Haicom HI-406BT User Manual
HI-406BT
Bluetooth GPS receiver
1
Table of Contents
1.1 Overview
1.2 Main Features
2.1 Setting up: Bluetooth GPS receiver
3. Dimensions
4. Packaging
4.1 Standard Packaging
4.2 Optional Packaging
5. System Specifications
6. Get Connected; Installation Guide
6.1 Laptop PC Installations
6.2 PDA Installations
........................................... 3
..................................... 4
.......................................... 11
.............................. 12
............................... 15
............................. 19
........................ 22
................................. 25
........ 5
2
1.1 Overview
Introduction
HI-406BT is a GPS (Global Positioning System)
receiver in wireless Bluetooth interface with buildin active antenna and extra digital compass
functions. With HI-406BT, your mobile devices, such
as, Smartphone, PocketPC, laptopPC, tabletPC, etc.
can receive GPS data wirelessly and perform the
GPS applications, such as, car navigation, personal
navigation, route planning, tracking, etc.
Equipped with the most powerful and ultra high
sensitive SiRF StarIII chip set, HI-406BT can get the
3D fix in very short time and under poor reception
environment, such as in the middle of the car, next
to the tall building, in your backpack, or pocket.
3
1.2 Main Features:
• 20 Channels "All-In-View" Tracking
• Position accuracy of 10 meters 2D RMS
• Cold/Warm/Hot Start Time: 42/38/1 Seconds
(Signal Strength > 30 dB-HZ)
• Reacquisition Time: 0.1 seconds
• Support Standard NMEA-0183 at 19200 bps baud
rate (Defined by customer 4800 up to 57600)
• Support Power Saving Mode
• Compatible with Bluetooth devices with Serial
Port Profile (SPP)
• Superior Sensitivity for Urban Canyon and Foliage
Environment
• Ultra small, sleek, and lightweight design easily
fits in your hand
• Li-polymer battery lasts for more than 8 hours of
use in connection
4
2.1 Setting up:
Bluetooth GPS receiver
STEP 1:
Open the battery cap and put the battery (406-BTT)
into the battery compartment.
Push down
and pull out
5
STEP 2
Connect the AC charger to home
electronics outlet or connect the inclusive DC
charger to the car cigarette lighter. As soon as they
connected, the solid amber light on the right side in
front of HI-406BT will turned on (stay on) meaning
the battery charging.
DC charger to car cigarette
lighter (DC 12V~24V)
AC charger to home
electronic outlet
Mini-1394
female
connector for power in and GPS signal out
MMCX external antenna plug
6
STEP 3
As soon as the battery fully charged, the amber light
will turned off, then, unplug the charger.
Indicator for
power charging
and GPS status
Indicator for
battery low (Red)
and Bluetooth
status (Blue)
7
STEP 4
There is switch on side of HI-406BT. The switch on
the right side is for Bluetooth GPS receiver.
As soon as turn on the switch on the side, the GPS
receiver will start to function and search the
satellites. Meanwhile, the LED indicator on the right
side in front of HI-406BT will turned green (stay on
- the GPS receiver not get 3D fixed yet) Please
make sure place the HI-406BT outdoor open space
so that it can get the proper satellite signal. After
HI-406BT gets enough satellite data (lock more than
4 satellites), HI-406BT is in 3D fixed and the green
light start blinking.
8
Bluetooth GPS Switch
LED indicator
color
Amber
LED off
Green (blinking)
Green (Stay on)
Blue (blinking)
Blue (stay on)
Red
Status
HI-406BT battery charging
HI-406BT battery fully charged
GPS in 3D fixed
GPS searching more satellite and
not in 3D fixed yet
Bluetooth searching host device
Bluetooth paired and connected
HI-406BT battery low
9
Loading...