Haicom HI-701BT User Manual

4in1

Bluetooth

Enable Car Holder

HI-701 BT

Bluetooth

®

GPS

®

GPS

USER MANUAL

1

Introduction:

HI-701 BT 4 in 1 car holder is a complete PDA car holder

solution with the following functions:

1. Charging and supply power to the PDA

2. Amplifying the PDA sound

3. Making the PDA as a GPS or Bluetooth® GPS enable unit

4. Holding the PDA in car

By changing the PDA base connector on the holder, almost any

type of PDA can be an independent and complete GPS PDA.

HI-701 BT advantages:

1. Almost any type of PDA can be used with the 4 in 1

car holder by using suitable base connector. User can

only change the base connector when he changes his

PDA. User can also use different kinds of PDA with

the same car holder.

2. Taking the GPS signal from the hinged GPS receiver

back card from the back of the holder the PDA

become a complete GPS enable PDA. The attached

GPS receiver can also act as an independent GPS

mouse by using different kinds of connecting cables.

3. HI-701 BT + GPS version make the PDA GPS enable

wire or wirelessly

1

Accessories:

Standard Accessories:

1. HI-701 BT 4 in 1 car holder

2. PDA base connector (one type)

3. DC 12V Cigarette lighter power cable

(compatible from DC12V to DC24V)

4. Hinged Bluetooth® GPS receiver back card

5. Audio cable

6. Suction cup car mount

1

2

2

2

3

3

4

5

6

3

Optional Accessories:

1. Different type of PDA base connector

2. CF slot back card

3. PS/II GPS receiver

4. External antenna

(for Hinged GPS receiver back card)

5. Mini1394 to PS/II connecting cable

1

2

4

4

5

3

4

5

5

6

Installations:

GPS receiver installation:

Slide the inclusive Bluetooth® GPS receiver into the back of the

car holder so that the PCB golden finger insert and contact

properly into the female connector inside. Based on the most

powerful and recent SiRF StarIII ultra high sensitive GPS

receiver module, the receiver can get satellite signal in very

poor reception environment.

Beside, the inclusive

Bluetooth® GPS receiver

is come with a hinge

design and can be

folded from 0 to

180 degree to

adjust the best

reception angle.

l

o

c

k

u

n

l

o

c

k

LED Indicator (Red)

LED off

LED flashing

LED stay on

Receiver switch off

GPS Position Fixed

GPS Signal searching

6

7

BT / GPS

LED indicator

LED Indicator (Blue)

LED off

LED flashing

LED stay on

Bluetooth® switch off

Bluetooth® searching

Bluetooth® connected

7

GPS Receiver

Specification

Chipset

Interfaces

Protocol

Baud Rate

Max. Update Rate

Datum

Channel

Frequency

Hot Start

Warm Start

Cold Start

Reacquisition Tike

Position Accuracy

Macimum Altitude

Maximum velocity

Voltage

Power consumption

Antenna Type

External Antenna

Connector

Dimension

LED Indicator

8

SiRF Star III

PCB golden finger & Mini-1394

NMEA0183 GGA, GSA, GSV, RMC, GLL

4800, N, 8, 1

1 Hz

WGS84

20 channel

L1, 1575.42MHz

8 sec. Average

38 sec. Average

48 sec. Average

100 ms

15m 2D RMS, SA off

18,000m

515m/s

DC 3.3V+-10%

90mA continuous mode

Built-in active antenna

MMCX (Optional)

Fold: 79 (L) x 60 (W) x 26 (H)mm

Unfold: 132 (L) x 60 (W) x 26 (H)mm

3D Positioning (blinking) or

Searching GPS (on)

8

9

Specifications:

Bluetooth®

Bluetooth®

V1.1 Compliances

Frequency Range:

Interface:

Receiver Sensetivity:

Transmitting Power:

RF Input Impedance:

Frequency hopping:

Baseband Crystal OSC:

Data Rate:

Operating Temperature:

Storage Temperature:

Transmitting Range:

Power Consumption:

2.4 ~ 2.4835 GHz
unlicensed ISM band

USB/UART/SPI

-80 dBm @ 0.1% BER

Class 2 -6 dBm ~ +4 dBm

50 ohms

1600hops/sec.

16MHz

Up to 723Kb/s

-20° C ~ +80° C

-30° C ~ +90° C

10 meters (Typical)

65 mA (Typical)

9