hager I-EA00116 Installation Instructions Manual

Download

Page 1

433 MHz Transmitters & Reciever

Installation Instructions

Digital Transmitters and Receiver with Sequencing Function

I-EA00116

1 Description

The 433MHz Series Transmitters and 2-659-0183 Receiver are ideal for the wireless activation and/or sequencing of automatic doors. The transmitters are available in hand-held or pushplate styles and they transmit a unique rolling code each time the transmitter is activated (thus providing a secure door opening signal). The transmitter PN: 2-659-0185 is powered by a 9-volt battery whereas all other transmitters are powered by a 3 volt battery and all illuminate a Red LED when activated.

Since receivers can be individually programmed, multiple receivers can be programmed differently thus allowing for sequencing in multiple applications. Upon activation (pushplate / transmitter), all receivers will acquire the signal at the same time; however, each receiver will respond according to their programming. Those receivers programmed with NO DELAY will active immediately upon receiving the transmitter signal. Those receivers programmed with a DELAY will activate at the end of their pre-determined time delay set by the potentiometer. The use of multiple receivers will allow for the uninterrupted pace or hands free operations through a pair of doors upon initial activation.

2-659-0186

ONE BUTTON

2-659-0184

3V w / LEADS

2 Specifications

DESCRIPTION SPECIFICATION

FREQUENCY 433 MHz

EMITTED RADIO POWER -28.7 dBm (Transmitter)

POWER CONSUMPTION 3mA (Transmitter) 30mA (Receiver)

INPUT VOLTAGE 12 to 24 VAC/DC (Receiver)

CONTACT RATING 1.0 A @ 30 VDC / 0.3 A @ 60 VDC

OPERATING TEMPERATURE 14ºF TO 131ºF (-10ºC TO 55ºC)

MAX No. OF PROGRAMMED UNITS PER RECEIVER

LEDs Receiver Learn

Relay Activation

DIMENSIONS Transmitter

Receiver

CERTIFICATIONS FCC, IC,

0.5 A @ 125 VAC

100 TRANSMITTERS

RED BLUE

2 3/4” X 1 3/8” X 9/16” (70mm x 35mm x 14mm) 2 3/4” x 2 1/8” x 1” (70mm x 55mm x 25mm)

3 Precautions

2-659-0183

TERMINAL

STRIP

2-659-0185

9V w / LEADS

DIP

SWITCH

LEARN WITH

DELAY BUTTON

ANTENNA WIRE

BLUE LED

RED LED

LEARN W/O DELAY BUTTON

DELAY POTENTIOMETER (Time Adjustment)

This product IS NOT intended for use with Maglocks / Electric Strikes. Contact Hager Companies for further information.

Shut off all power going to work area before attempting any wiring procedures.

Maintain a clean & safe environment when working in public areas.

To remain in compliance with Part 15.231, do not operate transmitter (hold down button ) for longer than 5 seconds.

Constantly be aware of pedestrian trafﬁc around the area.

Always stop pedestrian trafﬁc through the doorway when performing tests that may result in unexpected- reactions by the door

ESD: Circuit boards are vulnerable to damage by electrostatic discharge. Before handling ensure you dissipate your body’s charge.

Always check placement of components before powering up so that moving parts will not catch any wires or cause damage to equipment.

Ensure compliance with all applicable safety standards (i.e. ANSI A156.10 / 19) upon completion of installation.

DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by Hager Companies. Unauthorized disassembly or repair:

1. May jeopardize personal safety and may expose one to the risk of electrical shock.

2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.

07/24/2013 Hager Companies • 139 Victor Street • St. Louis, MO 63104 • 800 325 5559 • www.hagerco.com Page 1 of 4

Page 2

4 Programming

1 DIP SWITCH SETTINGS

433 MHz Transmitters & Reciever

Installation Instructions

Digital Transmitters and Receiver with Sequencing Function

I-EA00116

# 1 DESCRIPTION FUNCTION

OFF Pulse Relay Press the transmitter once and the relay will be active momentarily.

ON Toggle Relay Press the transmitter once and the relay output is active indeﬁnitely,

press it again and the relay will de-energize indeﬁnitely.

# 2 DESCRIPTION FUNCTION (Pulse Mode Only)

OFF 0.5 sec Hold Time Relay will remain active 0.5 second after the loss of activation.

ON 10 sec Hold Time Relay will remain active 10 seconds after the loss of activation.

1 2

PUL TOG

In Toggle Setting (1-ON), the Hold Time

is inactive. Either setting for #2 dip

switch will have the same result.

1 2

PUL TOG

0.5 second

Pulse Setting

0.5s l 10s

1 2

PUL TOG

1 2

PUL TOG

10 second

Pulse Setting

2 HAND HELD CONFIGURATION

1. Set dip switches on the receiver to the desired activation cycle (dip switch 1 -Toggle or Pulse and dip switch 2 - 0.5s or 10s hold).

2. Press either Learn w/Delay Button or Learn w/No Delay Button on the receiver depending on the activation requirements (If delay learn is selected, adjust potentiometer to counterclockwise limit, 0 second delay). After learn cycle is complete, adjust potentiometer to desired delay time (0-30 sec).

3. Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter).

NOTE: Repeat Steps 2-3 to program additional transmitters.

4. To test the system, depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver. This indicates that the relay has been activated.

3 PUSH PLATE CONFIGURATION

1. Before beginning, it is easiest to have already prepared the installation of the push plate.

2. Connect the wires from the transmitter to the NO and COM contacts of the push plates switch.

3. Follow Steps 1-4 (Hand-Held Conﬁguration); depress the pushplate to activate the transmitter.

4. Attach the transmitter to the inside of the electrical box and complete the installation.

0.5s l 10s

4 TYPICAL VESTIBULE APPLICATION

A OUTSIDE TRANSMITTER (PUSH PLATE)

1. Press Learn w/NO DELAY BUTTON on OUTER Receiver then press Transmitter 1.

2. Press Learn w/DELAY BUTTON on INNER Receiver then press Transmitter 1.

NOTE

: Set Potentiometer to desired Delay Time per Hand Held Conﬁguration Step #2.

B INSIDE TRANSMITTER (PUSH PLATE)

1. Press Learn w/NO DELAY BUTTON on INNER Receiver then press Transmitter 2.

2. Press Learn w/DELAY BUTTON on OUTER Receiver then press Transmitter 2.

NOTE

: Set Potentiometer to desired Delay Time per Hand Held Conﬁguration Step #2.

C VESTIBULE TRANSMITTERS (Dual Switch Push plate or Two Separate Push plates)

1. Press Learn w/NO DELAY BUTTON on INNER Receiver then press Transmitter 3.

2. Press Learn w/NO DELAY BUTTON on OUTER Receiver then press Transmitter 4.

INNER RECEIVER

5 REMOVING TRANSMITTER CODE(S)

SINGLE TRANSMITTER CODE

1. Press both DELAY and NO DELAY BUTTONS simultaneously until Red LED ﬂashes once (approximately 1 second).

2. Press transmitter button twice within 10 seconds and the transmitter code will be deleted.

ALL TRANSMITTER CODES

1. Press and hold both DELAY and NO DELAY BUTTONS simultaneously until Blue LED illuminates then release (approximately 10 seconds).

OUTER RECEIVER

07/24/2013 Hager Companies • 139 Victor Street • St. Louis, MO 63104 • 800 325 5559 • www.hagerco.com Page 2 of 4

Page 3

5 Wiring

Power VAC/DC Output

Label 12 - 24 12 - 24 Com. N.O. N.C.

Wire Color Red (+) Black (-) White Green Grey

Terminal 1 2 3 4 5

Description

Control or Transformer power Control Common Control Activation Typically not used

6 Battery Replacement

433 MHz Transmitters & Reciever

Installation Instructions

Digital Transmitters and Receiver with Sequencing Function

I-EA00116

CAUTION: THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.

DISPOSE OF USED BATTERIES ACCORDING TO ITS INSTRUCTIONS.

1 3 - VOLT TRANSMITTERS

1. Remove two screws from back of transmitter.

2. Separate housing and install a fresh 3-Volt (Type CR2032) battery making sure to observe proper polarity.

3. Reassemble housing and replace screws.

NOTE: Don’t throw used batteries away with the general trash. Discard per your local municipal laws and regulations.

2 9 - VOLT TRANSMITTER

1. Remove old battery.

2. Connect a fresh 9-Volt (Type 6LR61) battery making sure to observe proper polarity.

NOTE: Don’t throw used batteries away with the general trash. Discard per your local municipal laws and regulations.

7 FCC Compliance

• This Digital Transmitter complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference and;

2) This device must accept any interference received including interference that may cause undesired operations.

a) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

• This transmitter operates in the band 433.5- 434.5 MHz and is restricted to periodic transmissions of up to 5 seconds.

• Changes or modifications not expressly approved by BEA, Inc. for compliance could void the user’s authority to operate the equipment.

• Devices authorized under these provisions shall be provided with a means for automatically limiting operation so that the duration

of each transmission shall not be greater than 60 seconds and be only permitted to re initiate an interrogation in the case of a transmission error.

FCC ID#: G9B-10TD433HH4 IC ID#: 4680A-10TD433HH4

07/24/2013 Hager Companies • 139 Victor Street • St. Louis, MO 63104 • 800 325 5559 • www.hagerco.com Page 3 of 4

Page 4

433 MHz Transmitters & Reciever

Installation Instructions

Digital Transmitters and Receiver with Sequencing Function

I-EA00116

8 Troubleshooting

Problem: THE RED LED ON MY RECEIVER IS JUST FLICKERING AND I’M UNABLE TO PROGRAM AND/OR IT WON’T WORK.

Solution:You have a push plate stuck or faulty transmitter. Disconnect each push plate until the LED goes out. If LED does not go out, remove

each transmitter battery until it does. Replace the appropriate transmitter.

Problem: HOW DO I ERASE ONLY ONE TRANSMITTER CODE?

Solution: & no gnihsaﬂ strats DEL der eht litnu ro dnoces 1 .xorppa rof reviecer eht no ylsuoenatlumis snottub yaled on dna yaled eht htob sserP

off then release. Press the transmitter button twice within 10 seconds and the given transmitter code will be deleted.

Problem: HOW DO I ERASE THE MEMORY ON THE 433 RECEIVER?

Solution:

Problem: RECEIVER INTERMITTENTLY DOESN’T RECEIVE THE TRANSMITTER(S) SIGNAL.

Solution: You may extend the receiver antenna wire only in multiples of 6.75” (6 3/4”). i.e. 6.75 x 4 = 27 inches of extended antenna wire

Press both the delay and no delay buttons simultaneously on the receiver until the blue LED illuminates then release (aprox. 10 seconds).

07/24/2013 Hager Companies • 139 Victor Street • St. Louis, MO 63104 • 800 325 5559 • www.hagerco.com Page 4 of 4