cover of the wash tub and the inner/outer cover of the spin tub for some time (about one hour), then close them.
14
Page 17
Trouble-shooting Answers to question
When the remained water is frozen
Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "WASH SELECTOR" at STRONG or STANDARD . If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
When the water is frozen Pour hot water below 50 into the wash tub to soak it completely. Then turn the pulsator with hands gently. Please confirm the drainage can work normally before next using.
Below 50
2~3L
15
Page 18
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomena The reason
Is there power failure?
The machine does not act.
Is the power plug loose? Is the pulsator twisted by foreign materials?
There's abnormal sound during washing
There's abnormal soundduring washing
There's abnormal sound and violent vibration during spinning
There may be some waterflowing out of the drain hose in the first use of the machine.
Does the drain hose put up? Is the drain hose frozen? Is the drain hose blocked by foreign material? Are there laundries falling to the outer side of the spin tub?
Are there hair pin, coins or metal items brought inside the tub?
Is the machine slanting? Is the gland pressed evenly? Are there laundries falling to the outer side of the spin tub? Are the laundries in spin tub too much?
It is the water remained in the factory inspection of performance.
16
Page 19
Packing list
Name
User's manual
Water inlet hose
Gland
Twin-tub washing machine
Specification
Water level Water quantity about
Rated washing capacity kg
Rated spinning capacity kg
Injection pressure
Quantity
One piece
One piece
One piece
One set
Maximum/99L Medium/77L Minimum/65L
10.0
6.0
0.02MPa~0.2MPa
17
Page 20
Loading...