1 6T 7972-02b
6T 7972-02.b
TRE50., TRE52.
§
220° Motion Detectors
User instructions
¨
RFTP
230V~
Bus
30 V
V2.5.1
ACCESSORY FOR
ANGLE FIXING
EE855 White
EE856 Anthracite
52125 White
52126 Anthracite
220° DETECTORS
TRE500 White
TRE501 Anthracite
TRE520 White
TRE521 Anthracite
15 min
s
5 min
auto
-
+
lux
test
30
α
IP55
+ 90°/- 30°
+/-80°
Description
Detection zone
Installation
Wall fixing plate
Adjustment potentiometers
Directional detection head
Adjustments
Shutters
Angle fixing support
Vertical adjustment
Optimal installation height is 2.5m.
The detection zone shall remain free of obstacle.
8 m 16 m
2,5 m
0,5 m
16 m
4 m
LED A LED B
Delay
(lighting time)
Brightness
level
Sensitivity
(change
of range)
1
2
2 6T 7972-02b
Warning :
This device is to be installed only by a
professional electrician fitter according to
local applicable installation standards.
Test and validation of detection
zone
Set potentiometer 2to Test mode.
The Test mode is available for 3 minutes time
and does not take brightness level into
account.
Each detected movement turns LED A on for 2
seconds.
The associated receiver is not under control.
After 3 minutes without detection, the product
is set back to auto mode.
Limitation of detection zone:
You can limit the detection zone using the
shutters supplied or by inclining the head.
Mounting
Projection or ceiling mount :
- Fix the wall plate using the supplied screws.
- Clip the detector onto the wall plate
- Tighten the screws to close.
For angle mounting, the wall fixing plate is
fitted between the accessory and
the detector.
Precautions for installation
For optimum detection conditions, please
follow these recommendations :
- Keep the detector protected from solar
radiation and bad weather, as it is sensitive
to these conditions.
- Maintain 1m distance between the light
source and the detector and keep the
detector out of the light source.
Product Description and working
principles
This detector allows remote control of one
or more receivers for a given time when a
movement is detected in its detection zone.
This product can be used in two types of
configuration: one detector controls
one/several receiver(s); several transmitters
control the receiver(s).
Operation
The receiver(s) is(are) under control as soon as
the brightness level as set by potentiometer
2
is considered too low and a movement is
detected.
Upon detection, the time delay is restarted.
If LED A flashes quickly during configuration,
the position of potentiometer
1
is not compa-
tible with the selected function.
If LED B flashes quickly or nothing occurs
when starting configuration, check that the
batteries are correctly installed and replace
them if necessary. Product factory reset is
recommended before any new configuration.
Factory return
Keep push-button J depressed until LED
cfg (flashes (>10s), and then release it.
LED cfg is turned off when factory return is
completed.
This operation causes full delete of product
configuration in any configuration mode.
After factory return, wait 15s before starting.
Action Adjustments Potentiometer
Use Auto (factory)
settings to set
automatic lighting
turn-on for
a given time.
Only available when
a detector’s time
delay is set.
Auto Settings
Put the Lux potentiometer on
“auto test”.
The settings are predefined :
Lux = ,
(operating at night only)
time = 3 min,
sensitivity = max
auto
lux
test
Turn automatic
lighting on for
a given time.
Only available when
a detector’s time
delay is set.
Installer settings
15 min
30 s
5 min
auto
-
+
lux
test
Test and confirm
detection zone.
Test mode
Move the potentiometer
2
to “auto test”.
auto
lux
test
auto
lux
test
Adjust sensitivity. Allows setting the range
to avoid disturbance.
-
+
Hereby, hager Controls, declares that this motion detector
output is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
The CE declaration can be consulted on the site :
www.hagergroup.net
Usable in all Europe and in Switzerland
Installing batteries
J Button
cfg
c
f
g
LED C
Button J
Configuration (button J )
These detectors can be configured in 3 different
ways :
• : tool-free configuration (using product
pushbuttons and LEDs), see User's Instructions
6T7952 supplied with the product.
• TX100/B V2.5.0 or above:
description of product functions available from
the Manufacturer.
• ETS3 or via TR131: database and description of
application software available from the
Manufacturer.
Configuration by TX100 or ETS
Set the product in configuration mode by pressing
J button once during the teaching session of
TX100 or for addressing with TR131 in ETS.
O
Product factory return is required to change
the configuration mode.
quicklink
Loading...