HAAS + SOHN KOMFORT IV 180.18-AL User Manual

Product no.

Description

20 0618618005036

Art. Nr. 0618018109000 V14 A16

Complete product information

, „HAAS+SOHN KOMFORT IV

180.18-AL“

718

1

16

2
3

14

17

13

9
5

18

7

19

Ø100

270150

15

781

Installation of the combustion chamber liner:

Note: Labels with the short designations are attached to the mounting parts.

1. Install first row: first HSM (rear block centre) (top groove rearward), then rear blocks left and right (top groove
rearward) and front blocks.

2. Insert bottom blocks 1, 2 and 3.

3. Insert ash pan (5) and grate (9).

4. Install second row: rear blocks and lateral blocks.

5. Insert insulating block (16) and draught deflector plate (10).
Installation of the insulating block: Insert insulating block (16) with the short edge into the upper sheet steel groove

(see drawing) and let slip into the lower sheet steel groove.
Installation of the draught deflector plate: Insert draught deflector plate (10) slantwise (bevelled corners at the back)
and place it on the lateral sheet steel angles, then lift the front edge and place it on the support plate.

Important: Push the draught deflector plate to the front until the limit stop is reached!
Important: After cleaning of the appliance, or before returning it to service, checks must be carried out to ensure that

the baffle plates are in the correct position (see diagram).
Suitable fuels:

The following fuels are permitted for use in your wood burning stove (see also section 5.1):
Dry, well seasoned, unadulterated wood and wood briquettes which comply with DIN 51731

No.

1

6

2 0618018105300

10

3
5 0618018005600

8

6 0618018015002

20

7 0089000020005
8

12

9 0020100130005

11

10 0050500040005

11
12 0618516075310

13 0420114005371
14 0618018025301
15 0088400060005
16 0050500050005
17 0618018105035
18 0088500050005

19

Body of the stove
Door to the combustion

chamber
Refractory

Ashpan
Supports for the

exhaust flue
Adjustable feet

Secondary air
Grate 260x152
Plate for diverting the

exhaust Glases
angled upwards

Air intake control
Fitting for the door

handle
Door handle

Inspection window
Door spring
Insulating brick
Door latch
Socket for the pipe

supplying air from
outside Ø 100

Air duct
Bottom plate

Description of the system for supplying the air needed for combustion:

The system for supplying the air needed for combustion in stove unit type 180.18-AL has three settings: the primary
air is adjusted by means of the air intake control(11) With the handle in position 2 (‘right’) the primary air. I enters
through the grate, and the primary air II enters through that area of the combustion chamber which is to wards the
front of the stove. With the handle in position 1 (‘middle’) the primary air I only enters via the grate. The amount of
secondary air is set at an optimum level for the unit to provide the necessary ventilation to keep the window clean and
to provide the necessary air for secondary combustion; it is permanently adjusted for increased comfort. The pre­heated secondary air flows past the top end of the inspection window (8).

Air intake control

2

"right"

Primary air I
open

Primary air II
open

Use:
For use when it is heating up and after
fuel has been added

1

"middle"

0

"left"

shut
shut

open
shut

In normal operation
Only for keeping the embers glowing

Connection for providing the air needed for combustion:

In airtight buildings there can be reduction in the oxygen content of the room in which the stove is set up; it must
therefore be ensured that there is adequate ventilation. The stove unit type 180.18-AL therefore offers you the
possibility of drawing in the air needed for combustion from outside. The stove can then be operated without having to
depend on the air within the room. In order to do this the air from outside that is needed for combustion is supplied by
means of a flexible pipe attached to the socket for the pipe (18). It is possible for you to change the position of the pipe
socket to the left, right or rear of the stove unit. The end of the pipe carrying the air must be located in the open air, or
in a well ventilated room situated within the building. Operation of the stove unit in connection with an air conditioning
and ventilation system is permitted. When installing the stove unit in connection with an automatic air conditioning and
ventilation system the end of the pipe supplying the air must not be located in a room which is connected to this
system.

The amount of fuel and adjustment of the air intake control:

Lighting, and heating the appliance up: see sections 5.4, 5.5 and 5.6 in the instructions for use of the stove.
Use the gloves provided to protect you against the heat when operating the air intake control.
Before every addition of fuel, the air intake control is to be closed completely (handle setting ‘left’).

Brennstoffe maximale Brennstoffmenge Primärluft: Luftregler Sekundärluft (ohne

Regelung)

Scheitholz 2 - 3 Scheite (ca. 2 – 2,5 kg) 10 Minuten lang Hebelstellung „2“
Holzbriketts 1 Holzbrikett (2 kg)

Tip for burning wood: Every time the stove is lit leave the appliance in the ‘right’ position until the fuel is
burning well (around 10 minutes). (This time can vary somewhat depending on the amount of draught
and the pressures involved).When adding fuel shut the air intake as indicated.

(rechts), dann Hebelstellung „1“
(Mitte)

offen

Typenbezeichnung:

Variante:

Herstellnummer:
Wärmeleistungsbereich:
Nennwärmeleistung
Zugelassener Brennstoff:
Staub bez.auf 13% O2: 22 mg/Nm³ Wirkungsgrad: 80,3% CO bez. auf 13% O2: 0,10%
Abgastemperatur am Stutzen: 320°C Nox bez. 13% O2: 96 mg/Nm³ HC bez. auf 13% O2: 42 mg/Nm³
Mindestabstände seitlich:
zu brennbaren Bauteilen: hinten:

Prüfstellenkennziffer: 1625 / Prüf Nr. RRF- 29 12 3110

Lesen und befolgen Sie die Bedieungsanleitung!

Mehrfachbelegung des Schornsteins ist zulässig

Kamineinsatz Bauart : EN 13229-W / Zeitbrandfeuerstätte

Prüf Nr. VKF:

HAAS + SOHN OFENTECHNIK GMBH

URSTEIN NORD 67 A-5412 PUCH

Holz, Holzbrikett nach - DIN 51731,

vorne im Strahlungsbereich:

Anbringungsjahr
2013

Komfort – IV 180.18 AL

Komfort-III 180.18-AL

1303180800085

3,9 - 8,3 kW

siehe Aufstellungs-und

Bedienanleitung

80 cm

180.18

8,0 kW

Prüf. Nr.

Stove unit:

Komfort I

V 180.18

-AL:

Kaminbausätze:

Description

intems

Product no.

RRF Oberhausen
stove „Alpes-II“, RRF-40 06 1033

stove „Jura-II“: RRF-40 06 1033
stove “Genf-II” RRF-40 08 1686
stove “Adonis“ RRF-40 12 3013

RRF-29 12 3110

Fitting the combustion chamber lining for the

„HAAS+SOHN Komfort IV 180.18-AL“

HSL

SL

BS1 BS3 BS2

HW

HSR

HSM

BS1 (stone 1) 1 0050110490005
BS2 (stone 2) 1 0050110500005
BS3 (stone 3) 2 0050110480005
SR (stone right) 1 0050110120005
SL (stone left) 1 0050110110005
HSM (stone middle) 2 0050110060005
HSR (stone right) 2 0050110070005
HSL (stone left) 2 0050110140005
IS (isulating brick) 1 0050500050005
Z (plate) 1 0050500040005
ZU (bottom plate)
HW (holder)

IS

ZU

Z

SR

1 0618618005036
3 0618618005035