Edition : 1.0
Date: (12/24)
Instruction Manual
DELUXE SERIES
TOOL CHEST
TDL-447
Order Code: (T6870)
www.machineryhouse.com.au / www.machineryhouse.co.nz
www.machineryhouse.com.au / www.machineryhouse.co.nz
1
1
BEFORE ASSEMBLING
OIL
DAILY
Please read this instruction manual before assembly.
Before assembly please pay attention to the following points in priority;
Conrmation of components: Before assembling, please conrm all parts arrived and are in good order.
Site for assembly:
Please assemble it on the soft oor such as smooth carpet and annel blanket. When you
assemble on wooden oor, please put thin towels on the oor.
Points for attention when assembling: Please wear gloves to ensure that it can be assembled safely, and use
two persons to help in the assembly process.
SAFETY INFORMATION
1. Persons other than professionals should not disassemble, repair or modify the product.
2. Keep children, infants and pregnant women away from installation places.
3. Center securely within lip on top of roller cabinet.
4. Place on top of matching roller cabinet only.
5. Do not lift while loaded.
6. Do not place objects on top or hang objects off side.
7. Evenly distribute load from bottom up. Uneven loading causes tipping. Be aware of dynamic loading!
Sudden movement may briey create excess load causing tipping.
8. Do not overload and make sure all drawers are closed and locked when moving.
9. Do not open more than one drawer at a time and make sure tools are evenly distributed inside.
10. Do not perform welding, hammering or disassembly work on top plate.
CAUTION: Do not stand on this product. You may
fall which may cause personal injury or product
damage.
CAUTION: Be careful when opening more than one
drawer. The product may become unstable and
tip, which may cause personal injury or product
damage.
CAUTION: Place tool chest inside inner lip on top
of chest or cabinet. Make sure tool chest sits ush
on roller cabinet. Only use matching roller cabinet.
CAUTION: Do not lift while loaded. Have assistant
help place on roller cabinet while using the correct
mechanical lifting aids.
CAUTION: Keep the product on level surfaces. The
product may become unstable and tip if stored or
moved on an un-level surface, which may cause
personal injury or product damage.
CAUTION: Lock the drawers before moving this
product. The drawers could come open and make
the product unstable and tip, which may cause
personal or product damage.
2
SPECIFICATIONS
Overall size: 722 x 482 x 465mm (WxDxH)
Package size: 800 x 548 x 550mm (WxDxH)
4 drawers: 570 x 410 x 75mm (30kg Per Drawer)
Nett Weight: 39kg
Parts Holders
(x2)
Gas Struts (x2) Keys (x2) Foam Liners (x8)
KEY LOCK OPERATION
LID CLOSED - Key Lock will lock the entire tool chest and drawers
LID OPEN - Drawers can be locked separately with lid in the open position.
10G x 15mm
Screws (x4)
3
ASSEMBLY INSTRUCTIONS
TOOLS & ASSISTANCE NEEDED
10,16mm spanners.
Philips Head Screwdriver
*Tools not included
STEP 1.
Storage Holders Installation
• Position the parts holders in-line with the holes on
both sides of the workstation.
• Attach with 2x 10Gx15mm screws per parts holder
and tighten with a Philips head screwdriver as shown
in Fig. 1.
Fig. 1
4
DRAWER OPERATION
1. 2.
Removing the drawers
• Unlock the safety latch and fully extend the
empty drawer.
• Push up the one release lever while pulling
down on the other release lever.
• Pull the drawer outward until it is released
from the drawer slide.
Re-inserting the drawers
• Extend the drawer slides.
• Insert the brackets on each side of the drawer
into the slots in the slides, being careful that
they are properly positioned.
• Once properly inserted, completely close
the drawer to set the slides in their proper
positions and make sure you go all the way
in to engage the safety lock system.
MAINTENANCE
1. Wheel maintenance: Grease the wheels annually using high-quality bearing grease.
2. Drawer maintenance: Lubricate the slides semi-annually with high-quality bearing grease.
5
OIL
DAILY
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should
be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into
approved containers and dispose of the product and fluids according to local regulations.
Imported by
Australian Distributor
Hare & Forbes
Machineryhouse
Sydney - Melbourne
Adelaide - Brisbane - Perth
Ph: 1300 202 200
www.machineryhouse.com.au
New Zealand Distributor
Machineryhouse
Auckland
Christchurch
Ph: 0800 142 326
www.machineryhouse.co.nz
Loading...