Hager KLDS8, KLDS4, KLDS6, KLDS10, KLDS12 Installation Instructions

Wiring

Single Circuit Switching

With the Copper Link (1) in place, the
switch return can be wired to terminal
SW(A) or SW(B) to swtich all outgoing
ways.

Dual Circuit Switching

For dual circuit switching remove the
Copper Link (1). Terminal SW(A) will
switch outgoing ways marked as
Circuit A, and Terminal SW(B) will
switch outgoing ways marked as
circuit B.

Flexible Cords

Conductors of exible cords should
not be connected into the main terminal
block. A separate terminal block is
provided for connecting any switching
devices using a exible cord e.g. hager
EEK513W occpuancy sensor.
Maximum rating for this terminal block
is 10A.

Normally
open retractive
wall switch

Terminal
block
wall
switch
(grey)

klik.LDS with all ways switched by
a single hager EEK513W occupancy
sensor

Circuit B

LOOP

N

SW(B)

SW(A)

AUX

Copper Link (1)

Copper Link (2)

LOOP

NEUTRAL

SWITCH
RETURN

Circuit A

LOOP (brown)

NEUTRAL (blue)
Sw B (black)
Sw A (black)

EEK513W

klik.lighting distribution system

KLDS12

KLDS10

Wiring Diagrams

For emergency lighting arrangements
refer to the following wiring diagrams.

‘Local’ lighting switch control

E

N

Emergency

test

switch

To lighting distribution board

Centralised emergency test via keyswitch

L

Aux
Loop

N
Sw(B)
Sw(A)

Local lighting switch

Copper Link(2)

To other
LDS box

E

N

E

N

To lighting distribution board To lighting distribution board

Emergency test
switch N/C

‘Local’ lighting switch control
Permanent emergency feed

L

Local lighting switch

Zone lighting control
‘Local’ emergency test control

L

Zone switch to other LDS box

Aux

Copper Link(2)

Loop

N
Sw(B)
Sw(A)

Aux

Remove Copper Link(2)

Loop

N
Sw(B)
Sw(A)

To other
LDS Box

Hager Ltd

Hortonwood 50

KLDS8

Telford
Shropshire
TF1 7FT

Sales Hotline:
Tel: [phone]
Fax: [phone]
[e-mail]

Technical Support Line:

KLDS6

Tel: [phone]
[e-mail]

This product should be installed by a competent person
(e.g. a qualied electrician) in accordance with these
instructions and the appropriate clauses of the IEE Wiring
Regulations (BS7671).

KLDS4

469212C10 iss A

Hanging from ceiling suspension systems

A.

Attach spring channel nuts to ceiling
channel.

B.

Attach spring channel nuts to the
opposite end of suspension rod and
place in T-slot in box.

Mounting Positions

Top

Rear face

Bottom

There is a choice of three mounting

C.

positions top, bottom or rear face.

Fixed to trunking

A.

Remove end cover.

B.

Drill a 20mm dia hole in the base of the
lighting trunking at the position where
cable entry to the LDS box will be.Drill
a second hole 6mm dia clear to line up
with the xing hole at the non terminal
end of the LDS box.

A
B

4 way A = 155 B = 193
6 way A = 205 B = 243
8 way A = 255 B = 293
10 way A = 305 B = 343

Fixed to solid surface

A.

Remove end cover.

Fitting
postions

130mm

Drill holes through terminal end in

B.

recess on inside face of terminal
compartment through
the xing holes at t
end.
Fixing centres ‘A’ are
4 way = 208 8 way = 308
6 way = 258

dimples. Use

he non terminal

10 way = 358

A

To enable entry of wiring system

D.

remove appropriate knockouts
connect and terminate

C.

Using an appropriate conduit tting.
Attach the box to the trunking via the
20mm hole and use a M6 nut and bolt
through the 6mm hole. Run cables
through conduit tting and terminate
cables. (See wiring diagrams)

C.

To enable entry of wiring system
remove appropriate knockouts
connect and terminate conductors.
(See wiring diagrams)