3220/3222 Thumbturn Only Deadbolt
FOLD HERE
ON DOOR
EDGE
1-3/8
"
3545
1-3/4"
T E MP L A T E
1-9/16"
40
2-1/8" (5 mm) HOLE4
Mak
e 1"(25.4mm) hole at center
of door edge.
2-3/8" ( 60mm )) BACKSET
2-3/4" ( 70mm )) BACKSET
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1"(25.4mm) HOLE
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
REV.
DESCRIPTION
ECO NO.
DATE
Insert latch and tighten to the door
using
#8 screws.
c.
w/Blank Mounting Plate
Installation Instructions
FOR USE ON DOORS 1-3/8" to 1-3/4"
(35mm-45mm) THICK
TOOLS REQUIRED FOR NEW INSTALLATION:
Phillips Head Screwdriver
(1)
(1)
2-1/8" (54mm) Hole Saw
(1)
1" (25.4mm) Drill Bit
(1)
Chisel
REQUIRED FOR REPLACEMENT INSTALLATION:
TOOLS
(1)
Phillips Head Screwdriver
REMODELING OR NEW CONSTRUCTION:
FOR
- Follow all steps
IF INSTALLING A 3222 RETRO FIT KIT:
- Refer to Step 5 for installation
1. MARK DOOR
THUMB TURN
ASSEMBLY
LATCH
MOUNTING SCREWS
2. DRILL HOLES
BLANK MOUNTING
PLATE
STRIKE
WOOD FRAME
REINFORCER
DUST BOX
3220 SHOWN
3. PREP DOOR
a. b.
Insert
face of door edge.
Mark
Measure center line of lock; height as desired from finished floor.
Select
2-3/4" or optional 2-3/8" backset, fold and apply template
to interior side of door and mark center of door as indicated on
template. Mark center hole on door face through guide on template.
(See Step 6 for changing latch backset)
latch in hole, keeping latch face parallel to
outline and remove latch.
TEMPLATE
5/32" (4 mm) deep or
Chisel
until
latch face is flush with door edge.
Drill 2-1/8" (54 mm) hole through door face as marked for deadbolt.
(It is recommended that holes be drilled from both sides of the
door to prevent splitting). Drill 1” (25.4 mm) hole in center of
door edge for latch.
HAGER COMPANIES139 Victor Street, St. Louis, MO 63104 (800) 325-9995 Fax (800) 782 0149
07/28/08
4. INSTALL STRIKE
5. INSTALL THUMBTURN ASSEMBLY AND BLANK PLATE
a. b.
c.
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
2-3/8"
BACKSET
2-3/4"
BACKSET
LATCH MOUNTING PLATE
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
2-3/8"
BACKSET
2-3/4"
BACKSET
LATCH MOUNTING PLATE
To set latch to 2-3/8" setting, pull up Release Switch on both sides.
While holding Release Switch up, slide crosshairs to the 2-3/8" marked hole.
Close door. Locate strike in jamb
and center line of strike. Open
door and extend line to door stop.
Measure half of door thickness
plus 1/8" from door stop. Vertically
mark centerline for strike.
Drill (2) 1"(25.4 mm) holes 1-1/4" (31.7 mm)
deep in door jamb, 5/16" (8 mm) above and
5/16’" (8 mm) below horizontal center line.
CAUTION
:
Hole must be drilled a full 1-1/4" (31.7 mm)
deep to ensure proper functioning.
Match screw holes on strike with
vertical centerlines on jamb. Mark
outline of strike and chisel 1/4"
(6.4mm) deep for flush fit of dust
box, wood frame reinforcer, and
strike. Place dust box and wood
frame reinforcer into mortised area
and tighten to the frame using 3"
wood screws. Insert the strike and
tighten to the frame with #8 screws.
Insert torque blade horizontally into latch crank until thumb turn assembly is
flush with door face. Place the blank mounting plate on the outside of the door
and line up the threaded posts with the holes of the thumbturn assembly. Insert
the screws thru the holes of the thumbturn assembly and latch body. Tighten
the screws to the threaded posts of the blank mounting plate. Tighten the assembly
so the complete assembly is tight to the door.
6. BACKSET ADJUSTMENT
REV.
DESCRIPTION
ECO NO.
DATE
LATCH
CRANK
TORQUE BLADE
THUMBTURN
ASSEMBLY
BLANK MOUNTING
PLATE
Loading...