Page 1
THUMB TURN
ASSEMBLY
LATCH MOUNTING PLATE
LATCH
DEADBOLT
STRIKE
WOOD FRAME
REINFORCER
DUST BOX
MOUNTING SCREWS
F OR USE ON DOORS 1-3/8" to 1-3/4"
FOLD HERE
ON DOOR EDGE
1-3/8"
3545
1-3/4"
T E MP L A T E
1-9/16"
40
CAUTION
：
DO NOT DRILL 2-1/8" (54mm) HOLE
THROUGH TO OPPOSITE SIDE OF DOOR
.
(READ INSTRUCTIONS CAREFULLY)
2-1/8" (5 mm) HOLE4
Make 1"(25.4mm) hole at center
of door edge.
2-3/8" ( 60mm ) BACKSET
2-3/4" ( 70mm ) BACKSET
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
(35mm-45mm) THICK
TOOLS REQUIRED FOR NEW INSTALLATION:
(1) Phillips Head Screwdriver
(1) 2-1/8" (54mm) Hole Saw
(1) 1" (25.4mm) Drill Bit
(1) Chisel
TOOLS REQUIRED FOR REPLACEMENT INSTALLATION:
(1) Phillips Head Screwdriver
FOR REMODELING OR NEW CONSTRUCTION:
- Follow all steps
3221 Thumbturn Only Deadbolt
Installation Instructions
1. MARK DOOR
Measure center line of lock; height as desired from finished floor.
Select 2-3/4" or optional 2-3/8" backset, fold and apply template
to interior side of door and mark center of door as indicated on
template. Mark center hole on door face through guide on template.
(See Step 7 for changing latch backset)
3. PREP DOOR
a. b.
Insert latch in hole, keeping latch face parallel to
face of door edge.
Mark outline and remove latch.
2. DRILL HOLES
Drill 1" (25.4 mm) hole
Drill 2-1/8" (54mm) hole
CAUTION:
Do not drill completely through the door face.
Chisel 5/32" (4 mm) deep or
until latch face is flush with door edge.
4-1/8" (105 mm) deep
1-3/16" (31 mm) deep
Refer to Step 5 & 6 when installing latch.
c.
in center of door edge.
on interior door face.
TEMPLATE
HAGER COMPANIES139 Victor Street, St. Louis, MO 63104 (800) 325-9995 FAX (800) 782-0149
7/28/08
Page 2
4. INSTALL STRIKE
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
2-3/8"
BACKSET
2-3/4"
BACKSET
LATCH MOUNTING PLATE
SIDE VIEW ASSEMBLED
LATCH MOUNTING PLATE
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
2-3/8"
BACKSET
2-3/4"
BACKSET
LATCH
CRANK
THUMBTU
RN
ASSEMBLY
TORQUE BLADE
LATCH
PLATE
LATCH MOUNTING PLATE
a. b.
door. Locate strike in jamb
Close
and center line of strike. Open
door and extend line to door stop.
Measure half of door thickness
plus 1/8" from door stop. Vertically
mark centerline for strike.
Drill (2) 1"(25.4 mm) holes 1-1/4" (31.7 mm)
deep in door jamb, 5/16" (8 mm) above and
5/16’" (8 mm) below horizontal center line.
:
CAUTION
Hole must be drilled a full 1-1/4" (31.7 mm)
deep to ensure proper functioning.
5. INSTALL LATCH MOUNTING PLATE
Adjust
backset, see below for details
on adjusting the latch.
Insert
into the holes on the latch.
the latch to the proper
the latch mounting plate
c.
Match screw holes on strike with
vertical centerlines on jamb. Mark
outline of strike and chisel 1/4"
(6.4mm) deep for flush fit of dust
box, wood frame reinforcer, and
strike. Place dust box and wood
frame reinforcer into mortised area
and tighten to the frame using 3"
wood screws. Insert the strike and
tighten to the frame with #8 screws.
6. INSTALL LATCH THUMBTURN ASSEMBLY
7. BACKSET ADJUSTMENT
Insert latch into 1" diameter hole and tighten to the door edge using #8 screws.
Insert torque blade horizontally into latch crank until thumb turn assembly is
flush with door face. Tighten assembly using screws.
Note: When installing on a metal door, the latch mounting plate may be pulled
up against the inside door face as the mounting screws are tightened. This is
normal when installing on a metal door.
To set latch to 2-3/8" setting, pull up Release Switch on both sides.
While holding Release Switch up, slide crosshairs to the 2-3/8" marked hole.
Loading...