Page 1
Winslow Bar stool
Assembly Instructions - Please keep for future reference
600/5580
600/5597
600/5607
Dimensions
Width - 40cm
Depth - 53cm
Height - 100cm
Important
If you need help or have damaged or missing parts, call the
– Please read these instructions fully before starting assembly
Customer Helpline: 08456 400800
Issue 1 - 9/02/10
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Maximum safe weight of
user : 100 kgs.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
1
Page 3
If you have damaged or missing components,
Components - Parts
call the
Please check you have all the panels listed below
Customer Helpline: 08456 400800
1
Chair back x 1
L R
L R
4
Side stretcher rail x 2
Components -
2
Seat x 1
5
Front stretcher rail x 1
Fittings
3
Leg x 2
Please check you have all the panels listed below
Note :The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
Bolt x 8
D
Wood dowel x 2 Screw x 6
B
Spring washer x 8
E
C
Washer x 8
F
Allen key x 1
2
Page 4
Assembly Instructions
Step 1
a:
Insert wood dowels
into each centre hole in
the back of the seat .
Insert bolts
b:
with spring washers
and washers through
the holes at the back of
the seat into the
chair back . Tighten
bolts with allen key .
C
2
1
2
A
B
F
D
a:
2
D
A
b:
Do not fully tighten.
Screw in screw into the
pre - drilled holes on the
side stretcher rail using
screwdriver.
E
4
2
1
B
C
x 2
2
E
4
4
L
R
3
Page 5
Assembly Instructions
Step 2
Fit the front stretcher
a:
5
rail to the front legs.
Screw in screw into the
pre-drilled holes on the
front stretcher rail .
E
5
a:
E
2
Attach legs to front
b:
corners of the seat frame.
Use bolts with spring
washers and washers
into each 2 holes in the
C
front corners. Tighten
bolts with allen key .
Screw in screw into the
pre-drilled holes on the
front stretcher rail
using screwdriver.
B
2
A
F
E
5
b:
X 4
2
C
B
A
5
X 2
E
4
Page 6
Assembly Instructions
Step 3
Note : Stand the chair on
a level floor.
Tighten all bolts.
a:
Sit on the chair to
b:
level the legs.
c:
After sitting test,
re - tighten bolts again,
if adjustment needed.
c:
a:
b:
d:
Highly recommend to
re - tighten all the bolts
again after using the chair
for 7 days.
Note : Please keep
Allen key to re - tighten
all bolts again when
required.
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
d:
4
Loading...