Page 1
PETER DE CONINCK HAGENUK RX 1001MVB RECEIVER
ONL4234 SERIAL N° 5820-310-6162
BELGIAN SWL DRAWING N° 97 8 2.164
Technical data
Frequency range :10 kHz to 29999,99 kHz.
Frequency resolution :10 Hz increments.
Keyboard entry or single knob flywheel at 500 Hz or 5
kHz per revolution.
Frequency tuning : 10 Hz, 100 Hz selectable.
Frequency synthesizer : Triple PLL, lowest reference frequency 10 kHz.
Frequency change-over time : Within frequency decades: < 20 ms.
Between frequency decades: ≤ 100 ms.
Frequency stability
Internal frequency standard : 5.10
TXCO – 10 Mhz : 1.10-6 per year.
Additional external standard : Input level: 0 dBm ± 3 dB / 50 Ω.
1 MHz or 10 MHz ( BFO II)
BFO : ± 5 kHz in 10 Hz steps, synthesized.
Channel memory : 99 channels capable of being loaded with
receiver parameters: mode, frequency,
bandwidth, RF gain, preselector and antenna
attenuator.
SCAN functions : SCAN by time.
: SCAN channel per channel.
SCAN stop : Stop time programmable 0.1 – 0.9 s.
: Dwell time 1 – 9 s and ∞.
: AGC threshold 5 – 95 dBµV.
Modes of operation : DSB: A2A, H2A, A3E, H3E.
USB: J3E, R3E, H3E.
LSB: J3E, R3E, H3E.
CW: A1A.
FSK: F1B, F1C, F3C.
Antenna impedance : 50 Ω SWR < 2 : 1 and antenna attenuation = 0 dB.
Max. antenna input voltage : 30 V
100 V
50 V
Input attenuator : 0 dB, 20 dB selectable; manual or automatic.
Spurious emission at antenna : ≤ 1.10
input
Spurious radiations at antenna : ≤ -97dBm.
input
-7
per day.
for 10 kHz to 1.5 MHz – 10 minutes.
EMF
for 1.5 MHz to 30MHz – 10 minutes.
EMF
for 30 MHz to 400 MHz – 10 minutes.
EMF
-9
W.
PAG. 1
Page 2
PETER DE CONINCK HAGENUK RX 1001MVB RECEIVER
ONL4234 SERIAL N° 5820-310-6162
BELGIAN SWL DRAWING N° 97 8 2.164
Image and IF rejection : > 100 dB.
Intermediate frequencies : 1
: 2
st
IF 63.078 MHz.
nd
IF 4.9985 MHz.
IF Output 1 : 30 kHz, 600 Ω, 0 dBm.
IF Output 2 : 4.9985 MHz, 50 Ω, -10 dBm.
AGC characteristics : Output is within 6 dB for input level variation of 120 dB
between 0.5 µV and 500 mV.
( 90 dB for frequency range 10 kHz to 80 kHz)
AGC time constants : Attack Hold Decay
(SSB 30 dB steps)
Long : ≤ 10 ms 1.5 – 3.5 s 0.55 (± 25%)
Short : ≤ 10 ms ----- 0.25 (± 25%)
Sensitivity without HF preselection : A3E B = 6 kHz, m = 0.5
10 dB SINAD with CCITT filter 20….40 kHz ≤ 7 µV
40.…200 kHz ≤ 4 µV
0.2….30 kHz ≤ 3 µV
EMF
EMF
EMF
A1A B = 300 Hz
10….40 kHz ≤ 1 µV
40.…200 kHz ≤ 0.5 µV
0.2….30 kHz ≤ 0.5 µV
EMF
EMF
EMF
J3E B = 0.3 …2.7 kHz
10….40 kHz ≤ 3 µV
0.04…1.6 MHz ≤ 1 µV
1.6….30 MHz ≤ 1 µV
EMF
EMF
EMF
IF Bandwidth
Filter bandwidth ( kHz) : Min. bandwidth ( kHz) Max. bandwidth ( kHz)
6 dB 60 dB
0.1 0.1 0.75
0.15 0.15 0.80
0.3 0.3 0.90
0.6 0.6 1.70
1.5 1.5 4.00
2.4* 2.4 3.80
3.0** 3.0 4.60
6.0 6.0 15.60
* Special SSB design: USB 0.3 to 2.7, LSB –0.3 to –2.7
** Group delay ≤ 800 µsec at f
± 1.2 kHz ( for SSB audio 600 to 800 Hz)
o
Intercept point : 26 dBm ( 1 – 30 MHz).
PAG. 2
Page 3
PETER DE CONINCK HAGENUK RX 1001MVB RECEIVER
ONL4234 SERIAL N° 5820-310-6162
BELGIAN SWL DRAWING N° 97 8 2.164
Crossmodulation : For a wanted signal 60 dBµV
, the interference
EMF
produced by an unwanted signal 20 kHz off-tune
and 90 dBµV
will be more than 30
EMF
dB below standard output.
Intermodulation : Out of band:
3
100 dBµV
(f
rd
order –60dB or better, for two equal signals of
each at fo +50 kHz and fo +100 kHz
EMF
> 200 kHz).
o
In band:
Unwanted signals –45dB for two equal signals of
100 dBµV
(f
> 200 kHz).
o
each at fo +800 Hz and fo +1200 Hz
EMF
Blocking : For a wanted signal 60 dBµV
EMF ,
20 kHz off-tune must exceed 110 dBµV
the output by 3 dB or SINAD < 14 dB.
Level indication
RF LED-band : 0 to 110 dBµV, 10 dB steps.
AF LED-band : -15 to +6 dBm.
Audio outputs
Built-in speaker : 1.5 W.
External speaker : 3W into 4 Ω.
Headphones : 10 mW into 600 Ω.
Line : 0 dBm ± 10 dB adjustable, 600 Ω balanced.
Audio distortion : < 5% for SSB.
for 1 kHz at standard output power < 5% for DSB at 80% modulation.
AF1 output : -7 dBm 600Ω line output for remote control.
AF2 output : -7 dBm 600Ω line output for remote control.
IF output : 30 kHz 600Ω, typically 0 dBm.
BCD frequency output : TTL level.
AGC output : 2 – 3.2 V.
Antenna diversity : 2 – 3.2 V.
Power supplies
AC operation : 110 – 120 V ± 10% - 45 to 400 Hz.
220 – 240V ± 10% - 45 to 400 Hz.
Power consumption 65 VA ± 20%.
DC operation : 21 to 32V floating
Power consumption 50 VA ± 20%.
an unwanted carrier
to effect
EMF
PAG. 3
Page 4
PETER DE CONINCK HAGENUK RX 1001MVB RECEIVER
ONL4234 SERIAL N° 5820-310-6162
BELGIAN SWL DRAWING N° 97 8 2.164
Environmental conditions
Temperature
Operating : -15 to +55 °C.
Storage : -40 to +85 °C.
Humidity : 95% up to 40°C.
Vibration without shockmounts : 0 to 12.5 Hz 3.2 mm amplitude.
12.5 to 25 Hz 0.7 mm amplitude.
25 to 50 Hz 0.4 mm amplitude.
Additional : 0 – 50 Hz 0.3 mm peak to peak.
50 – 500 Hz 2g acceleration.
Shock : 30g, 11 ms all sides.
MILspec : above tests according to respective section of VG95332
Weight : approx. 15 kg.
Dimensions : 19” standard.
Height : 132.5 mm ( 3RU).
Depth : 450 mm ( with handles).
Width : 483 mm.
Option V (Preselector module )
Frequency range : Lowpass filter < 1.6 MHz.
1.6 to 30 MHz; 3-stage bandpassfilter, motor - driven,
microprocessor – controlled.
Input protection : Max. 100 V
U
≤ 100 V
HF
.
eff
and I ≤ 2 A.
eff
Selectivity :
typ. 6 dB , max. 10 dB in bandpass.
Bandpass min. 10 kHz at 3 dB, min. 40 dB at 10%
frequency range.
PAG. 4
Page 5
Page 6
Page 7
Page 8
Page 9
Loading...