hager TRE530, TRE531, TRE510, EE855, TRE511 User Instructions

6LE003093A

TRE51., TRE53.

z

Motion Detectors

solar 220°

User instructions

¨

α

Description

Detection zone

Installation

Adjustments

Shutters

Angle fixing support

Optimal installation height is 2.5m.
The detection zone shall remain free of obstacle.

m 8 m 16

m 2,5

m 0,5

m 16

m 4

LED A LED B

Delay
(lighting time)

Brightness

level

Sensitivity
(change
of range)

1

2

IP55

+ 90°/- 30°

+/-80°

IP55

+ 90°/- 30°

+/-80°

Wall fixing plate

Adjustment potentiometers

Directional detection head

Vertical adjustment

DETECTORS 220°
TRE510 White
TRE511 Anthracite
TRE530 White
TRE531 Anthracite

ACCESSORY FOR

ANGLE FIXING
EE855 White
EE856 Anthracite
52125 White
52126 Anthracite

6LE003093A1

V2.6.0

RFTP

230V~

Bus

30 V

Button J

cfgcfg

cfg

LED C

Button J

Warning :

This device is to be installed only by a
professional electrician fitter according to
local applicable installation standards.

Test and validation of detection
zone

Set potentiometer 2 to Test mode.
The Test mode is available for 3 minutes time
and does not take brightness level into
account.
Each detected movement turns LED A on for 2
seconds.
The associated receiver is not under control.
After 3 minutes without detection, the product
is set back to auto mode.
Limitation of detection zone :
You can limit the detection zone using the
shutters supplied or by inclining the head.

O

The test mode is available only once the
product has been configured.

Mounting

Projection or ceiling mount :

- Fix the wall plate using the supplied screws.

- Clip the detector onto the wall plate

- Tighten the screws to close.
For angle mounting, the wall fixing plate is

fitted between the accessory and
the detector.

Precautions for installation

For optimum detection conditions, please fol­low these recommendations :

- Keep the detector protected from bad
weather, as it is sensitive to these conditions.

- Maintain 1m distance between the light
source and the detector and keep the detec­tor out of the light source.

Product Description and working
principles

This detector allows remote control of one
or more receivers for a given time when a
movement is detected in its detection zone.
This product can be used in two types of
configuration: one detector controls one/seve­ral receiver(s); several transmitters control the
receiver(s).

Operation

The receiver(s) is(are) under control as soon as
the brightness level as set by potentiometer

2

is considered too low and a movement is
adetected.
Upon detection, the time delay is restarted.

If LED A flashes quickly during configuration,
the position of potentiometer 1 is not compa­tible with the selected function.
Product factory reset is recommended before
any new configuration.

Factory return

Keep push-button J depressed until LED
cfg (flashes (>10s), and then release it.
LED cfg is turned o when factory return is
completed.
After factory return, wait 15s before starting
configuration.

Action Adjustments Potentiometer

Use Auto (factory)
settings to set
automatic lighting
turn-on for
a given time.
Only available when
a detector’s time
delay is set.

Auto Settings

Put the Lux potentiometer on
“auto test”.

The settings are predefined :
Lux = ,
(operating at night only)
time = 3 min,

sensitivity = max

Turn automatic
lighting on for
a given time.
Only available when
a detector’s time
delay is set.

Installer settings

Test and confirm
detection zone.

Test mode

Move the potentiometer

2

to “auto test”.

Adjust sensitivity. Allows setting the range

to avoid disturbance.

Configuration (button J )

These detectors can be configured in 3 dierent
ways :

•

quicklink

: tool-free configuration (using product
pushbuttons and LEDs), see User's Instructions
6T7952 supplied with the product.

• TX100/B V2.5.0 or above :
description of product functions available from
the Manufacturer.

• ETS3 or via TR131 : database and description of
application software available from the
Manufacturer.

Configuration by TX100 or ETS

Set the product in configuration mode by pressing

J button once during the teaching session of

TX100 or for addressing with TR131 in ETS.

O

Product factory return is required to change
the configuration mode.

Correct Disposal of This product
(Waste Electrical & Electronic

Equipment).

(Applicable in the European Union and other European
countries with separate collection systems).

This marking shown on the product or its literature
indicates that it hould not be disposed with other
household wasted at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle
it responsibly to promote the sustainable reuse of
material resources.

Household users should contact either the retailer
where they purchased this product, or their local
government oce, for details of where and how they
can take this item for environmentally safe recycling.

Business users should contact their supplier and
check the terms and conditions of the purchase
contract. This product should not be mixed with other
commercial wastes of disposal.

Usable throughout Europe å and in Switzerland

Hager Controls hereby declares that the TRE51., TRE53.

device complies with the essential requirements and other
relevant provisions of Directive 2014/53/EU.

The CE declaration is available on the:

www.hagergroup.com

6LE003093A2