hager WDI07 series, WDI16 series, WDI10 series User Manual

z
r
t
s

WDI07.., WDI10.., WDI16..

Touch Panel Android/Windows
Panel táctil para Android / Windows
Painel táctil Android/Windows
Touch Panel Android/Windows

11/2014 - 6LE001039A

Contents

1 Safety instructions .......................................................................................... 3

2 Design and layout of the device .....................................................................4

3 Function ..........................................................................................................5

4. Operation .......................................................................................................8

5 Information for electricians ...........................................................................19

5.1 Installation and electrical connection ...................................................19

6 Appendix .......................................................................................................24

6.1 Technical data ..................................................................................... 24

6.2 Troubleshooting ................................................................................... 26

6.3 Accessories .........................................................................................26

z

2

Touch Panel 7´´ Android

Order no.: WDI070

Touch Panel 10´´ Android

Order no.: WDI100

Touch Panel 10´´ Windows 7

Order no.: WDI101

Touch Panel 16´´ Windows 7

Order no.: WDI161

Operating and assembly instructions

1 Safety instructions

Electrical equipment may only be installed and assembled by qualied

electricians in accordance with the relevant installation standards of the
country.

Failure to comply with these instructions may result in damage to the de-

vice, re, or other hazards.

This is equipment of class A. It can cause radio interference in residen­tial areas that the operator must counteract by means of appropriate
measures.

When supplying the system with Power over Ethernet (PoE) the overall
performance including all loads connected (e.g. USB devices) may not ex­ceed the power consumption of IEEE 802.3af class 3.

In the case of device variants with PoE functions, make sure that no dif­ferential ground potentials are used so that this function can be used.

When integrated into a door communication system (e.g. Elcom) or usage of

audio les the permissible PoE current consumption may be exceeded. This

may lead to a shutdown of the PoE supply. In this case a 24 V DC auxiliary
voltage supply is to be connected.

Do not operate the user interface with sharp-edged or pointed imple­ments.

Do not use any sharp-edged implements for cleaning. Do not use any ac­ids or organic solvents.

These instructions are an integral component of the product and must be
retained by the end user.

z

3

2 Design and layout of the device

(6)

(3)

(2)

(4)
(5)

(1)

Figure1: Front view – Example 7´´ Android variant

(1) Touch-sensitive user interface
(2) Microphone
(3) Brightness sensor
(4) Socket for mini USB 2.0
(5) Reset button R for rebooting device
(6) Speaker

(3)
(4)
(5)

(7)
(9)
(5)

(10)

Figure 2: Rear/Side view – Android device variants

z

4

(3)

(4)

(10)

(11)

(8)
(7)

(9)

(12)
(13)

(5)

Figure 3: Rear/Side view – Windows device variants

(7) Gigabit Ethernet connection RJ45, LAN/PoE (7´´/10´´ Android variant)
(8) Gigabit Ethernet connection RJ45, LAN2 (10´´/16´´ Windows variant)
(9) Connecting terminal for auxiliary voltage 24 V DC
(10) Connections USB 2.0
(11) COM1, Serial RS232
(12) Slot for SD card with rmware and operating system
(13) Connection 3.5 mm jack

3 Function

System information

The device is a display obtainable as a variant with integrated Windows
embedded (PC) or an Android operating system. The capacitive touch display
is highly suitable for the central control and visualisation of building system
technology. Operating functions and system statuses are transmitted to the
touch panel via Ethernet by means of a local server such as the domovea

z

5

Server (see Accessories), which establishes the connection to the KNX sys­tem.

In this way, for example, light can be switched and dimmed, hangings con­trolled, temperature and consumption values displayed or emails read and
sent by means of a client on Windows or external applications (Apps) in the
Android-Launcher.

Product characteristics

- Operation directly on the screen with the touch of a nger

- Multi-touch function

- Displaying of congured functions, measured values and data

- Brightness sensor for screen illumination

- USB connections for external data storage media

- Microphone and loudspeaker with echo suppression

- Silent, long-lasting convection cooling without fan

- Disabling function for cleaning the user interface by means of Touch Block­er (Windows variants)

- Applications (for Android touch panel) and iCom Module for the integration
of door communication functions in the Hager domovea client or Elcom
VideoFON client

- Visualisation for Berker IP-Control via browser

Correct use

- Only suitable for indoor applications

- The appropriate ush-mounted housing for touch panel (see accessories)

must be used for the ush-mounting in hollow walls or solid walls.

- The panel can be mounted in a horizontal or vertical direction.

Please note that the planned visualisation must correspond to the mount-

ing orientation of the touch panel. If, for example, a domovea visualisation
is implemented, both mounting orientations are only possible for the 7´´
variant. A horizontal mounting must be provided from a panel size of 10´´.

P

z

6

Figure 4: Application environment

Scope of delivery

- Touch panel

- USB/Mini USB type A adapter cable

- Installation material/tool

- RJ45 connector kit with connector and patch cable

- Operating system*) installed - depending on device variant:

- Windows7

®

embedded*) or

- Android 4.0.x

Additionally for Windows variants:

- Touch-Blocker preinstalled on the desktop

- Drivers for the hardware

- Recovery-DVD

*) Windows 7 embedded is a registered trademark of Microsoft Corporation.

domovea Client
(Android)

VideoFon Client
(Windows)

VideoFon Client
(Android)

Domovea Server

(KNX-IP Server)

IP Kamera

PoEPoE

LAN

LAN

LAN

LANPoE

Router/Switch

IP Lautsprecher SIP

Internet

Klingeltaster

Mobile
Phone

Ruf-Modul

IP Server SIP

07

31

z

7

4. Operation

The screen has a touch-sensitive surface, called touch screen. By touching the

user interface with your nger or with a special touch screen pen (not included

in scope of delivery) stored actions and functions are activated.
Do not operate the user interface with sharp-edged or pointed implements.

Depending on the software visualization, different operating modes are basi­cally possible by means of the touch-sensitive user interface (Table 1).

Operating mode Explanation with examples

short touch Switch on/off, stop, activate/deactivate, ...
long touch Change dimming value, move blind, …
Single-surface opera-

tion:

Switching on/off with the same control surface

Two-surface operation: Switching on/off using two control surfaces
Sliding Slide your nger over a control surface to variably

adjust a value, e.g.

dimming value or temperature value
Wiping For scrolling forwards or backwards through pages
Multi-Touch control Simultaneous pressing of several control surfaces to

interconnect two actions, e.g. activating function and

setting function value simultaneously

Table 1: Operating modes

If no action is executed on the display within a certain time period, the

device returns automatically to standby display (OFF or screensaver). This

time period can be congured individually – in the case of Windows vari-

ants in the control panel and in the case of Android devices by means of
Settings – Android settings – Display – Sleep in three levels
"Never, 1 Min., 5 Min., 10 Min., 30 Min.". The display is switched on again
by touching the user interface once again.

P

P

z

8

Loading  les from external data storage media

CAUTION!

The SD card slot cannot be used for external data storage media
with its own pictures, for example.

Factory settings and con gurations could be lost when removing

the SD card.

Never remove the SD card from the slot.

ç

A mini USB socket (4) is available on the upper edge of the display for loading

 les, e.g. pictures, audios, updates as well as applications (Apps/programs)

from an external data storage medium.

z If a device is mounted  ush with the wall, press left and right evenly

against the housing until the locking mechanism is audibly released.
The device is guided out of the wall. The operating elements on the upper

edge are accessible.

z Connect the enclosed adapter cable USB/mini USB to the socket (4) if

necessary.

z Connect external data storage medium, such as a USB stick or hard disk,

to the adapter cable.

z Store the data in the device or install applications using the Windows Ex-

plorer/a  le manager.

Update/Recovery of Android Touch Panels via USB stick

The system software of Android Touch Panels as well as the domovea-App
can be restored using conventional USB sticks or changed to another software
version The integrated USB update- and Recovery-function can be used in
different manners depending on the dataset used::

- Recovery: system recovery, in this case the system software is completely
overwritten on the device with a suitable system software (typically the ver­sion when supplied).

- Complete update: the system software is completely overwritten with a sui­table system software (typically a newer version).

All user data is lost when performing the recovery and complete

updates.

P

z

9

- Partial update: only parts of the system software are overwritten or written.
Partial updates can be dimensioned in such a manner that the user data is
not lost. Partial updates are particularly suitable for subsequently installing
applications or for updating.

The procedure is the same in all cases, the different effects result from the
datasets used.

The following is required in order to carry out the software installation:

- Commercially available FAT32 formatted USB memory stick with minimum
512 MB free memory.

- Mini USB adapter cable (included in scope of delivery)

- Update / recovery-dataset (.zip archive, is offered int he download area for
the product)

- Archiving software (e.g., Windows Explorer , 7zip or similar)

In order to install a system software, we recommend the following procedure.

z Download the dataset (.zip archive) from the download area for the product
z Unzip the update / recovery dataset into the root directory of the USB stick
z If a device is mounted ush with the wall, press left and right evenly

against the housing until the locking mechanism is audibly released.
The device is guided out of the wall. The operating elements on the upper

edge are accessible.

z Connect the enclosed adapter cable USB/mini USB to the socket (4) if

necessary.

z Connect the USB stick with the touch panel or adapter cable.
z Restart the Android touch panel by pressing the reset button or by discon-

necting from the power supply,
Now the update / recovery is started automatically when starting up the

device.

z Follow the instructions on the screen in order to conclude the procedure.

z

10

Restarting operating system/launcher

If the device does not react properly during operation, the system should be
restarted.

z If a device is mounted ush with the wall, press left and right evenly

against the housing until the locking mechanism is audibly released.
The device is guided out of the wall. The operating elements on the upper

edge are accessible.

z Press the sunken Reset button R using a thin pointed object.

The device will restart automatically. This may take a few seconds. When
the home page is displayed, the device is ready for operation again.

Cleaning user interface

A special disabling function, which protects the touch interface against unin­tended operations for cleaning, can be implemented on Android devices using
an App, e.g. the domovea App.

A Touch-Blocker is preinstalled on the desktop of the Windows devices.

z Start the Touch-Block by a double clicking/touching

.

On the display, a countdown takes place for 60 seconds.

z Clean the screen surface with soft, lint-free cloth. Moisten the cleaning

cloth slightly with clear water if necessary.
After the countdown has elapsed, the Touch-Block closes automatically.

The user interface is no longer blocked.

Do not use any sharp-edged implements for cleaning.

Do not use any aggressive detergents, acids or organic solvents.

Do not allow any moisture to get into the device.

P
P
P

z

11

Windows devices

The Windows device variants are supplied with a preinstalled operating sys­tem. The interface corresponds to that of a laptop or PC. Furthermore, the do­movea client is preinstalled on the desktop interface. All standard applications
and clients can be installed and used via the interface.

Android-Launcher

The Android device variants are provided with a Launcher, in which a max.
of 5 pages with control panels – 3 x 2/2 x 3 for 7´´ (Figure 5), 4 x 2/2 x 4 from

10´´ – are congurable. In the device, the Apps that can be used are already
preinstalled in a library, e.g. the Elcom App or le manager. A preinstalled App

from the library can be assigned to each free control panel (15). The domovea
App at the top left is already assigned upon delivery (14).

Depending on the mounting orientation, there is a function bar at the right or
bottom edge of the display with standard Android icons (16 …18) for naviga­tion in the Launcher (Figure 5).

domovea Browser Dateimanager

Elcom E-Mail

domovea

Browser

Dateimanager

Elcom

E-Mail

(16)

(17)

(18)

(14)

(15)

Figure 5: Launcher horizontal/vertical

(14) Control panel domovea App
(15) Free control panel
(16) Control panel recently requested Apps
(17) Control panel back to home page
(18) Control panel Back

z

12

Assigning an application to a control panel

z "Wipe" over the user interface with your nger until the required page is

displayed.

z Empty control panel > Touch for 2 seconds.

A dialogue window opens for logging in.

Before the App selection can start, the user must log in (Figure 6).

z Select Password row.

A dialogue window with a numerical keyboard opens.
z Input 4-character password using the keyboard and terminate with Done.
z In the dialog window, conrm the displayed password with OK.

The dialog window for the App selection opens (Figure 7).

The password 8273 for the Administrator and 0000 for the user is set at

the factory for the initial login.

If the wrong password is entered, the Launcher will change automatically

to the home page.
z Select the required App

The dialog window for conguration of the App display opens.
z Dene the display of the App on the Launcher page. To do this, activate

Select Icon from Library and select icon from the bottom row (Figure 8).

The selected icon is applied and displayed at the top of the page.

The row with the icons can be moved by wiping sideways in order to select

other icons.
z Give the App a name. To do this, press the input eld with the ashing

cursor.

A window with a keyboard opens (Figure 8).
z Enter the name for the App and nish the input with Done.
z With Add nish the display conguration for the App or terminate the as-

signment without saving with Cancel.

If the App is not congured or the conguration is aborted, icons and

names of the App are applied and displayed on the Launcher by the re-

spective manufacturer.

P
P

P

P

z

13

OK

Password

Password required!

Cancel

OK

8273

Password required!

Cancel

1 2 3 -

4 5 6 ,

7 8 9

0 .

Done

Done

8273

Figure 6: Login

Browser

Calculator

Calender

Contacts

E-Mail

Galerie

Music

Soundrecorder

tci Browser

Figure 7: App selection

z

14

Application
com.android.email

Name

account

Select Icon from Library

Add Cancel

Application
com.android.email

Name

|E-Mail

Select Icon from Library

Add Cancel

, .

mnbvcxy

a lkjhgfds

q1w2e3r4t5z6u7i8o9p

0

123? Done

Done

account

account

Figure 8: Conguration of the App display

Replacing/deleting the existing assignment

The user is logged in.

z An assigned control panel > Touch for 2 seconds.

Dialogue window opens.
z With Replace open the dialogue window for App selection (Figure7), select

another App and congure its display (see Assigning application to a con-

trol panel).
z With Delete release the assignment.

The control panel in the Launcher is empty.

Setting the parameters

On the last page, the settings are located unalterable in the last control panel
on the bottom right. The possible settings (Table2) are described here Change
user password as an example (Figure 10).

The user is logged in.

z Press the control panel Settings on the last page of the Launcher.

The dialog window for the selection of the setting parameters opens (Fig-

ure 9).

z

15

z Select Change user password

Dialogue window Enter new user password! opens.

z Select Password row.

A dialogue window with a numerical keyboard opens.

z Input new 4-character password using the keyboard and terminate with

Done.

z In the dialog window Enter new user password! conrm the displayed

password with OK.

z Similarly, repeat the input of the new password and nish with OK.

The device conrms the new setting with the message Password changed.

Change user password

Change administrator password

Sound volume settings

Android settings

Close

Shutdown

Logout

Reset Launcher

Backup configuration

Save

Save

ICOM HW

3

Audio preset

Pages

Start App

Figure 9: Setting parameters when logging in as Administrator

z

16

Change user password

Change administrator password

Sound volume settings

Android settings

Close

Shutdown

Logout

Reset Launcher

Backup configuration

Save

Save

ICOM HW

3

Audio preset

Pages

Start App

OK

1234

Enter new user password!

Cancel

Change user password

Change administrator password

Sound volume settings

Android settings

Close

Shutdown

Logout

Reset Launcher

Backup configuration

Save

Save

ICOM HW

3

Audio preset

Pages

Start App

OK

1234

Retype password!

Cancel

Change user password

Change administrator password

Sound volume settings

Android settings

Close

Shutdown

Logout

Reset Launcher

Backup configuration

Save

Save

ICOM HW

3

Audio preset

Pages

Start App

OK

Password

Enter new user password!

Cancel

1 2 3 -

4 5 6 ,

7 8 9

0 .

Done

Done

1234

Figure 10: Changing the user password

Parameters Setting

Change user password

1)

Enter new 4-character password,

conrm

Change administrator pass­word

Enter new 4-character password,

conrm

Pages Change and save the number of Launcher

pages using icon
Audio preset Select ICOM SW, ICOM HW, save
Sound volume settings

1)

Set, conrm volume of videos, music, lan-

guage and notications variably by "sliding"

Select, conrm silent mode Off, mute sound

for notications

Activate/deactivate sounds by touching

z

17

Parameters Setting

Android Settings Congure network with WLAN, Ethernet or

Proxy
Set sounds, display for device, infor mation
for memory, display Apps
Store user prole with account, security and
language settings
Set/display system data, such as date &
time, operational aids, developer options,
via the tablet

Start App Starting an App, which e.g. is not perma-

nently assigned in the Launcher

Backup conguration The message Conguration saved suc-

cessfully conrms that the device settings

have been saved

Shutdown

1)

After conrming with OK, the message
Power off signals the process. Device shuts

down.
The device can be rebooted using the reset
button R.

Reset Launcher All congurations in the Launcher are dele-

ted with OK. Delivery condition
is restored. User is logged off.

Close

1)

Return to the Launcher page with the
App Settings

Logout

1)

Logout

1)

When logging in as a user, only the marked setting parameters can be changed.

Table 2: Settings

z

18

5 Information for electricians

5.1 Installation and electrical connection

DANGER!

Touching live parts in the installation environment can result in
an electric shock.

An electric shock can lead to death.

Disconnect the connecting cables before working on the device
and cover all live parts in the area!

ç

Preparing installation

As a display and operating panel, the device should be mounted in a place
that is easily accessible. The user habits are decisive when determining the
installation height. We recommend an installation height from the display/hous-

ing centre to the  nished  oor of approx. 1.65 m.

Direct sunlight or powerful light sources

could impair the brightness sensor.

Prevent humidity and excessive dust at the installation location. Do not

install the device near heat sources, such as radiators, storage heaters or
ovens.

The touch panel must be installed in a separately available  ush-mounted

housing (see accessories).

CAUTION!

Damage to the device if installed in a warped housing.

The device can be damaged.

When installing the housing in a wall, ensure that the wall
opening is big enough and the device can be inserted without
without tensions.

ç

Information concerning the installation of the  ush-mounted housing in

solid and hollow walls can be referred to in the instructions enclosed.

To avoid EMC interference, do not install network input cables parallel to

mains cables.

P
P

P
P

z

19

Prepare the supply voltage

Respective connection cables should be provided for the power supply of the
device.

The Windows versions must be connected to a power supply 24 V DC (see
accessories).

The Android versions have a limited PoE capability. When selecting the supply
voltage, the intended use must be considered.

A 24 V DC auxiliary voltage is available when

- the device is integrated into a door communication system (Elcom)

- Audio-les are played-back (music, internet-radio)

- no PoE-supply (Power over Ethernet) is available)

Ongoing exceeding of the permissible PoE-power consumption, from

increased use of the audio applications may lead to the PoE power supply
switching off.

Installing connector (RJ45) on the network cable (gure 11)

The ush-mounted housing is installed rmly in the wall. The empty conduit

with the network cable is guided through an entry on the housing.

z Insert the network cable through the metal cap's earthing cover of the

connector.
z Strip the Ethernet strands of the network cable, do not remove insulation.
z Insert the strands into the plug-in connector (19) of the connector and bend

up 90°. Shorten any protruding strands.

When doing so, it is imperative to observe the colour code EIA/TIA -568 A

or B of the system. This can be found in the documentation of the installed

network components and routers. The Ethernet connection has been con-

nected to the device compatible with wired networks in accordance with

TIA/EIA-568-A or B
z Insert the plug-in connector into the connector (20) and snap it shut.

The plug-in connector is locked in place in the connector.
z Tighten the enclosed cable tie over the earthing cover.

P

P

z

20

a

b

87

6 5 4 3

21

a

b

a

8 7

6 5 4 3

2 1

87

6 5 4 3

21

a

b

> 60 mm

a

b

T568A

T568B

T568A T568B

87

2 1

T568B

3456

87

2 1

T568A

3456

20 mm

87

6 5 4 3

21

20

a

b

c

8 7

6 5 4 3

2 1

8 7

6 5 4 3

2 1

a

b

87

6 5 4 3

21

Click !

(19)

(20)

Figure 11: Installing connector on the network cable

z

21

Connecting and installing the device

The RJ45 installing connector is mounted on the network cable.

z Connect the jack to an RJ45 socket on the touch panel (7/8) using the

enclosed, pre-assembled RJ45 patch cable.
z If required connect a 24 V DV auxiliary voltage (see Accessories) using the

enclosed terminal (9). Ensure correct polarity ( gure 2/3).

Recommendations for connecting the supply voltage, see Prepare the

supply voltage.
z Insert touch panel in the housing (21) in such a way that the mounting

plates (22) of the housing are pushed under the frame.
z Tighten the four screws and the mounting plates through the frame from

above and below using the enclosed Allen key (Figure 12/13).

The screws must be countersunk in the frame.

(21)

(22)

(22)

Figure 12 a/b: Installation in the  ush-mounted housing

(21) Flush-mounted housing (not included in scope of delivery)
(22) Mounting brackets

z

22

z If a device is mounted  ush with the wall, guide it into the housing by

applying even, slight pressure on the left and right (Figure 13) until the

>>

Push-to-open

<<

lock of the housing engages.

When pushing in the touch display into the housing, make sure that the

connected cables do not get wedged in.
z Remove the protective foil from the user interface.
z Switch on auxiliary voltage.

The device charges the operating system/Launcher and displays the

desktop interface/home page of the Launcher after a few seconds. Device is

ready for operation.

(23)

(22)

(22)

Figure 13 a/b: Flush wall mounting installation in the  ush-mounted housing

(23) Flush-mounted housing,  ush-to-wall (not within scope of delivery)

P

z

23

Dismantling the device

z If a device is mounted ush with the wall, loosen it from its fastening in the

ush-mounted housing by applying even, slight pressure and release.

The device will move slowly forward out of the housing.
z Loosen the screws and remove the device from the housing.
z Remove connections.

6 Appendix

6.1 Technical data

Capacitive TFT touch display approx. 16:9
Storage temperature -20 … +60 °C
Air humidity 10 … 90 % at 25 °C, non-condensing
Degree of protection IP20
Cable cross-section of auxiliary voltage:

- exible with conductor sleeve max. 0.75 mm

2

- rigid max. 1.5 mm

2

Conformity according to EMC Directive 2004/108/EC
Voltage Directive 2006/95/EC

Standards EN 55022: 2010 Class B
EN 55024: 2010
EN 60950-1 : 2006 + A2: 2013

7´´Android variant:

Resolution 800 x 480 pixels
Light intensity 300 cd/m

2

Data transmission Ethernet 10/100 Mbit/s
Port Ethernet 1 x RJ45
Power supply via:

- PoE (Power over Ethernet) or

- Auxiliary voltage 18 … 48 V DC

Power consumption:

- PoE (visualisation only) max. 13 W

- with auxiliary voltage (audio-playback, door communication) max. 18 W
Processor 1 GHz CPU "DaVinci" DM3750 Coretex A8
Main memory 512 MB RAM

8 GB ash on SD card

z

24

Operating temperature +5 … +45 °C
Dimensions (W x H x D) 189.7 x 125. x 48.3 mm
Assembling height of frame 12 mm

10´´Android variant:

Resolution 1280 x 800 pixels
Light intensity 300 cd/m

2

Data transmission Ethernet 10/100 Mbit/s
Port Ethernet 1 x RJ45
Power supply via:

- PoE (Power over Ethernet) or

- Auxiliary voltage 18 … 48 V DC

Power consumption:

- PoE (visualisation only) max. 13 W

- with auxiliary voltage (audio-playback, door communication) max. 18 W
Processor 1 GHz CPU "DaVinci" DM3750 Coretex A8
Main memory 512 MB RAM

8 GB ash on SD card

Operating temperature +5 … +45 °C
Dimensions (W x H x D) 259.4 x 177 x 67.5 mm
Assembling height of frame 10 mm

10´´ Windows variant:

Resolution 1280 x 800 pixels
Light intensity 300 cd/m

2

Data transmission Ethernet 1000 Mbit/s
Port Ethernet 2 x RJ45
Auxiliary voltage 24 V DC
Power consumption max. 20 W
Processor AMD Dual Core CPU T40E, 2 x 1.0 GHz
Main memory Graphics Radeon HD6320, 2 GB DDR3 RAM
Operating temperature +5 … +35 °C
Dimensions (W x H x D) 259.4 x 177 x 67.5 mm
Assembling height of frame 10 mm

z

25

16´´ Windows variant:

Resolution 1366 x 768 pixels
Light intensity 220 cd/m

2

Data transmission Ethernet 1000 Mbit/s
Port Ethernet 2 x RJ45
Auxiliary voltage 24 V DC
Power consumption max. 20 W
Processor Core CPU T40E, 2 x 1.0 GHz
Main memory 2 GB DDR3 RAM
Operating temperature +5 … +35 °C
Dimensions (W x H x D) 377.4 x 231.8 x 66.4 mm
Assembling height of frame 11 mm

6.2 Troubleshooting

Display surface does not react to operations anymore

Cause: System has been shut down or has crashed.

Press the reset button R (5).
The device will automatically restart.

Operation not possible

Cause: Auxiliary voltage is not present.

Check connection for auxiliary voltage.
Check auxiliary voltage by means of measuring device.

6.3 Accessories

Housing ush-mounted for WDI07x WDW070
Housing ush-mounted for WDI07x, ush-to-wall WDW071
Housing ush-mounted for WDI10x WDW100
Housing ush-mounted for WDI10x, ush-to-wall WDW101
Housing ush-mounted for WDI16x WDW160
Housing ush-mounted for WDI16x, ush-to-wall WDW161

Power supply 24 V DC RMD TGA200
domovea Server REG TJA450

z

26

z

27

Contenido

1 Indicaciones de seguridad ............................................................................29

2 Estructura del aparato .................................................................................. 30

3 Función .........................................................................................................31

4. Manejo .........................................................................................................34

5 Información para el electricista .....................................................................45

5.1 Montaje y conexión eléctrica ............................................................... 45

6. Anexo...........................................................................................................50

6.1 Datos técnicos ..................................................................................... 50

6.2 Ayuda en caso de problemas .............................................................. 52

6.3 Accesorios ........................................................................................... 52

r

28

Panel táctil 7" para Android

N.º de pedido: WDI070

Panel táctil 10" para Android

N.º de pedido: WDI100

Panel táctil 10" para Windows 7

N.º de pedido: WDI101

Panel táctil 16" para Windows 7

N.º de pedido: WDI161

Instrucciones de uso y de montaje

1 Indicaciones de seguridad

La instalación y montaje de aparatos eléctricos solo puede llevarse a ca­bo por personal técnico especializado de acuerdo con las normas de ins­talación pertinentes del país.

Si no se tienen en cuenta las instrucciones, pueden producirse daños en
el aparato, un incendio u otros peligros.

El aparato es un dispositivo de clase A. Este dispositivo puede ocasio­nar interferencias en el entorno doméstico a las que el usuario tendrá
que hacer frente adoptando medidas propias.

Para suministrar corriente al sistema con Power over Ethernet (PoE), la
potencia máxima con todos los cargas conectadas (p.ej. dispositivos
USB) no debe superar el consumo de potencia de IEEE 802.3af Class 3.

En el caso de variantes del aparato con función PoE, es necesario obser-

var que no se utilicen diferentes potenciales de tierra para poder utilizar

esta función.

En caso de integración en una instalación de comunicación para una puerta,

(p.ej. Elcom) o al utilizar archivos de audio puede rebasarse el consumo de

corriente PoE admisible. Ello puede provocar la desconexión de la alimenta­ción PoE. En dicho caso deberá instalarse una tensión auxiliar de 24 V DC.

No puede manejarse el panel de mando con objetos cortantes o puntiagudos.

No utilice objetos cortantes para limpiar. No utilice ácidos o disolventes
orgánicos.

Estas instrucciones son un componente del producto y deben permane-

cer en posesión del usuario nal.

r

29

2 Estructura del aparato

(6)

(3)

(2)

(4)
(5)

(1)

Figura 1: vista frontal; ejemplo de variante Android 7"

(1) Panel de mando con pantalla táctil
(2) Micrófono
(3) Sensor de luminosidad
(4) Hembrilla para Mini-USB 2.0
(5) Tecla Reset R para reinicio del aparato
(6) Altavoz

(3)
(4)
(5)

(7)
(9)
(5)

(10)

Figura 2: vista trasera / lateral; variantes de aparato Android

r

30