Habitat Vince Assembly Instructions Manual

Assembly Instructions - Please keep for future reference

VINC-3SB-SS14-A

1 2 1

Tools required

Width - 180cm
Depth - 45cm
Height - 75cm

Dimensions

Important - Please read these instructions before assembly

If you need help or have damaged or missing parts, email:

[e-mail] or call: 0344 499 4686

Vince Sideboard 3 Door

30

1

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

Check you have all the
components and tools listed on the
front cover and pages 2.

Remove all fittings from the plastic
bags and separate them into their
groups.

Keep children and animals away
from the work area, small parts
could choke if swallowed.

Make sure you have enough space
to layout the parts before starting.

Do not stand or put weight on the
product, this could cause damage.

Assemble the item as close to its
final position (in the same room) as
possible.

Do not place furniture directly in
front of radiators, fires or any other
source of heat.

Parts of the assembly
will be easier with 2
people.

Assemble on a soft level surface
to avoid damaging the unit or your
floor.

We do not
recommend the
use of power drill/
drivers for inserting

screws, as this could
damage the unit. Only use hand
screwdrivers.

Dispose of all packaging carefully
and responsibly.

The individual wood slats in your
piece of furniture are specially
selected and sorted by hand by
skilled craftsmen. They follow
specific guidelines securing the
quality demands and design
preferences that lay out the form
of this furniture range.

General care and maintenance

If for any reason you should have
problems with your Habitat product,
please contact the store from which
you purchased it.

Please retain your receipt as proof of
purchase.

If you have anycomments or
suggestions regarding this product,
assembly instructions or service

received, please contact the store or
Habitat Head Office via its web site:
www.habitat.co.uk

or write directly to: Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW

General information

1 2

Wood is a living material, affected by
temperature and moisture for a
long period after you start using it.
Thereby, table tops and top plates
will expand and shrink according to
the seasons, and tiny cracks in the
wood that may occur, are some of
the joys of owning a natural product.

Your piece of furniture comes pre-oiled
from the factory but should be re-oiled
regularly to keep it in good order.
Please see re-oiling instructions below.
Legs for coffee and dining tables should
be checked occasionally to ensure they
are fully tightened in place.
Avoid extreme humidity and heat.
Do not place the item close to heat
sources

Clean the surface with a clean,
wrung out cloth. Never use
detergents

Cleaning and care of oiled and lacquered surfaces

Coloured stains like red wine must
be dried off immediately

Smaller stains and marks can be
polished off the oil surfaces of your
furniture (excluding any lacquered
surfaces) with sand paper no 220 or 180

Re-oiling the oiled surfaces of your furniture (excludes lacquered surfaces)

To keep your furniture it in good
order we suggest re-oiling it every 3
to 6 months.
Danish furniture oil can be bought
at any good hardware store (such as
Homebase).

Apply plenty of oil with a clean cloth.
Table tops must be treated
underneath as well as on the top side.
(Be careful that the oil doesn’t drip
onto your floor!)
After 15 minutes, polish with a s
andpaper sponge or fine sandpaper
(no. 150) along the grains of the wood

Polish off remaining oil with a clean,
dry cloth
Do not use the item, until the oil is
completely absorbed

2

BC

Note: There are ‘Batch Code’ labels where shown on the indicated items, these should beretained.

Components - Panels

Please check you have all the panels listed below

If you need help or have damaged or missing parts, email:

[e-mail] or call: 0344 499 4686

1 o

f 1

1. Cabinet

2.

Leg

x 4

BC