L
N
65
EG071
21
43
12 3
O
F
F
z
O
F
F
OFF
on/off Prog
-
+
6
7
4
3
1
5
2
OFF
on/off Prog
-
+
6
7
4
3
1
5
2
L
N
65
EG071
21
43
1
23
6LE002376A
EG071
Function
The EG071 is a programmable time switch for
the automatic control of electrical loads.
It is fully programmable with a maximum of
20 program steps. Each program step can be
applied to one or several days, maximising the
use of each memory location.
The display will flash in case of power failure
to the unit.
The front cover is sealable preventing
unauthorised access after completion of
programming.
Presentation
Display :
1 time.
2 circuit status (ON or OFF)
3 Day of the week (1 = Monday, 2 = Tuesday
.. 7 = Sunday)
1 channel time switch weekly cycle
2. Set the switching time with key “+” or “-”
3. Use the “on/off” button to choose between
circuit ON and circuit OFF.
ON = contact between terminals 2 and 3.
OFF = contact between terminals 1 and 2.
4. Enter the settings by pressing “Prog”.
You must now choose the days of the
week that the settings apply to.
5. With key “+” and “-”, display one after the other
each day of the week and select with key
“on/off” if the program applies to this day or not.
Days to which the switching is to be applied
must be visible at the bottom of the display e.g.
1 2 3 4 5 visible, means switching will be applied
Monday to Friday.
6. Press “Prog” to enter this program step.
If no buttons are pressed within 2 min., the device
switches back to automatic mode without recording
your settings.
7. Program additional time settings by repeating
steps 2 to 6 above (20 max.)
To delete a program step, modify switching time
with keys “+” and “-”, until display -- :-- (between
23 :59 and 00 :00).
8. To record your settings and return to
automatic mode press “Prog” for more
than 2 seconds.
Technical specifications
Electrical characteristics
- supply voltage
230V쓒 +10%/-15% 50/60Hz
240V~ +/-6% 50/60Hz
- power consumption = 1 VA
- output 1 changeover contact
µ 16A - 230V쓒 AC1
µ 3A - 230V쓒 cosϕ= 0.6
- protection degree IP20
- insulation class II
- maximum operating height 2000m
- rated impulse voltage 4 kV
- upstream circuit breaker 16 A
- voltage and current declared for the needs of
EMC emissions tests 230Vv / 0,5 A
Independent panel-mounted (DIN rail) control
device
Functional characteristics
- accuracy ±1min/day at 20°C
- operating reserve
lithium battery total of three years
- action type 1B
- pollution category 2
- software structure class A
Environment
- operating temperature -10 to +50 °C
- storage temperature -10 to +60 °C
Connection tunnel terminals
- flexible 0.5 to 2.5 mm
- rigid 0.5 to 4 mm
Size 10 (17.5 mm)
Electrical connections
2
2
Buttons :
4 “on/off” chooses whether the circuit
is ON or OFF.
5 “Prog” to set the program and scroll
program steps.
6 “reset”
7 “+” and “-” : changes settings.
Time and day setting
Press key “+” or “-”.
A continuous pressure on this key will scroll up
or down minutes, hours and then days.
Programming
1. To start programming, press key
“Prog”, the first program step
flashes.
Hager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com
To turn the circuit ON or OFF
1. press the “on/off” button.
The display flashes.
2. use the “on/off”, button to turn
the circuit ON or OFF.
To switch back in automatic mode, press “on/off”
for more than 2 seconds.
To check your settings
In automatic mode :
Press “Prog” repeatedly to display the day, the time
and the circuit status (ON or OFF).
To switch back to automatic mode, press “Prog”
for more than 2 sec.
To reset the time switch
Press the “reset” button, the program will be
cancelled.
z
Warranty
A warranty period of 24 months is offered on hager
products, from date of manufacture, relating to any material
of manufacturing defect. If any product is found to be
defective it must be returned via the installer and supplier
(wholesaler). The warranty is withdrawn if:
- after inspection by hager quality control dept the device is
found to have been installed in a manner which is contrary
to IEE wiring regulations and accepted practice within the
industry at the time of installation.
- The procedure for the return of goods has not been
followed. Explanation of defect must be included when
returning goods.
Correct Disposal of This product (Waste Electrical & Electronic
Equipment).
(Applicable in the European Union and other European countries
with separate collection systems).
This marking shown on the product or itsliterature indicates that it
hould not be disposed with other household wasted at the end of its working
life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other
commercialwastes of disposal.
Usable in all Europe
NOT APPLICABLE FOR AUSTRALIA
This device must be installed only by
a qualified electrician according to the
installation standards in force in the
country.
and in Switzerland
å
Loading...