Hager EG403E User guide

Download

Page 1

135

246810 12 14 16

11 13 15

7 9

L N

Navigation &

value setting

Validation

Enter in PROGRAMME mode &

return to previous step

Selection of days of the week

1 = Monday, 2 = Tuesday

... 7 = Sunday.

Canal B command

Canal C command

Canal D command

Canal A command

DCF Antenna (option)

Keyboard locked by PIN code

4 channel programmer

User instructions weekly cycle with programming key

6E 6354E

EG403E

Presentation

⦁ Product delivered with current time and date set. ⦁ Automatic change of summer/winter time. ⦁ Programming key

- For permanent overrides

- For program copy or save

⦁ 300 programmesteps ; ON, OFF, pulses or . ⦁ Permanent overrides On or Off ( permanent light on). ⦁ Temporary overrides On or Off ( flashing). ⦁ Overrides (temporary, permanent or time delayed) remote activation possible. ⦁ Simulation of presence . ⦁ Keyboard lock function by PIN number. ⦁ Counter of operating time on every output. ⦁ Programmable with power off. ⦁ Display with backlight.

Product Presentation

Technical specifications

Electrical characteristics

• Supply voltage 230 V +10/-15%

• Frequency 50/60 Hz

• Power consumption < 2 VA

• Output 2 changeover + 2 NO contacts

• Maximum load

AC1 µ 10A 250 V~ Incandescent lighting: 1500 W Halogen lighting Compensated fluorescent tubes // (max. 45 µF) 400 W Non compensated fluorescent tubes, compensated in series 1000 W Compact fluorescent lamps 400 W

• Minimum load

AC1 100 mA 250 V~

• Galvanic insulation between power supply and output < 4 kV

• Rated impulse voltage 4 kV

Functional characteristics

• Programming capacity 300 steps

• Minimum time between 2 steps 1 minute

• Running accuracy ± 0,2 sec/ 24h

• Operating reserve lithium battery, total of 5 years autonomy (unlimited programme backup)

• The product is set into standby state (display switched-off) after 1 minute with power off. It switches back into automatic mode as soon as power is back on or when pressing any key.

• Protection degree IP 20 / IK 04

• Action type 1B

• Degree of pollution 2

• Software class A

Connection diagram

1 6E 6354E

➀

EG403E

EG001

➁

Environment

• Operating temperature -10 °C to +50 °C

• Storage temperature -20 °C to +70 °C

• Temperature for the ball pressure Test

75° to 125°C

Connection by quick-connect terminals

• Flexible 0,75 to 2,5 mm

• Rigid 0,75 to 2,5 mm

Standards

60730-1 60730-2-7

Usable in all Europe

This device must be installed only by a qualified electrician according to the installation standards in force in the country.

Input for external override

➀ ➁ Option

Warranty

A warranty period of 24 months is offered on hager products, from date of manufacture, relating to any material of manufacturing defect. If any product is found to be defective it must be returned via the installer and supplier (wholesaler). The warranty is withdrawn if:

- after inspection by hager quality control dept the device is

found to have been installed in a manner which is contrary to IEE wiring regulations and accepted practice within the industry at the time of installation.

- The procedure for the return of goods has not been

followed. Explanation of defect must be included when returning goods.

NOT APPLICABLE FOR AUSTRALIA

and in Switzerland

Page 2

CYCLE

CHANNEL D

FUNCTIONS

SETTINGS

CHANNEL C

CHANNEL B

HOLIDAYS

IMPULSE

OFF

MONDAY

BACK AUTO

DELETE

MODIFY

PROGRAM

COPY

PROGRAM

DELETE

PROGRAM

MODIFY

PROGRAM

READ

PROGRAM

CREATE

CHANNEL A

WEEKLY

PROGRAM

YES

MONDAY

SUNDAY

SET

MINUTE

00:00

07:00

CONTINUE PROGRAM

SET HOUR

00:00

FUNCTIONS

SETTINGS

PROGRAM

SETTINGS FUNCTIONS

DATE-TIME

S/W TIME

LANGUAGE

FACTORY SETTINGS

BACK AUTO

PROGRAM

CREATE

PROGRAM

READ

PROGRAM

MODIFY

PROGRAM

DELETE

PROGRAM

COPY

BACK AUTO

COUNTER

CYCLE

PIN CODE

INPUT

BACK AUTO

First commissioning

HOLIDAYS

WEEKLY

BACK AUTO

DELETE

MODIFY

HOLIDAYS

OFF

NOT

REPEATED

VARIABLE

DATE

HOLIDAYS

FIX

DATE

14.07 - 03.08 HOLIDAYS

CONTINUE PROGRAM

START

MONTH

01.07

START

DAY

14.07

END

MONTH

01.

END DAY

03.08

FUNCTIONS

SETTINGS

PROGRAM

COPY

PROGRAM

DELETE

PROGRAM

MODIFY

PROGRAM

READ

PROGRAM

CREATE

PROGRAM

When using for the first time, the following settings must be done:

- select the language

- select the year, month, day

- select the hour and the minutes

- select the automatic change summer/winter.

Press the buttons +/– to set the display. Press OK to validate.

When the settings are finished, the clock goes to automatic mode.

PROGRAM

Creating a holiday programme

The Holiday programme allows you to define one period during which the output contact is on ON or OFF. This programme has the highest priority.

To define your Holiday programme:

Reinitializing

Pressing simultaneously the menu, –, +, ok keys allows you to réinitialize the product. The program is kept in memory.

Press the button menu to access the programming/ setting mode.

All of the programming and adjustments are based on the following principle:

- the 1st line and/or 2nd line of the display indicate the requested setting,

- the buttons +/- allow navigation through the menus and settings,

- the button ok allows validation.

Pressing the button menu allows you to access the following settings:

PROGRAM CREATE

Creating the weekly programme:

The cycle

programme is only possible if one or several cycles have been defined in the FUNCTION/CYCLE menu.

Select:

- FIX DATE: if the programme must be repeated every year at the same dates.

- VARIABLE DATE ( ) if the dates must be recalculated every year according to the dates of Easter.

- NOT REPEATED: if the programme is to be activated once only.

Validate by ok.

PROGRAMME READ

To visualise a programme

To check the steps of the recorded programme without risk of modifying or deleting.

At any time, pressing the button menu allows you to return to the previous choice level.

The number of free program steps is displayed. Press ok to validate. The buttons + and – allow you to scroll the programme steps. At the end of the visualisation, press ok.

6E 6354E2

Page 3

FUNCTIONS

SETTINGS

PROGRAM

FUNCTIONS

BACK

AUTO

INPUT

PIN-CODE

CYCLES

COUNTER

CONTINUE

BACK AUTO

YEAR

01.01.08

MONTH

01.04.08

DAY

30.04.08

30.04.08 HOUR

15:00

30.04.08 MINUTE

15:

BACK

AUTO

FACTORY SETTINGS

LANGUAGE

S/W TIME

DATE/TIME

FUNCTIONS

SETTINGS

PROGRAM

BACK

AUTO

FACTORY SETTINGS

LANGUAGE

S/W TIME

DATE/TIME

BACK

AUTO

FACTORY SETTINGS

LANGUAGE

S/W TIME

SETTINGS

DATE/TIME

FACTORY SETTINGS

LANGUAGE

S/W TIME

DATE/TIME

CONFIRM

RESET

FUNCTIONS

SETTINGS

PROGRAM

FUNCTIONS

SETTINGS

PROGRAM

COPY

PROGRAM

DELETE

PROGRAM

MODIFY

PROGRAM

READ

PROGRAM

CREATE

PROGRAM

FUNCTIONS

SETTINGS

PROGRAM

COPY

PROGRAM

DELETE

PROGRAM

MODIFY

PROGRAM

READ

PROGRAM

CREATE

PROGRAM

FUNCTIONS

BACK

AUTO

FACTORY SETTINGS

LANGUAGE

S/W TIME

DATE/TIME

SETTINGS

PROGRAMME MODIFY

FUNCTIONS

SETTINGS

PROGRAM

COPY

PROGRAM

ELETE

PROGRAM

MODIFY

PROGRAM

READ

PROGRAM

CREATE

PROGRAM

To modify one or several programme steps.

The number of free program steps is displayed. Press ok to validate. The buttons + and – allow you to scroll the programme steps. The button ok allows you to select the programme step to be modified.

PROGRAMME DELETE

The menu delete allows you to erase:

- all of the programme contained in the clock.

- All of the programme on one channels.

- A programme step.

SETTINGS

The setting menu allows you to access the following settings:

DATE-H

Time and day setting

default type

When the USER type is chosen: Define the month, then the week of the change of summer time. Define the month, then the week of the change of winter time. The change always happens between 2 and 3 am. The change always happens on Sunday.

LANGUAGE

Select the language required amongst the following : FRANÇAIS, DEUTSCH, ENGLISH, NEDERLANDS, PORTUGUES, ESPANOL, ITALIANA.

Validate by ok.

FACTORY SETTINGS

Reset to zero

To reset the product to the manufacturer’s configuration, that is to say, erase all of the programme as well as the settings made:

Everything deleted must be confirmed by pressing the button ok.

Press ok to go back to automatic mode. For other settings (automatic changes summer/

PROGRAMME COPY

The copy function allows you to copy a

winter, language, reset), press + and select CONTINUE.

programme from one channel to another.

SUMMER/WINTER

Confirm the complete reset by ok. At the end of the reset to zero, as for the first com-

missioning, the following settings must be done:

- language

- selection of date and time

- Automatic summer/winter change.

Select the type of summer/winter change required and then validate by ok.

Types available:

Select the channel from which you wish to copy the programme.

Type

Select (+, – then ok) the program you wish to copy: WEEKLY, HOLIDAY. Select the channel into which you wish to paste the programme copied. Validate by pressing ok.

Select CONTINUE, if you wish to copy more programs. Select BACK AUTO to go back to the automatic mode.

3 www.hager.com 6E 6354E

EURO*

SUMMER/ WINTER

USA

SUMMER/ WINTER

AUSTRALIA

SUMMER/ WINTER

USER

SUMMER/ WINTER

Start of Summer time

Last Sunday in March

Second Sunday of March

First Sunday in October

Date freely programmed

No change No change

Start of Winter time

Last Sunday in October

First Sunday in November

First Sunday in April

Date freely programmed

Zone of application

European Union

North America

Australia

FUNCTIONS

The functions menu allows you to access the following functions and information:

Page 4

FUNCTIONS

BACK

AUTO

INPUT

PIN-CODE

CYCLES

COUNTER

INPUT

CHANNEL A

BACK

AUTO

WITH

PUSH BUTT

RANDOM

FUNCTION

PERMANENT

OFF

PERMANENT

TIMER

FUNCTION

WITH SWITCH

FUNCTION CHANGEOU

CHANNEL A

YES

CHANNEL D

CONTINUE

COUNTER

FUNCTIONS

INPUT

PIN-CODE

CYCLES

COUNTER

FUNCTIONS

BACK AUTO

INPUT

PIN-CODE

CYCLES

COUNTER

CYCLE

CYCLE 4

CYCLE 3

CYCLE 2

CYCLE 1

ACTIVATE

CANCEL

TEMPO ON

HOUR

00:00 00

TEMPO ON

MINUTE 00:

00 00

TEMPO ON

SECOND

00:00

TEMPO OFF

HOUR

00:00 00

TEMPO OFF

MINUTE 00:

00 00

TEMPO OFF

SECOND

00:00 00

CYCLE

CYCLE 4

CYCLE 3

CYCLE 2

CYCLE 1

ACTIVATE

CANCEL

FUNCTIONS

BACK

UTO

INPUT

PIN-CODE

CYCLES

COUNTER

PIN-CODE

CANCEL

PIN-CODE

ACTIVATE

PIN-CODE

PROG

0000

PIN-CODE

PROG

000

PIN-CODE

PROG

PIN-CODE

PROG

0000

PIN-CODE

CANCEL

PIN-CODE

ACTIVATE

The “Counter” menu allows you to visualise the number operating hours (position ON) for every output, as well as the number of time changes since commissioning. The counter also allows you to visualise the number of operating hours of the clock (product connected to mains supply).

The counters cannot be reset to zero (even after activating the function factory settings).

Press the button menu. Using the buttons + or –, then ok, select the FUNCTIONS menu, then COUNTER.

The first line indicates the number of operating hours of the output. The second line indicates the number of time changes (ON then OFF) done by the output. The buttons + or – allow you to scroll the various indicators. Press the button ok to exit this menu.

CYCLE

In order to create a cycle programme you must have previously defined the operating cycle(s). A cycle is defined by x h, x min, x sec ON then x h, x min, x sec OFF.

This menu allows you to define, modify or deactivate up to 4 different cycles.

During the creation of a programme step, the active cycles appear in the choice of the state of output.

To create or modify a cycle:

To deactivate a cycle:

Deactivating a cycle also deactivates all the programme steps concerned.

PIN-CODE

The menu PIN CODE allows you to lock the clock keyboard.

When the PIN number is active: The symbol flashes to indicate that the function is activated. After 1 minute without action on the product, the keyboard is locked. The symbol indicates that the keyboard is locked. You must enter the PIN number to reactivate the keyboard.

To activate the keyboard lock by PIN code (or modify the PIN code)

With the buttons + or –, select ACTIVATE. Validate by ok.

With the buttons + or –, enter or modify the 4 figures of the PIN number. Validate by ok.

To deactivate the keyboard lock by PIN NUMBER

- Permanent ON

- Random function

• The channel (or channels) concerned by the

override input.

In automatic mode, the symbol indicates that an override coming from the override entry is active.

Key

As soon as the key is present on the switch PROG KEY appears on the screen. Two types of operation:

A. Permanent override: Insert the key into the switch. After 10 seconds the program contained in the key will be executed without clearing the program contained in the time switch. As soon as the key is removed the program of the time switch is again valid.

B. Copy / Save:

The key allows you to save a program contained in the time switch. You can also copy the contents of the key to the clock.

1.Introduce the key PROG KEY appears on the

screen. Press ok.

2.Using + or –, select:

save on key: to save the programme contained in the product, Record in clock: to load the key programme into the time switch, apply key prog: to execute the programme contained in the key without deleting the one present in the device. Key readout: to check the programme contained in the key.

3. Validate your choice by ok. An error message may appear on the screen:

Check the type of key.

The error message remains on display as long as the key is present, but the time switch programme is the one which is executed

Overrides Random operation

By successively pressing the channel command

INPUT

Override input

This menu allows you to define:

• The product which operates the input (push button or switch).

• The function activated:

- inversion of the state of output contact

- time delay ON output activated for an adjustable

time

- Permanent OFF

button. If the output state is On : 1stpress : temporary override. Off and flashing.

Return to automatic mode will take place at the next programme step.

2ndpress : permanent override. Off and are

fixed. This override must be cancelled manually.

3rdpress : forçage permanent. On and sare

fixed. This override must be cancelled manually.

4thpress : Random operation. For the simulation

of presence, as well as the state of output are displayed. Must be cancelled manually. In this case the programme steps are staggered at random in a slot of ± 59 min.

5thpress : return to automatic mode. The state

of output as well as the symbol are displayed.

6E 6354E4

Hager 11.2012 OCOM 115408