H3C S5830V2&S5820V2 Switch Series
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W106-20150315
Installation Guide
Copyright © 2011-2015, Hangzhou H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
3
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H
Care, , IRF, NetPilot, Netflow,
SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of
Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage,
use, and disposal of this product must meet the applicable national laws and regulations.
Preface
H3C S5830V2&S5820V2 Switch Series Installation Guide describes the appearance, installation,
power-on, maintenance, and troubleshooting of the H3C S5830V2&S5820V2 Switch Series.
This preface includes:
• Audience
• Conventions
• About the H3C S5830V2 & S5820V2 documentation set
• Obtaining documentation
• Technical support
• Documentation feedback
Audience
This documentation is intended for:
• Network planners
• Field technical support and servicing engineers
• Network administrators working with the S5830V2&S5820V2 series
Conventions
This section describes the conventions used in this documentation set.
Command conventions
Convention Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
[ x | y | ... ]
{ x | y | ... } *
[ x | y | ... ] *
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
Square brackets enclose a set of optional syntax choices separated by vertical bars, from
which you select one or none.
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select at least one.
Asterisk marked square brackets enclose optional syntax choices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n>
# A line that starts with a pound (#) sign is comments.
The argument or keyword and argument combination before the ampersand (&) sign can
be entered 1 to n times.
GUI conventions
Convention Description
Boldface
> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.
Symbols
Convention Description
WARNING
CAUTION
IMPORTANT
NOTE
TIP
Network topology icons
Window names, button names, field names, and menu items are in Boldface. For
example, the New User window appears; click OK.
An alert that calls attention to important information that if not understood or followed can
result in personal injury.
An alert that calls attention to important information that if not understood or followed can
result in data loss, data corruption, or damage to hardware or software.
An alert that calls attention to essential information.
An alert that contains additional or supplementary information.
An alert that provides helpful information.
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports
Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access controller
engine on a unified wired-WLAN switch.
Represents an access point.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security gateway, or
load-balancing device.
Represents a security card, such as a firewall, load-balancing, NetStream, SSL VPN, IPS,
or ACG card.
Port numbering in examples
The port numbers in this document are for illustration only and might be unavailable on your device.
About the H3C S5830V2 & S5820V2 documentation set
The H3C S5830V2 & S5820V2 documentation set includes:
Category Documents
Product description and
specifications
Hardware specifications
and installation
Marketing brochures Describe product specifications and benefits.
Compliance and safety
manual
Installation quick start Provides basic installation instructions.
Installation guide
H3C LSWM1HFANSC &
LSWM1HFANSCB Fan
Assemblies Installation
H3C LSVM1FANSC &
LSVM1FANSCB Fan
Assemblies Installation
H3C SFP/SFP+/XFP
Transceiver Modules
Installation Guide
H3C LSVM1AC650 &
LSVM1DC650 Power
Modules User Manual
Purposes
Provides regulatory information and the safety
instructions that must be followed during installation.
Provides a complete guide to hardware installation
and hardware specifications.
Provides the physical views, specifications,
installation procedures, and removal procedures for
hot-swappable fan assemblies.
Provides physical views, specifications, installation
procedures, and removal procedures for
hot-swappable fan assemblies.
Describes the installation and replacement
procedures for SFP/SFP+/XFP transceiver modules.
Provides the physical views, specifications,
installation procedures, and removal procedures for
the LSVM1AC650 and LSVM1DC650 power
modules.
H3C LSVM1AC300 &
LSVM1DC300 Power
Modules User Manual
Configuration guides
Software configuration
Command references
MIB Companion Describes the MIBs for the software release.
Operations and
maintenance
Release notes
Obtaining documentation
Access the most up-to-date H3C product documentation on the World Wide Web
at http://www.h3c.com
.
Provides the physical views, specifications,
installation procedures, and removal procedures for
the LSVM1AC300 and LSVM1DC300 power
modules.
Describe software features and configuration
procedures.
Provide a quick reference to all available
commands.
Provide information about the product release and
software upgrading.
Loading...