Edition : 1.0
Date: (11/24)
Instruction Manual
INDUSTRIAL TOOLING CABINET
TC-900
Order Code: (T775)
www.machineryhouse.com.au / www.machineryhouse.co.nz
www.machineryhouse.com.au / www.machineryhouse.co.nz
1
BEFORE ASSEMBLING
OIL
DAILY
Please read this instruction manual before assembly.
Before assembly please pay attention to the following points in priority;
Confirmation of components: Before assembling, please conrm all parts arrived and are in good order.
Site for assembly:
Please assemble it on the soft oor such as smooth carpet and annel blanket. When you
assemble on wooden oor, please put thin towels on the oor.
Points for attention when assembling: Please wear gloves to ensure that it can be assembled safely, and use
two persons to help in the assembly process.
Matters needing attention for operation:
- Do not use for in proper use.
- Do not use it on inclined surface or uneven places.
- Do not use it when screws and fasteners are loosened.
TOOLS REQUIRED FOR ASSEMBLY
- M6 & M8 spanners
- Phillips Head Screwdriver
2
PARTS LIST
A
B
C
Part No.
A
B
C
D
E
F
G
H
I
J
K
D E F G
H
Description
Cabinet
Foot Bracket set
Feet Bracket Screws
100mm Drawer
200mm Drawer
100mm Drawer Divider
200mm Drawer Divider
Screw
Lock Bracket
Drawer Slide Set
Plastic Buckets Assorted
Qty
1
1
4
4
1
40
20
48
12
6
20
I
K
J
3
ASSEMBLING of Feet
STEP 1: Attach the feet brackets (B) to the base of the
cabinet (A) and x into place with screws (C)
as shown below.
C
B
A
B
B
4
DRAWER ASSEMBLY
STEP 1: Insert drawer dividers (F & G) into
the corresponding drawers (D & E)
as shown below.
F
D
G
STEP 2:
J2
Slide apart the drawer slide sets (J) by pushing
up or down on the plastic release levers (J2).
Now attach brackets (J2) into slots on both sides
of drawers (D & E) and x in place with 2 screws
(H) on each bracket (J2) as shown below.
J1
J
J2
E
STEP 3: Insert the drawer slide brackets
(J1) into slots on at desired height
on both sides of cabinet body then
x in place with 1 x screw (H) per
bracket (J1). Insert the lock bracket
(I) into the slot above the drawer
slide bracket (J1) and x with screw
(H). Height of bracket (I) is adjusted
with the size of drawers.
H
J1
H
I
J1
H
5
DRAWER ASSEMBLY Cont...
STEP 4: Extend the drawer slides (J2). Insert
the brackets on each side of the
drawer into the slots on the slides (J1),
being careful that they are properly
positioned. Once properly inserted,
completely close the drawer to set the
slides in their proper positions.
J1
J2
6
NOTES:
7
OIL
DAILY
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should
be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into
approved containers and dispose of the product and fluids according to local regulations.
Imported by
Australian Distributor
Hare & Forbes
Machineryhouse
Sydney - Melbourne
Adelaide - Brisbane - Perth
Ph: 1300 202 200
www.machineryhouse.com.au
New Zealand Distributor
Machineryhouse
Auckland
Christchurch
Ph: 0800 142 326
www.machineryhouse.co.nz
Loading...